Enlighted CS-D2 Intelligent Light Sensor for Smart Networked Energy Saving Lighting Systems. User Manual PowerPoint Presentation

Enlighted, Inc. Intelligent Light Sensor for Smart Networked Energy Saving Lighting Systems. PowerPoint Presentation

Contents

Users Manual 2 v2

Page 5 Page 6 Page 1
Copyright © 2015 Enlighted Inc. All rights reserved.
All other brand or product names are trademarks of
their respective companies or organizations.
TechnicalSupport
For questions regardingtheinstallation or operation of
this product,contact Enlighted
TechnicalSupport: support@enlightedinc.com
Company Contact Information
Location: 930 Benecia Ave, Sunnyvale, CA 94085
Phone: +1.650.964.1094
Web: enlightedinc.com
FCC and Industry Canada Compliance Information
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
This device complieswith Part 15 of the FCC Rules and Industry
Canadalicense-exempt RSS standard(s). Operation is subjectto the
following two conditions:
•this devicemay not cause harmful interference, AND
•this device must accept anyinterference received, including
interference that may cause undesiredoperation.
Changes or modifications not expressly approved by Enlighted Inc.
could void the user'sauthority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.L'exploitation
est autoriséeauxdeux conditions suivantes:
•l'appareil ne doit pas produire de brouillage,ET
•l'utilisateur de l'appareildoitaccepter tout brouillage
radioélectriquesubi,même si le brouillage est susceptible d'en
compromettre le fonctionnement.
CE
This device complies with the essential requirements and other
relevant requirements of the R&TTE Directive (1999/5/EC. The
equipment is Class 1 radio equipment which can be placed on the
market and be put into service without restrictions in accordance
with article 1(3) of Commission Decision 2000/299/EC (Version July
2014).
Figure 1: Fixture Mount Sensor FS-D22
Fixture Mount Sensor
Model FS-D22
Installation Instructions
Shipped Components
•Enlighted fixture mount sensor
Tools You May Need
•Wire stripper
Supplies You May Need
•18 AWG solid copper wire, rated >= 300V
93-01144-02 Rev04 082115
Model: FS-D22
FCC ID: AQQ-CS-D2
IC: 10138A-CSD2
Page 2 Page 3 Page 4
Caution
•Installation and maintenance must be performed by a
qualified electrician inaccordance with local, state, and
nationalelectrical codes (NEC) and requirements.
Problem Solution
LED not on Check power and wiring
Solid red LED Sensor fault –replace
Red blinking LED Incompatibility between LED driver and
sensor –replace LED driver and if not
resolved, replace sensor
Step Description
1Switch off the circuit breaker supplying power to
the light fixture.
The sensor is designed to mount in a ½ inch trade
size knockout. (All parts of the sensor are inside the
lighting fixture except for the outer ring.) (See Figure
2 and Figure 6). This sensor is for use with the
Philips XSR driver.
2Determine the location for the sensor in the fixture,
and either remove an existing ½ inch knockout or
cut a hole in the fixture. (See Figure 3).
3Measure the distance between the sensor’s
installation location and the LED driver’s “SR
connections”, and cut two lengths of 18 AWG solid
wire that are at least this length plus 1 inch.
4Strip each end of the two wires leaving 3/8 inch of
exposed wire. (See Figure 5)
5Insert one end of the pair of wires in the sensor’s
wire holes and the other end in the LED driver’s “SR
connections” wire holes. (See Figure 4)
6Remove the outer ring from the sensor by
unscrewing it. Keep the spring washer and inner
ring on the sensor and insert the whole assembly
into the knockout that was cut out of the light
fixture. Screw the outer ring back on the sensor.
Tighten firmly, but do no over tighten. (See Figure
5). If you have a thick fixture, do not use the inner
ring.
Note: Make sure that the sensor antenna passes
through the knock out and does not get caught in
the rings or assembly.
7Close the light fixture and restore power to the
fixture.
Installation Steps
Figure 5: Wire stripping detail
Troubleshooting
Figure 3: Sensor locations in a fixture
Figure 6: Sensor attachment to fixture
LED Driver LED
Driver
Note: For any reason, if you need to remove the two wires,
push down on the tabs of the sensor with a pointed device,
and remove the wires while continuing to hold the tab down.
Sensor Antenna
To Enlighted
sensor
To
lamps
Figure 4: Wiring Connection
Figure 2: Sensor Components

Navigation menu