Enlighted CS-D2 Intelligent Light Sensor for Smart Networked Energy Saving Lighting Systems. User Manual PowerPoint Presentation

Download:
Mirror Download [FCC.gov]
Document ID	2724361
Application ID	o4jP1JUZksTqXl05Xb6ikA==
Document Description	Users Manual 1 v2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	26.58kB (332231 bits)
Date Submitted	2015-08-24 00:00:00
Date Available	2015-09-25 00:00:00
Creation Date	2015-08-21 13:09:59
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2015-08-21 13:10:01
Document Title	PowerPoint Presentation
Document Creator	Acrobat PDFMaker 15 for PowerPoint
Document Author:	Enlighted

FCC and Industry Canada Compliance Information
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules and Industry
Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
• this device may not cause harmful interference, AND
• this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by Enlighted Inc.
could void the user's authority to operate the equipment.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes:
• l'appareil ne doit pas produire de brouillage, ET
• l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Copyright © 2015 Enlighted Inc. All rights reserved.
All other brand or product names are trademarks of
their respective companies or organizations.
Compact Sensor (CS-D2)
Installation Instructions
Technical Support
For questions regarding the installation or operation of
this product, contact Enlighted
Technical Support: support@enlightedinc.com
Company Contact Information
Location: 930 Benecia Ave, Sunnyvale, CA 94085
Phone: +1.650.964.1094
Web: enlightedinc.com
Figure 1: Compact Sensor (CS-D2)
CE
This device complies with the essential requirements and other
relevant requirements of the R&TTE Directive (1999/5/EC). The
equipment is Class 1 radio equipment which can be placed on the
market and be put into service without restrictions in accordance
with article 1(3) of Commission Decision 2000/299/EC (Version July
2014).
Shipped Components
• Enlighted Compact Sensor Unit
Items you may Need
• Lock Nut for fixture mounting or
• Spring Arms for Tile mounting
• 18 AWG solid copper wire, rated >=300v
Tools you may Need
• 1” Drill bit
• Hand drill
• Wire stripper
Model: CS-D2
FCC ID: AQQ-CS-D2
IC: 10138A-CSD2
Page 5
Page 6
93-01182-02 Rev04 082115
Page 1
Caution
Fixture Mount Sensor Installation
• Installation and maintenance must be performed by a
qualified electrician in accordance with local, state, and
national electrical codes (NEC) and requirements.
Tile Mount Sensor Installation
Step
Step
1.
Description
Troubleshooting
Problem
Solution
Switch off the circuit breaker supplying power to the light.
LED not on
Check power and wiring
The sensor is designed to mount in a ½ inch trade size
knockout on a fixture. This sensor is for use with the Philips
XSR driver.
Solid red LED
Sensor fault – replace
Red blinking LED
Incompatibility between LED driver and
sensor – replace LED driver and if not
resolved, replace sensor
Description
1.
Switch off the circuit breaker supplying power to the light.
The sensor is designed to mount in a 1-inch hole in the
ceiling tile. This sensor is for use with the Philips XSR driver.
Determine the location for the sensor in the fixture and cut
an existing knockout (½ inch) in the fixture. See Figure 3.
3.
Make a small circular cut (one-inch) in the ceiling tile.
Thread the spring arms around the sensor.
Insert the compact sensor through the hole in the fixture.
Use the lock nut from behind the sensor to fasten the
compact sensor. See Figure 4.
4.
Measure the distance between the sensor’s installation
location and the LED driver’s “SR connections,”. Cut two
lengths of 18 AWG solid wire that are at least this length
plus one inch. Strip each end of the two wires leaving 3/8
inch of exposed wire.
4.
Measure the distance between the sensor’s installation
location and the LED driver’s “SR connections,” and cut
two lengths of 18 AWG solid wire that are at least this
length plus one inch.
5.
Strip each end of the two wires leaving 3/8 inch of exposed
wire.
6.
Insert one end of the pair of wires in the sensor’s wire holes
and the other end in the LED driver’s “SR connections” wire
holes. See Figure 6.
7.
Turn the power on by switching on the circuit
breaker.
5.
Insert one end of the pair of wires into the LED driver’s “SR
connections” wire holes, (see Figure 5), and pull the other
end through the hole in the tile. See Figure 2.
6.
Insert the free end of the pair of wires into the sensor’s wire
hole. See Figure 2.
7.
Push the spring arms together and insert the sensor through
the hole in the tile. See Figure 2.
8.
Turn the power on by switching on the circuit breaker.
Note: For any reason, if you need to remove the two wires,
push down on the tabs located on the rear of the sensor with a
pointed device, and remove the wires while continuing to hold
the tab down.
Locknut
Figure 4: Fixture Mount Sensor
Spring
arms
To
lamps
Push the spring
arms together
and insert the
sensor
Figure 2: Tile Mount Sensor
Page 2
To Enlighted
sensor
Figure 3: Sensor location in a fixture
Page 3
Figure 5: Wiring Connection
Page 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Enlighted
Create Date                     : 2015:08:21 13:09:59-07:00
Modify Date                     : 2015:08:21 13:10:01-07:00
Language                        : EN-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15
Metadata Date                   : 2015:08:21 13:10:01-07:00
Creator Tool                    : Acrobat PDFMaker 15 for PowerPoint
Document ID                     : uuid:78a707ba-cd81-40b6-bc60-f21ed6036257
Instance ID                     : uuid:895491a1-25be-4db3-9ad7-534ba11ad7a1
Format                          : application/pdf
Title                           : PowerPoint Presentation
Creator                         : Enlighted
Producer                        : Adobe PDF Library 15.0
Tag Template ID                 : TC038954999991
Page Layout                     : SinglePage
Page Count                      : 2

EXIF Metadata provided by EXIF.tools