Microsoft Word - SXT2180 UserManualTechnicalGuide Rev 01.doc
Document Creator
PScript5.dll Version 5.2
Document Author:
Harveysung
SXT-2180 CDMA 1XRTT
FIXED WIRELESS TERMINAL
800 MHz CDMA
TECHNICAL MANUAL
VOICE COMMUNICATION and PCO/PTB Application
CDMA FWT SXT-2180
Technical Manual
Before installing your SXT-2180, carefully remove the contents from the shipping carton and check
for evidence of shipping damage. If damage is found, contact your Authorized Sungil Distributor or
shipping agent immediately.
SAFE OPERATION INSTRUCTIONS
IMPORTANT! Before installing or operating this product, read the SAFETY AND GENERAL INFORMATION
section of this guide.
9 Install the unit indoors.
9 Install the unit on a hard, flat surface for proper ventilation.
9 Do not expose the unit to rain or moisture
9 Do not place the unit on or close to sources of heat.
IMPORTANT NOTICES
TERMS AND CONDITIONS FOR USE OF SXT-2180 PRODUCTS ("Product")
These Terms and Conditions are a legal contract between you and SUNGIL Corporation for the title to and use
of the Product.
BY RETAINING AND USING THE PRODUCT AFTER RECEIPT OF IT, YOU AGREE TO THE TERMS AND
CONDITIONS INCLUDING WARRANTY DISCLAIMERS, LIMITATIONS OF LIABILITY AND
INDEMNIFICATION PROVISIONS BELOW. IF YOU DO NOT AGREE TO THE TERMS AND CONDITIONS,
DO NOT USE THE PRODUCT AND IMMEDIATELY RETURN THE UNUSED PRODUCT FOR A COMPLETE
REFUND. You agree to accept sole responsibility for any misuse of the Product by you; and, in addition, any
negligent or illegal act or omission of your or your agents, contractors, servants, employees, or other users of
the Product so long as the Product was obtained from you, in the use and operation of the Product.
SUNGIL Telecom Ltd.
Corporate Headquarters
321 Gongdan-dong, Gumi City, Kyongbuk
730-030, Korea
Sales and Technical Support
Tel: +82-31-714-0038 · Fax: +82-31-714-9888
E-mail: sales@sungiltel.com · http://www.sungiltel.com
2006 SUNGIL Telecom Co. Ltd., All Rights Reserved
CDMA FWT SXT-2180
Technical Manual
Emergency Battery Backup
Checking the Battery
Each Subscriber SXT2180 unit comes with a standard internal battery inside, and can be replaced at your
local After-Service Centers.
Plug in Your Telephone
1) Locate the modular line port on your telephone and plug in one end of a standard phone cord
2) Connect the other end of the phone cord to the telephone port on the side of the Unit.
NOTE: The SXT-2180 does not support direct computer modem (data) operation through the phone port or fax
port.
SXT-2180 OPERATION
Use the LED Status Indicators
1) Power-on the unit
2) The LEDs indicator on the front of the will turn ON. The following table describes the modes and
operations of the indicator.
Status LED
#. √: Don’t care
LED
Section
10
11
12
13
14
15
Power ON
Boot sequence
Initialize done
Activation fail
Exception occur
High
Normal
RSSI
Low
No signal
High
Normal
Low
Battery
Low battery warn
Switch off
No battery
RSSI
Color
Blink
Green
Yellow
Red
Yellow/Red
Yellow
Green
Yellow
Red
Red
√
√
√
√
√
√
√
√
√
√
√
√
BATT
Color
Blink
None
Yellow
Red
√
√
Red
√
√
√
√
√
√
√
√
Green
Yellow
Red
Red
Yellow/Red
None
Description
Booting…
Idle status
MIN/ESN fail, etc..
RSSI < 98dB
98< RSSI < 104dB
RSSI > 104dB
Searching…
Over 3.8V
Over 3.7V
Over 3.4V
Under 3.4V
Battery Strength Indicator
Low battery Tone – Generated alert sound or blink power LED when low battery. In conversation generated
alert sound, not in conversation blink power LED.
CDMA FWT SXT-2180
Technical Manual
Basic Operation
Placing a Call
1) Pick up the handset and listen for a dial tone.
2) Dial the phone number.
Receiving a Call
When your telephone rings, pick up the handset and begin talking.
NOTE: If you hear an incoming call while picking up the handset, you can receive the call by hanging up (placing the
handset on the cradle) immediately. This will cause the phone to start ringing.
Ending a Call
Hang up the phone (place the handset onto the cradle).
Important Tones and Alerts
Normal Dial Tone - When cellular service is available, the receiver emits a standard (steady) dial tone.
No Service Tone - A fast beeping tone indicates that no cellular service is available. At that time, you can check the RSSI
status. The LED of RSSI will be blink with red color.
Outgoing Call Restriction - A slower beeping is an indication that calls may be received, but not made, from this
particular phone.
Ⅰ. Entering User Menu
Pick up the handset
Press Entry code : ‘##XX’ ( ‘XX’ is 2 digit code )
Ex) ‘01’ – SIO
‘02’ – Emergency etc
Select sub menu and input user data.
Now you entered User Menu.
User Menu Table
0. Hidden Menu
1. Ring / Sound
2.Tools
3. Time
4. Activating
CDMA FWT SXT-2180
01. Emergency
02. HOT Line
03. Mirroring
04. A Key
05. Mater Clear
06. Test Call
1. Ring Type
2. Volume
3. DTMF
4. 1Min Alert
5. Svc Alert
1. Caller ID
2. Dial Tone
1. Alarm
2. Auto Send Time
3. Flash Time
4. On Hook Time
1. New Code
2. Outgoing Restrict
3. Reset Phone
4. Voice Privacy
5. Auto Gain Control
Technical Manual
Ⅱ. Hidden Menu
*Note: User MUST input the security lock code when accessing below menu options.
Emergency
‘##01’
- In the Emergency Menu state, you can store 3-address.
- Press 1~3 key to select an address slot, and then wait until you have heard a security tone. It likes as short melody.
- Enter the security lock code, and press desired Emergency Number and then press ‘À’ to save.
- If you press ‘#’ to release.
Ex) ‘##011911*’ – Store number ‘911’ to 1st Emergency Slot.
HOT Line
‘##02’
- In the Hotline Menu state, you can store 1 address.
- To set up the hotline, you should follow two steps
1. Set a hotline number which will be dialed automatically whenever you pick up the handset.
2. Set a hotline time to delay between picking up handset and dialing a hotline number.
- After heard confirmation tone for a lock code, You can set a Hotline number.
- And then press À to store it in a memory for preserving it on power-on/off cycle.
- If you press ‘#’ instead of À, it will be released.
- And then if you stored a hotline number by pressingÀ, you should select hotline delay time from 1sec. to 9sec. Just
press one key from 1 to 9 please.
- And then press À to store your selection.
- If you didn’t select the delay time, it will be set up default time on 2sec.
Ex) ##02 Î enter lock code Î 39533447 + À + confirm tone Î 4 + À
- This example shows you a hotline number was saved with the number are “39533447” and delayed time is 4 secs.
Mirroring
‘##03’
- In the Mirroring menu, you can backup or restore a data of system configuration.
- When you heard a security tone, press the security lock code.
- After then, you can select backup or restore. Press ‘À’ to backup, and ‘#’ to restore.
During ‘backup’ process, the terminal will be reset automatically.
Ex)
##03 Î enter lock code Î À – Performs backing up system values
##03 Î enter lock code Î ‘#’ – Performs restoring system values
A Key
‘##04’
- In the A Key menu, you can make sure that whether A key is valid or not.
- Input 26 digits of the A key what you want to valid.
- After finished input, press ‘À’.
- If the A key was valid, you can hear confirmation tone, but otherwise, you can hear an alert tone.
Ex)
##04 Î 26 digits (20 digits + 6 digits checksum) Î À
Master Clear
‘##05’
- In the Master clear mode, you can reset all setting value in Terminal.
- When it was done, the Terminal is set to Factory initiate.
NOTE: It will be erased all user data like as alarm, dial tone, etc.
Ex)
##05 Î À (Master Clear)
Test Call ( will be used in a lab like CDG2 )
- In the Test call mode, you can.
NEW 8K MARKOV
NEW 13K MARKOV
8K LOOP BACK
13K LOOP BACK
SO54 MARKOV
- Pressing ‘À’ needs for make completed.
CDMA FWT SXT-2180
‘##06’
SO55 LOOP BACK
Technical Manual
Ⅲ. Ring / Sound Menu
Ring Type
‘##11’
- There are 9-ring types.
- When you entered this menu, you can select ‘1~9’. After select one, press ‘À’ to store ring type.
- If you choose ‘0’ key instead of ‘À’, It will be canceled.
- If you press ‘#’ to release.
Ex)
##11+0: Just cancel. It will make a terminal to idle status.
##11+1 Î assigned ring tone Î À : Index 1’s ring tone will be selected.
Volume Type
‘##12’
- In the volume menu, you can contrast ring volume.
- Press ‘1’ to up, and press ‘2’ to down.
- When you determine the volume, press ‘À’ to save, but if you press ‘#’, don’t save the volume value and exit.
DTMF
- In the DTMF menu, you can select DTMF tone length.
- Press ‘À’ to long, press ‘#’ to short DTMF.
‘##13’
1 Min Alert
‘##14’
- In the 1 Min Alert menu, you can set/release to 1 Min alert notify.
- If you press ‘À’ to set this option, the phone will notify alert to you 1 min later in conversation.
- If you want to release this option, press ‘#’.
Service Alert
‘##15’
- In the Svc Alert menu you can set/release to Service alert notify.
- If you press ‘À’ to set this option, the phone will notify alert to you in and out Service Area.
- If you want to release this option, press ‘#’.
CDMA FWT SXT-2180
Technical Manual
Ⅳ. Tools Menu
Caller ID
‘##21’
- In the Caller ID menu, you can select a CID type for your phone type.
- There are 3-types of caller ID.
- After choose one of them and press ‘À’, the item will be stored.
- If you don’t want to set a caller ID, press ‘#’, then release.
1. BELLCORE
2. V.23
3. DTMF
4. None CID (same as ‘#’key)
Dial Tone
‘##22’
- In the Dial tone menu, you can select a dial tone for your country.
- There are 6-types of dial tone type for each country.
- Press ‘À’ to set. Press ‘#’ to release.
1. India
2. Latin America
3. East Europe
4. China / Syria
5. Nicaragua
6. Default
Ex)
##22 + 1 + À : to set a dial tone as an Indian dial tone.
##22 + 6 + À : to set a dial tone as a default dial tone.
CDMA FWT SXT-2180
Technical Manual
Ⅴ. Time Menu
Alarm
‘##31’
- In the alarm menu, you can set a alarm time that you want.
- Enter 4-digits for alarm time as ‘HH-MM’ type.
- If you want to set a alarm time, press ‘À’.
- When you press ‘#’, the alarm time will be released.
Auto send time
‘##32’
- In the Auto send time menu, you can contrast an auto send time.
- There are 10-types. (1sec~10sec)
- When you choose a time, press ‘À’ to set.
- If you press ‘#’, the saved time will be released, and set to a default time (1sec)
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.4
Linearized : No
Page Count : 17
XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6
About : uuid:7c6e714b-9b17-4ff1-b8d7-92ad960aee60
Producer : Acrobat Distiller 6.0 (Windows)
Modify Date : 2006:12:08 18:05:14+09:00
Create Date : 2006:12:08 18:05:14+09:00
Creator Tool : PScript5.dll Version 5.2
Document ID : uuid:3d1ebdbc-3bb7-4cb7-8287-34f8883ba0fb
Format : application/pdf
Title : Microsoft Word - SXT2180 UserManualTechnicalGuide Rev 01.doc
Creator : Harveysung
Author : Harveysung
