Episensor EPIZ31MOD001 ZIGBEE MODULE FOR WIRELESS NETWORKS User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1161681
Application ID	TY6HaMamahQp0fIsv7ULvA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.28kB (191019 bits)
Date Submitted	2009-08-31 00:00:00
Date Available	2009-09-01 00:00:00
Creation Date	2009-03-12 09:47:04
Producing Software	Adobe PDF Library 8.0
Document Lastmod	2009-03-12 09:47:05
Document Title	Users Manual
Document Creator	Acrobat PDFMaker 8.1 for Word
Document Author:	Brendan O'Malley

EpiSensor Z31 ZigBee Module
User Information Sheet
Description:
The EpiLink Z31 ZigBee Module is a compact, programmable device specially designed for the Ember
ZNet ZigBee™ PRO Stack for wireless mesh networks. Using the Ember EM250 radio and microcontroller
chip, it has a 10-pin InSight Adapter port to allow easy programming from Ember Development Kits and
can be programmed as a ZigBee Co-ordinator, Router or End Device. It includes an on-board memory to
allow over-the-air firmware modifications without having to physically access devices that may already
be deployed in the field. The module is only 26.5 x 51 x 5mm, and includes a 20-pin serial, analogue and
digital interface header connector. It can be supplied with an on-board antenna (utilizing tracks on the
printed circuit board to form the antenna) or via a special U.FL connector, an external antenna.
Features:
•
•
•
•
•
•
•
•
•
Compact and rugged device
10-pin InSight adapter port for programming and debugging with Ember development kits
20-pin I/O interface header connector
Powered with 3 volts via the I/O interface header connector or the InSight adapter port
Onboard antenna or external antenna via U.FL connector and U.FL to SMA adapter
3 x Indicator LEDs
Onboard 128K EEPROM to facilitate Ember Multi-Hop Over-the-Air Bootloader Application
Voltage Supervisor Chip which maintains the device in a Reset state in case of low voltages
Boost mode available for additional output power
Specification:
Communications
ZigBee Pro
Radio
2.4 GHz IEEE 802.15.4 compliant transceiver
Microcontroller
Ember EM 250 12MHz XAP2b 16-bit microcontroller core
Memory
128kB Flash EEPROM and 5kB RAM
Regulatory
CE Compliant and FCC Licensed (see Declaration of Conformity for details)
Input Voltage
+3V DC via InSight or I/O connectors
I/O Connector
Dimensions
20 Pin – See data sheet for details
10-Pin – See www.ember.com for details on usage
26.5 x 51 x 5 mm
Output Power
+3dBm transmit power (+5dBm boost mode)
Range
Up to 300 metres direct line of sight, or up to 50 metres in typical indoor conditions
InSight Connector
Power Consumption 2uA in Deep Sleep mode, 48 mA while transmitting in boost mode
Intended Use:
The EpiSensor Z31 ZigBee module is intended for Equipment Manufacturers and System Integrators
who wish to include ZigBee-based communications capability in their products and systems. They
provide a fast and easy way to implement ZigBee wireless networks with a wide variety of I/O options
for capturing sensor data or interfacing to controllers and actuators. Wireless sensor networks are ideal
for eliminating wires, collecting information from hazardous environments and minimizing time and
cost of field installation. Purchasers will need an Ember development kit to program the module. Kits
are available from authorised Ember resellers. See www.ember.com for details
Options:
Antenna option:
USB option:
On board F-antenna or U.FL connector for external antenna
USB connector fitted or not fitted
Model Number Format: Z31-1-2
N: USB circuit and connector not fitted
U: USB circuit and connector fitted
F: Uses on-board F antenna
U: Uses external antenna via U.FL connector
Accessories:
1) U.FL (female) to SMA (male) adapter cable (50 cm)
2) EpiLink External F-Antenna Pod with 1 metre of cable and an SMA (female) connector
3) EpiLink External F-Antenna Pod with 3 metres of cable and an SMA (female) connector
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Moylish Park, Limerick, Ireland.
Tel: 00-353-61-490185
Fax: 00-353-61-490186
E-mail: info@episensor.com
Web: www.episensor.com
Certificate of Conformity
I hereby declare that the EpiLinkZ31 ZigBee module fulfils the requirements of the European R&TTE
directive and that it has been tested and found to be compliant with the following European
harmonized standards:
1.
2.
3.
4.
5.
6.
IEC 60950-1:2006
IEC 60950-1:2005 (2nd Edition)
EN 300 328 V1.7.1
EN 301 489-17 V1.2.1
EN 301 489-01 V1.6.1
EN 50371: 2002
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Warning: Any changes or modifications to the product not expressly approved by EpiSensor could result
in the product ceasing to comply with the regulations and standards that apply in the country of use and
hence void the user's authority to operate the product.
______________
Brendan H O’Malley
Chief Executive
EpiSensor Limited
Registered in Ireland. No: 438937 Registered office: New Garden, Lisnagry, Co. Limerick
Directors: P.G. Carroll (Managing), B.P. Carroll, B. H. O’Malley, P. Coleman, F. Walsh

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2009:03:12 09:47:05Z
Create Date                     : 2009:03:12 09:47:04Z
Metadata Date                   : 2009:03:12 09:47:05Z
Document ID                     : uuid:e9c7caa7-8d29-4d90-b4a4-0e84da16b180
Instance ID                     : uuid:b443da32-bb4f-4481-a13a-2b4e1dd1b805
Format                          : application/pdf
Creator                         :  Brendan O'Malley
Producer                        : Adobe PDF Library 8.0
Page Count                      : 4
Page Layout                     : OneColumn
Author                          :  Brendan O'Malley

EXIF Metadata provided by EXIF.tools