Epson Endeavor Users Manual User

2015-01-23

• FRONT MATTER
• CONTENTS
• INTRODUCTION
  • VGA UTILITIES
  • OPTIONAL EQUIPMENT
    • MEMORY
    • DRIVES
    • OVER DRIVE PROCESSOR
    • MATH COPROCESSOR
    • ALTERNATE VGA INTERFACE
  • HOW TO USE THIS MANUAL
• CHAP 1-USING YOUR COMPUTER
  • TURNING ON THE COMPUTER
  • TURNING OFF THE COMPUTER
  • USING DISKS AND DISK DRIVES
    • HOW DISK STORE DATA
    • TYPES OF DISKETTE DRIVES
    • DRIVE AND DISKETTE INCOMPATIBILITIES
    • CARING FOR DISKETTES AND DISKETTE DRIVES
    • WRITE-PROTECTING DISKETTES
    • INSERTING AND REMOVING DISKETTES
    • USING A SINGLE DISKETTE DRIVE SYSTEM
    • FORMATTING DISKETTES
    • MAKING BACKUP COPIES
    • USING A HARD DISK DRIVE
    • BACKING UP THE HARD DISK
    • CARING FOR YOUR HARD DISK
  • SPECIAL KEYS ON THE KEYBOARD
  • STOPPING A COMMAND OR PROGRAM
  • RESETTING THE COMPUTER
  • USING A PASSWORD
    • CHANGING OR DELETING A PASSWORD
  • CHANGING THE PROCESSOR SPEED
  • PREPARING THE HARD DISK FOR MOVING
  • USING AUTOEXEC.BAT AND OTHER BATCH FILES
• CHAP 2-INSTALLING AND REMOVING OPTIONS
  • HOW TO USE THIS CHAPTER
    • LOCATING THE INTERNAL COMPONENTS
  • REMOVING THE COVER
  • CHANGING THE JUMPER SETTINGS
    • SETTING THE JUMPERS
  • MEMORY MODULES (SIMMS)
    • INSERTING SIMMS
    • REMOVING SIMMS
  • INSTALLING AN OPTION CARD
  • REMOVING AN OPTION CARD
  • REMOVING AN OPTION CARD CONNECTOR BOARD
  • REPLACING THE OPTION CARD CONNECTOR BOARD
  • INSTALLING A NEW PROCESSOR CHIP
  • INCREASING THE VIDEO MEMORY
    • INSTALLING THE MEMORY CHIPS
  • USING THE ALTERNATE VGA INTERFACE
  • USING A DISPLAY ADAPTER CARD
  • REPLACING THE COVER
  • POST-INSTALLATION PROCEDURES
• CHAP 3-INSTALLING AND REMOVING DRIVES
  • HOW TO USE THIS CHAPTER
  • SETTING THE HARD DISK DRIVE JUMPERS
    • WHERE TO GO NEXT
  • INSTALLING A HARD DISK IN THE VERTICAL BAY
    • REMOVING THE MOUNTING FRAMES
    • INSTALLING THE HARD DISK
    • CONNECTING THE CABLES
  • REMOVING A HARD DISK FROM THE VERTICAL BAY
  • INSTALLING A DRIVE IN A HORIZONTAL BAY
    • ATTACHING MOUNTING FRAMES TO A HARD
    • INSTALLING THE DRIVE
    • CONNECTING THE CABLES
  • REMOVING A DRIVE FROM A HORIZONTAL BUY
  • CONNECTING THE HARD DISK DRIVE RIBBION CABLE TO THE SYSTEM BOARD
  • POST-INSTALLATION PROCEDURES
• CHAP 4-RUNNING SYSTEM DIAGNOSTICS
  • STARTING THE PROGAM
    • DELETING TESTS
    • ADDING TESTS
  • RUNNING TESTS
    • RESUMING FROM AN ERROR
  • SYSTEM DIAGNOSTIC TESTS
  • ERROR MESSAGES
• CHAP 5-FORMATTING A HARD DISK
  • STARING THE PROGRAM
    • FORMATTING A NEW DISK
    • REFORMATTING A USED DISK
    • SELECTING AN OPTION
    • SELECTING A DRIVE
  • OPTION 1 FORMAT
    • MODIFYIG THE DEFECTIVE TRACK TABLE
    • FORMATTING THE DISK
  • OPTION 2 DESTRUCTIVE SURFACE ANALYSIS
  • OPTION 3 NON-DESTRUCTIVE SURFACE ANALYSIS
  • EXITING THE PROGRAM
• CHAP 6-TROUBLESHOOTING
  • INDENTIFYING YOUR SYSTEM
  • ERROR MESSAGES
  • THE COMPUTER WON'T START
  • THE COMPUTER DOES NOT RESPOND
    • RESTORING THE POWER SUPPLY
  • PASSWORD PROBLEMS
    • ACCESSING YOUR SYSTEM
  • KEYBOARD PROBLEMS
  • MONITOR PROBLEMS
  • DISKETTE PROBLEMS
  • DISKETTE DRIVE PROBLEMS
  • HARD DISK PROBLEMS
    • INSTALLING THE DRIVE
    • PREPARING THE DRIVE
    • ACCESSING DATA ON THE DRIVE
  • SOFTWARE PROBLEMS
  • PRINTER PROBLEMS
  • OPTION CARD PROBLEMS
  • MOUSE PROBLEMS
  • MEMORY MODULE PROBLEMS
• APPENDIX A-SPECIFICATIONS
  • CPU AND MEMORY
  • CONTROLLERS
  • INTERFACES
  • MASS STORAGE
  • KEYBOARD
  • PHYSICAL CHARACTERISTICS
  • POWER SUPPLY
  • ENVIRONMENTAL REQUIREMENTS
  • POWER SOURCE REQUIREMENTS
  • SYSTEM MEMORY MAP
• GLOSSARY
• INDEX