Epson Fx 2180 Impact Printer Users Manual User
Epson-Epson-Fx-2180-Owner-S-Manual epson-epson-fx-2180-owner-s-manual
2015-03-28
: Epson Epson-Fx-2180-Impact-Printer-Users-Manual-663583 epson-fx-2180-impact-printer-users-manual-663583 epson pdf
Open the PDF directly: View PDF 
.
Page Count: 227 [warning: Documents this large are best viewed by clicking the View PDF Link!]
- FRONT MATTER
- CONTENTS
- GETTING TO KNOW YOUR PRINTER
- CHAP 1-SETTING UP YOUR PRINTER
- CHAP 2-PRINTING ON CONTINUOUS PAPER
- Setting the Paper Release Lever
- Setting the Paper Thickness Lever
- Loading Multi- Part Forms
- Loading Continuous Paper With Labels
- Using the Front Push Tractor
- Using the Rear Push Tractor
- Using the Tractor in the Pull Position
- Switching Between Printing on Continuous Paper and Printing on Single Sheets
- Adjusting the Top- of- Form Position
- Advancing the Paper to the Tear- Off Edge
- CHAP 3-PRINTING ON SINGLE SHEETS
- CHAP 4-USING THE PRINTER SOFTWARE
- CHAP 5-CHANGING PRINTER SETTINGS FROM THE PRINTER'S CONTROL PANEL
- CHAP 6-USING EPSON STATUS MONITOR 2
- CHAP 7-TROUBLESHOOTING
- APPENDIX A-ENHANCING YOUR PRINTER WITH OPTIONS
- APPENDIX B-CLEANING AND TRANSPORTING THE PRINTER
- APPENDIX C-SPECIFICATIONS
- APPENDIX D-CUSTOMER SUPPORT INFORMATION
- GLOSSARY
- INDEX
9-Pin Dot Matrix Printer
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, without the prior written permission of SEIKO EPSON
CORPORATION. The information contained herein is designed only for use with this
EPSON printer. EPSON is not responsible for any use of this information as applied to
other printers.
Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of
this product or third parties for damages, losses, costs, or expenses incurred by the
purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.)
failure to strictly comply with SEIKO EPSON CORPORATION’s operating and
maintenance instructions.
SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising
from the use of any options or any consumable products other than those designated as
Original EPSON Products or EPSON Approved Products by SEIKO EPSON
CORPORATION.
EPSON and EPSON ESC/P are registered trademarks of SEIKO EPSON CORPORATION.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
IBM is a registered trademark of International Business Machines Corporation.
General Notice: Other product names used herein are for identification purposes only and may be
trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 1998 by SEIKO EPSON CORPORATION, Nagano, Japan.
User’s Guide
Proof Sign-off:
Yamanouchi _______
Grady _______
®f-r01
R
Sun-G+ Rev.C
A5 size Front
97/11/14 pass 1
FCC Compliance Statement
For United States Users
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio or television
reception. However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
interference to radio and television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures.
qReorient or relocate the receiving antenna
qIncrease the separation between the
equipment and receiver
qConnect the equipment into an outlet on a
circuit different from that to which the
receiver is connected
qConsult the dealer or an experienced
radio/TV technician for help.
WARNING
The connection of a non-shielded equipment
interface cable to this equipment will invalidate
the FCC Certification of this device and may
cause interference levels which exceed the limits
established by the FCC for this equipment. It is
the responsibility of the user to obtain and use a
shielded equipment interface cable with this
device. If this equipment has more than one
interface connector, do not leave cables
connected to unused interfaces.
Changes or modifications not expressly
approved by the manufacturer could void the
user’s authority to operate the equipment.
For Canadian Users
This Class B digital apparatus meets all
requirements of the Canadian Interference-
Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte
toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
Declaration of Conformity
According to ISO/IEC Guide 22 and EN 45014
Manufacturer: SEIKO EPSON CORPORATION
Address: 3-5, Owa 3-chome, Suwa-shi,
Nagano-ken 392 Japan
Representative: EPSON EUROPE B.V.
Address: Prof. J. H. Bavincklaan 5 1183
AT Amstelveen
The Netherlands
Declares that the Product:
Product Name: Dot Matrix Printer
Type Name: FX-2180
Model: P920B
Conforms to the following Directive(s) and
Norm(s):
Directive 73/23/EEC:
EN 60950
Directive 89/336/EEC:
EN 55022 Class B
EN 61000-3-2
EN 61000-3-3
EN 50082-1
IEC 801-2
IEC 801-3
IEC 801-4
February 1998
Y. Ishii
President of EPSON EUROPE B.V.
L
Sun-G+ Rev.C
A5 size Front
97/11/14 pass 1
ii
Printer Parts
Proof Sign-off:
Yamanouchi _______
Grady _______
edge guides
paper guide cover
paper release
lever
printer cover
paper guide
front paper guide
(closed)
control panel
knob
paper
separator
cover_1
parallel interface
shield plate
ribbon cartridge
paper thickness
lever
tractor
paper tension
unit
cover-2
front edge guides
front paper guide
(open)
cover-3
L
Sun-G+ Rev.C
A5 size Inside front cover
11-14-97 DR, pass 0
Control Panel Buttons and Lights
n = On
f = Flashing
o = Off
Tear Off/Bin button
•Advances continuous paper to the
tear-off position.
•Feeds continuous paper backward from
the tear-off position to the top-of-form
position.
•Selects a cut-sheet feeder bin when the
cut-sheet feeder is installed.
•Enters the card mode to print on
postcards and envelopes. See Chapter 3.
Tear Off/Bin lights
•
f f when continuous paper is in the
tear-off position.
•
o n when bin 1 of the optional cut-sheet
feeder is selected.
•
n o when bin 2 of the optional cut-sheet
feeder is selected.
•
n n when the printer is in the card mode.
Font button
Selects the font.
See Chapter 5.
Font lights
Indicate which
font is selected.
Micro Adjust
When holding down the Pause button for three
seconds, the printer enters the micro adjust mode.
Using the micro adjust feature, you can press the
D
and
U buttons to adjust the top-of-form or tear-off
position. See Chapter 2.
Paper Out light
•On when no paper is
loaded in the selected
paper source or paper
is not loaded correctly.
•Flashes when paper
has not been fully
ejected or a paper
jam has occurred.
Operate button
Turns the printer on
and off. The printer
is off when the top
of this button is
even with the
button protectors.
Pause button
Stops printing
temporarily, and
resumes printing when
pressed again.
Pause light
•On when the printer
is paused.
•Flashes when the
printer is in the micro
adjust mode.
Load/Eject button
•Loads a single sheet of
paper.
•Ejects a single sheet of
paper if a sheet is
loaded.
•Loads continuous paper
from the standby
position.
•Feeds continuous paper
backward to the
standby position.
LF/FF button
•Feeds paper line by
line.
•Ejects a single sheet
or advances
continuous paper
to the next
top-of-form position
when held down.
Pitch button
Selects the font
size. See Chapter 5.
Pitch lights
Indicate what font
size is selected.
PANEL
L
Sun-G+ Rev.C
A5 size cover-1
11-13-97 DR, pass 0
Contents
Getting to Know Your Printer
Easy-to-Use Features . . . . . . . . . . . . . . . . . . . . . . . . 0-2
Available Paper Paths . . . . . . . . . . . . . . . . . . . . . . . 0-3
Printing on continuous paper . . . . . . . . . . . . . . . . . 0-4
Printing on single sheets . . . . . . . . . . . . . . . . . . . . 0-8
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-10
Ribbon Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . 0-10
Important Safety Instructions . . . . . . . . . . . . . . . . . . . 0-11
Print Head Caution Symbol . . . . . . . . . . . . . . . . . . . . 0-12
ENERGY STAR Compliance . . . . . . . . . . . . . . . . . . . . 0-13
For United Kingdom Users . . . . . . . . . . . . . . . . . . . . 0-13
Use of options . . . . . . . . . . . . . . . . . . . . . . . . . . 0-13
Safety information . . . . . . . . . . . . . . . . . . . . . . . . 0-14
How To Use Your Manuals . . . . . . . . . . . . . . . . . . . . 0-15
Warnings, Cautions, and Notes . . . . . . . . . . . . . . . . . . 0-15
Chapter 1 Setting Up the Printer
Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . . 1-2
Choosing a Place for the Printer . . . . . . . . . . . . . . . . . . 1-4
Positioning the continuous paper supply . . . . . . . . . . 1-5
Installing or Replacing the Ribbon Cartridge . . . . . . . . . . 1-6
Attaching the Paper Guide and Paper Separator . . . . . . . . 1-11
Plugging In the Printer . . . . . . . . . . . . . . . . . . . . . . . 1-13
Connecting the Printer to Your Computer . . . . . . . . . . . . 1-14
Installing the Printer Driver on Your PC . . . . . . . . . . . . . 1-15
For Windows 95 or NT 4.0 . . . . . . . . . . . . . . . . . . . 1-16
For Windows 3.1 or NT 3.5x . . . . . . . . . . . . . . . . . . 1-19
For DOS programs . . . . . . . . . . . . . . . . . . . . . . . 1-20
R
Sun-G+ Rev.C
A5 size Front
97/11/14 pass 1
iii
Chapter 2 Printing on Continuous Paper
Setting the Paper Release Lever . . . . . . . . . . . . . . . . . . . 2-2
Setting the Paper Thickness Lever . . . . . . . . . . . . . . . . . 2-3
Loading Multi-Part Forms . . . . . . . . . . . . . . . . . . . . . . 2-5
Turning on the double-strike mode . . . . . . . . . . . . . . 2-6
Loading Continuous Paper With Labels . . . . . . . . . . . . . . 2-7
Removing continuous paper with labels . . . . . . . . . . . . 2-8
Using the Front Push Tractor . . . . . . . . . . . . . . . . . . . . 2-9
Installing the tractor in the front push position . . . . . . . 2-9
Loading paper onto the front push tractor . . . . . . . . . . 2-10
Removing the printed document from the front
push tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Removing the front push tractor . . . . . . . . . . . . . . . . 2-16
Using the Rear Push Tractor . . . . . . . . . . . . . . . . . . . . 2-17
Loading paper onto the rear push tractor . . . . . . . . . . . 2-17
Removing the printed document from the rear
push tractor . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
Using the Tractor in the Pull Position . . . . . . . . . . . . . . . 2-22
Installing the tractor in the pull position . . . . . . . . . . . 2-23
Loading paper onto the pull tractor . . . . . . . . . . . . . . 2-24
Removing paper from the pull tractor . . . . . . . . . . . . . 2-30
Using two tractors in a push and pull combination . . . . . 2-30
Removing the pull tractor . . . . . . . . . . . . . . . . . . . . 2-33
Switching Between Printing on Continuous Paper
and Printing on Single Sheets . . . . . . . . . . . . . . . . . . . 2-35
Switching to printing on single sheets . . . . . . . . . . . . . 2-35
Switching to printing on continuous paper . . . . . . . . . . 2-36
Adjusting the Top-of-Form Position . . . . . . . . . . . . . . . . 2-37
Advancing the Paper to the Tear-Off Edge . . . . . . . . . . . . 2-40
Using the Tear Off/Bin button . . . . . . . . . . . . . . . . . 2-40
Advancing paper to the tear-off position automatically . . 2-41
Adjusting the tear-off position . . . . . . . . . . . . . . . . . 2-41
L
Sun-G+ Rev.C
A5 size Front
97/11/14 pass 1
iv
Chapter 3 Printing on Single Sheets
Using Single Sheets . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Available paper types and paper slots . . . . . . . . . . . . 3-2
Loading single-sheet multi-part forms . . . . . . . . . . . . 3-4
Loading envelopes . . . . . . . . . . . . . . . . . . . . . . . 3-6
Loading postcards . . . . . . . . . . . . . . . . . . . . . . . 3-7
Loading Single Sheets in the Top Paper Slot . . . . . . . . . . . 3-8
Loading Single Sheets in the Front Paper Slot . . . . . . . . . . 3-10
Chapter 4 Using the Printer Software
About Your Printer Software . . . . . . . . . . . . . . . . . . . 4-2
Using the Printer Driver With Windows 95 . . . . . . . . . . . 4-3
Accessing the printer driver from Windows applications . 4-3
Accessing the printer driver from the Start menu . . . . . . 4-5
Printer driver settings overview . . . . . . . . . . . . . . . . 4-5
Using the Printer Driver With Windows 3.1 . . . . . . . . . . . 4-8
Accessing the printer driver from Windows applications . 4-8
Accessing the printer driver from the Control Panel . . . . 4-10
Printer driver settings overview . . . . . . . . . . . . . . . . 4-10
Using the Printer Driver With Windows NT 4.0 . . . . . . . . 4-12
Accessing the printer driver from Windows applications . 4-12
Accessing the printer driver from the Start menu . . . . . . 4-14
Printer driver settings overview . . . . . . . . . . . . . . . . 4-14
Using the Printer Driver With Windows NT 3.5x . . . . . . . . 4-17
Accessing the printer driver from Windows applications . 4-17
Accessing the printer driver from the Control Panel . . . . 4-19
Printer driver settings overview . . . . . . . . . . . . . . . . 4-19
Using the EPSON Remote! Utility . . . . . . . . . . . . . . . . . 4-21
R
Sun-G+ Rev.C
A5 size Front
97/11/14 pass 1
v
Chapter 5 Changing Printer Settings From the Printer’s Control Panel
Selecting a Built-In Font and Pitch . . . . . . . . . . . . . . . . . 5-2
About Your Printer’s Default Settings . . . . . . . . . . . . . . . 5-3
Changing default settings . . . . . . . . . . . . . . . . . . . . 5-8
Chapter 6 Using EPSON Status Monitor 2
About the EPSON Status Monitor 2 Utility . . . . . . . . . . . . 6-2
Installing EPSON Status Monitor 2 . . . . . . . . . . . . . . . . . 6-3
Accessing EPSON Status Monitor 2 . . . . . . . . . . . . . . . . 6-4
Checking Printer Status Information . . . . . . . . . . . . . . . . 6-4
Using the EPSON Status Monitor 2 window . . . . . . . . . 6-4
Using the Printer Status window . . . . . . . . . . . . . . . . 6-9
Making Monitoring Preference Settings . . . . . . . . . . . . . . 6-10
Turning on background monitoring . . . . . . . . . . . . . . 6-11
Using the background monitoring icon . . . . . . . . . . . . 6-12
Chapter 7 Troubleshooting
Using the Error Indicators . . . . . . . . . . . . . . . . . . . . . . 7-2
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . . 7-4
Power supply problems . . . . . . . . . . . . . . . . . . . . . 7-5
Single-sheet paper loading or feeding problems . . . . . . . 7-6
Continuous paper loading or feeding problems . . . . . . . 7-8
Wrong top-of-form position . . . . . . . . . . . . . . . . . . . 7-9
Wrong tear-off position . . . . . . . . . . . . . . . . . . . . . 7-10
Printing or printout quality problems . . . . . . . . . . . . . 7-11
Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . 7-16
Aligning Vertical Lines in Your Printout . . . . . . . . . . . . . 7-17
Printing a Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18
Printing a Hex Dump . . . . . . . . . . . . . . . . . . . . . . . . 7-19
L
Sun-G+ Rev.C
A5 size Front
97/11/14 pass 1
vi
Appendix A Enhancing Your Printer With Options
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Paper handling options . . . . . . . . . . . . . . . . . . . . . A-2
Optional interface cards . . . . . . . . . . . . . . . . . . . . A-3
Using the Optional Cut-Sheet Feeders . . . . . . . . . . . . . . A-4
Installing the high-capacity or double-bin
cut-sheet feeder . . . . . . . . . . . . . . . . . . . . . . . . A-4
Loading paper in the high-capacity cut-sheet feeder . . . . A-6
Selecting the paper source (bin 1 or bin 2) . . . . . . . . . . A-10
Switching between continuous paper and
single-sheet paper in the cut-sheet feeder . . . . . . . . . A-11
Using the Roll Paper Holder . . . . . . . . . . . . . . . . . . . . A-12
Assembling the roll paper holder . . . . . . . . . . . . . . . A-12
Installing the roll paper holder . . . . . . . . . . . . . . . . A-13
Loading roll paper . . . . . . . . . . . . . . . . . . . . . . . A-14
Removing roll paper . . . . . . . . . . . . . . . . . . . . . . A-16
Installing an Interface Card . . . . . . . . . . . . . . . . . . . . A-17
Using the C82305] or C82306] serial interface card . . . . A-18
Appendix B Cleaning and Transporting the Printer
Cleaning the Printer . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Transporting the Printer . . . . . . . . . . . . . . . . . . . . . . B-3
R
Sun-G+ Rev.C
A5 size Front
97/11/14 pass 1
vii
Appendix C Specifications
Printer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Paper alignment . . . . . . . . . . . . . . . . . . . . . . . . . C-7
Printable area . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
Safety approvals . . . . . . . . . . . . . . . . . . . . . . . . . C-10
CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-10
Command Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-11
EPSON ESC/P control codes . . . . . . . . . . . . . . . . . . C-11
IBM 2381 Plus emulation control codes . . . . . . . . . . . . C-15
Character Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . C-16
International character sets for the Italic table . . . . . . . . C-25
Appendix D Customer Support Information
Contacting Customer Support . . . . . . . . . . . . . . . . . . . D-2
For North American Users . . . . . . . . . . . . . . . . . . . . . D-2
For United Kingdom and the Republic of Ireland Users . . . . D-4
Enquiry Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . D-4
Faxon EPSON . . . . . . . . . . . . . . . . . . . . . . . . . . . D-5
EPtec - Bulletin Board Service for latest drivers and
utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-5
World Wide Web . . . . . . . . . . . . . . . . . . . . . . . . . D-5
For Australian Users . . . . . . . . . . . . . . . . . . . . . . . . . D-6
EPSON FAXBACK . . . . . . . . . . . . . . . . . . . . . . . . D-6
EPSON Bulletin Board System . . . . . . . . . . . . . . . . . D-6
Internet URL http://www.epson.com.au . . . . . . . . . . . D-6
Your dealer . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
EPSON Helpdesk . . . . . . . . . . . . . . . . . . . . . . . . . D-7
For Singapore Users . . . . . . . . . . . . . . . . . . . . . . . . . D-7
L
Sun-G+ Rev.C
A5 size Front
97/11/14 pass 1
viii
For Hong Kong Users . . . . . . . . . . . . . . . . . . . . . . . . D-7
Internet home page . . . . . . . . . . . . . . . . . . . . . . . D-8
Electronic bulletin board system . . . . . . . . . . . . . . . D-8
Technical support hotline . . . . . . . . . . . . . . . . . . . D-8
For Philippines Users . . . . . . . . . . . . . . . . . . . . . . . . D-8
Glossary
Index
R
Sun-G+ Rev.C
A5 size Front
97/11/14 pass 1
ix
Getting to Know Your Printer
Your EPSON® FX-2180 9-pin dot matrix printer provides
high-quality printing and great performance in a compact
design. Features include:
qa variety of paper paths to suit your printing needs
qthe ability to handle a wide range of paper types, including
continuous paper, multi-part forms with one original plus
up to six copies, labels, single sheets, envelopes, and
postcards
qhigh-speed printing of up to 500 characters per second at 10
characters per inch
Your printer also comes with printer driver software, the
EPSON Status Monitor 2 utility for Microsoft® Windows® 95
that lets you check the status of your printer quickly and easily,
and other software. In addition, several options are available to
help suit your individual needs.
Proof Sign-off:
Yamanouchi _______
Grady _______ R
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
Getting to Know Your Printer 1
Easy-to-Use Features
This section highlights some easy-to-use features that you’ll
find helpful.
qUse the tear-off feature to save paper.
If you load paper on the front or rear push tractor, you can
use the tear-off feature to advance your continuous paper
to the printer’s tear-off edge when you finish printing. Then
you can easily tear off the printed sheets and save the paper
normally lost between documents. For more information,
see Chapter 2.
qUse the paper release lever to change the paper path
without removing the paper.
Using the paper release lever, you can easily switch to printing
on single sheets without removing the continuous paper
loaded on the front or rear push tractor. You can also easily
switch to printing on continuous paper on a different
tractor. For more information, see Chapter 2.
1-1
L
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
2 Getting to Know Your Printer
qUse the micro adjust feature to adjust the top-of-form and
tear-off positions. See the Glossary for explanations of the
top-of-form and tear-off positions.
The micro adjust feature allows you to move the paper forward
or backward in 1/216-inch increments so that you can
make precise adjustments to the top-of-form and tear-off
positions. For more information, see Chapter 2.
Available Paper Paths
Your printer provides a variety of paper paths for printing on
continuous and single-sheet paper. As described below, paper
can be fed into the printer from the top, front, bottom, or rear.
You select the paper path that best suits your current printing
needs.
paper release
lever 2-1n
R
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
Getting to Know Your Printer 3
Printing on continuous paper
You can choose from three tractor positions (front push, rear
push, and pull) and three paper entry slots (front, rear, and
bottom) for continuous paper printing. This section helps you
determine which paper paths and tractor positions are best for
your continuous paper printing needs. See the appropriate
sections in Chapter 2 for tractor installation and paper loading
instructions.
Using a push tractor
If you often need to tear off sheets of continuous paper (for
example, if you are printing purchase orders or sales slips), it is
best to use a push tractor. This allows you to use the printer’s
tear-off edge to easily tear off printed sheets of continuous
paper at the perforation. Also, when continuous paper is
loaded on a push tractor, you can load single sheets of paper
from the paper guide without removing the continuous paper.
There are two push tractor positions: front and rear. The
tractors are installed in the front push and rear push positions
when the printer is shipped. See the table below for details
about the push positions and the corresponding paper-feeding
paths.
Note:
oAlways load multi-part forms with seven parts (one original plus six
copies) from the front or bottom slot onto the pull tractor.
oThe tractor in the rear push position cannot be removed.
g2-8a
g2-8-1
L
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
4 Getting to Know Your Printer
Tractor position Description
front push
To use this tractor, load paper in the front slot. If you
print on thick paper such as multi-part forms or
continuous paper with labels, load the paper in the
front paper slot because the paper path from this
slot is almost straight. This reduces the chance of
paper jams.
rear push
To use this tractor, load paper in the rear slot. When
you print on multi-part forms that are bound on only
one side by point glueing, load them in the rear
paper slot; the front push tractor cannot feed this
type of form.
Note:
Because thick multi-part forms require a straight
paper path, load them in the front slot.
Caution:
Do not load continuous paper with labels in the rear
slot. If you load continuous paper with labels in the
rear slot, the labels may come off their backing
sheet inside the printer and cause a paper jam.
Using a pull tractor
If you often print on thick or heavy continuous paper, such as
multi-part forms or continuous paper with labels, use a tractor
in the pull position. The pull tractor provides the best paper
jam prevention, and allows you to load continuous paper from
the front, rear, or bottom of the printer. However, you cannot
use the tear-off feature with the pull tractor.
Note:
If you plan to use a pull tractor, you can remove the tractor from the
front push position and install it in the pull position, or you can
purchase the optional pull tractor (C80032]) and install it in the pull
position. See Chapter 2 for instructions.
g2-8aa1
g2-8aa4
R
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
Getting to Know Your Printer 5
As shown in the table below, three paper entry slots are
available for use with the pull tractor: front, bottom, and rear.
Paper slot Description
front
If you print on thick paper such as multi-part forms
or continuous paper with labels, load it using the
front paper slot because the paper path from this
slot is almost straight. This reduces the chance of
paper jams.
bottom
Because the bottom paper slot has the straightest
paper path, it is ideal for printing on thick paper,
such as multi-part forms or continuous paper with
labels.
Note:
When loading paper in the bottom slot, be sure to
use a printer stand with an opening large enough
so that the paper can feed through it without
obstruction.
rear
You can also load continuous paper onto the pull
tractor using the rear slot. When you print on
multi-part forms that are bound on only one side by
point glueing, load it in the rear slot; the printer
cannot feed this type of form from the front or
bottom slot.
Note:
Because thick multi-part forms require a straight
paper path, load them in the front slot.
Caution:
Do not load continuous paper with labels in the rear
slot. If you load continuous paper with labels in the
rear slot, the labels may come off their backing
sheet inside the printer and cause a paper jam.
g2-8aa1
g2-8aa2
g2-8aa4
L
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
6 Getting to Know Your Printer
Using the push and pull tractors in combination
To improve continuous paper feeding and reduce paper jams,
you can use two tractors at the same time. This is especially
helpful for printing on continuous pre-printed forms,
multi-part forms, or labels, and for printing high quality
graphics. When using two tractors in combination, you can
load paper in the front paper slot onto the front push tractor
and the pull tractor, or load paper in the rear paper slot onto
the rear push tractor and the pull tractor.
Combination Description
rear push
and pull
To use the rear push tractor with the pull tractor, you
need to remove the standard tractor that comes in
the front push position and install it in the pull
position.
Note:
Because thick multi-part forms require a straight
paper path, load them in the front slot.
Caution:
Do not load continuous paper with labels onto
the rear push tractor even when it is used in
combination with the pull tractor. If you load
continuous paper with labels onto the rear
push/pull tractor, the labels may come off their
backing sheet inside the printer and cause a
paper jam.
front push
and pull
To use the front push tractor with the pull tractor,
you need to purchase the optional pull tractor
(C80032]) and install it in the pull position.
Note:
For more information on using two tractors in a push and pull
combination, see page 2-30.
g2-8aa4
g2-8aa1
R
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
Getting to Know Your Printer 7
Printing on single sheets
As shown below, your printer has two paper entry slots for
printing on single sheets: top and front. When continuous
paper is loaded on the front or rear push tractor, you can load
single sheets in the top or front slot without removing the
continuous paper.
This section helps you determine which paper slot best suits
your single-sheet printing needs. See Chapter 3 for paper
loading instructions.
Loading paper in the top slot
You can load ordinary single sheets, single-sheet multi-part
forms, envelopes, or postcards in the top slot.
Note:
Load envelopes only in the top slot.
2-9n
L
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
8 Getting to Know Your Printer
Loading paper in the front slot
You can load ordinary single sheets, single-sheet multi-part
forms, or postcards in the front slot.
Note:
Always use the front paper slot to load single-sheet multi-part forms
that are bound by line glueing only at the side.
2-12
R
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
Getting to Know Your Printer 9
Options
Your printer comes with everything necessary to print on
continuous paper and single sheets using a variety of paper
paths. By adding options, such as a cut-sheet feeder, pull
tractor unit, or roll paper holder, you can further expand your
printer’s versatility. Optional interface cards are also available
to supplement your printer’s built-in parallel interface. For
more information on options for your printer, see Appendix A,
“Enhancing Your Printer With Options.”
Ribbon Cartridges
Your printer uses the following ribbon cartridge:
EPSON black Ribbon cartridge S015086
When printing becomes faint, you need to replace the ribbon
cartridge. Genuine EPSON ribbon cartridges are designed and
manufactured to work properly with your EPSON printer.
They ensure proper operation and long life of the print head
and other printer parts.
To replace a used ribbon cartridge, follow the instructions
under “Installing or Replacing the Ribbon Cartridge” on
page 1-6.
L
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
10 Getting to Know Your Printer
Important Safety Instructions
Read all of these instructions and save them for later reference.
Follow all warnings and instructions marked on the printer.
qDo not place the printer on an unstable surface or near a
radiator or heat source.
qPlace the printer on a flat surface. The printer will not
operate properly if it is tilted or at an angle.
qDo not block or cover the openings in the printer’s cabinet.
Do not insert objects through the slots.
qUse only the type of power source indicated on the
printer’s label.
qConnect all equipment to properly grounded power
outlets. Avoid using outlets on the same circuit as
photocopiers or air control systems that regularly switch
on and off.
qDo not use a damaged or frayed power cord.
qIf you use an extension cord with the printer, make sure
the total ampere rating of all devices plugged into the
extension cord does not exceed the cord’s ampere rating.
Also, make sure the total of all devices plugged into the
wall outlet does not exceed the wall outlet’s ampere rating.
qUnplug the printer before cleaning, and clean it with a
damp cloth only.
qDo not spill liquid on the printer.
qExcept as specifically explained in this guide, do not
attempt to service the printer yourself.
R
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
Getting to Know Your Printer 11
qUnplug the printer and refer servicing to qualified service
personnel under the following conditions:
If the power cord or plug is damaged; if liquid has entered
the printer; if the printer has been dropped or the cabinet
damaged; or if the printer does not operate normally or
exhibits a distinct change in performance. Adjust only those
controls that are covered by the operating instructions.
qPrinter parts marked with this symbol may be hot.
Turn off the printer and let it cool for a few minutes
before you touch any printer part marked with this
symbol.
qIf you plan to use the printer in Germany, observe the
following:
To provide adequate short-circuit protection and over-current
protection for this printer, the building installation must be
protected by a 16 Amp circuit breaker.
Note for German-speaking users:
Bei Anschluß des Druckers an die Stromversorgung muß
sichergestellt werden, daß die Gebäudeinstallation mit einem 16
A-Überstromschalter abgesichert ist.
Print Head Caution Symbol
The symbol on the print head indicates that this
part may be hot. Never touch the print head just
after the printer has been used. Let the print head
cool for a few minutes before touching it.
K
K
L
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
12 Getting to Know Your Printer
E
NERGY
S
TAR Compliance
As an ENERGY STAR Partner, EPSON has
determined that this product meets the ENERGY
STAR guidelines for energy efficiency.
The International ENERGY STAR Office Equipment program
is a voluntary partnership with the computer and office
equipment industry to promote the introduction of
energy-efficient personal computers, monitors, printers, fax
machines, and copiers in an effort to reduce air pollution
caused by power generation.
For United Kingdom Users
Use of options
Epson (UK) Limited shall not be liable against any damages
or problems arising from the use of any options or consumable
products other than those designated as Original EPSON
Products or EPSON Approved Products by Epson (UK)
Limited.
R
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
Getting to Know Your Printer 13
Safety information
wWarning: This appliance must be earthed. Refer to rating plate
for voltage and check that the appliance voltage corresponds to
the supply voltage.
Important: The wires in the mains lead fitted to this appliance
are coloured in accordance with the following code:
Green and yellow — Earth
Blue — Neutral
Brown — Live
If you have to fit a plug:
As the colours of the mains lead of this appliance may not
match coloured markings used to identify the terminals in a
plug, please proceed as follows:
The green and yellow wire must be connected to the terminal in
the plug which is marked with the letter E or the Earth symbol (
G).
The blue wire must be connected to the terminal in the plug
marked with the letter N.
The brown wire must be connected to the terminal in the plug
marked with the letter L.
If damage occurs to the plug, replace the cord set or consult a
qualified electrician.
Replace fuses only with a fuse of the correct size and rating.
L
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
14 Getting to Know Your Printer
How To Use Your Manuals
This User’s Guide provides detailed information on setting up
and using your printer. The Quick Reference Guide that also
comes with the printer summarizes basic information on how
to use the printer.
Warnings, Cautions, and Notes
This guide uses the following conventions:
wWarnings must be followed to avoid bodily injury.
cCautions must be observed to avoid damage to your equipment.
Notes contain important information and useful tips on the operation
of your printer.
R
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
Getting to Know Your Printer 15
L
Sun-G+ Rev.c
A5 size Introduction
97/11/14 pass 0
16 Getting to Know Your Printer
Chapter 1
Setting Up the Printer
Proof Sign-off:
Yamanouchi _______
Grady _______
Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Choosing a Place for the Printer . . . . . . . . . . . . . . . . . . 1-4
Positioning the continuous paper supply . . . . . . . . . . . . . 1-5
Installing or Replacing the Ribbon Cartridge . . . . . . . . . . 1-6
Attaching the Paper Guide and Paper Separator . . . . . . . . 1-11
Plugging In the Printer . . . . . . . . . . . . . . . . . . . . . . . 1-13
Connecting the Printer to Your Computer . . . . . . . . . . . . 1-14
Installing the Printer Driver on Your PC . . . . . . . . . . . . . 1-15
For Windows 95 or NT 4.0 . . . . . . . . . . . . . . . . . . . . . . 1-16
For Windows 3.1 or NT 3.5x . . . . . . . . . . . . . . . . . . . . . 1-19
For DOS programs . . . . . . . . . . . . . . . . . . . . . . . . . . 1-20
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-1
Unpacking the Printer
Besides this guide, your printer box should include EPSON
printer software disks, a Notice Sheet, and the following items:
Note:
Depending on your printer model, the power cord may be permanently
attached to the printer. Also, the shape of the power cord plug varies
depending on the country in which you bought your printer; be sure the
plug you have is the right one for your location.
printer
paper guide
power cord
ribbon cartridge
paper separator
screwdriver
new
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-2 Setting Up the Printer
cCaution:
There are several models of the printer designed for different
voltages, and it is not possible to adjust the printer for use with
another voltage. If the label on the back of the printer does not
show the correct voltage for your country, contact your dealer.
You must remove all protective materials packed around and
inside your printer before you set it up and turn on the power.
Follow the directions on the Notice Sheet (packed with the
printer) to remove these materials. A screwdriver has been
provided for removing the transportation screw.
Save all packing and protective materials, including the
transportation screw and the protective locking clips on the
paper tension unit, in case you need to ship the printer in
the future. It should always be transported in its original
packaging or equivalent materials.
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-3
Choosing a Place for the Printer
Follow the guidelines below when selecting a location for your
printer.
TPlace the printer on a flat, stable surface. The printer will
not operate properly if it is tilted or at an angle.
TPlace the printer where you can easily connect it to a
network interface cable, if necessary.
TLeave adequate room around the printer for easy operation
and maintenance.
TAvoid using or storing the printer in places subject to rapid
changes in temperature and humidity. Also keep it away
from direct sunlight, strong light, heat sources, or excessive
moisture or dust.
TAvoid places subject to shocks and vibrations.
TPlace the printer near a wall outlet where you can easily
unplug the power cord.
Note for French-speaking users:
Placez l’imprimante près d’une prise de contact où la fiche peut
être débranchée facilement.
TAvoid electrical outlets controlled by wall switches or
automatic timers. An interruption in power can erase
information in the memory of your printer or computer.
Also avoid outlets on the same circuit as large motors or
other appliances that can cause voltage fluctuations.
TKeep the entire computer system away from potential
sources of electromagnetic interference, such as
loudspeakers or the base units of cordless telephones.
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-4 Setting Up the Printer
TUse a grounded power outlet; do not use an adapter plug.
TMake sure the paper path is clear and unobstructed before
you print on continuous paper. (See the next section.)
If you plan to use a printer stand, follow these guidelines:
TUse a stand that supports at least 26 kg (57.8 lb).
TNever use a stand that tilts the printer. The printer should
always be kept level.
TPosition your printer’s power cord and interface cable so
they do not interfere with paper feeding. If possible, secure
the cables to a leg of the printer stand.
Positioning the continuous paper supply
Before using continuous paper, make sure you line up your
paper supply with the tractor feeder so the paper feeds
smoothly into the printer, as shown below.
g2-8aaa
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-5
Installing or Replacing the Ribbon Cartridge
This section describes how to install or replace the ribbon
cartridge. The installation and replacement procedures are the
same except that you need to remove the used ribbon cartridge
before replacing it with a new one.
EPSON recommends the use of genuine EPSON ribbon
cartridges (S015086). Products not manufactured by EPSON
may cause damage to your printer not covered by EPSON’s
warranties.
wWarning:
You will need to move the print head by hand to install or replace
the ribbon cartridge. If you have just used the printer, the print
head may be hot; let it cool for a few minutes before touching it.
1. Make sure the printer is turned off. The printer is off when
the surface of the Operate button is even with the button
protectors as shown.
cCaution:
Moving the print head while the printer is on may damage
the printer.
2. If the printer is connected to an electrical outlet, unplug it from
the outlet.
g1-10a
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-6 Setting Up the Printer
3. Lift the printer cover by its back edge and then pull it
straight up and off.
4. Make sure that the print head is not hot; if it is, let it cool for
a few minutes before touching it. Then slide the print head
to the ribbon installation position (the indented portion of
the paper tension unit) by hand.
Note:
When you use the pull tractor, you can replace the ribbon cartridge
even though the print head is not positioned in the ribbon
installation position.
i
t1-2
1-3-1
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-7
5. If a used cartridge is installed, grasp the cartridge and pull it
slightly forward and up; the ribbon guide snaps away from
the metal pins behind the print head. Properly dispose of
the used ribbon cartridge.
6. Remove the new ribbon cartridge from the package. Remove
the separator from the middle of the ribbon cartridge and
discard the separator. Then turn the ribbon-tightening knob
in the direction of the arrow to remove any slack in the
ribbon.
ribbon guide
new02
separator
ribbon-tightening knob
1-4
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-8 Setting Up the Printer
7. Hold the cartridge with the ribbon-tightening knob up. Fit
the two front notches of the ribbon cartridge over the small
pegs on each side of the printer as shown below. Then lay
the cartridge flat.
8. Make sure that the two rear notches of the cartridge fit over
the small pegs on each side of the printer. Then gently
press down the cartridge until both ends click into place.
1-5A
1-5B
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-9
9. Lift the ribbon guide of the ribbon cartridge (i) and insert it
firmly over the metal pins behind the print head (t). Make
sure the ribbon is not twisted or creased and that it is in
place behind the print head. Press down the guide until it
clicks into place.
10. Turn the ribbon-tightening knob in the direction of the
arrow to remove any slack in the ribbon as shown above.
Then slide the print head from side to side to make sure
it moves smoothly.
ribbon-tightening
knob
ribbon guide 1-6SU
1-7
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-10 Setting Up the Printer
11. Replace the printer cover by first inserting the front tabs into
the slots on the printer and then lowering the cover until it
clicks into place.
Attaching the Paper Guide and Paper Separator
To install the paper guide and paper separator, follow these
steps:
1. Turn over the paper guide and insert the paper separator’s
tabs into the slots on the paper guide.
i
t1-8
paper separator
paper guide
1-9n
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-11
2. Make sure the paper guide cover is open as shown below.
Attach the paper guide by sliding the slots on the bottom of
the paper guide over the pegs behind the paper tension
unit.
3. Close the paper guide cover.
paper guide cover
paper tension
unit
1-9
1-11
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-12 Setting Up the Printer
Plugging In the Printer
1. Make sure the printer is turned off. The printer is off when
the surface of the Operate button is even with the button
protectors as shown below.
2. Check the label on the back of the printer to make sure its
voltage matches that of your electrical outlet. Also make
sure the plug on your printer’s power cord matches your
electrical outlet.
cCaution:
It is not possible to change the printer’s voltage. If the rated
voltage and your outlet voltage do not match, contact your
dealer for assistance. Do not plug in the power cord.
3. If the power cord is not attached to the printer, plug the
appropriate end into the AC inlet on the back of the printer.
4. Plug the power cord into a properly grounded electrical outlet.
G1-10
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-13
Connecting the Printer to Your Computer
To connect your computer to your printer’s built-in parallel
interface, you need a shielded, twisted-pair parallel cable with
a D-SUB, 25-pin, male connector for your computer and a
36-pin Centronics® compatible connector for the printer.
If your computer requires a different type of printer interface,
you should be able to use one of the optional interfaces
described on page A-3.
Follow the steps below to connect the printer to your computer
using the built-in parallel interface.
1. Make sure both the printer and computer are turned off. The
printer is off when the surface of the Operate button is even
with the button protectors.
2. Plug the cable connector securely into the printer’s interface
connector, and squeeze the wire clips together until they
lock in place on both sides of the connector.
1-16
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-14 Setting Up the Printer
3. If your cable has a ground wire, connect it to the printer’s
ground connector as shown below.
4. Plug the other end of the cable into the computer. (If the cable
has a ground wire at the computer end, attach it to the ground
connector at the back of the computer.)
After you connect the printer to your computer, install the
printer driver software as described in the next section.
Installing the Printer Driver on Your PC
After you connect the printer to your computer, you need to
install the printer driver on your computer. The printer driver
is software that allows your computer to control the printer.
You need to install the printer driver so your Windows
software applications can take full advantage of the printer’s
capabilities. The printer driver is included in the EPSON
printer software disks that come with your printer.
If you are using DOS, see “For DOS programs” on page 1-20.
Note:
Before you install the printer software, it is best to make backup copies of
the EPSON printer software disks.
g1-12-2
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-15
For Windows 95 or NT 4.0
Follow the steps below to install the printer driver for
Windows 95 or NT 4.0. To use the plug-and-play feature to
install the printer driver for Windows 95, see page 1-17.
Note:
Installing the printer driver for Windows NT 4.0 may require network
administration privileges. Ask your network administrator for more
information.
1. Make sure Windows 95 or NT 4.0 is running and the printer is
off.
2. Insert Disk 1 of your printer driver software in a disk drive.
Double-click the My Computer icon, and then double-click
the drive in which you inserted the disk.
3. Double-click the Setup icon, then make sure your printer
icon is selected in the EPSON Printer Driver Setup dialog
box shown below. Click OK and follow the on-screen
instructions.
After you install the printer driver for Windows 95, you can
install the EPSON Status Monitor 2 utility program. See
Chapter 6 for information on installing and using the Status
Monitor.
SUN95
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-16 Setting Up the Printer
Using Windows 95 plug-and-play
If you are using Windows 95 and you want to install the driver
using plug-and-play, follow the steps below.
Note:
You can install the printer driver using plug-and-play only if your
computer has an IEEE-1284 compatible, bidirectional parallel port. See
your computer documentation for more information.
1. Make sure the printer is connected to your computer as
described on page 1-14.
2. Turn off your printer and computer, if necessary.
cCaution:
Whenever you turn off the printer, wait at least five seconds
before turning it back on; otherwise you may damage the
printer.
3. First turn on your printer and then turn on the computer.
Your computer starts loading Windows 95.
4. If you use a password, enter it at the prompt. The New
Hardware Found screen appears and displays your printer’s
model name.
Note:
If you do not see the New Hardware Found screen or if a problem
occurs, click Cancel and follow the instructions under “For Windows
95 or NT 4.0” on page 1-16.
5. Click the Driver from disk provided by hardware
manufacturer radio button.
Note:
Windows 95 may display the New Hardware Found screen again the
next time you turn on your computer. If this happens, select the Do
not install a driver radio button and then click OK. This screen
will not appear again.
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-17
6. Click OK. You see the Install From Disk screen.
7. Insert Disk 1 of your printer driver software in a disk drive.
8. Type A:\Win95 in the Copy manufacturer’s files from box. (If
you inserted the disk in a drive other than drive A, substitute
the appropriate letter.) Then click OK. The Add Printer
Wizard dialog box appears.
9. You can type a unique name for the printer in the Printer name
box. However, we recommend that you keep the default
printer model name as shown.
If this is your only printer or you want to use this printer as the
default printer for Windows 95 applications, select Yes. (No is
the default setting.)
10. Click the Finish button. The program copies the files to your
hard disk and adds an icon to the Printers folder using the
printer model name or the name you selected.
After you install the printer driver for Windows 95, you can
install the EPSON Status Monitor 2 utility program. See
Chapter 6 for information on installing and using the Status
Monitor.
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-18 Setting Up the Printer
For Windows 3.1 or NT 3.5x
Follow the steps below to install the printer driver for
Windows 3.1 or NT 3.5x.
Note:
Installing the printer driver for NT 3.5x may require network
administration privileges. Ask your network administrator for more
information.
1. Make sure Windows 3.1 or NT 3.5x is running and the Program
Manager window is open.
2. Insert Disk 1 of your printer driver software in a disk drive.
3. Choose Run from the File menu. The following dialog box
appears:
4. Type A:\SETUP. (If you inserted the disk in a drive other than
drive A, substitute the appropriate letter.) Then click OK.
The EPSON Printer Driver Setup dialog box appears.
5. Make sure your printer is selected and click OK. Follow the
on-screen instructions.
31run
SUN31
1
R
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
Setting Up the Printer 1-19
For DOS programs
To control the printer from DOS application programs, you
need to select the printer you are using or another available
printer from the printer list of your application.
Choose the EPSON FX-2180 printer at the appropriate step
in the setup or installation procedure of your DOS application
program. If the list in your application does not include the
FX-2180 printer, choose the first available printer from this list:
FX-2170
FX-880/FX-1180
FX-870/1170
FX-850/1050
FX-800/1000
EX-800/1000
FX-85/105
FX-80+/100+
FX-80/100
If none of these printers is listed, choose the first one available
from the following:
FX
LX
RX
MX
EPSON printer
Standard printer
Draft printer
ASCII printer
Note:
If your application does not list a suitable alternative, contact the
software manufacturer to see if an update is available.
L
Sun-G+ Rev.C
A5 size Chapter 1
97/11/14 pass 0
1-20 Setting Up the Printer
Chapter 2
Printing on Continuous Paper
Proof Sign-off:
Yamanouchi _______
Grady _______
Setting the Paper Release Lever . . . . . . . . . . . . . . . . . . 2-2
Setting the Paper Thickness Lever . . . . . . . . . . . . . . . . 2-3
Loading Multi-Part Forms . . . . . . . . . . . . . . . . . . . . . 2-5
Turning on the double-strike mode . . . . . . . . . . . . . . . . . 2-6
Loading Continuous Paper With Labels . . . . . . . . . . . . . 2-7
Removing continuous paper with labels . . . . . . . . . . . . . . 2-8
Using the Front Push Tractor . . . . . . . . . . . . . . . . . . . 2-9
Installing the tractor in the front push position . . . . . . . . . . 2-9
Loading paper onto the front push tractor . . . . . . . . . . . . . 2-10
Removing the printed document from the front push tractor . . . 2-14
Removing the front push tractor . . . . . . . . . . . . . . . . . . 2-16
Using the Rear Push Tractor . . . . . . . . . . . . . . . . . . . . 2-17
Loading paper onto the rear push tractor . . . . . . . . . . . . . 2-17
Removing the printed document from the rear push tractor . . . 2-21
Using the Tractor in the Pull Position . . . . . . . . . . . . . . . 2-22
Installing the tractor in the pull position . . . . . . . . . . . . . 2-23
Loading paper onto the pull tractor . . . . . . . . . . . . . . . . 2-24
Removing paper from the pull tractor . . . . . . . . . . . . . . . 2-30
Using two tractors in a push and pull combination . . . . . . . 2-30
Removing the pull tractor . . . . . . . . . . . . . . . . . . . . . . 2-33
Switching Between Printing on Continuous Paper
and Printing on Single Sheets . . . . . . . . . . . . . . . . . . . 2-35
Switching to printing on single sheets . . . . . . . . . . . . . . . 2-35
Switching to printing on continuous paper . . . . . . . . . . . . 2-36
Adjusting the Top-of-Form Position . . . . . . . . . . . . . . . 2-37
Advancing the Paper to the Tear-Off Edge . . . . . . . . . . . 2-40
Using the Tear Off/Bin button . . . . . . . . . . . . . . . . . . . 2-40
Advancing paper to the tear-off position automatically . . . . . 2-41
Adjusting the tear-off position . . . . . . . . . . . . . . . . . . . 2-41
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-1
Setting the Paper Release Lever
You can load paper in the printer from various paper sources,
such as the front push tractor or the paper guide. You set the
paper release lever to indicate the paper source you want to
use. The table below describes each paper release lever position.
Note:
To decide which paper source and paper path best suits your printing
needs, see “Available Paper Paths” on page 3.
Paper release
lever position Description
Single-sheet position
For loading single-sheet paper from the top or front slot.
For information on loading single sheets, see Chapter 3.
Rear push tractor position
For loading continuous paper from the tractor installed
in the rear push position. Also set the lever to this
position when using the rear push and pull tractors in
combination.
Front push tractor position
For loading continuous paper from the tractor installed
in the front push position. Also set the lever to this
position when using the front push and pull tractors in
combination.
paper release
lever
2-1n
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-2 Printing on Continuous Paper
Paper release
lever position Description
Pull tractor position
For loading continuous paper from the tractor installed
on top of the printer in the pull position. When the
tractor is in the pull position, you can load paper in the
front, rear, or bottom slot.
Note:
You can load two different types of continuous paper onto the front and
rear push tractors, and easily switch between them using the paper
release lever. Before moving the paper release lever, always press the
Load/Eject button to feed the paper in the paper path backward to the
standby position.
Setting the Paper Thickness Lever
Setting the paper thickness lever allows the printer to
accommodate various thicknesses of paper. The paper thickness
lever is located under the printer cover. You can select one of
eight positions identified by the scale next to the lever.
0
1
-
1
3
2
4
5
6
7
paper thickness
lever
2-38n
2-2g
2-4g
2-3g
2-5g
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-3
Use the following table to set the paper thickness lever to
match the thickness of your paper.
Paper type* Lever position
Ordinary (single sheets or continuous paper) 0
Thin paper -1 or 0
Carbonless multi-part forms with:
2 parts (original + 1 copy)
3 parts (original + 2 copies)
4 parts (original + 3 copies)
5 parts (original + 4 copies)
6 parts (original + 5 copies)
7 parts (original + 6 copies)**
1
3
4
5
6
6
Continuous paper with labels 2
Envelopes 4 or 5
Postcards 3
* See Appendix C for complete paper specifications.
**Always load multi-part forms with seven parts (one original plus six copies)
from the front or bottom slot onto the pull tractor.
Note:
RIf the printed image is smeared, you may need to set the paper
thickness lever one position lower to improve print quality.
RIf the printed image is faint or has many gaps, you may need to
set the paper thickness lever one position higher to improve print
quality.
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-4 Printing on Continuous Paper
Loading Multi-Part Forms
You can use carbonless multi-part forms of up to seven parts
(six copies on top of the original). Make sure you set the paper
thickness lever to the proper position based on the number of
layers in your form.
For best results with thick paper such as multi-part forms,
select a straight or almost straight paper path. It is best to load
multi-part forms using:
Tthe front slot and the front push tractor
Tthe front or bottom slot and the pull tractor
Note:
TAlways load multi-part forms with seven parts (one original plus
six copies) in the front or bottom slot and onto the pull tractor.
TYou may want to turn on the double-strike mode as described on
page 2-6 to make sure the printout on the bottom copies appears
correctly.
TWhen loading multi-part forms that are bound on only one side by
point glueing, load them on the rear push tractor or from the rear
slot using the pull tractor.
Except for setting the paper thickness lever, you load
multi-part forms the same way you load ordinary continuous
paper. For details, see the sections on loading continuous paper
later in this chapter.
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-5
Note:
RBe sure your multi-part forms do not exceed 0.46 mm (0.018
inch) in thickness for the printable area and up to 0.9 mm (0.035
inch) for the perforated edges.
RUse multi-part forms only under normal temperature and
humidity conditions, as follows:
Temperature 15 to 25°C (59 to 77°F)
Humidity 30 to 60% RH
RDo not load paper that is damaged, curled or wrinkled.
Turning on the double-strike mode
If the printing on the bottom copies of your thick multi-part
forms is faint, turn on the double-strike mode as described
below.
Note:
TAlways turn on the double-strike mode before printing on
multi-part forms with seven parts.
TThe double-strike mode is available only when the paper thickness
lever is set to a position higher than 3 and the paper release lever is
set to the pull tractor position.
TWhen the printer is in the double-strike mode, the print speed is
reduced.
1. Load your multi-part forms on the pull tractor as described in
this chapter.
2. Make sure that the printer is turned off.
3. While holding down the Font button press the Operate button
to turn on the printer. The printer enters the double-strike
mode.
To exit the double-strike mode, turn off the printer; then hold
down the Font button and press the Operate button to turn
the printer back on.
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-6 Printing on Continuous Paper
Loading Continuous Paper With Labels
When printing on labels, use only the type of labels that are
mounted on continuous backing sheets with sprocket holes for
use with a tractor feeder. Do not try to print on single sheets
with labels because the printer may not feed labels on a shiny
backing sheet properly.
Thick paper, such as continuous paper with labels, requires a
straight or almost straight paper path. You can load labels in
the front (push tractor or pull tractor) or bottom (pull tractor)
paper slot; however, for best results, use the tractor in the pull
position and load paper in the front or bottom paper slot.
You load labels the same way you load ordinary continuous
paper, except you must set the paper thickness lever to 2 before
printing on labels. See “Loading paper onto the pull tractor”
later in this chapter for more information.
cCaution:
TDo not load continuous paper with labels in the rear paper
slot because the paper path from the rear slot is curved;
labels may come off their backing sheet inside the printer
and cause a paper jam.
TNever use the tear-off feature (by pressing the Tear
Off/Bin button or turning on the auto tear-off mode as
described in “About Your Printer’s Default Settings” in
Chapter 5) to feed continuous paper with labels backward;
they may come off their backing sheet and jam the printer.
TBecause labels are sensitive to temperature and humidity, use
them only under normal operating conditions, as follows:
Temperature 15 to 25°C (59 to 77°F)
Humidity 30 to 60%RH
TDo not load continuous paper with labels that is damaged,
curled or wrinkled.
TDo not leave labels loaded in the printer between jobs; they
may curl around the platen and jam when you resume
printing.
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-7
Removing continuous paper with labels
To avoid peeling labels off the backing sheet and jamming the
printer, follow the steps below when you remove continuous
paper with labels from the printer.
1. After you finish printing, tear off the fresh supply of
continuous labels at the perforation nearest the paper entry
slot.
2. Hold down the LF/FF button to eject the remaining labels from
the printer.
cCaution:
Never press the Load/Eject or Tear Off/Bin button. When fed
backward, labels can easily come off the backing sheet and cause a
paper jam.
g3-19
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-8 Printing on Continuous Paper
Using the Front Push Tractor
To use the front push tractor, load continuous paper in the
front slot. For more information on when to use the front push
tractor, see “Available Paper Paths” on page 3.
Note:
The tractors are installed in the front push and rear push positions when
the printer is shipped. The rear push tractor cannot be removed.
Installing the tractor in the front push position
If a tractor is installed in the front push position, skip to “Loading
paper onto the front push tractor“ on the next page.
If a tractor is installed in the pull position, you need to remove
it, and replace the paper tension unit as described on page 2-33
before using the front push tractor.
To install the tractor in the front push position, follow these
steps:
1. Make sure the printer is turned off.
2. Open the front paper guide by pulling the tab at the center
of the guide. Then remove the guide by grasping both sides
and pulling it straight out of the printer.
tab
2-10
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-9
3. Insert the tractor into the printer’s mounting slots and press
down both ends of the tractor to make sure that it is firmly
seated.
You are now ready to load continuous paper onto the front
push tractor as described in the next section. To remove the
tractor, see page 2-16.
Loading paper onto the front push tractor
To load paper onto the front push tractor, follow these steps:
1. Open the front paper guide by pulling the tab at the center
of the guide. Then remove the guide by grasping both sides
and pulling it straight out of the printer. Check that the
tractor is installed in the front push position.
2-17
2-20
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-10 Printing on Continuous Paper
2. Set the paper release lever to the front push tractor position.
Also set the paper thickness lever (located under the
printer cover) to the proper position for your paper’s
thickness.
3. Release the left and right sprockets by pushing the sprocket
lock levers backward.
2-20a
2-21
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-11
4. Slide the left sprocket to the left margin of your paper using
the arrow mark inside the printer. (Printing starts at the
arrow mark.) Then pull the lever forward to lock it in place.
Note:
See “Paper alignment” and “Printable area” in Appendix C for more
information on the left margin position.
5. Slide the right sprocket to match the width of your paper, but
do not lock it. Move the paper support midway between the
two sprockets as shown above.
6. Open both sprocket covers. Make sure your paper has a
clean, straight edge and fit the first four holes of the paper,
printable side up, over the tractor pins. Then close the
sprocket covers.
2-22
2-23
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-12 Printing on Continuous Paper
7. Slide the right sprocket to remove any slack in the paper; then
lock it in place by pushing the sprocket lock down.
8. Attach the front paper guide by sliding it along the printer’s
mounting slots as shown below. Then close the front paper
guide.
9. Slide the edge guides to the middle of the top paper guide.
Make sure that the printer cover and the paper guide cover
are closed.
Note:
Always close the printer cover before printing. The printer does not
print when the cover is open.
2-24
2-24a
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-13
10. Make sure the printer is on. You may need to check and change
the printer driver settings as described in Chapter 4. When the
printer receives data, it automatically loads the paper and
starts printing. The printed pages are fed over the paper guide
toward the back of the printer.
11. After you finish printing, follow the steps in the next section to
tear off your printed document.
If the first printed line on your page appears too high or low,
you can fix this using the micro adjust feature as described in
“Adjusting the Top-of-Form Position” on page 2-37.
cCaution:
Never use the knob to adjust the top-of-form position; this may
damage the printer or cause it to lose the top-of-form position.
Removing the printed document from the front push
tractor
To remove the printed document, follow these steps:
1. Make sure the Tear/Off Bin lights are flashing. (This indicates
your paper is at the current tear-off position.) You may need to
press the Tear Off/Bin button to advance the paper to the
tear-off position.
2-35a
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-14 Printing on Continuous Paper
2. Open the paper guide cover, and tear off the printed
document using the tear-off edge of the printer.
Note:
If your paper’s perforation is not properly aligned with the tear-off
edge, you can adjust the tear-off position using the micro adjust
feature. See “Adjusting the tear-off position” on page 2-41.
cCaution:
Never use the knob to adjust the tear-off position; this may
damage the printer or cause it to lose the tear-off position.
3. Close the paper guide cover.
When you resume printing, the printer automatically feeds the
paper back to the top-of-form position and starts printing.
To remove the remaining paper from the printer, press the
Load/Eject button to feed the paper backward to the standby
position. (See the Glossary for an explanation of the standby
position.) Then open the sprocket covers of the tractor and
remove the paper.
cCaution:
Always tear off your printed document before you press the
Load/Eject button. Reverse feeding several pages at a time may
cause a paper jam.
1-1
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-15
Removing the front push tractor
To remove the tractor from the front push position, follow
these steps:
1. Remove any paper from the tractor as described in the previous
section.
2. Turn off the printer.
3. Open the front paper guide by pulling the tab at the center of
the guide. Then remove the guide by grasping both sides and
pulling it straight out of the printer.
4. Press the tractor’s lock tabs, tilt the tractor up, and lift it out of
the printer.
5. Replace the front paper guide by sliding it along the printer’s
mounting slots until it locks in place. Then close the front
paper guide.
2-17nn
2-16b
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-16 Printing on Continuous Paper
Using the Rear Push Tractor
To use the rear push tractor, load continuous paper in the rear
slot. For information on when to use the rear push tractor, see
“Available Paper Paths” on page 3.
Loading paper onto the rear push tractor
If a tractor is installed in the pull position, you need to remove
it and replace the paper tension unit as described on page 2-33
before using the rear push tractor.
Note:
TTo avoid paper jams, it is best to load thick multi-part forms using
the front or bottom slot and pull or front push tractor.
TWhen loading multi-part forms that are bound on only one side by
point glueing, use the rear push tractor.
cCaution:
Do not load continuous paper with labels in the rear paper slot;
the labels may come off their backing sheet inside the printer and
cause a paper jam.
To load paper onto the rear push tractor, follow these steps:
1. Open the paper guide cover and remove the paper guide.
c
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-17
2. Set the paper release lever to the rear push tractor position.
Also set the paper thickness lever (located under the
printer cover) to the proper position for your paper’s
thickness.
3. Release the left and right sprockets by pulling the sprocket
lock levers forward.
2-26
front of the printer
2-27
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-18 Printing on Continuous Paper
4. Slide the left sprocket to the left margin of the paper using the
scale on the printer. (Printing starts at the “0” mark.) Then
push the lever back to lock it in place.
Note:
See “Paper alignment” and “Printable area” in Appendix C for more
information on the left margin position.
5. Slide the right sprocket to match the width of your paper, but
do not lock it. Move the paper support midway between the
two sprockets as shown above.
6. Open both sprocket covers. Make sure your paper has a
clean, straight edge and fit the first four holes of the paper,
printable side down, over the tractor pins. Then close the
sprocket covers.
7. Slide the right sprocket to remove any slack in the paper; then
lock it in place by pushing the sprocket lock down.
front of the printer
2-28
front of the printer
2-29
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-19
8. Attach the paper guide as described on page 1-11.
9. Slide the edge guides to the middle of the paper guide. Then
close the paper guide cover.
Note:
Always close the printer cover before printing. The printer does not
print when the cover is open.
10. Make sure the printer is on. You may need to check and
change the printer driver settings as described in Chapter 4.
When the printer receives data, it automatically loads the
paper and starts printing. The printed pages are fed over
the paper guide toward the back of the printer.
11. After you finish printing, follow the steps in the next section to
tear off your printed document.
If the first printed line on your page appears too high or low,
you can fix this by using the micro adjust feature as described
in “Adjusting the Top-of-Form Position” on page 2-37.
cCaution:
Never use the knob to adjust the top-of-form position; this may
damage the printer or cause it to lose the top-of-form position.
2-29a
2-35C
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-20 Printing on Continuous Paper
Removing the printed document from the rear push
tractor
To remove the printed document, follow these steps:
1. Make sure the Tear Off/Bin lights are flashing. (This indicates
your paper is at the current tear-off position). You may need to
press the Tear Off/Bin button to advance the paper to the
tear-off position.
2. Open the paper guide cover, and tear off the printed
document using the tear-off edge of the printer.
Note:
If your paper’s perforation is not properly aligned with the tear-off
edge, you can adjust the tear-off position using the micro adjust
feature. See “Adjusting the tear-off position” on page 2-41.
cCaution:
Never use the knob to adjust the tear off position; this may
damage the printer or cause it to lose the tear-off position.
3. Close the paper guide cover.
When you resume printing, the printer automatically feeds the
paper back to the top-of-form position and starts printing.
P3-9
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-21
To remove the remaining paper from the printer, press the
Load/Eject button to feed the paper backward to the standby
position. (See the Glossary for an explanation of the standby
position.) Then open the sprocket covers of the tractor and
remove paper.
cCaution:
Always tear off your printed document before you press the
Load/Eject button. Reverse feeding several pages at a time may
cause a paper jam.
Using the Tractor in the Pull Position
Using the tractor in the pull position is ideal for printing on
thick and heavy continuous paper, such as multi-part forms or
continuous paper with labels. However, you cannot use the
tear-off feature with the pull tractor.
You can also load paper onto the pull tractor from the rear slot.
However, doing so is not recommended because the paper
path from the rear slot is curved. Because thick paper requires
a straight paper path to avoid paper jams, it is best to load
paper in the front or bottom slot when using the pull tractor.
cCaution:
Do not load continuous paper with labels in the rear paper slot;
the labels may come off their backing sheet inside the printer and
cause a paper jam.
To further reduce the chance of paper jams and improve the
performance of continuous paper, you can use two tractors in
combination. When using this printing method, you load your
paper onto both the front push tractor and the pull tractor, or
both the rear push tractor and the pull tractor. See “Using two
tractors in a push and pull combination” on page 2-30.
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-22 Printing on Continuous Paper
Installing the tractor in the pull position
To install a tractor in the pull position you must either remove
the front push tractor or purchase the optional pull tractor
(C80032@). To remove the front push tractor, see “Removing
the front push tractor” on page 2-16.
Note:
The tractor in the rear push position cannot be removed.
To install a tractor in the pull position, follow these steps:
1. Make sure the printer is turned off. Lift the printer cover up and
off the printer.
2. Push up the tabs on each side of the paper tension unit and
lift the unit up and off the printer. Store the paper tension
unit in a safe place.
2-18NN
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-23
3. Lower the tractor into the printer’s mounting slots and press
down both ends of the tractor to make sure that it is firmly
seated.
You are now ready to load continuous paper onto the pull
tractor as described in the next section. To remove the pull
tractor, see page 2-33.
Loading paper onto the pull tractor
When using the pull tractor, load continuous paper in the front
or bottom slot, if possible; loading paper in the rear slot may
increase the chance of a paper jam.
cCaution:
TAlways load multi-part forms with seven parts (one
original plus six copies) using the front or bottom slot and
the pull tractor. Loading this type of form in the rear slot
may cause a paper jam.
TDo not load continuous paper with labels in the rear paper
slot; the labels may come off their backing sheet inside the
printer and cause a paper jam.
2-19nn
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-24 Printing on Continuous Paper
To load paper onto the pull tractor, follow these steps:
1. Make sure the printer is turned off, and the printer cover is
removed. Also check that a tractor is installed in the pull
position.
2. Slide the edge guides to the middle of the paper guide.
3. Set the paper release lever to the pull tractor position. Also
set the paper thickness lever to the proper position for your
paper’s thickness.
4. Release the left and right sprockets by pulling the sprocket
lock levers forward.
2-31
2-32a
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-25
5. Slide the left sprocket to the left margin of the paper using the
scale on the paper guide as a guide. (Printing starts at the
arrow mark.) Then push the lever back to lock it in place.
Note:
See “Paper alignment” and “Printable area” in Appendix C for more
information on the left margin position.
6. Push back the left sprocket lever to lock it in place.
7. Slide the right sprocket to match the width of your paper, but do
not lock it. Move the paper support midway between the two
sprocket units as shown above. Then open both sprocket
covers.
8. Make sure your paper has a clean, straight edge.
2-33a
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-26 Printing on Continuous Paper
9. Insert the paper into the front, bottom, or rear paper slot as
described below until it emerges between the platen and
the ribbon guide. Then pull up the paper until the
perforation between the first and second pages is even
with the top of the printer’s ribbon.
10. Fit four holes of the paper over the tractor pins on both
sprockets. Then close the sprocket covers.
11. Slide the right sprocket to remove any slack in the paper; then
lock it in place by pushing the sprocket lock down.
Before you load paper in the
front slot, remove the front
paper guide. Then load
paper printable side up.
2-34a
Load paper in the bottom slot
printable side up (forward).
2-34b
Before you load paper in the
rear slot, remove the paper
guide. Then load paper in
the rear slot printable side
down.
2-34c
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-27
12. If you use the front slot, attach the front paper guide with
the continuous paper positioned as shown below. Then
close it.
If you use the rear slot, replace the paper guide and make sure
the edge guides are together in the middle of the paper
guide.
13. Turn on the printer.
14. Remove any slack in the paper and adjust the top-of-form
position (the position where the printer will start printing) by
pressing the LF/FF button or using the micro adjust feature.
(To use the micro adjust feature, see “Adjusting the
Top-of-Form Position” on page 2-37.) The printer will start
printing at the current position without advancing the paper.
cCaution:
TNever use the knob to remove slack in the paper or to
adjust the top-of-form position; this may damage the
printer or cause it to lose the top-of-form position.
TAlways remove any slack from the paper; otherwise
print quality may be reduced.
G3-19-AA
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-28 Printing on Continuous Paper
15. Attach the printer cover and close the paper guide cover.
Note:
Always close the printer cover before printing. The printer does not
print when the cover is open.
16. You may need to check and change the printer driver
settings as described in Chapter 4. Send a print job to the
printer. The printer starts printing from the current
position without advancing the paper. The printed pages
are fed over the paper guide toward the back of the printer.
17. After you finish printing, open the paper guide cover; then
tear off the printed document at the perforation nearest the
paper exit slot.
2-35
new10
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-29
Removing paper from the pull tractor
1. After you finish printing, tear off the fresh supply of paper at
the perforation nearest the paper entry slot.
2. Hold down the LF/FF button to eject the paper from the printer.
cCaution:
Never press the Load/Eject button when using the pull tractor;
feeding the paper backward may cause it to come off the pull
tractor and jam the printer.
Using two tractors in a push and pull combination
To improve continuous paper feeding and reduce paper jams,
you can use two tractors at the same time. When using two
tractors in combination, you can load paper in the front paper
slot onto both the front push tractor and the pull tractor, or in
the rear paper slot onto both the rear push tractor and the pull
tractor.
G05-1
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-30 Printing on Continuous Paper
To use the front push tractor with the pull tractor, you need to
purchase the optional pull tractor (C80032@). The tractor in the
rear push position cannot be removed. Install the optional pull
tractor as described in “Installing the tractor in the pull
position” on page 2-23.
To use the rear push tractor with the pull tractor, you can
remove the tractor from the front push position as described on
page 2-16, and install it in the pull position as described on
page 2-23.
Note:
The tractor in the rear push position cannot be removed.
To load paper onto two tractors, follow these steps:
1. Remove the printer cover and paper guide.
2. Make sure one tractor is in the front or rear push position and
one tractor is in the pull position. Set the paper release lever to
either the front push or rear push tractor position, depending
on which push tractor you are using. Also, set the paper
thickness lever to the proper position for your paper’s
thickness.
3. Load paper onto the front or rear push tractor as described
earlier in this chapter.
4. Turn on the printer. Press the Load/Eject button to advance
the paper to the top-of-form position. Then press the LF/FF
button until the perforation between the first and second
pages is even with the top of the printer’s ribbon.
cCaution:
Never use the knob to move the paper; this may damage the
printer or cause it to lose the top-of-form position.
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-31
5. Attach the paper to the pull tractor’s sprockets as described in
“Loading paper onto the pull tractor” on page 2-24.
6. Set the paper release lever to the pull tractor position. Then
remove any slack in the paper between the push and pull
tractors using the micro adjust feature (described on page
2-37) if necessary.
7. Move the paper release lever back to the push tractor position
you set in step 2.
8. Adjust the top-of-form position (the position where the printer
will start printing) using the micro adjust feature as described
in “Adjusting the Top-of-Form Position” on page 2-37. The
printer will start printing at the current position without
advancing the paper.
cCaution
TNever use the knob to remove slack in the paper or to
adjust the top-of-form position; this may damage the
printer or cause it to lose the top-of-form position.
TAlways remove any slack from the paper; otherwise
print quality may be reduced.
9. Attach the paper guide. Then slide the edge guides to the
middle of the paper guide.
10. Attach the printer cover and close the paper guide cover.
Note:
Always close the printer cover before printing. The printer does not
print when the cover is open.
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-32 Printing on Continuous Paper
11. You may need to check and change the printer driver
settings as described in Chapter 4. Send a print job to the
printer. The printer starts printing from the current
position without advancing the paper. The printed pages
are fed over the paper guide toward the back of the printer.
12. After you finish printing, open the paper guide cover; then tear
off the printed document at the perforation nearest the paper
exit slot.
To remove the paper from the tractors, follow the steps under
“Removing paper from the pull tractor” on page 2-30.
Removing the pull tractor
To remove the tractor from the pull position, follow these steps:
1. Remove any paper loaded on the pull tractor as described on
page 2-30.
2. Turn off the printer. Then remove the printer cover and lift the
paper guide up and off the printer.
2-35AC
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-33
3. Press the tractor’s lock tabs, tilt the tractor toward you, and
lift it off the printer.
4. Store the tractor in a safe place, or install it in the front push
position as described on page 2-9.
5. To replace the paper tension unit, lower it onto the printer’s
mounting pegs. Then press down both ends of the unit
until it clicks into place.
6. Replace the paper guide and printer cover. Then close the paper
guide cover.
g3-17-3
g1-9-1
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-34 Printing on Continuous Paper
Switching Between Printing on Continuous Paper
and Printing on Single Sheets
You can easily switch back and forth between printing on
continuous paper with a push tractor and printing on single
sheets without having to remove or reload paper.
Switching to printing on single sheets
To switch from printing on continuous paper with the front or
rear push tractor to printing on single sheets, follow these steps.
Note:
RIf continuous paper with labels is loaded in the printer, remove it
before switching to single-sheet printing. See “Removing
continuous paper with labels” on page 2-8.
RIf a tractor is in the pull position, remove any continuous paper
from it before switching to single-sheet printing. See “Removing
paper from the pull tractor” on page 2-30.
1. If any printed pages of continuous paper remain in the printer,
press the Tear Off/Bin button to advance printed pages to the
tear-off position, and then tear them off.
cCaution:
TTear off your printed document before you press the
Load/Eject button in the next step. Reverse feeding
several pages at a time may cause a paper jam.
TNever use the knob to eject paper while the printer is
on; this may damage the printer or cause it to lose the
tear-off position.
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-35
2. Press the Load/Eject button to feed the continuous paper
backward to the standby position. The paper is still attached to
the push tractor but is no longer in the paper path.
3. Load single sheets in the top or front paper guide as described
in Chapter 3.
Switching to printing on continuous paper
To switch from printing on single sheets to printing on
continuous paper with the front or rear push tractor, follow
these steps:
1. If a single sheet remains in the printer, press the Load/Eject
button to eject it.
cCaution:
Never use the knob to eject paper while the printer is on; this
may damage the printer or cause it to lose the top-of-form
position.
2. Make sure that the tractor is installed in the front or rear push
position which you plan to use. To install the tractor in the
front position, see page 2-9.
3. Load continuous paper onto the front or rear push tractor as
described earlier in this chapter.
The printer loads your continuous paper automatically when
you begin printing.
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-36 Printing on Continuous Paper
Adjusting the Top-of-Form Position
The top-of-form position is the position on the page where the
printer will start printing. If your printing appears too high or
low on the page, you can use the micro adjust feature to adjust
the top-of-form position as described below.
cCaution:
Never use the knob to adjust the top-of-form position; this may
damage the printer or cause it to lose the top-of-form position.
Note:
RYour top-of-form position setting remains in effect until you
change it, even if you turn off the printer.
RThe top margin setting made in some application software
overrides the top-of-form position setting you make with the
micro adjust feature. If necessary, adjust the top-of-form position
using your software.
1. Make sure the printer is turned on.
2. If necessary, load paper as described earlier in this chapter. If
you load paper onto a push tractor, press the Load/Eject
button to advance the paper to the current top-of-form
position.
3. Lift the printer cover up and off the printer.
4. Hold down the Pause button for about three seconds. The Pause
light starts flashing and the printer enters the micro adjust
mode.
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-37
5. Press the LF/FF
D button to move the top-of-form position up
on the page, or press the Load/Eject
U button to move the
top-of-form position down on the page.
cCaution:
Never use the knob to adjust the top-of-form position; this
may damage the printer or cause it to lose the top-of-form
position.
Note:
RThe printer has a minimum and a maximum top-of-form
position. If you try to adjust it beyond these limits, the
printer beeps and stops moving the paper.
RWhen the paper reaches the default top-of-form position,
the printer also beeps and stops moving the paper briefly.
You can use the default setting as a reference point when
adjusting the top-of-form position.
plastic ribbon
cover 3-6anew
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-38 Printing on Continuous Paper
To adjust the top-of-form position for continuous paper
loaded on the pull tractor, see the following example:
First mark a point 6.5 mm (0.26 inch) above the paper’s
perforation; then position the paper so that the mark even
with the top edge of the plastic ribbon cover. This gives you an
8.5 mm (0.33 inch) margin on the next page, meaning the
printer starts printing 8.5 mm below the perforation. If you
mark a point 5.5 mm (0.22 inch) above the perforation, you get
a 9.5 mm (0.37 inch) margin on the next page.
6. After you set the top-of-form position, press the Pause button
to exit micro adjust mode.
(0.26 inch)
(0.33 inch)
new14
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-39
Advancing the Paper to the Tear-Off Edge
If you use the front or rear push tractor, you can use the tear-off
feature to advance your continuous paper to the printer’s
tear-off edge when you finish printing. You can then easily tear
off the printed document. When you resume printing, the
printer automatically feeds the paper back to the top-of-form
position so that you can save the paper normally lost between
documents.
As described below, you can use the tear-off feature in two
ways: manually by pressing the printer’s Tear Off/Bin button,
or automatically by turning on the auto tear-off mode.
If the perforation between pages is not aligned with the tear-off
edge, you can adjust the position of the perforation using the
micro adjust feature. See “Adjusting the tear-off position” on
page 2-41 for instructions.
cCaution:
Never use the tear-off feature (by pressing the Tear Off/Bin
button or turning on the auto tear-off mode as described below) to
feed continuous paper with labels backward; they may come off
their backing sheet and jam the printer.
Using the Tear Off/Bin button
After the printer finishes printing your document, check that
the Tear Off/Bin lights are not flashing. Then press the Tear
Off/Bin button. The printer advances the paper to the tear-off
edge.
Note:
If the Tear Off/Bin lights are flashing, the paper is in the tear off position.
If you press the Tear Off/Bin button, the printer feeds your paper to the
next top-of-form position.
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-40 Printing on Continuous Paper
Advancing paper to the tear-off position automatically
To automatically advance your printed documents to the
tear-off position, you need to turn on the auto tear-off mode
and select the appropriate page length for continuous paper in
the default-setting mode. For instructions, see “About Your
Printer’s Default Settings” on page 5-3.
When auto tear-off is on, the printer automatically advances
the paper to the tear-off position whenever it receives a full
page of data or a form feed command followed by no more
data.
Adjusting the tear-off position
If your paper’s perforation is not aligned with the tear-off edge,
you can use the micro adjust feature to move the perforation to
the tear-off position. Follow the steps below.
cCaution:
Never use the knob to adjust the tear-off position; this may
damage the printer or cause it to lose the tear-off position.
Note:
Your tear-off position setting remains in effect until you change it, even if
you turn off the printer.
1. Make sure the Tear Off/Bin lights are flashing (the paper is at
the current tear-off position). You may need to press the Tear
Off/Bin button to advance the paper to the tear-off position.
2. Open the paper guide cover.
3. Hold down the Pause button for about three seconds. The Pause
light begins flashing and the printer enters the micro adjust
mode.
2
R
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
Printing on Continuous Paper 2-41
4. Press the LF/FF
D button to feed the paper backward, or press
the Load/Eject
U button to feed the paper forward, until
the paper perforation is aligned with the tear-off edge.
Note:
The printer has a minimum and a maximum tear-off position. If you
try to adjust the tear-off position beyond these limits, the printer
beeps and stops moving the paper.
5. After you set the tear-off position, press the Pause button to
turn off micro adjust mode.
6. Tear off the printed pages.
When you resume printing, the printer automatically feeds the
paper back to the top-of-form position and begins printing.
tear-off edge
3-6BNEW
L
Sun-G+ Rev.C
A5 size Chapter 2
97/11/17 pass 3
2-42 Printing on Continuous Paper
Chapter 3
Printing on Single Sheets
Proof Sign-off:
Yamanouchi _______
Grady _______
Using Single Sheets . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Available paper types and paper slots . . . . . . . . . . . . . . . 3-2
Loading single-sheet multi-part forms . . . . . . . . . . . . . . . 3-4
Loading envelopes . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Loading postcards . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Loading Single Sheets in the Top Paper Slot . . . . . . . . . . . 3-8
Loading Single Sheets in the Front Paper Slot . . . . . . . . . . 3-10
3
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
Printing on Single Sheets 3-1
Using Single Sheets
Available paper types and paper slots
As shown below, you can load single-sheet paper one sheet at
a time using the paper guide on top of the printer or the front
paper guide. You can print on ordinary single sheets,
single-sheet multi-part forms, postcards, and envelopes. Your
single-sheet paper may be from 101 to 420 mm (4.0 to 16.5
inches) wide.
Note:
TTo load a stack of single-sheet paper, use the optional cut-sheet
feeder. See Appendix A, “Enhancing Your Printer With Options.”
TFor detailed specifications on the types of single-sheet paper you
can use, see Appendix C.
top paper slot
2-9N
front paper slot
2-12
L
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
3-2 Printing on Single Sheets
The table below shows the types of paper you can load in the
top and front paper slots and the paper thickness lever settings
for each paper type. For more information on the paper
thickness lever, see page 2-3.
Paper type Available
paper slots Paper thickness
lever position
Ordinary single-sheet paper Top and front -1 or 0
Multi-part forms (carbonless)
2 parts (original + 1 copy)
3 parts (original + 2 copies)
4 parts (original + 3 copies)
5 parts (original + 4 copies)
6 parts (original + 5 copies)
Top and front
1
3
4
5
6
Postcards Top and front 3
Envelopes Top 4 or 5
Note:
RIf the printed image is smeared, you may need to set the paper
thickness lever one position lower to improve print quality.
RIf the printed image is faint or has many gaps, you may need to
set the paper thickness lever one position higher to improve print
quality.
RDo not load paper that is damaged, curled or has been folded.
3
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
Printing on Single Sheets 3-3
Loading single-sheet multi-part forms
You can load single-sheet multi-part forms one at a time in the
top or front paper slot as described in “Loading Single Sheets
in the Top Paper Slot” or “Loading Single Sheets in the Front
Paper Slot,” later in this chapter. Also, follow these guidelines:
TUse only carbonless multi-part forms bound as shown
below.
TYou can use the top or front paper slot to load single-sheet
multi-part forms that are bound at the top.
Insert this type of form in the top slot with the bound edge first
and the printable side down, as shown below.
bound only at the top
by line glueing
bound only at the side
by line glueing New04, 06
printable side down
new03
L
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
3-4 Printing on Single Sheets
Insert this type of form in the front slot with the bound edge first
and the printable side up, as shown below.
TYou can load multi-part forms bound at the side only in the
front slot. Insert this type of form in the front slot with the
top edge first and the printable side up, as shown below.
TBefore printing, set the paper thickness lever (located under
the printer cover) to the proper position for your paper. See
the table on page 3-3.
TBe sure your multi-part forms do not exceed 0.46 mm
(0.018 inch) in thickness.
TUse multi-part forms only under normal temperature and
humidity conditions, as follows:
Temperature 15 to 25°C (59 to 77°F)
Humidity 30 to 60% RH
printable side up
new05
printable side up
NEW07
3
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
Printing on Single Sheets 3-5
Loading envelopes
You can load envelopes only in the top paper slot as described
in “Loading Single Sheets in the Top Paper Slot” on page 3-8.
Also, follow these guidelines:
TLoad envelopes one at a time in the top slot, with the flap
edge first and the flap side up.
TSet the paper thickness lever (located under the printer
cover) to position 4 or 5.
TBefore printing, turn on the card mode by pressing the
Tear Off/Bin button until both Tear Off/Bin lights are on.
After you finish printing on envelopes, press the Tear
Off/Bin button once to exit the card mode. (Bin 1 is
selected.)
TDo not use envelopes that are curled or folded. Also avoid
using envelopes that are too thin; they may curl during
printing and become jammed.
TIf you use No. 6 envelopes, align the left edge of the
envelope with the arrow mark on the printer.
TUse envelopes only under normal temperature and
humidity conditions, as follows:
Temperature 15 to 25°C (59 to 77°F)
Humidity 30 to 60% RH
flap side up,
printable side down new01
L
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
3-6 Printing on Single Sheets
cCaution:
Because printing on the edge of an envelope may damage the print
head, make sure the printing stays entirely within the printable
area of your envelopes. See Appendix C for details on the printable
area of envelopes.
Loading postcards
You can load postcards one at a time in the top or front paper
slot as described in “Loading Single Sheets in the Top Paper
Slot” or “Loading Single Sheets in the Front Paper Slot,” later in
this chapter. Also, follow these guidelines:
TIf you load postcards long edge first, always load them in
the top slot.
TSet the paper thickness lever (located under the printer
cover) to position 3.
TBefore printing, turn on the card mode by pressing the
Tear Off/Bin button until both Tear Off/Bin lights are on.
After you finish printing on postcards, press the Tear
Off/Bin button once to exit the card mode. (Bin 1 is
selected.)
TUse postcards only under normal temperature and
humidity conditions, as follows:
Temperature 15 to 25°C (59 to 77°F)
Humidity 30 to 60% RH
new11
3
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
Printing on Single Sheets 3-7
Loading Single Sheets in the Top Paper Slot
To load paper in the top slot, follow these steps:
1. Make sure the paper guide is installed properly. If not, attach it
as described on page 1-11.
2. Open the paper guide cover. Slide the left edge guide until
it locks in place next to the arrow on the paper guide. Next
adjust the right edge guide to match the width of your
paper.
3. Set the paper release lever to the single-sheet position. Also
set the paper thickness lever (located under the printer
cover) to the proper position for your paper’s thickness .
(See the table on page 3-3.)
2-7n
2-6
L
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
3-8 Printing on Single Sheets
4. Close the paper guide cover.
5. Press the Operate button to turn on the printer, if necessary.
6. Insert a sheet of paper printable side down between the edge
guides until it meets resistance. The printer feeds the paper
automatically and is ready to print.
Note:
Always close the printer cover before printing. The printer does not
print when the cover is open.
2-8n
2-9n
3
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
Printing on Single Sheets 3-9
7. Check and change the printer driver settings as described in
Chapter 4. Then send a print job to the printer.
When the printer receives data, it prints the page and ejects it
back onto the paper guide. To continue printing your
document, remove the printed page and insert a new sheet of
paper. If you need to eject a sheet, press the Load/Eject button.
If the first printed line on your page appears too high or low,
you can fix this using the micro adjust feature. See “Adjusting
the Top-of-Form Position” on page 2-37.
cCaution:
Never use the knob to adjust the top-of-form position or eject a
sheet when the printer is on; this may damage the printer or cause
it to lose the top-of-form position.
Loading Single Sheets in the Front Paper Slot
To load paper in the front paper slot, follow these steps:
1. Make sure the paper guide is installed properly. If not, attach it
as described on page 1-11.
2. Make sure the paper guide cover is closed.
L
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
3-10 Printing on Single Sheets
3. Open the front paper guide by pulling the tab at the center
of the guide. Slide the left edge guide as shown below.
(Printing starts at the arrow mark.) Next adjust the right
edge guide to match the width of your paper.
4. Set the paper release lever to the single-sheet position. Also set
the paper thickness lever (located under the printer cover) to
the proper position for your paper’s thickness. (See the table
on page 3-3.)
5. Press the Operate button to turn on the printer, if necessary.
2-11nn
2-10a
3
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
Printing on Single Sheets 3-11
6. Insert a sheet of paper printable side up between the edge
guides until it meets resistance. The printer feeds the paper
automatically and is ready to print.
Note:
Always close the printer cover before printing. The printer does not
print when the cover is open.
7. You may need to check and change the printer driver settings as
described in Chapter 4. Then send a print job to the printer.
When the printer receives data, it prints the page and ejects it
onto the paper guide on top of the printer. To continue printing
your document, remove the printed page and insert a new
sheet of paper in the front paper guide. If you need to eject a
sheet, press the Load/Eject button.
If the first printed line on your page appears too high or low,
you can fix this using the micro adjust feature. See “Adjusting
the Top-of-Form Position” on page 2-37.
cCaution:
Never use the knob to adjust the top-of-form position or eject a
sheet when the printer is on; this may damage the printer or cause
it to lose the top-of-form position.
2-12
L
Sun-G+ Rev.C
A5 size Chapter 3
97/11/14 pass 1
3-12 Printing on Single Sheets
Chapter 4
Using the Printer Software
Proof Sign-off:
Yamanouchi _______
Grady _______
About Your Printer Software . . . . . . . . . . . . . . . . . . . 4-2
Using the Printer Driver With Windows 95 . . . . . . . . . . . 4-3
Accessing the printer driver from Windows applications . . . . 4-3
Accessing the printer driver from the Start menu . . . . . . . . . 4-5
Printer driver settings overview . . . . . . . . . . . . . . . . . . 4-5
Using the Printer Driver With Windows 3.1 . . . . . . . . . . . 4-8
Accessing the printer driver from Windows applications . . . . 4-8
Accessing the printer driver from the Control Panel . . . . . . . 4-10
Printer driver settings overview . . . . . . . . . . . . . . . . . . 4-10
Using the Printer Driver With Windows NT 4.0 . . . . . . . . 4-12
Accessing the printer driver from Windows applications . . . . 4-12
Accessing the printer driver from the Start menu . . . . . . . . . 4-14
Printer driver settings overview . . . . . . . . . . . . . . . . . . 4-14
Using the Printer Driver With Windows NT 3.5x . . . . . . . . 4-17
Accessing the printer driver from Windows applications . . . . 4-17
Accessing the printer driver from the Control Panel . . . . . . . 4-19
Printer driver settings overview . . . . . . . . . . . . . . . . . . 4-19
Using the EPSON Remote! Utility . . . . . . . . . . . . . . . . . 4-21
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-1
About Your Printer Software
The EPSON printer software that comes with your printer
includes the printer driver software, the EPSON Remote!
utility, and the EPSON Status Monitor 2 utility for Windows 95.
As described in Chapter 1, a printer driver is software that
allows your computer to control the printer. You need to install
the printer driver so your Windows software applications can
take full advantage of the printer’s capabilities.
Note:
Before proceeding, make sure you have installed the printer driver on
your PC as described in Chapter 1.
EPSON Remote! is a DOS-based printer setup utility that
allows you to easily change the printer’s default settings from
the computer screen. To use the EPSON Remote! utility with
DOS, see page 4-21.
The EPSON Status Monitor 2 utility program is available only
for Windows 95. It monitors the status of your printer, alerts
you when errors occur, and provides you with troubleshooting
tips. To install and use the Status Monitor, see Chapter 6,
“Using EPSON Status Monitor 2.”
To use the printer driver, see the appropriate page below,
depending on your Windows version.
Windows 95 . . . . . . . . . . . . . . . . 4-3
Wndows 3.1 . . . . . . . . . . . . . . . . 4-8
Windows NT 4.0 . . . . . . . . . . . . . 4-12
Windows NT 3.5x . . . . . . . . . . . . . 4-17
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-2 Using the Printer Software
Using the Printer Driver With Windows 95
While many Windows applications override the settings made
with the printer driver, some do not, so you must verify that
the printer driver settings match your requirements. To access
the printer driver, see “Accessing the printer driver from
Windows applications” or “Accessing the printer driver from
the Start menu,” below. To check and change the printer driver
settings, see “Printer driver settings overview” on page 4-5.
Accessing the printer driver from Windows applications
When you access the printer driver from a Windows
application, any settings you make apply only to the
application you are using. To access the printer driver from
a Windows application, follow the steps below.
Note:
The steps below provide general guidelines on accessing the printer
driver. How you access the printer driver may differ depending on your
application. See your application manual for details.
1. Select Print Setup or Print from the File menu of your
application software. The Print or Print Setup dialog box
appears.
95D
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-3
2. Make sure that your printer is selected and then click Printer,
Setup, Properties, or Options. (You may need to click a
combination of these buttons.) The Properties window
appears, and you see the Paper, Graphics, and Device
Options menus. These menus contain the printer driver
settings.
3. To view a menu, click the corresponding tab at the top of the
window. See “Printer driver settings overview” on the next
page for detailed information about the settings.
95
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-4 Using the Printer Software
Accessing the printer driver from the Start menu
When you access the printer driver from the Start menu, the
printer driver settings you make apply to all your applications.
To access the printer driver from the Start menu, follow these
steps:
1. Click the Start button, and then point to Settings.
2. Click Printers.
3. Right-click your printer icon, and click Properties. The screen
displays the Properties window, which contains the Paper,
Graphics, and Device Options menus. These menus provide
the printer driver settings.
4. To view a menu, click the corresponding tab at the top of the
window. See the next section for detailed information about
the printer driver settings.
Printer driver settings overview
Your printer driver has three menus: the Paper, Graphics, and
Device Options menus. The printer driver settings on each of
these menus are described below. To open these menus, see the
previous sections on accessing the printer driver.
When you finish making your printer driver settings, click OK
to apply the settings, or click Restore Defaults to return the
settings to their previous values.
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-5
Paper menu
TPaper size Select the size of the paper you want
to use. If you don’t see your paper size,
use the scroll bar to scroll through the
list. If your paper size is not included
in the list, click Custom and enter the
paper size in the dialog box that
appears.
TOrientation Select Portrait or Landscape.
TPaper source Click the paper source you want to use.
95paper1
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-6 Using the Printer Software
Graphics menu
TResolution Click the printing resolution you want.
The higher the resolution you select,
the more detailed your printout will
be; however, increasing the resolution
slows printing.
TDithering You can leave this option set to Fine,
which is the default setting, or select
another dithering pattern depending
on the kind of printout you want. The
display to the left of the dithering
options shows the effect of your
setting.
TIntensity Move the slider to make your printout
lighter or darker.
95GRAPHI
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-7
Device Options menu
TPrint quality Select a print quality option from the
Print quality list. Selecting a high
quality option produces more detailed
printouts at a slower printing speed.
Once you’ve checked your printer driver settings and changed
them if necessary, you are ready to print with continuous
paper as described in Chapter 2, or with single sheets as
described in Chapter 3.
Using the Printer Driver With Windows 3.1
While many Windows applications override the settings made
with the printer driver, some do not, so you must verify that
the printer driver settings match your requirements. To access
the printer driver, see “Accessing the printer driver from
Windows applications” or “Accessing the printer driver from
the Control Panel,” below. To check and change the printer
driver settings, see “Printer driver settings overview” on page
4-10.
Accessing the printer driver from Windows applications
When you access the printer driver from a Windows
application, any settings you make apply only to the
application you are using. To access the printer driver from a
Windows application, follow the steps on the next page.
95DEVICE
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-8 Using the Printer Software
Note:
The steps below provide general guidelines on accessing the printer
driver. How you access the printer driver may differ depending on your
application. See your application manual for details.
1. Select Print Setup or Print from the File menu of your application
software. The Print or Print Setup dialog box appears. See
“Printer driver settings overview” on the next page for
detailed information about the settings in this dialog box.
2. Make sure that your printer is selected and then click Printer,
Setup, or Options. (You may need to click a combination
of these buttons.) The Options dialog box appears. See page
4-11 for detailed information about the settings in this
dialog box.
PRINT
OPTIONS
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-9
Accessing the printer driver from the Control Panel
When you access the printer driver from the Control Panel, the
printer driver settings you make apply to all your applications.
To access the printer driver from the Control Panel, follow
these steps:
1. In the Main window, double-click the Control Panel icon.
2. Double-click the Printers icon. The Printers dialog box appears.
3. Make sure your printer is highlighted, then click Setup. The
Print Setup dialog box appears. To access more settings, you
may need to click Options. See the next section for detailed
information about the printer driver settings.
Printer driver settings overview
The printer driver settings are described below. To access the
printer driver settings, see the previous sections on accessing
the printer driver.
When you finish making your printer driver settings, click OK
to apply the settings, or click Cancel to cancel your changes.
Print or Print Setup dialog box
TResolution Click the printing resolution you
want. The higher the resolution you
select, the more detailed your printout
will be; however, increasing the
resolution slows printing. This setting
is available only from the Control
Panel.
TOrientation Select Portrait or Landscape. The
diagram on the screen changes
depending on the orientation you
select.
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-10 Using the Printer Software
TPaper Size Select the size of the paper you want
to use. If you don’t see your paper
size, use the scroll bar to scroll
through the list. If your paper size is
not included in the list, click User
Defined Size and enter the paper size
in the dialog box that appears.
TPaper Source Click the paper source you want to
use.
Options dialog box
TDithering You can leave this option set to Fine,
which is the default setting, or select
another dithering pattern depending
on the kind of printout you want.
TIntensity Control Move the slider to make your printout
lighter or darker.
TPrint Quality Select a print quality option from the
Print Quality list. Selecting a high
quality option produces more detailed
printouts at a slower printing speed.
Once you’ve checked your printer driver settings and changed
them if necessary, you are ready to print with continuous
paper as described in Chapter 2, or with single sheets as described
in Chapter 3.
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-11
Using the Printer Driver With Windows NT 4.0
While many Windows applications override the settings made
with the printer driver, some do not, so you must verify that
the printer driver settings match your requirements. To access
the printer driver, see “Accessing the printer driver from
Windows applications” or “Accessing the printer driver from
the Start menu,” below. To check and change the printer driver
settings, see “Printer driver settings overview” on page 4-14.
Accessing the printer driver from Windows applications
When you access the printer driver from a Windows
application, any settings you make apply only to the
application you are using. To access the printer driver from
a Windows application, follow the steps below.
Note:
The steps below provide general guidelines on accessing the printer
driver. How you access the printer driver may differ depending on your
application. See your application manual for details.
1. Select Print Setup or Print from the File menu of your
application software. The Print or Print Setup dialog box
appears.
95D
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-12 Using the Printer Software
2. Make sure that your printer is selected and then click Printer,
Setup, Properties, or Options. (You may need to click a
combination of these buttons.) The Document Properties
window appears, and you see the Page Setup and
Advanced menus. These menus contain the printer driver
settings.
3. To view a menu, click the corresponding tab at the top of the
window. See “Printer driver settings overview” on the next
page for detailed information about the settings.
NT40PR
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-13
Accessing the printer driver from the Start menu
When you access the printer driver from the Start menu, the
printer driver settings you make apply to all your applications.
To access the printer driver from the Start menu, follow these
steps:
1. Click the Start button, and then point to Settings.
2. Click Printers.
3. Right-click your printer icon, and click Document Defaults.
The screen displays the Default Document Properties window,
which contains the Page Setup and Advanced menus. These
menus provide the printer driver settings.
4. To view a menu, click the corresponding tab at the top of the
window. See the next section for detailed information about
the printer driver settings.
Printer driver settings overview
Your printer driver has two menus: Page Setup and Advanced.
The printer driver settings on each of these menus are
described below. To open these menus, see the previous
sections on accessing the printer driver.
When you finish making your printer driver settings, click OK
to apply the settings, or click Cancel to cancel your changes.
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-14 Using the Printer Software
Page Setup menu
TPaper Size Select the size of the paper you want
to use from the Paper Size list.
TPaper Source Select the paper source you want to
use from the Paper Source list.
TOrientation Select Portrait or Landscape.
Advanced menu
NT40PR2
NT40AD
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-15
TPaper/Output Check the Paper Size, Orientation,
and Paper Source settings you made
on the Page Setup menu and change
them if necessary. Select the setting
and then choose an option from the
Change Setting list box.
TGraphic Select Resolution and then choose the
printing resolution from the Change
Setting list box. The higher the
resolution you select, the more
detailed your printout will be;
however, increasing the resolution
slows printing.
TDocument
Options Double-click Halftone Color
Adjustment to open the Halftone
Color Adjustment dialog box. Click
Print Quality to select a print quality
option. Click Print Text as Graphics or
Metafile Spooling and select On or
Off in the Change Setting list box.
Once you’ve checked your printer driver settings and changed
them if necessary, you are ready to print with continuous
paper as described in Chapter 2, or with single sheets as
described in Chapter 3.
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-16 Using the Printer Software
Using the Printer Driver With Windows NT 3.5x
While many Windows applications override the settings made
with the printer driver, some do not, so you must verify that
the printer driver settings match your requirements. To access
the printer driver, see “Accessing the printer driver from
Windows applications” or “Accessing the printer driver from
the Control Panel,” below. To check and change the printer
driver settings, see “Printer driver settings overview” on page
4-19.
Accessing the printer driver from Windows applications
When you access the printer driver from a Windows
application, any settings you make apply only to the
application you are using. To access the printer driver from
a Windows application, follow the steps below.
Note:
The steps below provide general guidelines on accessing the printer
driver. How you access the printer driver may differ depending on your
application. See your application manual for details.
1. Select Print Setup or Print from the File menu of your
application software. The Print or Print Setup dialog box
appears.
PRINT35
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-17
2. Make sure that your printer is selected and then click Printer,
Setup, Properties, or Options. (You may need to click a
combination of these buttons.) The screen displays the
Document Properties dialog box, which contains the Form
and Orientation printer driver settings. See “Printer driver
settings overview” on the next page for detailed
information about these settings.
3. Click Options (or a similar button) to view the Advanced
Document Properties dialog box, which includes the Graphics
Resolution, Color, and Optimizations printer driver settings.
See page 4-20 for detailed information about these settings.
DOC35
Advan35
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-18 Using the Printer Software
Accessing the printer driver from the Control Panel
When you access the printer driver from the Control Panel, the
printer driver settings you make apply to all your applications.
To access the printer driver from the Control Panel, follow
these steps:
1. In the Main window, double-click the Print Manager icon.
The Print Manager window opens.
2. Make sure your printer is highlighted, then click Printer and
select Properties. The Printer Properties dialog box appears.
3. Click the Details button, then click Job Default. You see the
Document Properties dialog box, which includes the Form and
Orientation printer driver settings. See the next section for
detailed information about these settings.
4. Click Options to open the Advanced Document Properties
dialog box, which contains the Graphics Resolution, Color,
and Optimization printer driver settings. See the next section
for detailed information about these settings.
Printer driver settings overview
Your printer driver has two dialog boxes: Document Properties
and Advanced Document Properties. The printer driver
settings in each of these dialog boxes are described below. To
open these dialog boxes, see the previous sections on accessing
the printer driver.
When you finish making your printer driver settings, click OK
to apply the settings, or click Cancel to cancel your changes.
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-19
Document Properties dialog box
TForm Select the type of paper you want to
use. If you don’t see your paper type,
select it from the Form list.
TOrientation Select Portrait or Landscape. The
diagram on the screen changes
depending on the orientation you
select.
Click the Halftone button to set the brightness and contrast,
input the RGB gamma, or make other settings. The Halftone
Color Adjustment dialog box appears. For details, click Help in
this dialog box.
Advanced Document Properties dialog box
TGraphics
Resolution Select a printing resolution option
from the Graphics Resolution list.
The higher the resolution you select,
the more detailed your printout will
be; however, increasing the resolution
slows printing.
TColor Only monochrome printing is available.
TOptimizations Click a check box to turn the
corresponding option on or off.
TPrint Quality To select the print quality, click the
More Options button. The More
Options dialog box appears. Selecting
a high quality option produces more
detailed printouts at a slower printing
speed.
Once you’ve checked your printer driver settings and changed
them if necessary, you are ready to print with continuous
paper as described in Chapter 2, or with single sheets as
described in Chapter 3.
L
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
4-20 Using the Printer Software
Using the EPSON Remote! Utility
The EPSON Remote! utility allows you to easily change the
printer’s default settings from your computer’s DOS prompt.
Installing EPSON Remote!
Follow the steps below to install EPSON Remote!.
1. Insert Disk 1 of your printer driver software in a disk drive.
2. At the DOS prompt, type A:\SETUP. (If you inserted the disk
in a drive other than drive A, substitute the appropriate letter.)
Then press Enter.
3. Select your printer’s name in the Printer Model window and
press Enter. C:\EPUTIL appears as the default directory.
4. Press Enter again. The EPSON Remote! utility is copied to the
C:\EPUTIL directory.
Accessing EPSON Remote!
To access EPSON Remote!, type C:\PRNSET at the DOS prompt
and press Enter. Then follow the on-screen instructions to use
this utility. You can also access EPSON Remote! by typing
C:\PANEL at the DOS prompt and press Enter. The PRNSET
and PANEL access methods differ slightly in that the PANEL
method opens a condensed version of EPSON Remote! that
only provides the most often used settings.
4
R
Sun-G+ Rev.C
A5 size Chapter 4
11/13/97 pass 0
Using the Printer Software 4-21
Chapter 5
Changing Printer Settings From the
Printer’s Control Panel
Proof Sign-off:
Yamanouchi _______
Grady _______
Selecting a Built-In Font and Pitch . . . . . . . . . . . . . . . . 5-2
About Your Printer’s Default Settings . . . . . . . . . . . . . . 5-3
Changing default settings . . . . . . . . . . . . . . . . . . . . . . 5-8
5
R
Sun-G+ Rev.C
A5 size Chapter 5
97/11/13 pass 0
Changing Printer Settings From the Printer’s Control Panel 5-1
Selecting a Built-In Font and Pitch
Your printer comes with the three built-in fonts shown in the
table below. You can also choose from the following six pitch
(character size) settings: 10, 12, 15, 17, or 20 cpi (characters per
inch), or proportional spacing. You can select the font and pitch
using the buttons on the printer’s control panel as described
below.
Note:
Settings you make in your application programs usually override settings
you make from the printer’s control panel. For best results, use your
application to select a font and pitch.
Font Sample
Draft
Roman
Sans Serif
Follow these steps to select a built-in font or pitch using the
buttons on the printer’s control panel:
1. Make sure that the printer is not printing. If it is, press the
Pause button to stop printing.
2. To select a font, press the Font button until the two Font lights
indicate the font you want as shown below.
Font lights Font
o n Draft
n o Roman
n n Sans Serif
n = On,
o = Off
L
Sun-G+ Rev.C
A5 size Chapter 5
97/11/13 pass 0
5-2 Changing Printer Settings From the Printer’s Control Panel
To select a pitch, press the Pitch button until the three
Pitch lights indicate the pitch you want as shown below.
Pitch lights Pitch
o o n 10 cpi
o n o 12 cpi
o n n 15 cpi
n o o 17 cpi
n o n 20 cpi
n n o PS
(proportional spacing)
n = On,
o = Off
About Your Printer’s Default Settings
The printer’s default settings control many printer functions.
While you can often set these functions through your software
or printer driver, you may sometimes need to change a default
setting from the printer’s control panel using the default-setting
mode.
The following table lists the default settings and the options
you can select in the default-setting mode. The settings are
explained in detail after the table. For instructions on changing
the default settings, see page 5-8.
5
R
Sun-G+ Rev.C
A5 size Chapter 5
97/11/13 pass 0
Changing Printer Settings From the Printer’s Control Panel 5-3
Settings Options
Page length for front tractor* Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8,
8.5, 11, 70/6, 12, 14, 17 inches
Page length for rear tractor* Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8,
8.5, 11, 70/6, 12, 14, 17 inches
Skip over perforation On, Off
Auto tear off On, Off
Auto line feed On, Off
Print direction Bi-D, Uni-D
I/F mode Auto, Parallel, Optional
Auto I/F wait time 10 seconds, 30 seconds
Software ESC/P, IBM 2381 Plus
Character table Standard model:
Italic, PC 437, PC 850, PC 860, PC 863,
PC 865, PC 861, BRASCII, Abicomp,
ISO Latin 1, Roman 8
All other models:
Italic, PC 437, PC 437 Greek, PC 850,
PC 852, PC 853, PC 855, PC 857,
PC 866, PC 869, ISO Latin 1T,
ISO 8859-7, MAZOWIA, Code MJK,
Bulgaria, Estonia, PC 774, PC 866 UKR,
ISO 8859-2, PC 866 LAT.
International character set for
Italic table
Italic U.S.A, Italic France, Italic
Germany, Italic U.K., Italic Denmark1,
Italic Sweden, Italic Italy, Italic Spain1
0 slash On, Off
High speed draft Off, On
Input buffer On, Off
Buzzer On, Off
Auto CR (IBM 2381Plus)** On, Off
IBM character table ** Table 2, Table 1
* The options available vary depending on the country.
**These settings take effect only when IBM 2381 Plus emulation is selected.
L
Sun-G+ Rev.C
A5 size Chapter 5
97/11/13 pass 0
5-4 Changing Printer Settings From the Printer’s Control Panel
Page length for front tractor
This setting allows you to set the page length (in inches) for
continuous paper loaded on the front push tractor.
Page length for rear tractor
This setting allows you to set the page length (in inches) for
continuous paper loaded on the rear push tractor.
Skip over perforation
This setting takes effect only when you are using continuous
paper. When you select On, the printer provides a one-inch
(25.4 mm) margin between the last line printed on one page
and the first line printed on the next page. Because most
application programs override margin settings made from the
control panel, you should use this setting only if you cannot set
your top and bottom margins using your application.
Auto tear off
When you turn on this setting and print on continuous paper
with the front or rear push tractor, the printer automatically
advances the paper perforation to the tear-off position, where
you can easily tear off the printed page(s). When the printer
receives the next print job, it automatically moves the unused
paper back to the top-of-form position and starts printing, so
no paper is wasted between print jobs.
When you select Off and print on continuous paper with the
front or rear push tractor, you need to move the perforation to
the tear-off position manually by pressing the Tear Off/Bin
button. See “Advancing the Paper to the Tear-Off Edge” in
Chapter 2 for more information. (The tear-off feature is not
available for paper loaded on the pull tractor.)
5
R
Sun-G+ Rev.C
A5 size Chapter 5
97/11/13 pass 0
Changing Printer Settings From the Printer’s Control Panel 5-5
Auto line feed
When you turn on this setting, each carriage return (CR) code
received by the printer is accompanied by a line feed code. This
moves the print position to the beginning of the next line. If the
printer adds an extra line after every carriage return, select Off.
Print direction
You can choose automatic print direction selection,
bidirectional printing (Bi-D), or unidirectional printing (Uni-D).
Printing is normally bidirectional; however, unidirectional
printing allows for precise vertical printing alignment, which
is useful for printing graphics.
I/F (interface) mode
The printer comes with a built-in parallel interface and an
interface slot in which you can install one optional interface.
For information on using an optional interface, see page A-3.
If your printer is connected to only one computer, select
Parallel or Optional for the interface mode, depending on the
interface you use. If your printer is connected to more than one
computer, select Auto (automatic) for the interface mode to
cause the printer to automatically switch between interfaces
depending on which one is receiving data.
Auto I/F (interface) wait time
This setting takes effect only if an optional interface is installed
and the auto interface mode is selected. This setting determines
how long the printer waits when it no longer receives data
from an interface before it checks whether a print job is being
sent through the other interface. You can specify 10 seconds
or 30 seconds for the auto interface wait time.
Software
If you select ESC/P, the printer operates in the EPSON ESC/P
mode. If you select IBM 2381 Plus, the printer emulates an IBM
printer.
L
Sun-G+ Rev.C
A5 size Chapter 5
97/11/13 pass 0
5-6 Changing Printer Settings From the Printer’s Control Panel
Character table
You can select among 11 standard character tables as well as
tables for 19 other countries. See Appendix C for character
samples.
International character set for Italic table
You can select among several international character sets for
the Italic character table. Each character set contains eight
characters that vary depending on the country or language, so
you can customize the Italic table to suit your printing needs.
See Appendix C for character samples.
0 slash
When you turn on this setting, the zero character contains a
slash (0); otherwise it has no slash (0). The slash allows you to
easily distinguish between the uppercase letter “O” and a zero.
High speed draft
When you choose On, the printer prints up to 500 cps
(characters per second) at 10 cpi (characters per inch). When
you choose Off, the printer prints up to 455 cps at 12 cpi.
Input buffer
When you turn on this setting, the printer’s input buffer stores
up to 64KB of data sent from your computer, freeing up your
computer for other tasks while the printer prints. When you
select Off, the buffer cannot store data, so the computer must
wait for the printer to print each character before it sends the
next character.
Buzzer (beeper)
When you turn on this setting, the printer beeps when an error
occurs. See page 7-2 for more information on printer errors. If
you do not want the printer to beep when an error occurs,
select Off.
5
R
Sun-G+ Rev.C
A5 size Chapter 5
97/11/13 pass 0
Changing Printer Settings From the Printer’s Control Panel 5-7
Auto CR (carriage return)
This setting is available only in IBM 2381 Plus emulation mode.
When you select On, each line feed (LF) code or ESC J code
received by the printer is accompanied by a carriage return
code. This moves the print position to the beginning of the next
line. If the printer adds an extra line after every carriage return,
select Off.
IBM character table
This setting is available only in IBM 2381 Plus emulation mode.
When you select Table 1, hex codes 00 to 1FH and 80H to 9FH
of the character tables are used for the control codes. When you
select Table 2, hex codes 00 to 1FH are used for the control
codes. See Appendix C for character samples.
Changing default settings
Follow the steps below to enter the default-setting mode and
change the printer’s default settings.
Note:
RTo print the language selection and default-setting mode
instructions, you need three sheets of A4- or letter-size
single-sheet paper or three pages of continuous paper that is at
least 279 mm (11 inches) long and 210 mm (8.27 inches) wide.
See Chapter 2 for instructions on loading continuous paper, or
Chapter 3 for instructions on loading single sheets.
RIf you use single sheets, you need to load a new sheet of paper
each time the printer ejects a printed sheet.
L
Sun-G+ Rev.C
A5 size Chapter 5
97/11/13 pass 0
5-8 Changing Printer Settings From the Printer’s Control Panel
1. Make sure paper is loaded and the printer is turned off.
cCaution:
Whenever you turn off the printer, wait at least five seconds
before turning it back on; otherwise you may damage the
printer.
2. Hold down the Pitch button while you press the Operate
button to turn on the printer. The printer enters the
default-setting mode and prints the language selection
instructions (one page).
3. Press the Pitch button until the Pitch lights indicate the
language you want, as described in the language selection
instructions.
4. Press the Font button to print the default-setting mode
instructions (two pages) in the language you selected.
The printed instructions list the default settings you can change,
describe how to change them, and show you how the control
panel lights help you make settings. Follow these instructions
to change the default settings using the buttons on the
printer’s control panel.
Note:
The arrows on the instruction sheets indicate the printer’s current
settings.
5. When you finish making settings, press the Operate button to
turn off the printer and exit the default-setting mode. Any
settings you have made remain in effect until you change them
again.
Note:
You may exit the default-setting mode by turning off the printer while
the printer is not printing.
5
R
Sun-G+ Rev.C
A5 size Chapter 5
97/11/13 pass 0
Changing Printer Settings From the Printer’s Control Panel 5-9
Chapter 6
Using EPSON Status Monitor 2
Proof Sign-off:
Yamanouchi _______
Grady _______
About the EPSON Status Monitor 2 Utility . . . . . . . . . . . 6-2
Installing EPSON Status Monitor 2 . . . . . . . . . . . . . . . . 6-3
Accessing EPSON Status Monitor 2 . . . . . . . . . . . . . . . . 6-4
Checking Printer Status Information . . . . . . . . . . . . . . . 6-4
Using the EPSON Status Monitor 2 window . . . . . . . . . . . 6-4
Using the Printer Status window . . . . . . . . . . . . . . . . . . 6-9
Making Monitoring Preference Settings . . . . . . . . . . . . . 6-10
Turning on background monitoring . . . . . . . . . . . . . . . . 6-11
Using the background monitoring icon . . . . . . . . . . . . . . 6-13 6
R
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
Using EPSON Status Monitor 2 6-1
About the EPSON Status Monitor 2 Utility
The EPSON Status Monitor 2 utility comes with your printer
but is available only for use with Microsoft Windows 95. It
allows you to monitor your printer’s status, alerts you when
printer errors occur, and provides troubleshooting instructions
when needed.
Note:
To monitor an FX-2180 printer on a network, you must install an
optional Ethernet interface card (C82357@) in your printer and use the
Status Monitor utility that comes with this card. See the manual that
comes with the interface card for instructions on using the Status
Monitor in a network environment.
Before using the Status Monitor, be sure to read the README
file on Disk 1 of the EPSON Status Monitor 2 software. You can
also find this README file in the EPSON Status Monitor 2
folder, located in the EPSON folder on your hard drive. This
file contains the latest information on the Status Monitor.
L
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
6-2 Using EPSON Status Monitor 2
Installing EPSON Status Monitor 2
To install the Status Monitor, follow these steps:
1. Make sure that you have installed the printer driver for
Windows 95. If not, install the printer driver for Windows 95
as described in Chapter 1.
Note:
If you installed the Status Monitor before the driver, install the
printer driver, then install the Status Monitor again.
2. Insert Disk 1 of the EPSON Status Monitor 2 software in a disk
drive.
3. Click Start and then click Run.
4. Type A:\Setup. (If you inserted the disk in a drive other than
drive A, substitute the appropriate letter.) Then click OK.
5. Follow the on-screen instructions, then click Finish to complete
the installation procedure.
After you install EPSON Status Monitor 2 and restart your
computer, the Status Monitor starts automatically and adds a
printer-shaped background monitoring icon to the taskbar at
the bottom of your computer screen. This icon only appears
when the Status Monitor is active.
6
R
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
Using EPSON Status Monitor 2 6-3
Accessing EPSON Status Monitor 2
To open the EPSON Status Monitor 2 window shown below,
double-click the printer-shaped background monitoring icon
on the taskbar at the bottom of your computer screen. You can
also open this window from Start. Click Start, point to
Programs and Epson, then click EPSON Status Monitor 2.
Checking Printer Status Information
This section describes how to use the Status Monitor to get
general and detailed printer status information.
Using the EPSON Status Monitor 2 window
You can select many Status Monitor menu commands by
clicking the buttons on the toolbar from this window. When
you point to a toolbar button, the corresponding menu
command appears briefly on your screen, and you see an
explanation of the button’s function in the status bar at the
bottom of the EPSON Status Monitor 2 window.
The main features of the EPSON Status Monitor 2 window are
described below.
status
L
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
6-4 Using EPSON Status Monitor 2
Installed Printers list
This list displays information about the EPSON printers
connected directly to your computer. If you select List from the
View menu, the list displays only the printer names and icons.
If you select Details, the list displays the printer name, status,
and job count of each printer.
When you install the Status Monitor, it automatically adds the
names and icons of all the EPSON printers connected to your
computer to this list. To add or delete a printer from the list,
select Add Printer or Delete Printer from the Settings menu.
To save computer memory, delete any printers you do not
need to monitor. (Doing so does not remove the printer driver
from your computer.)
The appearance of the icon next to each printer name changes
depending on the printer’s status as described in the table
below. See online help for more information.
Icon appearance Description
Green The printer is ready to print, or currently
printing.
Yellow The printer needs routine maintenance.
Red A printer error has occurred and your
printer cannot print. See Chapter 7 for
troubleshooting information.
Dimmed There is a communication problem
between the printer and the Status
Monitor.
The Status column of the Installed Printers list displays brief
messages describing the current status of each printer, and the
Job Count column displays the number of jobs waiting to print
on each printer.
Note:
You can arrange the printers in the Installed Printers list according to
the information in the Printer Name, Status, or Job Count column. Click
the Printer Name, Status, or Job Count title bar to change the
printer order.
6
R
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
Using EPSON Status Monitor 2 6-5
Printer menu
To get detailed information on the status of each printer in the
Installed Printers list, select a printer from the list, then select
from the Printer menu options described below.
TPrinter Status Opens the Printer Status window, which
provides detailed information on the
selected printer’s status. To use the
Printer Status window, see page 6-9.
TJob Status Provides information about the jobs
waiting to print on the selected printer.
TSelect Paper
Memory Not available.
TClose Closes the EPSON Status Monitor 2
window.
SPRINT
L
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
6-6 Using EPSON Status Monitor 2
View menu
To control the appearance and content of the EPSON Status
Monitor 2 window and the Installed Printers list, select from
the View menu options described below.
TToolbar/Status
Bar Shows or hides the toolbar and status
bar in the EPSON Status Monitor 2
window.
TLarge Icons/
Small Icons Changes the size of the printer icons
in the Installed Printers list.
TList Displays only the printer names and
icons in the Installed Printers list.
TDetails Displays the printer name and icon,
status, and number of jobs waiting to
print for each printer in the Installed
Printers list.
TRefresh Updates the printer status information
shown in the Installed Printers list.
SVIEW
6
R
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
Using EPSON Status Monitor 2 6-7
Settings menu
Use the Settings menu options described below to adjust the
monitoring interval for the printer, add and delete printers
from the Installed Printers list, or activate the Status Monitor.
TMonitoring
Preferences Opens the Monitoring Preferences
dialog box, where you can adjust the
monitoring interval and make
background monitoring settings for
the selected printer. For more
information, see “Turning on
background monitoring” on page 6-11.
TAdd Printer/
Delete Printer Allows you to select the printers you
want to monitor by adding or deleting
printers in the Installed Printers list.
TBackground
Monitoring Activates the Status Monitor.
(A printer-shaped icon appears on the
taskbar at the bottom of your computer
screen.)
Note:
The Background Monitoring and Status
Alert settings in the Monitoring
Preferences dialog box are not available
while the Status Monitor is inactive.
SSETTING
L
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
6-8 Using EPSON Status Monitor 2
TSelect
background
monitoring icon
Changes the appearance of the icon
that is displayed on the taskbar when
background monitoring is active.
Help menu
Click Help in the EPSON Status Monitor 2 window to view
online help. Click About to view the Status Monitor’s version
number and copyright information.
Using the Printer Status window
You can open the Printer Status window shown below to see
detailed information on the status of a printer. To open the
Printer Status window, double-click a printer in the Installed
Printers list, or select a printer and then choose Printer Status
from the Printer menu of the EPSON Status Monitor 2 window.
You can also access the Printer Status window by clicking the
Details button in the Status Alert dialog box. For information
on the Status Alert dialog box, see “Making Monitoring
Preference Settings” on page 6-10.
printer
6
R
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
Using EPSON Status Monitor 2 6-9
The Printer Status window contains two menus: the Current
Status and Printer Information menus. To open the menus,
click the tabs at the top of the Printer Status window.
Current Status menu
The printer illustration and message boxes on this menu give
you detailed printer status information. The appearance of the
printer illustration changes to reflect the current printer status,
described in the upper message box. If a printer error occurs,
the lower message box displays troubleshooting tips.
Printer Information menu
If your printer is connected to your computer through a
network, this menu provides information on network
connections and other printer resources.
Making Monitoring Preference Settings
The Monitoring Preferences dialog box allows you to turn on
the background monitoring feature and specify the monitoring
interval (the length of time between status information
updates) for the selected printer. To open the Monitoring
Preferences dialog box, see “Turning on background
monitoring” on the next page.
When you turn on background monitoring, the Status Monitor
updates the status information for the selected printer “in the
background” whenever you are using your computer. A Status
Alert dialog box is displayed in the lower right corner of your
computer screen. It provides short messages, and a Details
button that allows you to open the Printer Status window.
L
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
6-10 Using EPSON Status Monitor 2
Turning on background monitoring
Follow the steps below to monitor the selected printer and
specify when the Status Alert dialog box appears.
1. Make sure the Status Monitor is active. (It is active if a printer-
shaped icon appears on the taskbar at the bottom of your
computer screen.) If the icon is not on the taskbar, access
EPSON Status Monitor 2 from the Start menu as described on
page 6-4. Then point to Background Monitoring on the
Settings menu and click Monitor from restart or Monitor
now.
2. Select the printer you want to monitor from the Installed
Printers list, and then click Monitoring Preferences on the
Settings menu. The dialog box below appears.
Note:
The Background Monitoring and Status Alert settings in the
Monitoring Preferences dialog box are not available while the Status
Monitor is inactive.
prefer
6
R
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
Using EPSON Status Monitor 2 6-11
3. Use the slider to adjust the monitoring interval, if necessary.
Note:
Setting a short monitoring interval may cause some applications to
run more slowly.
4. Click Monitor this printer to turn on background monitoring
for the selected printer and view the Status Alert options.
5. Click the Status Alert options to specify when you want the
Status Alert dialog box to appear.
6. Click OK to save your settings and close the Monitoring
Preferences dialog box.
Using the background monitoring icon
A printer-shaped background monitoring icon appears on the
taskbar on your computer screen when the Status Monitor is
active. (To activate the Status Monitor, see step 1 of ”Turning
on background monitoring” on page 6-11.)
Double-clicking the background monitoring icon opens the
EPSON Status Monitor 2 window. Right-clicking this icon
opens a pop-up menu where you can choose whether the
Status Alert dialog box will appear in front of other windows
on the desktop. This pop-up menu also allows you to
deactivate the Status Monitor. When you deactivate the Status
Monitor, the background monitoring icon disappears from the
taskbar.
L
Sun-G+ Rev.C
A5 size Chapter 6
11/14/97 pass 0
6-12 Using EPSON Status Monitor 2
Chapter 7
Troubleshooting
Proof Sign-off:
Yamanouchi _______
Grady _______
Using the Error Indicators . . . . . . . . . . . . . . . . . . . . . 7-2
Problems and Solutions . . . . . . . . . . . . . . . . . . . . . . 7-4
Power supply problems . . . . . . . . . . . . . . . . . . . . . . . 7-5
Single-sheet paper loading or feeding problems . . . . . . . . . 7-6
Continuous paper loading or feeding problems . . . . . . . . . 7-8
Wrong top-of-form position . . . . . . . . . . . . . . . . . . . . . 7-9
Wrong tear-off position . . . . . . . . . . . . . . . . . . . . . . . 7-10
Printing or printout quality problems . . . . . . . . . . . . . . . 7-11
Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . 7-16
Aligning Vertical Lines in Your Printout . . . . . . . . . . . . . 7-17
Printing a Self Test . . . . . . . . . . . . . . . . . . . . . . . . . 7-18
Printing a Hex Dump . . . . . . . . . . . . . . . . . . . . . . . . 7-19 7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-1
Using the Error Indicators
You can identify many common printer problems using the
lights on the control panel. If your printer stops working and
one or more control panel lights are on or flashing or the
printer beeps, use the following table to diagnose and fix the
problem. If you can’t fix your printer problem using this table,
go to the next section.
State of
panel lights Beep
pattern Problem
Solution
n Pause −The printer is paused.
Press the Pause button to resume printing.
•••
The printer cover is open.
Close the printer cover and press the Pause button to
resume printing.
•••••
Paper from another paper source is currently in the paper
path.
Move the paper release lever back to the appropriate
position and press the Load/Eject button to feed the
paper out of the paper path. Then set the lever to the
position you want to use. Press the Pause button to turn
off the Pause light, if necessary.
n Paper Out
n Pause •••
No paper is loaded in the selected paper source.
Load paper in the printer. Then press the Pause button to
turn off the Pause light, if necessary.
•••
The paper is not loaded correctly.
Remove your paper and reload it correctly. See
Chapter 2 (continuous paper) or Chapter 3 (single sheets)
for instructions on loading paper. Then press the Pause
button to turn off the Pause light, if necessary.
••• Paper is jammed in the printer.
Clear the paper jam as described on page 7-16.
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-2 Troubleshooting
State of
panel lights Beep
pattern Problem
Solution
f Paper Out
n Pause
•••
Continuous paper is not fed to the standby position.
Tear off the printed document at the perforation; then
press the Load/Eject button. The printer feeds the paper
to the standby position. Press the Pause button to turn off
the Pause light.
•••
A single sheet of paper is not fully ejected.
Press the Load/Eject button to eject the sheet. Then press
the Pause button to turn off the Pause light, if necessary.
••• Paper is jammed in the printer.
Clear the paper jam as described on page 7-16.
f Pause
−
The print head is overheated.
Wait a few minutes; the printer resumes printing
automatically once the print head cools.
f Paper Out
f Pause
f f
Tear Off/Bin
f f Font
−
An unknown printer error has occurred.
Turn off the printer and leave it off for several minutes;
then turn on the printer again. If the error recurs, contact
your dealer.
n = on,
f = flashing
••• = short series of beeps (three beeps), ••••• = long series of beeps (five beeps)
Note:
The printer beeps once if you press a control panel button when the
corresponding function is not available.
7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-3
Problems and Solutions
Most printer problems are easy to solve. Use the information in
this section to find the source of and solution to any printer
problems that occur.
Determine the type of problem that occurred, and see the
appropriate page below:
Power supply problems . . . . . . . . . . . . . 7-5
Single-sheet paper loading or
feeding problems . . . . . . . . . . . . . . . . . 7-6
Continuous paper loading or
feeding problems . . . . . . . . . . . . . . . . . 7-8
Wrong top-of-form position . . . . . . . . . . . . 7-9
Wrong tear-off position . . . . . . . . . . . . . . . 7-10
Printing or printout quality problems . . . . . . 7-11
You can also use the self test to determine whether the printer
or the computer is causing the problem. See page 7-18 for
instructions on printing a self test. To pinpoint communication
problems, experienced users may want to use the printer’s hex
dump mode, described on page 7-19.
To clear a paper jam, see page 7-16.
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-4 Troubleshooting
Power supply problems
The control panel lights come on briefly, but then go off and
stay off.
Cause What to do
The printer’s voltage rating
does not match the voltage
of your electrical outlet.
Check the printer and the outlet
voltage ratings. If the voltages do
not match, unplug the printer
immediately and contact your dealer.
wWarning:
Do not reconnect the power cord to an electrical outlet that has the
wrong voltage for your printer.
The printer does not work and the control panel lights are off
even though you turned on the printer.
Cause What to do
The power cord is not
properly plugged into the
electrical outlet or your
printer.
Press the Operate button to turn off
the printer, and make sure the power
cord is firmly plugged into the
electrical outlet and the printer, if
necessary. Then press the Operate
button to turn on the printer.
The electrical outlet does not
work.
Use a different outlet.
7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-5
Single-sheet paper loading or feeding problems
The printer does not load single-sheet paper or does not feed
it properly.
Cause What to do
The paper release lever is set
to a tractor position.
Set the paper release lever to the
single-sheet position. For more
information on setting the paper
release lever, see Chapter 2.
Continuous paper is in the
paper path.
Set the paper release lever to the
appropriate tractor position and press
the Load/Eject button to feed the
continuous paper to the standby
position. Then set the paper release
lever to the single-sheet position. (See
Chapter 2 for more information on
switching to printing on single sheets.)
The paper on the paper guide
is positioned too far to the
right for the printer to detect
that it is there.
Move the paper a little to the left.
Single-sheet paper is not
loaded properly.
See Chapter 3 for instructions on
loading single-sheet paper.
The paper thickness lever is
not set correctly.
Set the paper thickness lever to match
the thickness of your paper. See
“Setting the Paper Thickness Lever” in
Chapter 2.
Your paper is creased, old, too
thin, or too thick.
See the paper specifications in
Appendix C and use new, clean sheets
of paper.
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-6 Troubleshooting
The printer does not fully eject a single sheet.
Cause What to do
Your paper is too long. Press the Load/Eject button to eject
the sheet. Make sure the page length
of your paper is within the range
specified for single-sheet paper in
Appendix C. Also check and adjust the
paper size setting in your application
or printer driver.
The optional cut-sheet feeder does not feed your single-sheet
paper properly.
Cause What to do
The cut-sheet feeder is not
installed properly.
Reinstall it as described in Appendix A.
Too many sheets are loaded in
the cut-sheet feeder.
Load no more than 150 single sheets in
the high-capacity cut-sheet feeder. See
“Using the Optional Cut-Sheet
Feeders” in Appendix A for more
information.
The edge guides of the
cut-sheet feeder are not
positioned correctly.
Align the left edge guide with the
arrow mark, then move the right edge
guide to match your paper’s width.
There is only one sheet left in
the bin.
Load more paper in the cut-sheet
feeder.
7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-7
Continuous paper loading or feeding problems
The printer does not load continuous paper or does not feed it
properly.
Cause What to do
The paper release lever is not
set correctly.
Set the paper release lever to the tractor
position for the paper source you want
to use. For more information on setting
the paper release lever, see Chapter 2.
Single-sheet paper is in the
paper path.
Set the paper release lever to the
single-sheet position and press the
Load/Eject button to eject the sheet.
Then set the paper release lever back to
the appropriate tractor position. (See
Chapter 2 for more information on
switching to printing on continuous
paper.)
Continuous paper is not
loaded properly.
See Chapter 2 for instructions on
loading continuous paper on the
tractor you want to use.
The paper thickness lever is
not set correctly.
Set the paper thickness lever to match
the thickness of your paper. See
“Setting the Paper Thickness Lever” in
Chapter 2.
The printer does not feed continuous paper to the standby
position.
Cause What to do
You did not tear off the
printed pages before pressing
the Load/Eject button.
Tear off the printed pages at the
perforation. Then press the
Load/Eject button to feed the paper
backward to the standby position.
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-8 Troubleshooting
Wrong top-of-form position
Printing starts too high or low on the page.
Cause What to do
The paper size setting in your
application software or
printer driver does not match
the size of the paper you are
using.
Check the paper size setting in your
application or printer driver.
The printer’s page length
settings for the front or rear
tractor do not match the size
of the continuous paper you
are using.
Check the page length settings for the
front or rear tractor using the printer’s
default-setting mode or the EPSON
Remote! utility. See “About Your
Printer’s Default Settings” in Chapter
5, or “Using the EPSON Remote!
Utility” in Chapter 4.
The top margin or top-of-form
position setting is incorrect.
Check the margin or top-of-form
position setting in your application
software. See the printable area
specifications in Appendix C.
Adjust the top-of-form position in
micro adjust mode. However, settings
made in Windows applications
override settings made in micro adjust
mode. See “Adjusting the Top-of-Form
Position” in Chapter 2.
The printer you want to use is
not selected in your software.
Choose the correct printer from the
Windows desktop or in your
application before printing.
You moved the paper using
the knob while the printer
was on.
Adjust the top-of-form position using
the micro adjust feature. See “Adjusting
the Top-of-Form Position” in Chapter 2.
cCaution:
Never use the knob to adjust the top-of-form position; this may damage
the printer or cause it to lose the top-of-form position.
7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-9
Wrong tear-off position
The printer prints on (or too far away from) the perforation of
your continuous paper.
Cause What to do
The tear-off position setting is
incorrect.
Adjust the tear-off position using the
micro adjust feature. See “Adjusting
the tear-off position” in Chapter 2.
You moved the paper using
the knob while the printer
was on.
Adjust the tear-off position using the
micro adjust feature. See “Adjusting
the tear-off position” in Chapter 2.
cCaution:
Never use the knob to adjust the tear-off position; this may damage the
printer or cause it to lose the tear-off position.
The printer you want to use is
not selected in your software.
Choose the correct printer from
the Windows desktop or in your
application before printing.
The paper size setting in your
application or printer driver
does not match the size of the
paper you are using.
Check the paper size setting in your
application or printer driver.
The printer’s page length
settings for the front or rear
tractor do not match the size
of the continuous paper you
are using.
Check the page length settings for
the front or rear tractor using the
printer’s default-setting mode or the
EPSON Remote! utility. See “About
Your Printer’s Default Settings” in
Chapter 5, or “Using the EPSON
Remote! Utility” in Chapter 4.
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-10 Troubleshooting
Printing or printout quality problems
The printer does not print when the computer sends data.
Cause What to do
The printer is paused. Press the Pause button.
The printer cover is open. Close the printer cover and press the
Pause button to resume printing.
The interface cable is not
plugged in securely.
Check that both ends of the cable
between the printer and the computer
are plugged in securely. If the cable is
connected correctly, run a self test as
described later in this chapter.
Your interface cable does not
meet the printer and/or
computer specifications.
Use an interface cable that meets the
requirements of both the printer and
computer. See page A-3 and your
computer documentation.
Your software is not properly
set up for your printer.
Select your printer from the Windows
desktop or in your application. If
necessary, install or reinstall the printer
driver software as described in
Chapter 1.
7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-11
The printer makes noise, but nothing prints or printing stops
abruptly.
Cause What to do
The paper thickness lever is
set incorrectly.
Set the paper thickness lever to match
the thickness of your paper. See
“Setting the Paper Thickness Lever” in
Chapter 2.
The ribbon has too much
slack, the ribbon has come
loose, or the ribbon cartridge
is not installed properly.
Remove any slack in the ribbon by
turning the ribbon-tightening knob,
or reinstall the ribbon cartridge as
described in Chapter 1.
The printout is faint.
Cause What to do
The paper thickness lever is
set incorrectly for your paper.
Move the paper thickness lever to a
lower setting.
The ribbon is worn out. Replace the ribbon cartridge as
described in Chapter 1.
You printed on continuous
multi-part forms with seven
parts (one original plus six
copies) in ordinary printing
mode.
Turn on the double-strike mode when
you print on continuous multi-part
forms with seven parts. See page 2-6
for instructions.
The printout has gaps.
Cause What to do
The paper thickness lever is
not set correctly.
Set the paper thickness lever to match
the thickness of your paper. See page
2-4 for continuous paper, or page 3-3
for single sheets.
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-12 Troubleshooting
Part of the printout is missing, or dots are missing in random
positions.
Cause What to do
The ribbon has too much
slack, the ribbon has come
loose, or the ribbon cartridge
is not installed properly.
Remove any slack in the ribbon by
turning the ribbon-tightening knob, or
reinstall the ribbon cartridge as
described in Chapter 1.
The ribbon is worn out. Replace the ribbon cartridge as
described in Chapter 1.
Lines of dots are missing in the printout.
Cause What to do
The print head is damaged. Stop printing and contact your dealer
to have the print head replaced.
cCaution:
Never replace the print head yourself; you may damage the printer.
Also, other parts of the printer must be checked when the print head is
replaced.
All the text is printed on the same line.
Cause What to do
No line feed command is sent
at the end of each line of text.
Turn on the auto line feed setting using
the printer’s default-setting mode or
the EPSON Remote! utility so that the
printer automatically adds a line feed
code to each carriage return. See
“About Your Printer’s Default
Settings” in Chapter 5 or “Using the
EPSON Remote! Utility” in Chapter 4.
7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-13
The printout has extra blank lines between lines of text.
Cause What to do
Two line feed commands are
being sent at the end of each
line of text.
Turn off the auto line feed setting
using the printer’s default-setting
mode or the EPSON Remote! utility.
See “About Your Printer’s Default
Settings” in Chapter 5, or “Using the
EPSON Remote! Utility” in Chapter 4.
The line space setting in your
application software is
incorrect.
Adjust the line space setting in your
application software.
The skip-over-perforation
setting is on.
Turn off the skip-over-perforation
setting in the default-setting mode or
the EPSON Remote! utility. See “About
Your Printer’s Default Settings” in
Chapter 5, or “Using the EPSON
Remote! Utility” in Chapter 4.
The printer prints strange symbols, incorrect fonts, or other
inappropriate characters.
Cause What to do
Your printer and computer
are not communicating
correctly.
Make sure that you are using the
correct interface cable and that the
communications protocol is correct.
See page A-3 and your computer
documentation. If you installed an
optional serial interface card, also see
page A-18.
The wrong character table is
selected in your software.
Select the correct character table using
your software, the default-setting
mode, or the EPSON Remote! utility.
The character table setting in your
software overrides settings made in
the default-setting mode or EPSON
Remote!.
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-14 Troubleshooting
The printer you want to use is
not selected in your software.
Choose the correct printer from the
Windows desktop or in your
application before printing.
Your application software is
not configured correctly for
your printer.
Make sure that your application
software is set up correctly for your
printer. See your application
documentation. If necessary, install or
reinstall the printer driver software as
described in Chapter 1.
Software settings override
settings you make using the
default-setting mode, EPSON
Remote!, or the control panel
buttons.
Use your application software to select
the font.
Vertical printed lines are not aligned.
Cause What to do
Bidirectional printing, which
is the printer’s standard
printing mode, is out of
alignment.
Use the printer’s bidirectional
adjustment mode to correct this
problem. See “Aligning Vertical Lines
in Your Printout” later in this chapter.
7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-15
Clearing Paper Jams
To clear a paper jam, follow these steps:
1 Press the Operate button to turn off the printer.
2. If a single-sheet of paper is stuck on the paper guide, gently
remove it.
3. Remove the printer cover. If you are loading continuous paper
from the rear slot, remove the paper guide.
4. If continuous paper is jammed in the printer, tear off the fresh
supply at the perforation nearest the paper entry slot.
5. Turn the knob on the right side of the printer away from you to
eject the paper in the printer. Remove any remaining pieces of
paper.
cCaution:
Use the knob on the right side of the printer only to clear
paper jams when the printer is off. Otherwise, you may
damage the printer or lose the top-of-form or tear-off
position.
6. Replace the paper guide if necessary, and replace the printer
cover. Then close the paper guide cover.
7. Press the Operate button to turn on the printer. Make sure the
Paper Out and Pause lights are off.
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-16 Troubleshooting
Aligning Vertical Lines in Your Printout
If you notice that the vertical lines in your printout are not
properly aligned, you can use the printer’s bidirectional
adjustment mode to correct this problem.
Note:
TTo complete the steps below, you need four sheets of A3-size
single-sheet paper or four pages of continuous paper that are at
least 279 mm (11 inches) long and 376 mm (14.8 inches) wide.
See Chapter 2 for instructions on loading continuous paper, or
Chapter 3 for instructions on loading single sheets.
TIf you use single sheets, you need to load a new sheet of paper each
time the printer ejects a printed sheet onto the paper guide.
Follow these steps to perform the bidirectional adjustment:
1. Make sure paper is loaded and the printer is turned off.
cCaution:
Whenever you turn off the printer, wait at least five seconds
before turning it back on; otherwise you may damage the
printer.
2. While holding down the Pause button, press the Operate
button to turn on the printer. The printer enters the
bidirectional adjustment mode and then prints instructions
and the first set of alignment patterns.
3. As described in the instructions, compare the alignment
patterns and select the pattern with the best alignment.
4. Follow the instructions to print the remaining sets of alignment
patterns and select the pattern with the best alignment in each
set.
5. After you select the best pattern in the final set of alignment
patterns, press the Operate button to turn off the printer and
exit the bidirectional adjustment mode. Your selections are
saved automatically.
7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-17
Printing a Self Test
Running the printer’s self test helps you determine whether the
printer or the computer is causing the problem:
TIf the self test results are satisfactory, the printer is working
properly and the problem probably results from your
printer driver settings, application settings, computer, or
interface cable. (Be sure to use a shielded interface cable.)
TIf the self test does not print properly, there is a problem
with the printer. See “Problems and Solutions” for possible
causes and solutions to the problem.
You can print the self test using either single sheets or
continuous paper. See Chapter 2 for instructions on loading
continuous paper, or Chapter 3 for instructions on loading
single sheets.
Note:
Use paper that is at least 376 mm (14.8 inches) wide, such as A3-size
paper.
To perform a self test, follow these steps:
1. Make sure paper is loaded and the printer is turned off.
cCaution:
Whenever you turn off the printer, wait at least five
seconds before turning it back on; otherwise you may
damage the printer.
2. To run the test using the Draft font, hold down the LF/FF button
while you press the Operate button to turn on the printer. To
run the test using the printer’s near letter-quality fonts (Roman
and Sans Serif), hold down the Load/Eject button while you
turn on the printer. Either self test can help you determine the
source of your printing problem; however, the draft test prints
faster than the near letter-quality test.
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-18 Troubleshooting
After a few seconds, the printer loads the paper automatically
and begins printing the self test. A series of characters is
printed.
Note:
To temporarily stop the self test, press the Pause button. To resume
the test, press the Pause button again.
3. To end the self test, press the Pause button to stop printing and
the Load/Eject button to eject the printed page. Then turn off
the printer.
Printing a Hex Dump
If you are an experienced user or a programmer, you can print
a hexadecimal dump to isolate communication problems
between the printer and your software program. In hex dump
mode, the printer prints all data received from the computer as
hexadecimal values.
You can print a hex dump using either single sheets or
continuous paper. See Chapter 2 for instructions on loading
continuous paper, or Chapter 3 for instructions on loading
single sheets.
Note:
Use paper that is at least 210 mm (8.3 inches) wide, such as A4- or
letter-size paper.
7
Troubleshooting
R
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
Troubleshooting 7-19
To print a hex dump, follow the steps below.
1. Make sure paper is loaded and the printer is turned off.
cCaution:
Whenever you turn off the printer, wait at least five seconds
before turning it back on; otherwise you may damage the
printer.
2. To enter hex dump mode, hold down both the LF/FF and
Load/Eject buttons while you press the Operate button to
turn on the printer.
3. Open a software program and send a print job to the printer.
Your printer prints all the codes it receives in hexadecimal
format.
If characters are printable, they appear in the right column as
ASCII characters. Nonprintable codes, such as control codes,
are represented by dots. By comparing the characters printed
in the right column with the printout of the hexadecimal
codes, you can check the codes the printer is receiving.
4. To exit hex dump mode, press the Pause button to stop printing
and the Load/Eject button to eject the printed page(s). Then
turn off the printer.
dump
L
Sun-G+ Rev.C
A5 size Chapter 7
97/11/14 pass 1
7-20 Troubleshooting
Appendix A
Enhancing Your Printer With Options
Proof Sign-off:
Yamanouchi _______
Grady _______
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Paper handling options . . . . . . . . . . . . . . . . . . . . . . . A-2
Optional interface cards . . . . . . . . . . . . . . . . . . . . . . A-3
Using the Optional Cut-Sheet Feeders . . . . . . . . . . . . . . . . A-4
Installing the high-capacity or double-bin cut-sheet feeder . . A-4
Loading paper in the high-capacity cut-sheet feeder . . . . . . A-6
Selecting the paper source (bin 1 or bin 2) . . . . . . . . . . . . A-10
Switching between continuous paper and single-sheet
paper in the cut-sheet feeder . . . . . . . . . . . . . . . . . . . A-11
Using the Roll Paper Holder . . . . . . . . . . . . . . . . . . . . . . A-12
Assembling the roll paper holder . . . . . . . . . . . . . . . . . A-12
Installing the roll paper holder . . . . . . . . . . . . . . . . . . A-13
Loading roll paper . . . . . . . . . . . . . . . . . . . . . . . . . A-14
Removing roll paper . . . . . . . . . . . . . . . . . . . . . . . . A-16
Installing an Interface Card . . . . . . . . . . . . . . . . . . . . . . A-17
Using the C82305@ýor C82306@ serial interface card . . . . . . A-18
A
R
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
Enhancing Your Printer With Options A-1
Options
As described below, a variety of paper handling options and interface
cards are available for your printer. To purchase options, contact your
dealer or customer support as described in Appendix D.
Paper handling options
High-capacity cut-sheet feeder (C80673@)
Feeds up to 150 sheets of paper, 25 plain bond
envelopes, or 30 postcards into the printer
without reloading. You can also load a stack of
single-sheet multi-part forms up to 15 mm
(0.59 inch) thick in this feeder. For instructions
on using this option, see page A-4.
Second bin cut-sheet feeder (C80674@)
Connects to the high-capacity cut-sheet feeder
to create a double-bin cut-sheet feeder. You
can load up to 50 sheets of ordinary
single-sheet paper in the second-bin cut-sheet
feeder. For instructions on using this option,
see page A-4.
Pull tractor (C80032@)
Improves continuous paper handling and
reduces the chance of paper jams. Using a pull
tractor in conbination with a push tractor is
especially useful for printing on continuous
pre-printed forms, multi-part forms, and
labels, and for printing high-quality graphics.
For instructions on using this option, see
page 2-22.
4-4
4-4-2
a-2-3
L
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
A-2 Enhancing Your Printer With Options
Roll paper holder (#8310)
Allows you to use your printer with 8.5-inch
roll paper like that used with telex machines.
For instructions on using this option, see
page A-12.
Note:
The asterisk (@) is a substitute for the last digit of the product number, which
varies by country.
Optional interface cards
You can install an optional interface card to supplement your printer’s
built-in parallel interface and provide added network compatibility.
The EPSON interface cards in the table below are compatible with your
printer. (Not all interfaces are available in all countries.)
For instructions on installing an interface card, see page A-17.
Model number Name
C82305@#
/ C82306@Serial interface card
C82307@#
/ C82308@32KB serial interface card
C82310@ / C82311@32KB parallel interface card
C82312@LocalTalk interface card
C82313@32KB IEEE-488 interface card
C82314@Coax interface card
C82315@Twinax interface card
C82345@IEEE-1284 parallel interface card
C82357@Ethernet interface card
The asterisk (@) is a substitute for the last digit, which varies by country.
If you are unsure whether you need an optional interface or would like to
know more about interfaces, contact your dealer.
A
R
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
Enhancing Your Printer With Options A-3
Using the Optional Cut-Sheet Feeders
When you install the optional high-capacity cut-sheet feeder (C80673@),
you can load multiple single sheets of paper up to 150 sheets of in the
printer. Also you can create a double-bin cut-sheet feeder by connecting
the second bin cut-sheet feeder (C80674@) to the high-capacity cut-sheet
feeder. The double-bin cut-sheet feeder allows you to load two different
types of single-sheet paper in the printer at the same time and easily
switch between them. To assemble the double-bin cut-sheet feeder and
load paper in the second-bin cut-sheet feeder, see the second-bin cut-sheet
feeder manual. For instructions on selecting bin 1 or bin 2 of the
double-bin cut-sheet feeder, see page A-10.
Note:
The second-bin cut-sheet feeder can be used only in combination with the
high-capacity cut-sheet feeder; you cannot use it alone.
Installing the high-capacity or double-bin cut-sheet
feeder
You install the high-capacity cut-sheet feeder and double-bin cut-sheet
feeder in the same way. Follow the steps below.
Note:
Before installing the double-bin cut-sheet feeder, assemble it as described in the
cut-sheet feeder manual.
wWarning:
You will need to move the print head by hand before installing the
cut-sheet feeder. If you have just used the printer, the print head may
be hot; let it cool for a few minutes before touching it.
L
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
A-4 Enhancing Your Printer With Options
1. Make sure the printer is turned off.
cCaution:
Be sure to turn off the printer. You will need to move the print head
to the ribbon installation position before installing the high-capacity
cut-sheet feeder, and moving the print head while the printer is on
may damage the printer.
2. Remove the paper guide and printer cover. Then press up the tabs on
both sides of the paper tension unit and lift it up and off the printer. If
a tractor is installed in the pull position, remove it as described on
page 2-33. Store unused parts in a safe place.
3. Hold the cut-sheet feeder in both hands and fit the feeder’s notches over
the mounting posts on the printer as shown below. Then release the
latch levers and lower the cut-sheet feeder until it rests on the printer.
4. Insert the cable into the connector as shown above.
5. Replace the printer cover.
You are now ready to load paper in the cut-sheet feeder. To load paper in
the high-capacity cut-sheet feeder, see the next section. To load paper in
the second bin of the double-bin cut-sheet feeder, see the manual that
comes with the second-bin cut-sheet feeder. If you installed the
double-bin cut-sheet feeder, you need to select the paper source (bin 1 or
bin 2) as described on page A-10.
To remove the cut-sheet feeder, reverse the steps above.
4-1
A
R
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
Enhancing Your Printer With Options A-5
Loading paper in the high-capacity cut-sheet feeder
You can load up to 150 ordinary single sheets, 25 plain bond envelopes, or
30 postcards in the high-capacity cut-sheet feeder. You can also load a
stack of single-sheet multi-part forms up to 15 mm (0.59 inch) thick in this
feeder.
Follow the steps below to load paper in the high-capacity cut-sheet feeder.
cCaution:
Do not load carbon paper or labels in the high-capacity cut-sheet feeder.
1. Open the paper guide cover, and set the paper release lever to the
single-sheet position. Also make sure the paper thickness lever
(located under the printer cover) is set to the proper position for
your paper’s thickness.
2. Pull down the center support.
4-4A
center support
4-2-1
L
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
A-6 Enhancing Your Printer With Options
3. Release the left and right paper guides of the cut-sheet feeder by
pulling the lock levers forward.
4. Holding the lower portion of the left paper guide, slide it until it is
aligned with the arrow mark on the back of the center support. Then
push the left lock lever backward to lock it in place. Holding the
lower portion of the right paper guide, slide it to match the width of
your paper, but do not lock it.
5. Slide the paper stacker midway between the paper guides as shown
above.
4-2-2A
paper stacker
4-2-3
A
R
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
Enhancing Your Printer With Options A-7
6. As shown below, set the cut-sheet feeder’s paper type levers to the
proper position for the paper you will load: single-sheet paper or
postcards and envelopes.
Note:
Always set the paper type levers before you load paper.
7. Pull both paper set levers forward until the paper guides retract
and lock open to allow paper loading.
8. Take a stack of paper (up to 150 sheets of plain paper) and fan it.
Next, tap the side and bottom edges of the paper on a flat surface to
even up the stack.
9. Insert the paper stack printable side down along the left paper guide.
single-sheet paper or
single-sheet multi-part
forms
envelopes or postcards
4-3
4-3aa
L
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
A-8 Enhancing Your Printer With Options
10. Adjust the right paper guide so that it matches your paper’s width.
Make sure the position of the guide allows the paper to move up and
down freely. Then push the lock lever backward to lock the paper
guide.
11. Push back the paper set levers to clamp the paper against the guide
rollers.
12. Move the cut-sheet feeder’s paper selection lever to the single-sheet
position, as shown below. Then lift up the center support and close
the paper guide cover.
Note:
TAlways close the printer cover before printing. The printer does not print
when the cover is open.
TWhen the cut-sheet feeder is installed, you can still load single sheets one at a
time using the front paper slot.
The cut-sheet feeder automatically loads paper when the printer receives
data. Printed pages are stacked on the center support. If you need to eject
a sheet, press the Load/Eject button.
If the first printed line on your page appears too high or low, you can
adjust its position using the micro adjust feature. See “Adjusting the
Top-of-Form Position” on page 2-37.
cCaution:
Never use the knob to adjust the top-of-form position; this may damage
the printer or cause it to lose the top-of-form position.
continuous paper
position
single-sheet
position 4-4b
A
R
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
Enhancing Your Printer With Options A-9
Selecting the paper source (bin 1 or bin 2)
When the double-bin cut-sheet feeder is installed, you need to select the
paper source (bin 1 or bin 2) using your application or the printer’s control
panel. As shown below, the high-capacity cut-sheet feeder is bin 1 and the
second-bin cut-sheet feeder is bin 2.
It is best to select the paper source in your application program because
software settings usually override the printer’s control panel settings.
However, if you cannot select the paper source in your application, press
the Tear Off/Bin button until the lights indicate the bin you want as
shown below. When the printer receives data, it automatically loads paper
from the bin you select.
bin 2: second-bin
cut-sheet feeder
bin 1: high-capacity
cut-sheet feeder
g4-17
o n Bin 1 (the high-capacity cut-sheet
feeder) is selected.
n o Bin 2 (the second-bin cut-sheet
feeder) is selected.
n = On,
o = Off
3-1aa
L
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
A-10 Enhancing Your Printer With Options
Switching between continuous paper and single-sheet
paper in the cut-sheet feeder
You can easily switch between continuous paper on a push tractor and
single-sheet paper in the cut-sheet feeder without removing the
continuous paper.
Switching to continuous paper
1. If any single sheets are in the paper path, press the Load/Eject button
to eject them.
2. Move the printer’s paper release lever to the front or rear push tractor
position. Also set the paper thickness lever to the proper position for
the thickness of your continuous paper.
3. Move the cut-sheet feeder’s paper selection lever to the continuous
paper position.
Switching to single-sheet paper in the cut-sheet feeder
1. If any continuous paper remains in the printer, press the Tear Off/Bin
button to advance the paper to the tear-off position. Then tear off the
printed pages.
cCaution:
Tear off your printed document before you press the Load/Eject
button in the next step. Reverse feeding several pages at a time may
cause a paper jam.
2. Press the Load/Eject button. The printer feeds the continuous paper
backward to the standby position. The paper is still attached to the
push tractor but is no longer in the paper path.
3. Move the printer’s paper release lever to the single-sheet position. Also
set the paper thickness lever to the proper position for the thickness
of your single-sheet paper.
4. Move the cut-sheet feeder’s paper selection lever to the single-sheet
position.
5. If you are using the double-bin cut-sheet feeder, select the bin you want
to use as described on page A-10.
A
R
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
Enhancing Your Printer With Options A-11
Using the Roll Paper Holder
The optional roll paper holder (#8310) allows you to use 8.5-inch roll
paper like that used with telex machines. This provides an inexpensive
alternative to using continuous paper for applications that require
variable paper lengths. Before you install and use the roll paper holder,
you need to assemble it.
Assembling the roll paper holder
1. Fit the arc bearings into the stand as shown.
2. Make sure you orient the stand and base plate as shown below. Then
place the base plate on the stand and fasten the two together with the
plastic spacing clips.
g3-30-1
g3-30-2
L
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
A-12 Enhancing Your Printer With Options
3. Hook the tension lever onto both ends of the stand as shown below.
While pulling up the tension lever, fit the wire ends of the tension
lever into the holes in the stand. The roll paper holder is assembled.
Installing the roll paper holder
1. Make sure the printer is turned off.
2. Position the roll paper holder underneath the printer as shown below.
Fit the two positioning pegs on the bottom of the printer into the two
holes in the base plate.
cCaution:
The roll paper holder is not fastened to the printer; only the printer’s
weight and the two positioning pegs hold it in place. If you pick up the
printer, be careful not to drop the roll paper holder.
To remove the roll paper holder, carefully lift up the printer and pull out
the roll paper holder from beneath the printer.
tension lever
g3-30-3
4-6
A
R
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
Enhancing Your Printer With Options A-13
Loading roll paper
After you install the roll paper holder, follow the steps below to load a roll
of paper:
1. Make sure the printer is turned off. Then open the paper guide cover
and remove the paper guide.
2. Make sure the paper tension unit is installed.
3. Set the paper thickness lever (located under the printer cover) to the
proper position for the thickness of your roll paper.
4. Set the paper release lever to the single-sheet position.
5. Cut the leading edge of the roll paper straight across.
6. Insert the roll paper holder shaft into the center of the paper
roll as shown.
g3-31-2
g3-32-1
L
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
A-14 Enhancing Your Printer With Options
7. Place the shaft and paper roll on the roll paper holder so the paper
feeds from the bottom of the roll.
8. Turn on the printer. Then bring the leading edge of the paper up over
the rear push tractor and insert it until it meets resistance. The printer
loads the roll paper automatically.
9. Replace the paper guide and close the paper guide cover. You are now
ready to print. The printed roll paper is fed over the paper guide to
the back of the printer, as shown below.
g3-32-2
4-9
A
R
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
Enhancing Your Printer With Options A-15
When you finish printing, open the paper guide cover and press the
LF/FF button to advance the paper. Then tear off the paper using the
tear-off edge of the printer (pull it towards you for a clean cut).
Removing roll paper
Roll paper cannot be fed backward. To remove roll paper, open the paper
guide cover and remove the paper guide; then cut the paper behind where
it feeds into the printer. Press the Load/Eject button to eject the
remaining paper.
g3-43
NEW08
L
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
A-16 Enhancing Your Printer With Options
Installing an Interface Card
Follow the steps below to install an optional interface card.
1. Make sure the printer is turned off. Unplug the printer’s power cord
and disconnect the interface cable.
2. Remove the screws from the shield plate on the back of the printer and
remove the plate.
3. Slide the interface card along the slots on both sides of the interface
compartment. Firmly push in the card to make sure the connector at
the back of the interface card is fully inserted into the printer’s
internal socket. Then replace the screws and tighten them.
Note:
Store the shield plate in a safe place; you will need to reattach it if you remove the
interface card later.
To remove the interface card, reverse the steps above.
4-10
4-11
A
R
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
Enhancing Your Printer With Options A-17
Using the C82305
@ý
or C82306
@
serial interface card
To use the C82305@ or C82306@ serial interface card, see the sections
below regarding the baud rate, handshake timing, and error handling.
For all other data transfer conventions, such as word structure and
communications protocol, see your interface card manual.
Selecting a baud rate
You can select from the following baud rates: 300, 600, 1200, 2400, 4800,
9600, and 19200 bps (bits per second). To set the baud rate, see the bit-rate
selection table in your interface card manual.
Handshake timing
When the unused area for data in the input buffer drops to 256 bytes, the
printer outputs an X-OFF code or sets the DTR flag to 1 (MARK) to
indicate that it cannot receive data. When the unused area increases to 512
bytes, the printer outputs an X-ON code or sets the DTR flag to 0 (SPACE)
to indicate that it is ready to receive data.
Error handling
When the printer detects a parity error, the print data is replaced with an
asterisk (@). The printer ignores all other errors, including framing and
overrun errors.
L
Sun-G+ Rev.C
A5 size Appendix A
97/11/14 pass 1
A-18 Enhancing Your Printer With Options
Appendix B
Cleaning and Transporting the Printer
Proof Sign-off:
Yamanouchi _______
Grady _______
Cleaning the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2
Transporting the Printer . . . . . . . . . . . . . . . . . . . . . . . . B-3
B
R
Sun-G+ Rev.C
A5 size Appendix B
97/11/14 pass 0
Cleaning and Transporting the Printer B-1
Cleaning the Printer
To keep your printer operating at its best, you should clean it thoroughly
several times a year. Follow these steps:
1. Make sure the printer is turned off. Then remove any paper loaded in
the printer.
2. Remove the paper guide. If a pull tractor or an optional cut-sheet feeder
is installed, remove it.
3. Use a soft brush to carefully brush away all dust and dirt from the
outer case and paper guide.
4. If the outer case or paper guide is still dirty, clean it with a soft, clean
cloth dampened with mild detergent dissolved in water. Keep the
printer cover in place and lower the paper guide cover until it lies flat
on the top of the printer to prevent water from getting inside the
printer.
cCaution:
TNever use alcohols or thinners to clean the printer; these chemicals
can damage the printer components as well as the case.
TBe careful not to get water on the printer mechanism or electronic
components.
TDo not use a hard or abrasive brush.
TDo not spray the inside of the printer with lubricants; unsuitable
lubricants can damage the printer mechanism. Contact an EPSON
dealer if you think lubrication is needed.
L
Sun-G+ Rev.C
A5 size Appendix B
97/11/14 pass 0
B-2 Cleaning and Transporting the Printer
Transporting the Printer
If you need to transport your printer some distance, carefully repack it
using the original box and packing materials, as described below.
wWarning:
You will need to move the print head by hand to remove the ribbon
cartridge. If you have just used the printer, the print head may be hot; let
it cool for a few minutes before touching it.
1. Turn off the printer.
2. Unplug the power cord from the electrical outlet; then disconnect the
interface cable from the printer.
3. Remove any paper loaded in the printer, and remove the paper guide.
Pull out the paper separator from the paper guide.
4. If a pull tractor is installed, remove it as described on page 2-33. If any
options are installed, remove them and pack them in their original
boxes.
5. Make sure that the print head is not hot. Then remove the ribbon
cartridge as described in Chapter 1.
6. Remove the paper tension unit as described on page 2-23. Attach the
protective locking clips on both sides of the printer roller. Then install
the paper tension unit as described on page 2-34.
7. Make sure the tractor that comes with your printer is installed in the
front push position. See page 2-9 for instructions.
8. Replace the transportation screw using the screwdriver that came with
the printer.
9. Repack the printer, ribbon cartridge, paper guide, paper separator, and
power cord in the original packing materials and place them in the
printer’s original box.
B
R
Sun-G+ Rev.C
A5 size Appendix B
97/11/14 pass 0
Cleaning and Transporting the Printer B-3
Appendix C
Specifications
Proof Sign-off:
Yamanouchi _______
Grady _______
Printer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
Paper alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . C-7
Printable area . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
Safety approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . C-10
CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-10
Command Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-11
EPSON ESC/P control codes . . . . . . . . . . . . . . . . . . . C-11
IBM 2381 Plus emulation control codes . . . . . . . . . . . . . C-15
Character Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-16
International character sets for the Italic table . . . . . . . . . . C-25
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-1
Printer Specifications
Mechanical
Printing method: 9-pin impact dot matrix
Printing speed: High speed draft 500 cps at 10 cpi
maximum
Draft 380 cps at 10 cpi
Near letter quality 95 cps at 10 cpi
Printing direction: Bidirectional logic seeking for text and
graphics printing. Unidirectional text or
graphics printing can be selected using
software commands.
Line spacing: 1/6-inch or programmable in 1/216-inch
increments
Printable columns: 136 columns (at 10 cpi)
Resolution: Maximum 240 × 144 dpi (near letter quality)
Interfaces: One standard bidirectional, 8-bit, parallel
interface with IEEE 1284 nibble mode
support and one optional interface slot
Paper feed methods: Friction (front or top paper entry)
Push tractor (front or rear paper entry)
Pull tractor (front, bottom, or rear paper entry)
Push and pull tractor (additional tractor is
required for front push and pull tractor
combination)
Cut-sheet feeder (optional)
Roll paper holder (optional)
Paper feed speed: Continuous 5 inches/second
Intermittent 61 ms/line at 1/6-inch line
spacing
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-2 Specifications
Paper capacity: High-capacity cut-sheet feeder
up to 150 sheets of 82 g/m2 (22 lb) paper
up to 25 plain or bond envelopes
up to 30 airmail envelopes
up to 30 postcards
a stack of multi-part forms up to 15 mm
(0.59 inch) thick
Note:
The total thickness of the paper stack can be up
to 15 mm (0.59 inch).
Second-bin cut-sheet feeder
up to 50 sheets of 82 g/m2 (22 lb) paper
Note:
The total thickness of the paper stack can be up
to 5 mm (0.20 inch).
Buffer: 64KB or 0KB (selectable in the
default-setting mode or the EPSON
Remote! utility)
Built-in fonts: Bitmap fonts
EPSON Draft 10, 12, 15 cpi
EPSON Roman 10, 12, 15 cpi, proportional
EPSON Sans Serif 10, 12, 15 cpi, proportional
Barcode fonts
EAN-13, EAN-8, Interleaved 2 of 5, UPC-A,
UPC-E, Code 39, Code 128, POSTNET
Character tables: One Italic and 10 graphical character tables.
(19 graphical character tables are available
in some countries.) See page C-16 for more
information on the available character
tables.
Character sets: 13 international character sets
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-3
Reliability: Total print
volume 7.5 million lines
(except print head)
Print head life approx. 300 million
characters (Draft, 10 cpi,
14 dots/character)
Dimensions and weight: Height 257 mm (10.1 inches)
Width 639 mm (25.2 inches)
Depth 402 mm (15.8 inches)
Weight approx. 13 kg (28.8 lb)
Ribbon: Black ribbon cartridge (S015086)
Ribbon life 12 million characters
(Draft, 10 cpi, 14 dots/
character)
Electrical
120 V Model 220 to 240 V Model
Input voltage range 99 to 132 V 198 to 264 V
Rated frequency range 50 to 60 Hz
Input frequency range 49.5 to 60.5 Hz
Rated current 1.0 A (maximum 1.8 A
depending on the
character type)
0.5 A (maximum 0.9 A
depending on the
character type)
Power consumption Approx. 46W (ISO/IEC 10561 letter pattern)
This product is also designed for IT power systems with Phase to Phase
voltage 220 to 240 V.
Note:
Check the label on the back of the printer for the voltage of your printer.
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-4 Specifications
Environmental
Temperature Humidity
(without condensation)
Operation 5 to 35°C (41 to 95°F) 10 to 80% RH
Storage –30 to 60°C (–22 to 140°F) 0 to 85% RH
Paper
Note:
TUse recycled paper and envelopes only under normal temperature and
humidity conditions, as follows:
Temperature 15 to 25°C (59 to 77°C)
Humidity 30 to 60% RH
TDo not load paper that has been folded or is damaged, wrinkled, or curled.
Ordinary single sheets: front and top entry
Width 100 to 420 mm (3.9 to 16.5 inches)
Length Front: 148 to 420 mm (5.8 to 16.5 inches)
Top: 100 to 420 mm (3.9 to 16.5 inches)
Thickness 0.065 to 0.14 mm (0.0025 to 0.0055 inch)
Weight 52.3 to 90 g/m2 (14 to 24 lb)
Single-sheet multi-part
forms: front and top entry
Width 100 to 420 mm (3.9 to 16.5 inches)
Length Front: 148 to 420 mm (5.8 to 16.5 inches)
Top: 100 to 420 mm (3.9 to 16.5 inches)
Copies 1 original + up to 5 copies
Thickness 0.12 to 0.46 mm (0.0047 to 0.018 inch)
Weight 40 to 58 g/m2 (12 to 15 lb)
Binding Line glue at the top of form (both front and
top entry)
Single side line glue (front entry only)
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-5
Envelopes: top entry only
Size No. 6: 165 × 92 mm (6.5 × 3.6 inches)
No. 10: 241 × 105 mm (9.5 × 4.1 inches)
Thickness 0.16 to 0.52 mm (0.0063 to 0.0197 inch)
Weight 45 to 90 g/m2 (12 to 24 lb)
Postcards: front and top entry
Width 100 to 148 mm (3.9 to 5.83 inches)
Length Front: 148 mm (5.83 inches)
Top: 100 to 148 mm (3.9 to 5.83 inches)
Thickness 0.22 mm (0.0087 inch)
Weight 192 g/m2 (51 lb)
Continuous paper
(standard and multi-part): front, rear, and bottom entry
Width 101 to 406 mm (4.0 to 16.0 inches)
Length 101 to 559 mm (4.0 to 22.0 inches)
Copies 1 original + up to 5 copies
1 original + up to 6 copies
(front or bottom entry
with the pull tractor only)
Thickness Printable area 0.065 to 0.46 mm
(0.0025 to 0.018 inch)
Perforated edges up to 0.9 mm (0.035 inch)
Weight
(not multi-part) 52.3 to 82 g/m2 (14 to 22 lb)
Weight
(one sheet of multi-part) 40 to 58 g/m2 (12 to 15 lb)
Binding Point glue or paper staples on both sides
(front, bottom, or rear entry)
Point glue on only one side (rear entry only)
Note:
Because thick multi-part forms require a straight paper path, load them in
the front slot.
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-6 Specifications
Continuous paper
with labels: front and bottom entry
Label size 23.8 × 63.5 mm (15/16 × 2.5 inches) minimum
2.5 mm (0.1 inch) corner radius, minimum
Backing sheet width 101.6 to 406.4 mm (4.0 to 16.0 inches)
Backing sheet length
(one page) 101.6 to 559 mm (4.0 to 22.0 inches)
Backing sheet thickness 0.07 to 0.09 mm (0.0028 to 0.0035 inch)
Total thickness 0.16 to 0.19 mm (0.0063 to 0.0075 inch)
Label weight 68 g/m2 (17 lb)
Roll paper: rear entry with optional roll paper holder only
Width 216 ± 3 mm (8.5 ± 0.12 inch)
Thickness 0.07 to 0.09 mm (0.0028 to 0.0035 inch)
Weight 52 to 82 g/m2 (14 to 22 lb)
Paper alignment
Front entry
Printing starts at the arrow mark. The unprintable area is to the left of the
arrow mark.
margi2
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-7
Rear entry
Printing starts at “0” on the scale. The unprintable area is to the left of
the “0”.
Printable area
Single sheets, envelopes, and postcards:
A The minimum top margin is 4.2 mm (0.17 inch).
B The minimum left margin is 3.0 mm (0.12 inch).
The minimum right margin is 3.0 mm (0.12 inch).
The maximum width is 420 mm (16.5 inches) and
the maximum printable width is 345.4 mm (13.6 inches).
For single sheets wider than 351.4 mm (13.8 inches), the side margins
increase proportionally to match the width of the paper.
C The minimum bottom margin is 4.2 mm (0.17 inch).
margin
printable
area
AB
C
printable
area
A
B
C
B
a-1
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-8 Specifications
Continuous paper:
A The minimum top and bottom margins above and below the
perforation are 4.2 mm (0.17 inch) each.
B The minimum left and right margins are 13 mm (0.51 inch) each.
The maximum printable width is 345.4 mm (13.6 inches).
The maximum width is 420 mm (16.5 inches) and
the maximum printable width is 345.4 mm (13.6 inches).
For continuous paper wider than 351.4 mm (13.8 inches), the side margins
increase proportionally to match the width of the paper.
Roll paper:
A The minimum top margin is 4.2 mm (0.17 inch).
B The minimum left margin is 3.0 mm (0.12 inch).
The minimum right margin is 3.0 mm (0.12 inch).
The maximum printable width is 203.2 mm (8.0 inches).
printable
area
B
A
B
Aa-3
printable
area
AB
a-2
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-9
Safety approvals
120 V model:
Safety standards UL1950
CSA C22.2 No. 950
EMI FCC part 15 subpart B class B
CSA C108.8 class B
230 V model:
Safety standards EN 60950 (TÜV, NEMKO)
EMI EN 55022 (CISPR pub. 22) class B
AS/NZS 3548 class B
Acoustic noise: Approx. 55 dB (A) (ISO 7779 pattern)
CE marking
230 V model:
Low Voltage Directive 73/23/EEC EN 60950
EMC Directive 89/336/EEC EN 55022 Class B
EN 61000-3-2
EN 61000-3-3
EN 50082-1
IEC 801-2
IEC 801-3
IEC 801-4
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-10 Specifications
Command Lists
Your printer supports the following EPSON ESC/P control codes and
IBM 2381 Plus emulation control codes.
EPSON ESC/P control codes
Selecting an EPSON ESC/P printer in your software allows you to use
advanced fonts and graphics. See the ESC/P Reference Manual for details.
General operation:
ESC @, ESC U, ESC EM
Paper feeding:
FF, LF, ESC 0, ESC 2, ESC 3, ESC 1, ESC A, CR
Page format:
ESC ( C, ESC C, ESC C 0, ESC Q, ESC l, ESC ( c, ESC N, ESC O, ESC ( U
Print position motion:
ESC $, ESC ¥, ESC D, HT, ESC B, VT, ESC J
Font selection:
ESC k, ESC x, ESC P, ESC M, ESC g, ESC p, ESC 4, ESC 5, ESC E, ESC F,
ESC !
Font enhancement:
ESC W, DC4, SO, DC2, SI, ESC w, ESC G, ESC H, ESC T, ESC S, ESC -
Spacing:
ESC Space
Character handling:
ESC t, ESC ( t, ESC R, ESC %, ESC &, ESC :, ESC 6, ESC 7, ESC I
Bit image:
ESC K, ESC L, ESC Y, ESC Z, ESC ^, ESC *
Bar code:
ESC ( B
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-11
Barcode commands
Your printer has powerful barcode printing capabilities and includes the
following resident barcode fonts: EAN-13, EAN-8, Interleaved 2 of 5,
UPC-A, UPC-E, Code 39, Code 128, and POSTNET. See the barcode
commands below:
ESC ( B Select Barcode Printing
Format:
ASCII code:
Decimal:
Hexadecimal:
ESC
27
1B
(
40
28
B
66
42
m
m
m
n
n
n
Function:
ESC ( B n1 n2 k m s v1 v2 c data
n = (n1 + (256 × n2))
k: Select barcode
k = 0: EAN-13, 1: EAN-8, 2: Interleaved 2 of 5, 3: UPC-A,
4: UPC-E, 5: Code 39, 6: Code 128, 7: POSTNET
m: Module width (120 dpi)
m = 2: 2 dots, 3: 3 dots, 4: 4 dots, 5: 5 dots
s: Space adjustment value
-3 ≤ s ≤ 3 (1/240-inch units)
v1, v2: Bar length
v1 + v2 × 256 (1/72-inch units)
Note:
TThe v1 and v2 values are ignored when POSTNET is selected.
TThe long bar length of POSTNET is always 0.125 inch; the short bar length
is always 0.050 inch.
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-12 Specifications
c: Control flag
Bit 0 = Check digit
0: The printer does not add a check digit.
1: The printer adds a check digit.
Bit 1 = Human readable character (HRC)
0: The printer adds the HRC.
1: The printer does not add the HRC.
Bit 2 = Position of flag character (for EAN-13 and UPC-A only)
0: Center
1: Under
Bits 3−7 = Not used
Barcode data
Barcode data corresponds to the barcode symbology. The data number of
each barcode type is constant. The barcode is printed only if the following
valid characters are set.
Barcode type Number of valid
characters 1 (HEX) Number of valid
characters 2 (HEX)
EAN-13
EAN-8
Interleaved 2 of 5
UPC-A
UPC-E
Code 39
Code 128
POSTNET
0D
8
2 to FF
0C
0C or 8
1 to FF
2 to FF
6 or 0A or 0C
0C
7
2 to FF
0B
0B or 7
1 to FF
2 to FF
5 or 9 or 0B
Number of valid characters 1: Control flag c b0=0
Number of valid characters 2: Control flag c b0=1
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-13
The valid data for each barcode type is described below. If invalid data is
included in the barcode data string, the barcode is not printed.
Barcode type Barcode data
EAN-13
EAN-8
UPC-A
UPC-E
Interleaved 2 of 5
POSTNET
Code 39
Code 128
0-9 (Hex 30-39)
0-9 (Hex 30-39)
0-9 (Hex 30-39)
0-9 (Hex 30-39)
0-9 (Hex 30-39)
0-9 (Hex 30-39)
0-9 (Hex 30-39), (Hex 41-5A), (Hex 20, 24, 25, 2B, 2D,
2E, 2F)
Set A, Set B, Set C
The following conditions are required for barcode printing:
TBarcode printing is always performed unidirectionally. However,
when it is mixed with raster bit image data, neither barcode nor raster
bit image data is printed.
TA barcode is not printed when part of the barcode extends beyond
the right margin.
TWhen barcode data and text data are mixed in a data sequence,
barcodes and text are printed in the same place.
TThe start and stop (*) characters of Code 39 are added to human
readable characters.
TThe initial data of Code 128 (Set A, B, or C) is identified as the first
data of Code 128, and must be hexadecimal (41, 42, and 43,
respectively).
TWhen Code 128 Set C and Interleaved 2 of 5 are selected, barcode
data requires an even number data string. However, if an odd
number string is sent, a 0 is automatically added, making it an even
number data string.
TThe barcode print start position (except for POSTNET) is always
7/72 inch above the baseline.
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-14 Specifications
IBM 2381 Plus emulation control codes
This printer emulates the IBM Proprinter using the commands below. For
detailed information, see the IBM 2381 Plus reference manual.
General operation:
NUL, DC3, ESC j, BEL, CAN, DC1, ESC Q, ESC [ K, ESC U, ESC [ F
Paper feeding:
FF, LF, ESC 5, ESC A, ESC 0, ESC 1, ESC 2, ESC 3, CR, ESC ]
Page format:
ESC C, ESC C0, ESC X, ESC N, ESC O, ESC 4
Print position motion:
ESC d, ESC R, ESC D, HT, ESC B, VT, ESC J
Font selection:
DC2, ESC P, ESC :, ESC E, ESC F, ESC I, ESC [d, ESC [I
Font enhancement:
DC4, SO, ESC SO, ESC W, ESC [ @, SI, ESC SI, ESC G, ESC H, ESC T,
ESC S, ESC -, ESC _
Spacing:
BS, SP
Character handling:
ESC 6, ESC 7, ESC [ T, ESC ^, ESC ¥
Bit image:
ESC K, ESC L, ESC Y, ESC Z
Barcode:
ESC [f, ESC [p
Download:
ESC = (draft mode only)
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-15
Character Tables
You can select the character tables shown in this section using the
printer’s default-setting mode or with software commands.
Note:
TMost of the character tables are the same as the PC 437 table for hex codes 00
through 7F; for these tables, only the characters for hex codes 80 through FF
are shown.
TThe character tables with an asterisk (*) after the table name are available
only in some countries.
You can choose between the two IBM character tables shown below when
you select the IBM 2381 Plus emulation in the default-setting mode as
described in Chapter 5. (When you select Table 1, hex codes 00 to 1FH and
80 to 9FH are replaced; when you select Table 2, hex codes 00 to 1FH are
replaced.)
Table 1 Table 2
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-16 Specifications
PC 437 (USA, Standard European)
PC 850 (Multilingual) PC 860 (Portuguese)
a-7
a-8, a-9
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-17
PC 863 (Canadian-French) PC 865 (Norwegian)
PC 861 (Icelandic) BRASCII (Brazilian Portuguese)
a-10, a-11
a-12, a-13
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-18 Specifications
Abicomp (Brazilian Portuguese) ISO Latin 1
Roman 8
a-14, a-15
a-16, a-17
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-19
PC 437 Greek (Greek)* PC 869 (Greek)*
ISO 8859-7 (Latin/Greek)* PC 853 (Turkish)*
a-18, a-19
a-20, a-21
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-20 Specifications
PC 857 (Turkish)* ISO Latin 1T (Turkish)*
PC 855 (Cyrillic)* PC 866 (Russian)*
a-22, a-23
a-24, a-25
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-21
PC 852 (East European)* MAZOWIA (Polish)*
Code MJK (CSFR)* Bulgaria*
a-26, a-27
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-22 Specifications
Estonia* PC 774 (LST 1283:1993)*
ISO 8859-2*
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-23
PC 866 LAT. (Latvian)*
PC 866 UKR (Ukranian)* Italic
No character is available
for hex code 15 in the
Italic table.
L
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
C-24 Specifications
International character sets for the Italic table
You can select one of the following eight international character sets for
the Italic character table shown below using the default-setting mode or
the ESC R command. For example, when you select “Italic France,” the
characters in the “France” row are used in the Italic character table.
You can select one of the following seven additional sets only with the
ESC R command.
a-31
a-32
C
R
Sun-G+ Rev.C
A5 size Appendix c
97/11/13 pass 0
Specifications C-25
Appendix D
Customer Support Information
Contacting Customer Support . . . . . . . . . . . . . . . . . . . . . D-2
For North American Users . . . . . . . . . . . . . . . . . . . . . . . D-2
For United Kingdom and the Republic of Ireland Users . . . . . . D-4
Enquiry Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
Faxon EPSON . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-5
EPtec - Bulletin Board Service for latest drivers
and utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-5
World Wide Web . . . . . . . . . . . . . . . . . . . . . . . . . . D-5
For Australian Users . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
EPSON FAXBACK . . . . . . . . . . . . . . . . . . . . . . . . . D-6
EPSON Bulletin Board System . . . . . . . . . . . . . . . . . . . D-6
Internet URL http://www.epson.com.au . . . . . . . . . . . . D-6
Your dealer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6
EPSON Helpdesk . . . . . . . . . . . . . . . . . . . . . . . . . . D-7
For Singapore Users . . . . . . . . . . . . . . . . . . . . . . . . . . . D-7
For Hong Kong Users . . . . . . . . . . . . . . . . . . . . . . . . . . D-7
Internet home page . . . . . . . . . . . . . . . . . . . . . . . . . D-8
Electronic bulletin board system . . . . . . . . . . . . . . . . . D-8
Technical support hotline . . . . . . . . . . . . . . . . . . . . . D-8
For Philippines Users . . . . . . . . . . . . . . . . . . . . . . . . . . D-8
Proof Sign-off:
Yamanouchi _______
Grady _______ R
D
Sun-G+ Rev.C
A5 size Appendix D
97/11/13 pass 0
Customer Support Information D-1
Contacting Customer Support
If your printer is not operating properly and you cannot solve the
problem using the troubleshooting information in Chapter 7, contact
customer support services for assistance. See the section for your country
below.
We will be able to help you much more quickly if you give us the
following information:
Printer model:
Serial number of your printer:
(The serial number label is on the back of the printer.)
Brand and model of your computer:
Printer software version:
(Click the About button in your printer driver.)
Windows version (for example, NT, 95, or 3.1):
Software application(s) you normally use with the printer and their
version number(s):
For North American Users
If you purchased your printer in the United States or Canada, EPSON
provides customer support through the following services:
Electronic support services
Service Access
World Wide Web From the Internet, you can reach EPSON’s home
page at http://www.epson.com.
EPSON Internet FTP Site If you have Internet FTP capability, use your Web
browser (or other software for FTP downloading) to
log onto ftp.epson.com with the user name
anonymous and your e-mail address as the password.
EPSON Download Service You can call the EPSON Download Service at
(800) 442-2007. Set your communications software to
8 data bits, 1 stop bit, no parity. Modem speed can
be up to 28.8 Kbps.
EPSON Forum on
CompuServe®Members of CompuServe can type GO EPSON at the
menu prompt to reach the Epson America Forum. For
a free introductory CompuServe membership, call
(800) 848-8199 and ask for representative #529.
L
Sun-G+ Rev.C
A5 size Appendix D
97/11/13 pass 0
D-2 Customer Support Information
Automated telephone services
Service Access
EPSON SoundAdviceFor pre-recorded answers to commonly asked
questions about EPSON products 24 hours a day,
seven days a week, call (800) 442-2110.
EPSON FaxAdviceAccess EPSON’s technical information library by
calling (800) 442-2110. You must provide a return fax
number to use this service.
EPSON Referral Service For the location of your nearest Authorized EPSON
Reseller or Customer Care Center, call (800) 442-2110.
EPSON also provides technical support and information on the
installation, configuration, and operation of EPSON products. Dial
(800) 922-8911, (310) 782-2600 (U.S.), or (905) 709-9475 (Canada), 6 A.M.
to 6 P.M., Pacific Time, Monday through Friday.
Before you call, please have the following information ready:
TProduct name
TProduct serial number
TComputer configuration
TDescription of the problem
You can purchase ink cartridges, paper, manuals, accessories, and parts
from EPSON Accessories at (800) 873-7766 (U.S. sales only). In Canada,
please call (800) 873-7766 for dealer referral.
Note:
If you need help using software with an EPSON product, see the documentation
for that program for technical support information.
R
D
Sun-G+ Rev.C
A5 size Appendix D
97/11/13 pass 0
Customer Support Information D-3
For United Kingdom and the Republic of Ireland
Users
If you purchased your printer in the UK or the Republic of Ireland,
Epson (UK) Limited provides a range of customer services and technical
support.
Note:
For customers in the Republic of Ireland, please use the correct dialing codes
when dialing the UK telephone numbers listed in the following sections. For
example the Enquiry Desk fax number, 01442 227271, should be dialed as
0044 1442 227271 from the Republic of Ireland.
Enquiry Desk
The Enquiry Desk team can be contacted by calling 0800 220546 in the UK
or 1 800 409132 from the Republic of Ireland, by faxing 01442 227271, or
via the Internet at info@epson.co.uk. They can provide the following
information:
TInformation and literature on new EPSON products (also available
from Faxon EPSON)
TWhere to purchase genuine EPSON consumables, accessories and
options
Customer Support
Our Customer Support team can provide the following services:
TTechnical information on installing, configuring, and operating
your EPSON products
TArranging for faulty EPSON products to be repaired within the
warranty period
For information on contacting our Customer Support team, please see
the Service and Support Information booklet that came with your EPSON
product.
If this booklet is not available, details can be found on Faxon EPSON
faxback service, EPtec Bulletin Board Service or on EPSON’s World Wide
Web site. See below for details.
L
Sun-G+ Rev.C
A5 size Appendix D
97/11/13 pass 0
D-4 Customer Support Information
Faxon EPSON
Contact Faxon EPSON Faxback Service for:
TLiterature and specifications on the latest EPSON products
TSupport information including troubleshooting tips, switch settings
and driver information
To use Faxon EPSON, call 01442 227332 using a touch-tone phone. You
will be asked to follow a simple routine to register your document request
and once you have entered your telephone and fax numbers, Faxon
EPSON will fax a copy of the document catalogue to your fax machine.
When you have found the documents that you need in the catalogue, call
Faxon EPSON again and enter the document ID numbers. The documents
will be faxed to you automatically.
EPtec - Bulletin Board Service for latest drivers and
utilities
You can call the EPSON Bulletin Board Service on 01442 227479. No
membership is required. Make sure that your communications software
is set to 8 data bits, 1 stop bit, no parity bit, ANSI terminal mode
emulation and a modem speed of up to 28.8 Kbps. Downloading
protocols supported include Xmodem, Ymodem and Zmodem. See the
documentation that came with your communications software and
modem for more information.
When you first connect to the Bulletin Board Service, you will be asked
for your name, company name, phone number and a password (which
you can invent yourself).
World Wide Web
If you can connect to the Internet and have a Web browser, you can access
EPSON’s World Wide Web site at http://www.epson.com. Here you will
find information on the latest EPSON products, software drivers, and
answers to frequently asked questions.
R
D
Sun-G+ Rev.C
A5 size Appendix D
97/11/13 pass 0
Customer Support Information D-5
For Australian Users
EPSON Australia wishes to provide you with a high level of Customer
Service. As well as this User’s Guide, we provide the following sources
for obtaining information:
EPSON FAXBACK
EPSON FAXBACK will fax you the latest specifications and pricing for
most EPSON products offered in Australia. There is also technical
information including details of the latest software and drivers available.
Phone (02) 9903 9075 and the system will guide you through a number
of choices before faxing the information to your fax machine.
EPSON Bulletin Board System
This is where you can download the latest software and drivers. Visit
the BBS to check out the latest versions. If you have a modem, phone
(02) 9417 5090.
Internet URL http://www.epson.com.au
Access the Epson Australia World Wide Web pages. Worth taking your
modem here for the occasional surf! You can get the same information as
offered on the EPSON FAXBACK and the EPSON Bulletin Board plus
more.
Your dealer
Don’t forget that your dealer can often help identify and resolve
problems. The dealer should always be the first call for advice on
problems. They can often solve problems quickly and easily as well as
give you advice on the next step to take.
L
Sun-G+ Rev.C
A5 size Appendix D
97/11/13 pass 0
D-6 Customer Support Information
EPSON Helpdesk
EPSON Helpdesk is provided as a final backup to make sure our clients
have access to advice. Operators on the Helpdesk can aid you in
diagnosing hardware and software problems. They can also advise you on
the latest EPSON products and where the nearest dealer or service agent
is located. Many types of queries are answered here.
The Helpdesk numbers are:
Phone: (02) 9903 9040
Fax: (02) 9903 9189
We encourage you to have all the relevant information on hand when you
ring. The more information you prepare, the faster we can help solve the
problem. This information includes the User’s Guide for your EPSON
product, type of computer, operating system, application programs, and
any other information you feel is required.
For Singapore Users
Contact the telephone and fax numbers below.
Phone: (065) 337-7911
Fax: (065) 334-1185
For Hong Kong Users
To obtain technical support as well as other after-sales services, users are
welcome to contact EPSON Hong Kong Limited.
R
D
Sun-G+ Rev.C
A5 size Appendix D
97/11/13 pass 0
Customer Support Information D-7
Internet home page
EPSON Hong Kong has established a local home page in both Chinese
and English on the Internet to provide users with the following
information:
TProduct information
TAnswers to Frequently Asked Questions (FAQs)
TLatest versions of EPSON printer drivers
Users can access our World Wide Web home page at
http://www.epson.com.hk.
Electronic bulletin board system
An electronic bulletin board system (BBS) is also available to obtain
printer information and the latest versions of printer drivers. You can log
onto the following number for the BBS service:
BBS: (852) 2827-4244
Technical support hotline
You can also contact our technical staff at the telephone and fax numbers
below.
Phone: (852) 2585-4399
Fax: (852) 2827-4383
For Philippines Users
To obtain technical support as well as other after sales services, users are
welcome to contact the EPSON Philippines Representative Office at the
telephone and fax numbers below.
Phone: (632) 813-6552
Fax: (632) 813-6545
BBS: (632) 814-0595
L
Sun-G+ Rev.C
A5 size Appendix D
97/11/13 pass 0
D-8 Customer Support Information
Glossary
ASCII
American Standard Code for Information Interchange. A standardized
coding system for assigning numerical codes to letters and symbols.
auto line feed
When this setting is turned on using the default-setting mode or the
EPSON Remote! utility, each carriage return (CR) code is automatically
followed by a line feed (LF) code.
bidirectional printing
Printing in which the print head prints in both directions (bidirectionally).
This increases the print speed but may reduce precise vertical alignment.
Bidirectional printing is the printer’s standard printing mode. See also
unidirectional printing.
buffer
The portion of the printer’s memory used to store data before it is printed.
character table
A collection of letters, numbers, and symbols that constitute the set of
characters used in a particular language.
characters per inch (cpi)
A measure of the size of text characters. See also pitch.
continuous paper
Paper that has sprocket-feed holes on both sides, is perforated between
pages, and is supplied in a folded stack. Also called fanfold paper.
control code
A special code used to control a printer function such as a carriage return
or line feed.
cpi
See characters per inch.
cut-sheet feeder
An optional, detachable device that automatically feeds single sheets of
paper into the printer.
data dump
See hex dump.
default
A value or setting that takes effect when the equipment is turned on,
reset, or initialized. Also known as a factory setting.
Proof Sign-off:
Yamanouchi _______
Grady _______ R
Sun-G+ Rev.C
A5 size Glossary
97/11/14 DR, pass 1
Glossary 1
dithering
A halftoning method in which dots are printed in a predetermined pattern
to simulate a shade or tone. Dithering works best for images with solid
colors, such as charts and graphs. See also halftoning.
dot matrix
A method of printing in which each letter or symbol is formed by a
pattern (matrix) of individual dots.
draft
The print mode used by your printer when you select Draft as the font.
The Draft font uses fewer dots per character for faster printing. See also
high-speed draft and near letter quality.
driver
See printer driver.
ESC/P
Abbreviation for EPSON Standard Code for Printers, the system of
commands your computer uses to control your printer. It is standard for
all EPSON printers and supported by most application software for
personal computers.
fanfold paper
See continuous paper.
font
A style of type designated by a name such as Roman or Sans Serif.
form feed (FF)
A control panel button and control code that advances the paper to the
next top-of-form position.
halftoning
A method of using dot patterns to represent an image. Halftoning makes
it possible to produce varying shades of gray using only black dots, or a
nearly infinite array of colors using only a few colors of dots.
hex dump
A troubleshooting feature that helps identify the cause of communication
problems between the printer and the computer. When the printer is in
hex dump mode, it prints each code that it receives in hexadecimal
notation and as ASCII characters. Also called data dump.
high-speed draft
A draft printing mode you can select using the printer’s default-setting
mode or the EPSON Remote! utility. High-speed draft uses a minimum
number of dots per character to produce extremely high-speed printing.
See also draft and near letter quality.
L
Sun-G+ Rev.C
A5 size Glossary
97/11/14 DR, pass 1
2 Glossary
interface
The connection (via a cable) between the computer and the printer over
which print data is transmitted to the printer.
landscape
Printing that is oriented sideways on the page. This orientation gives you
a page that is wider than it is high and is useful for printing spreadsheets.
See also portrait.
line feed (LF)
A control panel button and control code that advances the paper one line
space.
micro adjust
A printer feature that allows you to precisely adjust the tear-off and
top-of-form positions.
near letter quality (NLQ)
The print mode used by your printer when you select Roman or Sans Serif
as the font. Printing with near letter-quality fonts provides better
readability and appearance at a reduced print speed. See also draft and
high-speed draft.
paper positions
There are three paper positions for continuous paper printing: standby,
tear-off, and top-of-form. For single sheet printing, there is only the
top-of-form position. See also standby position, tear-off position, and
top-of-form position. For detailed information on these positions, see “Paper
positions” on page 5 of the Glossary.
pitch
The size of the font, which is measured in the number of characters per
inch (cpi). The standard is 10 cpi. See also characters per inch.
platen
The black roller that provides a backing for the paper during printing.
portrait
Printing that is oriented upright on the page (as opposed to landscape, in
which printing is sideways on the page). This is the standard orientation
for printing letters or documents. See also landscape.
printable area
The area of a page on which the printer can print. It is smaller than the
physical size of the page due to margins.
printer driver
A software program that runs, or “drives,” a printer. Printer drivers send
commands to your printer to tell it how to print your print job.
R
Sun-G+ Rev.C
A5 size Glossary
97/11/14 DR, pass 1
Glossary 3
proportional font
A font whose characters take up varying amounts of horizontal space
depending on the width of the character. Thus the uppercase M takes up
more horizontal space than the lowercase l.
reset
To return a printer to its default settings.
resolution
A measure of the amount of detail that can be represented. Resolution
of printed images is measured using the number of dots per inch (dpi).
self test
A method used to check the operation of the printer. When you run the
self test, the printer prints the characters stored in its ROM (Read Only
Memory).
standby position
The position of your continuous paper when it is attached to the tractor
but not loaded in the printer. See also page 5 of the Glossary.
Tear Off Bin button
A control panel button that feeds the perforation of continuous paper to
the tear-off position, and when pressed again, feeds the paper back to the
top-of-form position.
tear-off position
The position of your continuous paper when you finish printing if auto
tear-off mode is on or if you press the Tear Off/Bin button. Using the
micro adjust feature, you can adjust the tear-off position so that the
paper’s perforation is aligned with the printer’s tear-off edge. See also
page 5 of the Glossary.
top-of-form position
The position on the paper that the printer recognizes as the first printable
line. This is the default top margin position. See also page 5 of the
Glossary.
unidirectional printing
Printing in which the print head prints in one direction only.
Unidirectional printing is useful for printing graphics because it provides
precise vertical alignment. You can select unidirectional printing using the
printer’s default-setting mode or the EPSON Remote! utility. See also
bidirectional printing.
L
Sun-G+ Rev.C
A5 size Glossary
97/11/14 DR, pass 1
4 Glossary
Paper positions
Standby position
In the standby position, your paper is attached to the printer but is not
inside the printer.
Tear-off position
Tear off your printed document at the printer’s tear-off edge.
Top-of-form position
The letters ABC above are printed at the top-of-form position.
new13,12
1-1
g-e
R
Sun-G+ Rev.C
A5 size Glossary
97/11/14 DR, pass 1
Glossary 5
Index
A
Accessing,
printer driver. See Printer driver.
EPSON Status Monitor 2, 6-4
Adjusting
tear-off position, 2-41–42
top-of-form position, 2-37–38
Advancing to the tear-off edge,
2-40–42
Aligning vertical line, 7-17
Attaching
front paper guide, 2-13
paper guide, 1-11–12
paper separator, 1-11–12
printer cover, 1-11
Auto tear-off mode, 2-41, 5-5
B
Background monitoring, 6-11–12
Beep pattern, 7-2–3. See also Buzzer.
Bin, A-10. See also Tear Off/Bin
button.
Built-in font, 5-2–5
Buttons, inside front cover
Buzzer, 5-7
C
Center support, A-6
Choosing a place for the printer, 1-4
Cleaning the printer, B-2
Command lists, C-11–15
Connecting the printer, 1-14–15
Continuous paper
multi-part forms, 2-5–6
printing, 4, 2-1–42
positioning, 1-5
problems, 7-8
with labels, 2-7–8
Control panel, inside front cover,
5-2–9
Cut-sheet feeder
installing, A-4–5
loading paper, A-6–9
selecting the paper source, A-10
Switching between continuous
paper printing, A-11
D
Default-setting mode, 5-3
changing, 5-8–9
Default settings, 5-3–9
Double-bin cut-sheet feeder, A-4. See
also cut-sheet feeder.
Double-strike mode, 2-6
E
Edge guides, 2-13, inside back cover
ENERGY STAR, 13
EPSON ESC/P control codes,
C-11–14
EPSON Remote! utility, 4-21
EPSON Status Monitor 2, 4-2, 6-2–12
accessing, 6-4
installing, 6-3
window, 6-4–9
Error indicators, 7-2–3
Proof Sign-off:
Yamanouchi _______
Grady _______ R
Sun-G+ Rev.c
A5 size Index
97/11/14 pass 0
IN-1
F
Font
button, inside front cover
light, inside front cover
selecting, 5-2–3
Front
edge guides, 3-11, inside back
cover
paper guide, 2-9, 2-10, 3-11,
inside back cover
push tractor, 5, 2-9–16
slot, 6, 9, 3-2, 3-10–12
G
Guide
ribbon,1-4
paper, 1-11, inside back cover
H
Hex dump, 7-19–20
High-capacity cut-sheet feeder, A-2,
A-4. See also cut-sheet feeder.
High-speed draft setting, 5-7
High-speed printing, 1. See also
High-speed draft setting.
I
IBM 2381 Plus emulation codes, C-15
Installing
EPSON Status Monitor 2, 6-3
front paper guide, 2-13
front push tractor, 2-9–10
interface card, A-17–18
paper tension unit, 2-34
printer cover, 1-11
printer driver, 1-15. See also
printer driver.
ribbon cartridge, 1-6–11
roll paper holder, A-14
tractor in the pull position,
2-23–24
Interface cards, A-3,
installing, A-17–18
International character sets, C-25
L
Levers
Paper release, 2, 2-3–4. See also
Paper release lever.
Paper selection, A-9
Paper set, A-8
Paper thickness, 2-2–3. See also
Paper thickness lever.
Paper type, A-8
LF/FF button, inside front cover
Lights, inside front cover
Load/Eject button, inside front cover
Loading
continuous multi-part forms,
2-5–6
continuous paper with labels,
2-7–8
envelopes, 3-6–7
paper onto
front push tractor, 2-10–14
rear push tractor, 2-17–20
pull tractor, 2-24–29
postcards, 3-7
single-sheet multi-part forms,
3-4–5
single sheets in
front paper slot, 3-10–12
top paper slot, 3-8–10
K
Knob, 7-16, inside back cover
ribbon-tightening, 1-8
L
Sun-G+ Rev.c
A5 size Index
97/11/14 pass 0
IN-2
M
Micro adjust
feature, 3
mode, 2-37, 2-41
Monitoring Preferences, 6-10–12
O
Operate button, inside front cover
Options, 10, A-2–18
P
Paper entry slots, 6, 3-2
Paper guide, inside back cover
attaching, 1-11–12
cover, 1-12, inside back cover
cut-sheet feeder, A-7
Paper Out light, inside front cover
Paper paths, 2–10,
Paper release lever, 2, inside back
cover
setting, 2-3–4
Paper selection lever, A-9
Paper set lever, A-8
Paper stacker, A-7
Paper tension unit, inside back cover
installing, 2-34
removing, 2-23
Paper thickness lever, inside back
cover
setting, 2-2–3
Paper type lever, A-8
Paper separator, inside back cover
attaching, 1-11–12
Pause
button, inside front cover
light, inside front cover
Pitch
button, inside front cover
light, inside front cover
selecting, 5-2–3
Plastic ribbon cover, 2-38
Plugging in the printer, 1-13
Printer cover, inside back cover
installing,1-11
removing, 1-7
Printer driver
accessing,
from NT 3.5x, 4-17–19
from NT 4.0, 4-12–14
from Windows 3.1, 4-8–10
from Windows 95, 4-3–5
installing,
for DOS, 1-20
for NT 3.5x, 1-19
for NT 4.0, 1-15–18
for Windows 3.1, 1-19
for Windows 95, 1-15–18
settings,
for DOS, 1-20
for NT 3.5x, 4-19–20
for NT 4.0, 4-14–16
for Windows 3.1, 4-10–11
for Windows 95, 4-5–8
Printer parts, inside back cover
Printer software, 4-2
Printer Status window, 6-9–10
Print head caution symbol, 12
Printing on
continuous paper, 2-1–40
continuous paper with labels,
2-7–8
continuous multi-part forms,
2-5–6
envelopes, 3-6–7
postcards, 3-7
single sheets, 3-1–12
single-sheet multi-part forms,
3-4–6
Pull tractor, 5-6, 2-22–34, A-2
Push and pull tractor combination,
7, 2-30–33
Push tractor, 4-5
R
Sun-G+ Rev.c
A5 size Index
97/11/14 pass 0
IN-3
R
Rear push tractor, 5, 2-17–22
Removing
continuous paper with labels, 2-8
front paper guide, 2-9
front push tractor, 2-16
paper tension unit, 2-23
printed document from
front push tractor, 2-14–15
rear push tractor, 2-21–22
printer cover, 1-7
pull tractor, 2-33
roll paper, A-16
Ribbon cartridge, 10
installing, 1-6–11
replacing, 1-6–11
Ribbon cover, 2-38
Ribbon guide, 1-8
Ribbon installation position, 1-7
Ribbon-tightening knob, 1-8
Roll paper holder, A-3, A-12–16
assembling, A-12
installing, A-13
loading roll paper, A-14
removing, A-16
S
Safety instructions, 11
Screwdriver, 1-2–3, B-3
Second-bin cut-sheet feeder, A-2, A-4
Selecting,
built-in font, 5-2–3
pitch, 5-2–3
Self test, 7-18–19
Separator
paper, 1-11
ribbon cartridge, 1-8
Setting
paper release lever, 2-2–3
paper thickness lever, 2-3–4
Shield plate, A-17, inside back cover
Single sheets
printing, 8, 3-1–12
problems, 7-6
Specifications, C-2–25
CE marking, C-10
character tables, C-16–25
command lists, C-11–15
electrical, C-4
environmental, C-5
mechanical, C-2–4
paper, C-5–7
paper alignment, C-7
printable area, C-8–9
safety approval, C-10
Status Monitor 2 utility, 4-2, 6-2–12
Switching
to continuous paper, 2-36, A-11
to single sheets, 2-35–36
to single sheets in the cut-sheet
feeder, A-11
T
Tear off
adjusting, 2-41–42
edge, 2-15, 2-42
feature, 2
position, 2-40–42
problems, 7-10
Tear Off/Bin
button, inside front cover, 2-40
lights, inside front cover
Top-of-form
adjusting, 2-37–39
position, 2-37
problems, 7-9
Top (paper) slot, 8, 3-2, 3-8–10
Tractor
combination, 2-30-33
front push, 2-9–16
pull, 2-22–34
rear push, 2-17–22
Transportation screw, 1-3, B-3
Transporting the printer, B-3
L
Sun-G+ Rev.c
A5 size Index
97/11/14 pass 0
IN-4
Troubleshooting, 7-2–19
continuous paper loading or
feeding problems, 7-8
error indicators, 7-2–3
power supply problems, 7-5
single-sheet paper loading or
feeding problems, 7-6–7
tear-off position problems, 7-10
top-of-form position problems,
7-9
U
Unpacking the printer, 1-2
Using
front push tractor, 2-9–16
rear push tractor, 2-17–22
pull tractor, 2-22–34
push and pull tractor
combination, 2-30–33
Utility
EPSON Remote!, 4-21
EPSON Status Monitor 2, 4-2,
V
Vertical line, aligning, 7-17
R
Sun-G+ Rev.c
A5 size Index
97/11/14 pass 0
IN-5
