Ericsson Wi Fi 20000003 2.4 GHz WLAN Access Radio Module 3 User Manual PM B2CC043AA C Manual IIa

Download:
Mirror Download [FCC.gov]
Document ID	687042
Application ID	lHZVXv1zxfkb6+L2O9DsdQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.83kB (47937 bits)
Date Submitted	2006-07-27 00:00:00
Date Available	2006-07-27 00:00:00
Creation Date	2006-07-24 10:35:49
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2006-07-24 10:35:49
Document Title	Microsoft Word - PM-B2CC043AA-C_Manual_IIa.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	mdubois

B2CC043AA-C
B2CC043AA-C Product Manual
2.4 GHz WLAN Access Radio Module 3
Document Date:
Document Number:
Document Version Number:
Document Status:
May 30 2006
PM-B2CC043AA-C
Release
© Copyright 2005 by BelAir Networks.
All rights reserved..
Page 1 of 14
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
May 30 2006
Page 2 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
Contents
About this Document ....................................................................... 3
Introduction...................................................................................... 4
Conditions of Use ............................................................................. 5
Module Installation and Service..................................................... 7
Final Product Requirements........................................................... 8
Regulatory Statements .................................................................. 11
About this Document
This document is a product manual for the B2CC043AA-C 2.4 GHz WLAN
Access Radio Module 3, including its limitations on use in any product
marketed or offered for sale. It is intended as a supplement to training and
documentation by BelAir Networks Inc. or its authorized agents.
May 30 2006
Page 3 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
Introduction
The B2CC043AA-C (hereafter referred to as “the module”) is a 2.4 GHz radio
module compatible with the IEEE 802.11 standard for Wireless LAN operation.
It is designed to be interoperable with WLAN products which are based on
Direct Sequence Spread Spectrum (DSSS) radio technology.
The module contains a complete 802.11b/g radio and Medium Access Control
(MAC) protocol engine which allows implementation of an 802.11b/g access
point (AP).
The module is not intended for stand-Clone operation. It will only be marketed
as a complete product, in conjunction with a package, DC power supply and
antenna (hereafter referred to as “the product” or the “final product”).
Since the module has a BelAir networks proprietary digital interface, it cannot
be directly connected to any standard telecommunications or computer devices.
It can only be used with final products designed and authorized specifically for
that purpose.
May 30 2006
Page 4 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
Conditions of Use
General Conditions of Use
This manual is intended to supplement training provided by BelAir Networks or
authorized parties. The module B2CC043AA-C is only intended for use in
BelAir Networks products and is not for sale to the general public as a standClone module.
Please read this entire document, including the Regulatory Statements section
before attempting to install or operate the module.
Warning:
Any use of B2CC043AA-C in any manner which is not
expressly specified within this manual or specifically approved by BelAir
Networks or its authorized agents will void the user’s right to operate this
module, and is expressly forbidden by BelAir Networks. This includes any
modification of the module, installation of the module in a configuration or used
with an antenna which is not expressly listed in this document or approved by
BelAir Networks.
List of Approved Final Products
The B2CC043AA-C module is only approved for use in the following BelAir
Networks products:
•
BelAir200. See BelAir200 documentation for complete manufacturing
instructions.
•
BelAir100. See BelAir100 documentation for complete manufacturing
instructions.
•
BelAir50c. See BelAir50c documentation for complete manufacturing
instructions.
Operation of the module within the products expressly listed above is required
to ensure compliance to all FCC and Industry Canada regulations. Any
modification of the module, or its use in any configuration not expressly listed
above may void the user’s right to operate this module.
May 30 2006
Page 5 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
Country of Use
B2CC043AA-C is certified with limited modular approval for use as an
Intentional Radiator in the United States as device: FCC ID: RAR20000003
and in Canada as IC: 4674A-20000003. Please read all regulatory statements at
the end of this document before any attempt to install or operate this module.
The module is only certified for operation in the United States and Canada.
Before attempting to install and operate this module in any other country,
contact BelAir Networks for approval.
Module Labeling
One or more labels are applied to the module during manufacture, including a
label which identifies the FCC and Industry Canada identification numbers. Do
not attempt to remove any labels from the module.
May 30 2006
Page 6 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
Module Installation and Service
Installation into a Product
The module shall only be installed by a technician trained by BelAir Networks
or its authorized agents. It should only be installed into an approved product
(see above) following all manufacturing and service procedures for that product.
The module should only be installed into a final product in a manufacturing or
service depot site.
Caution: B2CC043AA-C is an electro-static discharge (ESD) sensitive device.
All appropriate ESD measures must be taken when handling the module.
Failure to employ appropriate ESD protection may damage the module.
Module Service
The module is not intended as a field-serviceable unit. It contains no fieldreplaceable or field-serviceable parts, or any external adjustable mechanisms.
The module should only be serviced in a manufacturing or service depot site
approved by BelAir Networks or its authorized agents.
May 30 2006
Page 7 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
Final Product Requirements
The requirements below apply to any final product in which the B2CC043AA-C
module is installed.
Antenna Usage and Module Transmit Power
B2CC043AA-C module shall only be used in conjunction with the following
antenna types:
•
BelAir Networks model: BEL10012, 8.0 dBi directional diversity antenna.
•
BelAir Networks model: B1BB031AA, 11.5 dBi directional diversity
antenna.
•
MaxRad model: MFB24004, 4 dBi omni-directional antenna.
•
MaxRad model: MFB24006, 6 dBi omni-directional antenna.
•
MaxRad model: MFB24008, 8 dBi omni-directional antenna
•
MTI Wireless Edge Model MT342015 omni-directional antenna
•
MaxRad model: MFB240010, 10 dBi omni-directional antenna.
•
MaxRad model: MFB24012, 12 dBi omni-directional antenna.
In order to comply with the FCC and Industry Canada rules in the USA and
Canada, respectively, it is required to respect the maximum transmit power
limits as follows for each of the antenna types.
Antenna Models and Maximum Allowable Power Setting
Antenna
Model
Manufacturer
Antenna Type
Maximum Transmit
Power Setting(*)
BEL10012
BelAir Networks
8.0 dBi directional
diversity
+27 dBm (module
maximum power)
B1BB031AA
BelAir Networks
11.5 dBi
directional
diversity
+23 dBm (module
maximum power)
May 30 2006
Page 8 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
MFB24012
MAXRAD
12 dBi omnidirectional
+23 dBm (module
maximum power)
MFB24010
MAXRAD
10 dBi omnidirectional
+25 dBm (module
maximum power)
MFB24008
MAXRAD
8 dBi omnidirectional
+27 dBm (module
maximum power)
MTI
MTI Wireless Edge 7.5 dBi omni-
MT342015
directional
+27 dBm (module
maximum power)
MFB24006
MAXRAD
6 dBi omnidirectional
+27 dBm (module
maximum power)
MFB24004
MAXRAD
4 dBi omnidirectional
+27 dBm (module
maximum power)
* Module will transmit at reduced power levels at band edges as per factory
calibration.
Warning:
Use of this module in conjunction with any antenna not
expressly listed above will void authority to install or operate this equipment.
Warning:
Setting of module transmit power above the limits specified in
the above table will exceed FCC or Industry Canada limits and void authority to
install or operate this equipment.
Product Installation
Products which contain B2CC043AA-C shall only be installed by professional
installers trained by BelAir Networks or its authorized agents. In addition to
normal installation procedures and good installation practice, professional
installers are responsible to ensure that:
1. Only an approved antenna (see above) is connected to the module, and,
2. The antenna is mounted in such a manner and in such a location that access
to the antenna by the general population is minimized. Access to the
antenna by the general population should be limited to greater than 25.1cm
(10 inches) during normal operation.
Adherence to these rules by the professional installer is mandatory. See full
installation procedures for the particular product for details.
May 30 2006
Page 9 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
Product Labeling
The following permanent label, or one containing equivalent information, must
be affixed in a conspicuous location on the exterior of every product containing
this module:
This device contains the following:
FCC ID: RAR20000003
IC: 4674A-20000003
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including
interference that may cause undesired operation.
May 30 2006
Page 10 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
Regulatory Statements
The following regulatory notes apply to the product which contains module
B2CC043AA-C. The following sections or equivalent information shall appear
in the user-manual of the final product.
Regulatory Information and Disclaimers
Installation and use of this device must be in strict accordance with the
instructions included in the user documentation provided with the product. Any
changes or modifications to this product not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
The manufacturer is not responsible for any interference to radio or television
equipment caused by unauthorized modification of this device, or attachment of
any antennas or equipment other than those specified by the manufacturer.
The manufacturer or its authorized resellers or distributors will assume no
liability for any damage or violation of government regulations arising from
failing to comply with these guidelines.
Manufacturer’s FCC Conformity Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
May 30 2006
Page 11 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Manufacturer’s Industry Canada Conformity Statement
This device has been designed to operate with an antenna having a maximum
gain of 12 dB. Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna impedance is 50 ohms.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropic radiated power (EIRP) is
not more than that required for successful communication.
This Class B Digital apparatus meets all the requirements of the Canadian
Interference-Causing Equipment Regulations.
RF Exposure Statement
This Wireless LAN radio device has been evaluated under FCC Bulletin OET
65C and found to be compliant to the requirements set forth in CFR 47 Sections
2.1091, 2.1093, and 15.247 (b) (4) addressing RF exposure from radio
frequency devices.
This device complies with FCC RF radiation exposure limits for an
uncontrolled environment. The radiated output power of this Wireless LAN
May 30 2006
Page 12 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
device is below the FCC radio frequency exposure limits. However, this device
should still be installed and used in such a manner that the potential for human
contact during normal operation is minimized. In order to comply with RF
exposure limits established in the ANSI C95.1 standard, this equipment should
be installed and operated at a minimum distance of 25.1 cm (10 inches) between
the radiator and a human body.
May 30 2006
Page 13 of 14
PM-B2CC043AA-C
B2CC043AA-C Product Manual – 2.4 GHz WLAN Radio Module
BelAir Networks U.S. East
11921 Freedom Drive
Suite 550
Reston, VA
USA
20190
BelAir Networks U.S. West
1902 Wright Place
Suite 200
Carlsbad, CA
USA
92008
BelAir Networks Inc.
603 March Road
Kanata, Ontario
Canada
K2K 2M5
703-736-8306
760-918-5544
613-254-7070
May 30 2006
Sales
sales@belairnetworks.com
Support
support@belairnetworks.com
General Information
Info@belairnetworks.com
Page 14 of 14
PM-B2CC043AA-C

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2006:07:24 10:35:49-04:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2006:07:24 10:35:49-04:00
Format                          : application/pdf
Title                           : Microsoft Word - PM-B2CC043AA-C_Manual_IIa.doc
Creator                         : mdubois
Document ID                     : uuid:8df2dd16-88d4-47ff-83b2-48494c8807eb
Instance ID                     : uuid:e21d843d-256f-465f-8c88-d1b43a4e579f
Page Count                      : 14
Author                          : mdubois

EXIF Metadata provided by EXIF.tools