Ericsson Wi Fi 80085008 802.11n dual-band WIFI router User Manual ECON cmyk

Ericsson Wi-Fi 802.11n dual-band WIFI router ECON cmyk

UserManual.wiki >

Ericsson Wi Fi >

80085008 User Manual >

Contents

1. Users Manual
2. User Manual

Users Manual

BelAir20EO and AP 511x Series QuickInstall GuideQUICK GUIDE1/006 92-LZA 101 803 Uen D

Getting Started1 Getting Started1.1 Package ContentsExternal antennas are ordered and shipped separately.For AP 5115 to AP 5118:• Customers supply their own power cable and use the power cableconnector kit to terminate the cable.• Units can be powered either by AC power or by Power over Ethernet (PoE).21/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide1.2 AC Power (AP 5115 to AP 5118 Only)These units accept AC input power in the range of 100–240 V AC. The units donot have a power switch. They are powered on when connected to a powersource. Maximum AC power consumption is 14.5 W.Warning!The unit contains a 5-A fuse and relies on the rated fuse or circuit breaker ofthe wall outlet (15 A in North America, 10 A in Europe).Warning!Use ONLY the Ericsson power cable connector supplied with the unit. Use ofany other power cable connector can damage the unit and voids the Ericssonproduct warranty.1.3 Internet Port and PowerThe unit can be powered with IEEE 802.3af or IEEE 802.3at Power overEthernet (PoE). Use IEEE 802.3af PoE for most applications. IEEE 802.3afPoE supplies a maximum of 12.95 W to the powered device.Table 1 PoE Power Consumption TableState PoE Port OnlyPoE Port and One LANPortIdle 3.6 W 4.05 WMedium Traffic 8.4 W 8.85 WHigh Traffic 10.8 W 11.25 WMax. Traffic 11.76 W 12.21 WThe PoE switch or power injector must meet local and national regulatoryrequirements.802.3at Power Source Equipment (PSE) Specification:• 50.0 to 57 V DC, with 30 W output power from the PSE31/006 92-LZA 101 803 Uen D | 2013-12-13

Getting Started802.3at Powered Device (PD) Specification:• 42.5 to 57 V DC at the PD, with 25.5 W maximum input power to the PD802.3at Cable Specification:• 100 m maximum length• Maximum cable pair resistance of 12.5 Ohms, satisfied by using CAT5or CAT5e as specified by ANSI/TIA/EIA-568 or Class D as specified byISO/IEC 11801:1995• 600 mA maximum current per pair1.4 Functional Earth Ground and Lightning ProtectionUnits are not designed to survive a direct lightning hit. However, they areintended to withstand the voltage and current surges induced from nearbylightning activity.The level of required lightning protection depends on regional lightningconditions and location of installation. For example, an AP installed on a rooftop requires greater lightning protection than an AP installed on the side of abuilding. The following is a list of recommended installation practices to mitigatethe voltage and current surges induced from lightning activity. If there is aconflict between these recommendations and local or national electrical codes,the local or national electrical codes must be followed.• For streetlight or hydro/telecom pole mounting the AC power adaptershould be protected with a lightning surge protector. AC power routed tothe power adapter must be routed inside the pole. If power is routed on thepole exterior, the power must be routed through a metal conduit groundedat the base of the pole.• For rooftop installations, the unit must not be mounted at the highest pointon the building. If the building has installed lightning arrestors, the unit mustbe located within the umbrella protection zone—a 60 degree zone underthe lighting arrestor, but if possible, the unit should not be located closerthan 30 feet (approx. 10 m) from the lightning arrestor. Power and Ethernetcables must be routed through independent grounded metal conduits.• For lightning surge protection, the installer must connect a separate groundwire between the external chassis of the unit and a ground on the pole. Theground point on the AP accepts a 1/4” screw.• It is recommended for areas susceptible to lightning activity, such as onpoles, rooftops, or on or near any tall structures, that shielded CAT 5e orCAT 6 Ethernet cable be employed.• The external antennas ports of the unit require lightning arrestors to beemployed whenever the external antenna is located more than 3 feet41/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide(approx. 1 m) from the unit. When lightning arrestors are used, they mustbe located within 3 feet (approx. 1 m) of the unit and must be groundedto both the unit and protective earth ground. The 1/4” GND screw of theunit can be used for this application.51/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series AP2 Installing the BelAir20EO and AP 511xSeries AP2.1 Step 1—Select LocationChoose a proper place for the unit. In general, the best location is at thecenter of the intended wireless coverage area, within line of sight of all wirelessdevices. For optimum performance, consider these guidelines:• Mount the unit as high as possible above any obstructions in the coveragearea.• Avoid mounting next to or near building support columns or otherobstructions that can cause reduced signal or null zones in parts of thecoverage area.• Mount away from any signal absorbing or reflecting structures (such asthose containing metal).The unit can be mounted on any wall or on a pole.Warning!Do not install the unit in any areas where blasting (blasting caps, radiocontrolled equipment) or explosive gases can be present.Warning!To comply with FCC radio frequency (RF) exposure limits (FCC OET 65C) forthe general population, antennas must be located a minimum distance of 12inches (approx. 30 cm) or more from the body of all persons.61/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide2.2 Step 2—Mount UnitWall or Large Pole MountingLarge poles have an outer diameter greater than 3 inches (7.6 cms). If mountedon a flat surface, the unit must be mounted to a surface that is at least 1/2-inchplywood or its equivalent. Poles must have the equivalent rigidity.1. Attach the mounting plate to the wall or pole.• For walls, use up to four 1/4 inch (M6) anchoring bolts. Use the plate asa drill hole template. The outer edges of the plate must be elevated fromthe wall surface while the center channel must touch the wall surface.• For large poles, use through bolts or use the pairs of slots for stainlesssteel strapping. The center channel must touch the pole surface.2. Connect ground wire to unit.71/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series AP3. Attach four mounting screws to unit back.Note: Ground wire not shown.4. Attach unit to mounting plate:a Insert mounting screws on the back of the unit into shoulder screw holeson mounting plate. Slide unit down until screws are into the slots. Tightenscrews snug.b Screw in the remaining mounting screw at base of unit into the mountingplate hole.81/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install GuideNote: Ground wire not shown.Small Pole MountingSmall poles have an outer diameter less than 3 inches (7.6 cms).1. Connect ground wire to unit.2. Use two stainless steel straps to secure unit to pole.91/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series APNote: Ground wire not shown. Strap mounting applies to all units exceptthe AP 5115 to AP 5118.2.3 Step 3—Mount and Attach External AntennasThis step applies only to the following APs:Table 2 APs and Required AntennasAPsRequiredAntennasEricsson Descriptionand Part NumberBelAir20EO-11C,BelAir20EO-11CR2,AP 5117R, AP 5117UTwo 5 GHzExternal 11.5 dBi 5 GHz 11.5 dBi DualFeed Directional Antenna(BNCKH0091 or INE 1052162)BelAir20EO-11D,BelAir20EO-11DR2,AP 5118R, AP 5118UTwo 2.4 GHzExternal 8 dBi 2.4 GHz 8 dBi DualFeed Directional Antenna(BNCKH0007 or INE 1052159)AP 5113 One 2.4 GHzExternal 12 dBi Dual Polarization 2.4–2.5GHz Flat Panel Antenna12 dBi (KRE 105 217)Mounting Kit (KRY 901293)The external antennas must be approved by Ericsson specifically for the APs.The antennas are ordered and shipped separately.1. Attach the 5 GHz or 2.4 GHz antennas to their mounting surface.Ericsson provides several different types of 5 GHz and 2.4 GHz antennas,each with its own requirements and procedures for attaching to a mountingsurface. For details on attaching the antennas to their mounting surface,101/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guiderefer to the mounting procedures supplied with the antennas that wereordered.2. Connect external 5 GHz or 2.4 GHz antennas to connectors. See thefigure. Connect only antennas that are approved specifically for the units.Either antenna can connect to either connector. Use thread-locker andself-amalgamating tape to keep connection tight and waterproof.• Connect external 5 GHz or 2.4 GHz antennas here.• Connect only antennas that are approved specifically for the units.• Either antenna can connect to either connector.• Use thread-locker and self-amalgamating tape to keep connection tightand waterproof.Note: Ground wire and mounting hardware not shown.2.4 Step 4—Prepare Power Cable (AP 5115 to AP 5118Only)Refer to Figure 1.11 1/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series APFigure 1 Power Cable Connector Assembly1. Place compression nut (4), grommet (3), and body (2) over power cableas shown in Figure 1.2. Strip outer jacket and inner conductors as shown in Figure 1.3. Secure conductors to appropriate terminals by tightening screws on insertassembly (1). Refer to the following table.ConductorTypeNorth AmericanColorEuropean Color Terminal IDGround Green/Yellow Green/Yellow 1Power Black Brown 2Neutral White Blue 34. Attach body (2) to insert assembly (1) by rotating black knurled ring oninsert assembly in a clockwise direction.5. Secure compression nut (4) to body (2) by rotating in a clockwise direction.121/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide2.5 Step 5—Connect and Power OnBelAir20EO and All AP 511x Series: Power over EthernetThe AP gets its operating power from the PoE port when connected to a devicethat provides IEEE 802.3af or 802.3at compliant Power over Ethernet (PoE).Figure 2 Power Connection for BelAir20EO and All AP 511x Series Powerover EthernetNote: Ground wire and mounting hardware not shown.Warning!The BelAir20EO and AP 511x series AP must be connected to a power sourcethat complies to IEEE 802.3af or 802.3at.Caution!The PoE connection to the BelAir20EO and AP 511x series AP must use thesupplied Ethernet gland to ensure a waterproof connection. Failure to use theEthernet gland voids the Ericsson product warranty.AP 5115 to AP 5118 OnlyThe AP can get its operating power directly from an AC power source or fromthe Internet port when connected to a device that provides IEEE 802.3af or802.3at compliant Power over Ethernet (PoE). If the AP is connected to both aPoE source device and an AC power source, the AP automatically adjusts touse the most suitable power source.13 1/006 92-LZA 101 803 Uen D | 2013-12-13

Installing the BelAir20EO and AP 511x Series APFigure 3 Power Connections for AP 5115 to AP 5118Note: Ground wire and mounting hardware not shown.2.6 Step 6—Check IndicatorsAfter powering on, wait 2 minutes and check the indicators on the unit.If the indicators are not as shown, refer to the BelAir20EO and AP 511x SeriesTechnical Description,1/1550-LZA 101 803.2.7 Step 7—Configure UnitIn most cases, the unit configures itself automatically after powering on. Toconfigure the unit manually through its local web interface or Command LineInterface (CLI), refer to the Access Point User Guide,1/1553-LZA 101 806.141/006 92-LZA 101 803 Uen D | 2013-12-13

BelAir20EO and AP 511x Series Quick Install Guide© Ericsson AB 2013. All rights reserved. No part of thisdocument may be reproduced in any form without the writtenpermission of the copyright owner.The contents of this document are subject to revision withoutnotice due to continued progress in methodology, design andmanufacturing. Ericsson shall have no liability for any error ordamage of any kind resulting from the use of this document.1/006 92-LZA 101 803 Uen D

BelAir20EO and AP 511x Series Conformityand Regulatory StatementsSTATEMENT OF COMPLIANCE1/174 02-LZA 101 803 Uen C

ContentsContents1 About this Document 11.1 Scope 11.2 Target Group 11.3 Comments About the Documentation 12 Regulatory Information and Disclaimers 23 Manufacturer’s US Federal CommunicationCommission Conformity Statement 33.1 FCC Interference Statement 34 Manufacturer’s Industry Canada Conformity Statement 55 Manufacturer’s European Community ConformityStatement 96 Declaration of Conformity for RF Exposure 127 Product Disposal 137.1 Mise au rebut du produit 137.2 Produktentsorgung 137.3 Verwijdering van het product 137.4 Tuotteen hävittäminen 147.5 Smaltimento del prodotto 147.6 Produktbortskaffelse 147.7 Eliminação do produto 147.8 Eliminación del producto 141/174 02-LZA 101 803 Uen C | 2013-12-13

BelAir20EO and AP 511x Series Conformity and Regulatory Statements1/174 02-LZA 101 803 Uen C | 2013-12-13

About this Document1 About this DocumentThis section describes the scope and target groups for this document.1.1 ScopeThis document provides the regulatory information, disclaimers, and compliancestatements for the product.1.2 Target GroupThe information in this document is intended for all personnel who want tolearn more about the product.1.3 Comments About the DocumentationEricsson encourages you to provide feedback, comments or suggestions sothat we can improve the documentation to better meet your needs. With yourcomments provide the following:• Document title• Document number and revision• Page number or section numberPlease send your comments to your local Ericsson Support.11/174 02-LZA 101 803 Uen C | 2013-12-13

BelAir20EO and AP 511x Series Conformity and Regulatory Statements2 Regulatory Information and DisclaimersInstallation and use of this device must be in strict accordance with theinstructions included in the user documentation provided with the product.Any changes or modifications to this product not expressly approved by theparty responsible for compliance could void the user’s authority to operatethis equipment.The manufacturer is not responsible for any interference to radio or televisionequipment caused by unauthorized modification of this device, or attachmentof any antennas or equipment other than those specified by the manufacturer.The manufacturer or its authorized resellers or distributors will assume noliability for any damage arising from failure to comply with these guidelines, orfailure to comply with local, regional or national safety, electrical or buildingcodes, or government regulations.This product is manufactured in China with originating and non-originatingproduct.Ce produit est fabriqué en Chine avec des matières originaires et nonoriginaires du produit.21/174 02-LZA 101 803 Uen C | 2013-12-13

Manufacturer’s US Federal Communication Commission Conformity Statement3 Manufacturer’s US Federal CommunicationCommission Conformity StatementThis device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions (1) this device may notcause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.3.1 FCC Interference StatementThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmful interferencein a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more ofthe following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.• Consult the dealer or an experienced radio/TV technician for assistance.FCC Caution: Any changes or modifications not expressly approved by theparty responsible for compliance could void the user's authority to operatethis equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interferencethat may cause undesired operation.IMPORTANT NOTE:FCC Radiation Exposure Statement:31/174 02-LZA 101 803 Uen C | 2013-12-13

BelAir20EO and AP 511x Series Conformity and Regulatory StatementsThis device complies with FCC RF radiation exposure limits for an uncontrolledenvironment. This equipment should be installed and operated with a minimumdistance of 12 inches (30 cm) between the radiator and your body.This transmitter must not be colocated or operating in conjunction with anyother antenna or transmitter.Note: The country code selection is for non-US model only and is notavailable to all US models. Per FCC regulation, all Wi-Fi®productsmarketed in US must be fixed to US operation channels only.41/174 02-LZA 101 803 Uen C | 2013-12-13

BelAir20EO and AP 511x Series Conformity and Regulatory Statementsisotropically radiated power (e.i.r.p.) is not more than that necessary forsuccessful communication.This radio transmitter has been approved by Industry Canada to operatewith the antenna types listed above with the maximum permissible gain andrequired antenna impedance for each antenna type indicated. Antenna typesnot included in this list, having a gain greater than the maximum gain indicatedfor that type, are strictly prohibited for use with this device.Professional installation instructionPlease be advised that due to the unique function supplied by this product, thedevice is intended for use with our software and licensed third-party only. Theproduct will be distributed through controlled distribution channel and installedby trained professional and will not be sold directly to the general public throughretail store.1 Installation personnel: This product is designed for specific applicationand needs to be installed by a qualified personal who has RF and relatedrule knowledge. The general user shall not attempt to install or changethe setting.2 Installation location: The product shall be installed at a location wherethe radiating antenna can be kept 30 cm from nearby person in normaloperation condition to meet regulatory RF exposure requirement.3 External antenna: Use only the antennas which have been approved by theapplicant. The non-approved antenna(s) may produce unwanted spuriousor excessive RF transmitting power which may lead to the violation ofFCC/IC limit and is prohibited.4 Installation procedure: Refer to the BelAir20EO and AP 511x Series QuickInstall Guide,1/006 92-LZA 101 803 for details.5 Warning: Please carefully select the installation location and make surethat the final output power does not exceed the limit set force in relevantrules. The violation of the rule could lead to serious federal penalty.Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicableaux appareils radio exempts de licence. Son fonctionnement est sujet auxdeux conditions suivantes: (1) le dispositif ne doit pas produire de brouillagepréjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris unbrouillage susceptible de provoquer un fonctionnement indésirable.NOTE IMPORTANTE:Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux rayonnementsIC établies pour un environnement non contrôlé. Cet équipement doit êtreinstallé et utilisé avec un minimum de 30 cm de distance entre la source derayonnement et d’un corps humain.61/174 02-LZA 101 803 Uen C | 2013-12-13

Manufacturer’s Industry Canada Conformity StatementAvertissement:Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gainmaximal de 12 dB. Une antenne à gain plus élevé est strictement interditepar les règlements d'Industrie Canada. L'impédance d'antenne requise estde 50 ohms.Table 2 Antennes pour BelAir20EO and AP 511x seriesType Gain Marque FabricantAntenne omnidirectionnelle interne 4.4 dBi Ericsson EricssonInternal omnidirectionnelleantenna6.7 dBi Ericsson EricssonAntennedirectionnelleinterne8 dBi Ericsson EricssonAntennedirectionnelleinterne11.5 dBi Ericsson EricssonAntennedirectionnelleinterne12 dBi Ericsson EricssonAntennedirectionnelleexterne8 dBi Ericsson EricssonAntennedirectionnelleexterne11.5 dBi Ericsson EricssonConformément à la réglementation d'Industrie Canada, le présent émetteurradio peut fonctionner avec une antenne d'un type et d'un gain maximal (ouinférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduireles risques de brouillage radio-électrique à l'intention des autres utilisateurs, ilfaut choisir le type d'antenne et son gain de sorte que la puissance isotroperayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante.Le présent émetteur radio a été approuvé par Industrie Canada pourfonctionner avec les types d'antenne énumérés ci-dessus et ayant un gainadmissible maximal et l'impédance requise pour chaque type d'antenne. Lestypes d'antenne non inclus dans cette liste, ou dont le gain est supérieur augain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.Instructions d'installation professionnelle71/174 02-LZA 101 803 Uen C | 2013-12-13

BelAir20EO and AP 511x Series Conformity and Regulatory StatementsVeuillez noter que l'appareil étant dédié à une fonction unique, il doit être utiliséavec notre logiciel. Ce produit sera proposé par un réseau de distributioncontrolé et installé par des professionnels; il ne sera pas proposé au grandpublic par le réseau de la grande distribution.1 Installation: Ce produit est destiné à un usage spécifique et doit être installépar un personnel qualifié maitrisant les radiofréquences et les règles s'yrapportant. L'installation et les réglages ne doivent pas être modifiés parl'utilisateur final.2 Emplacement d'installation: En usage normal, afin de respecter lesexigences réglementaires concernant l'exposition aux radiofréquences, ceproduit doit être installé de façon à respecter une distance de 30 cm entrel'antenne émettrice et les personnes.3 Antenne externe: Utiliser uniquement les antennes approuvées par lefabricant. L'utilisation d'autres antennes peut conduire à un niveau derayonnement essentiel ou non essentiel dépassant les niveaux limitesdéfinis par FCC/IC, ce qui est interdit.4 Procédure d'installation: Consulter le manuel d’installation rapide.5 Avertissement: Choisir avec soin le lieu d'installation et s'assurer que lapuissance de sortie ne dépasse pas les limites en vigueur. La violation decette règle peut conduire à de sérieuses pénalités fédérales.81/174 02-LZA 101 803 Uen C | 2013-12-13

Manufacturer’s European Community Conformity Statement5 Manufacturer’s European CommunityConformity StatementTable 3 European Community Conformity StatementLanguage StatementEnglish This equipment is in compliance with the essentialrequirements and other relevant provisions of Directive1999/5/EC.Deutsch Dieses Gerät entspricht den grundlegenden Anforderungenund den weiteren entsprecheneden Vorgaben der Richtlinie1999/5/EU.Dansk Dette udstyr er i overensstemmelse med de væsentlige kravog andre relevante bestemmelser i Directiv 1999/5/EF.Español Este equipo cumple con los requisitos esenciales asi comocon otras disposiciones de la Directiva 1999/5/EC.Français Cet appareil est conforme aux exigences essentielles et auxautres dispositions pertinentes de la Directive 1999/5/EC.Íslenska Þessi búnaður samrýmist lögboðnum kröfum og öðrumákvæðum tilskipunar 1999/5/ESB.Italiano Questo apparato conforme ai requisiti essenziali ed agli altriprincipi sanciti dalla Direttiva 1999/5/EC.Nederlands Deze apparatuur voldoet aan de belangrijkste eisen enandere voorzieningen van richtlijn 1999/5/EC.Norsk Dette utstyret er i samsvar med de grunnleggende krav ogandre relevante bestemmelser i EU-directiv 1999/5/EC.Português Este equipamento satisfaz os requisitos essenciais e outrasprovisões da Directiva 1999/5/EC.Suomalainen Tämä laite täyttää direktiivin 1999/5/EY oleelliset vaatimuksetja on siinä asetettujen muidenkin ehtojen mukainen.Svenska Denna utrustning är i överensstämmelse med de väsentligakraven och andra relevanta bestämmelser i Direktiv1999/5/EC.The Declaration of Conformity related to this product can be found by contactingEricsson.The BelAir20EO and AP 511x series AP complies with the following EU Radiostandards:91/174 02-LZA 101 803 Uen C | 2013-12-13

BelAir20EO and AP 511x Series Conformity and Regulatory Statements•EN 300 328 V1.4.1 (2003-04) and EN300 328-2 V1.2.1 (2001-12)Electromagnetic compatibility and Radio spectrum Matters (ERM);Wideband Transmission systems; Data transmission equipment operatingin the 2,4 GHz ISM band and using spread spectrum modulationtechniques; Harmonized EN covering essential requirements under article3.2 of the R&TTE Directive.•EN 300 440-2 V1.1.1 (2001-09) Electromagnetic compatibility and Radiospectrum Matters (ERM); Short range devices; Radio equipment to be usedin the 1 GHz to 40 GHz frequency range; Part 2: Harmonized EN underarticle 3.2 of the R&TTE Directive.•EN 300 440-2 V1.1.2 (2004-07) Electromagnetic Compatibility and Radiospectrum Matters (ERM); Short range devices; Radio equipment to be usedin the 1GHz to 40 GHz frequency range; Part 2: Harmonized EN underarticle 3.2 of the R&TTE Directive.•EN 301 893 V1.4.1 (2007-07) Broadband Radio Access Networks (BRAN);5 GHz high performance RLAN; Harmonized EN covering essentialrequirements of article 3.2 of the R&TTE Directive•EN 300 328 V1.6.1 (2004-11) Electromagnetic compatibility and Radiospectrum Matters (ERM); Wideband Transmission systems; Datatransmission equipment operating in the 2,4 GHz ISM band and usingspread spectrum modulation techniques; Harmonized EN coveringessential requirements under article 3.2 of the R&TTE Directive.•UK Interface Requirement 2005 UK Radio Interface Requirement forWideband Transmission Systems operating in the 2.4 GHz ISM Band andUsing Wide Band Modulation Techniques (November 2006).•UK Interface Requirement 2006 Wireless Access Systems (WAS) includingRLANs operating in the 5150-5725 MHz band (Version 3.0) 98/34/ECNotification number: 2006/421/UK Published 14 November 2006•UK Interface Requirement 2007 Fixed Broadband Services operating inthe 5725 -5850 MHz band (Version 3.0) 98/34/EC Notification Number:2006/422/UK Published 30 May 2007The BelAir20EO and AP 511x series AP complies with the following EU EMCstandards:•EN 301 489-17 V1.2.1 (2002-08) ElectroMagnetic Compatibility and RadioSpectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) Standardfor Radio Equipment and Services; Part 17: Specific Conditions for 2.4GHz Wideband Transmission Systems and 5 GHz High PerformanceRLAN EquipmentThe BelAir20EO and AP 511x series AP complies with the following EU Safetystandards:•EN 60825-2:2000 – Safety of Optical Fibre Communication Systems10 1/174 02-LZA 101 803 Uen C | 2013-12-13

Manufacturer’s European Community Conformity Statement•EN 60950:2000 – Safety of Information Technology Equipment•IEC 60950:2005 Second Edition and/or EN 60950-1:2006The following CE mark is affixed to the BelAir20EO and AP 511x series AP:Note: This equipment is intended to be used in all EU and EFTA countries.Outdoor use may be restricted to certain frequencies and/or mayrequire a license for operation – for example in France the frequencies2454-2483.5 MHz are restricted to 10 mW effective isotropic radiatedpower (EIRP) in outdoor environments, so channels 8-13 requirereduced power. For more details, contact Ericsson.111/174 02-LZA 101 803 Uen C | 2013-12-13

BelAir20EO and AP 511x Series Conformity and Regulatory Statements6 Declaration of Conformity for RF ExposureThis Wireless LAN radio device has been evaluated under FCC Bulletin OET65C, Health Canada Safety Code 6 and EN 62311:2008, and found to becompliant to the requirements set forth in CFR 47 Sections 2.1091, 2.1093, and15.247 (b) (4) addressing RF exposure from radio frequency devices. ThisWireless LAN radio device also conforms to EU Health and Safety Directive2004/40/EC as per EN 50385.This device complies with FCC RF radiation exposure limits for an uncontrolledenvironment. The radiated output power of this Wireless LAN device is belowthe FCC radio frequency exposure limits. However, this device should stillbe installed and used in such a manner that the potential for human contactduring normal operation is minimized.Warning!In order to comply with RF exposure limits established in the ANSI C95.1standard, this equipment should be installed and operated at a minimumdistance of 12 inches (30 cm) between the radiator and a human body.This transmitter must not be colocated or operating in conjunction with anyother antenna or transmitter.The availability of some specific channels and/or operational frequency bandsare country dependent and are firmware programmed at the factory to matchthe intended destination. The firmware setting is not accessible by the end user.12 1/174 02-LZA 101 803 Uen C | 2013-12-13

Product Disposal7 Product DisposalEricsson adheres to directive 2002/96/EC of the European Parliament andthe council of 27 January 2003 on Waste Electrical and Electronic Equipment(WEEE).To dispose of equipment, including batteries, contact Ericsson customer serviceto get a Return Material Authorization (RMA) number and shipping instructions.7.1 Mise au rebut du produitEricsson se conforme à la directive 2002/96/EC du Parlement européen et duConseil de l’Europe du 27 janvier 2003 relative à la destruction des déchetsd’équipements électriques et électroniques (DEEE).Si vous souhaitez vous débarrasser de l’équipement, y compris des piles,veuillez communiquer avec le service à la clientèle de Ericsson, afin d’obtenirun numéro d’autorisation de retour du matériel et des instructions sur lesmodalités d’expédition.7.2 ProduktentsorgungEricsson erfüllt die Anforderungen der Richtlinie 2002/96/EG desEuropäischen Parlaments und des Rates vom 27. Januar über Elektro- undElektronik-Altgeräte (Waste Electrical and Electronic Equipment = WEEE).Für die Entsorgung von Geräten, einschließlich Batterien, wenden Siesich bitte an den Kundendienst von Ericsson, um eine RMA-Nummer(Rücksendenummer) und die Versandanweisungen zu erhalten.7.3 Verwijdering van het productEricsson volgt Richtlijn 2002/96/EG van het Europese Parlement en de Raadvan 27 januari 2003 betreffende afgedankte elektrische en elektronischeapparatuur (AEEA).Voor het verwijderen van apparatuur, met inbegrip van batterijen, neemt ucontact op met Ericsson klantenservice voor een retournummer (RMA) enverzendinstructies.131/174 02-LZA 101 803 Uen C | 2013-12-13

BelAir20EO and AP 511x Series Conformity and Regulatory Statements7.4 Tuotteen hävittäminenEricsson noudattaa sähkö- ja elektroniikkalaiteromusta 27 päivänä tammikuuta2003 annettua Euroopan parlamentin ja neuvoston direktiiviä 2002/96/EY.Palauttaaksesi välineet, mukaan luettuina akut, ota yhteys Ericsson–asiakaspalveluun, niin saat RMA (Return Material Authorization) –numeronja lähetysohjeet.7.5 Smaltimento del prodottoEricsson aderisce alla direttiva 2002/96/CE del parlamento Europeo e delConsiglio d’Europa del 27 gennaio 2003, sullo smaltimento degli apparecchielettrici ed elettronici (WEEE).Per lo smaltimento di tali apparecchi, comprese le batterie, contattarel’assistenza clienti di Ericsson per ottenere un numero di autorizzazione allarestituzione del materiale da smaltire (Return Material Authorization - RMA) e leistruzioni per la spedizione.7.6 ProduktbortskaffelseEricsson overholder direktivet 2002/96/EC fra Europa-Parlamentet og -Rådetdateret den 27. januar 2003 om Waste Electrical and Electronic Equipment(WEEE) (Affald af elektrisk og elektronisk udstyr).For at bortskaffe udstyr, samt batterier, kontakt kundeservicen hosEricsson for at få et Return Material Authorization (RMA)-nummer(returneringstilladelsesnummer) og forsendelsesinstruktioner.7.7 Eliminação do produtoA Ericsson cumpre a Directiva 2002/96/CE do Parlamento Europeu e doConselho, de 27 de Janeiro de 2003, relativa aos Resíduos de EquipamentosEléctricos e Electrónicos (REEE).Para proceder à eliminação do equipamento, incluindo as baterias, é favorcontactar a assistência ao cliente da Ericsson para obter um número deAutorização de Devolução do Material (RMA – Return Material Authorization) eas instruções relativas ao envio.7.8 Eliminación del productoEricsson cumple con la directiva 2002/96/EC del Parlamento Europeo y delConsejo de 27 de enero de 2003 sobre los residuos de aparatos eléctricos yelectrónicos (RAEE).14 1/174 02-LZA 101 803 Uen C | 2013-12-13

Product DisposalPara la eliminación de equipo, incluyendo las pilas, contacte con el servicio deatención al cliente de Ericsson y obtenga el número de una Autorización deDevolución de Material (RMA) y las instrucciones para la expedición.151/174 02-LZA 101 803 Uen C | 2013-12-13