Esorun Technology PAD Wireless Charger User Manual

Shenzhen Esorun Technology Co.,LTD Wireless Charger

user manual

User Manualsili padAntiskid Support With Wireless ChargerShenzhen Esorun Technology Co.,LTDInformation to UserCAUTIONPlease read this manual carefully before using this product for your safety and best productperformance. Failure to follow these instructions could result in serious injury, damage to thisproduct, or damage to other products.Do not install this product in your vehicle if its location or use would obstruct the driver's clear viewof the road or the operation of any vehicle airbag. It is also the driver's responsibility to know andcomply with the laws, rules, and regulations of the driving location.Do not place this product in direct sunlight for an extended amount of time, or where it could be exposedto extreme temperatures. Store out of direct sunlight when not in use.Do not allow this product to come into contact with liquids. Electrical shock could result. Also, damageto the product, smoke, and overheating could result from contact with liquids.If you notice smoke or odor from this product, disconnect USB cable immediately. Using the product in thiscondition may result in permanent damage to the system.Do not disassemble or modify this product as there are electronic components inside that may cause anelectric shock.Keep this manual handy as a reference for safety information.ACCESSORIESWireless charging pad x 1●FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITYProduct Name: Antiskid Support With Wireless ChargerModel Number: sili padResponsible Party Name: Shenzhen Esorun Technology Co.,LTDAddress: 10F, Mingzhuo Building, Mingzhuoxing Industrial Park,Guangming Street, Guangming District, Shenzhen, China●This device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.●NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:‒Reorient or relocate the receiving antenna.‒ Increase the separation between the equipment and receiver.‒ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‒ Consult the dealer or an experienced radio/TV technician for help.●Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
USB Type A to USB Type C data cable 1m(39.4in.) x 1User Manual x 1*A USB Type-A power adapter that outputs at least 5V⎓2A is required; not included.Compatible with Qi Certified mobile devices only. Do not use with any otherdevice.SPECIFICATIONPower: 10WWeight: 180g (6.4ounces)Input Voltage: 5 V⎓2A; 9 V⎓1.67AOutput Voltage: 5 V⎓1A; 9 V⎓1.12ADimensions: 185 x 100 x 26mm (7.3in. x 3.9in. x 1.0in.)Charging Efficiency: ≥ 70%Transmission Distance: ≤ 6mm (0.2in.)Operating Temperature: -20 ℃ to + 60℃ (-4℉ to + 140℉)Note: Specifications and design are subject to possible modification without notice.①USB Type-C input port②Charging areaHOW TO USESetting up your wireless charging pad1. Connect your wireless charging pad to power adapter via included USB Type A to USB Type C data cable.<!> Connected power adapter must output at least 5V/2A. Using an adaptor with a lower outputmay result in malfunction or overheating.<!> Never place or use this product, including the data cable, in a manner that may: * Injure the driver or passengers if the vehicle stopped suddenly * Interfere with the driver's safe operation of the vehicle, such as on the floor infront of the driver's seat, or close to the steering wheel or gear stick * Obstruct the driver's clear view of the road, or * Impair or interfere with the performance of any of the vehicle's operating systems orsafety features, including airbags and hazard lamp buttons. Please refer to yourvehicle's owner's manual for deployment area of front and side airbags.<!> Make sure the data cable will not interfere with or become caught in or wound around any ofthe vehicle's moving parts, especially the steering wheel, gear stick, handbrake, sliding seattracks, doors, or vehicle controls.2. Your wireless charging pad is ready for your mobile device.Charging mobile device from wireless charging padPut your Qi Certified mobile device on the center of the wireless charging pad.<!> Quick Charge™ 2.0, Quick Charge™ 3.0 or Quick Charge™ 4.0 power adapter required for fastcharge mode.<!> Charging speed may vary depending on device specifications, input voltage, and environment.<!> Phone cases or metal plates for magnetic attachment might interfere with wireless charging.<!> Do not place magnetic stripe cards such as credit cards, driver's license, or parkinggarage ticket between mobile device and this product. Doing so may demagnetize the card.PRODUCT CARE・Do not bend or fold the product as this will damage the internal circuit board and chips.・Keep your wireless charging pad dry.・Keep pad away from all types of liquids or moisture, which could corrode electronic circuits.・Do not clean the wireless charging pad with soaps, detergents or chemicals USB Type-A power adapter(not included)USB Type A to USB Type C data cableFrench:Bloc d'alimentation USB Type A(Non-inclus)French:Câble USB de 1 mêtre (Type A vers Type C)
If your wireless charging pad is not working properly・Make sure your mobile device is Qi Certified.・Make sure your adapter is at least 5V/2A.・Clean any dirt or debris from the pad using a soft, dry cloth.・The wireless charging pad may stop charging when overheated. Remove your mobile device and try chargingagain when the charging pad has cooled down.REMARKS1. Use only the included USB data cable. Wireless charging pad may not function with another cable.2. This wireless charging pad and your mobile device may become warm even under normal operatingconditions, especially when charging and using the device at the same time such as streaming music ornavigation. Stop using the charging pad if it or your mobile device becomes overheated.WARRANTYThis product is covered in the United States and Canada by Pioneer's 90 day Limited Warranty. Please seehttp://pioneerelectronics.com/wcwarranty for complete terms and conditions.CUSTOMER SUPPORTIf you have any questions, please contact Pioneer Customer Service toll free at 1-800-421-1404, Mondaythrough Friday, 7:30 AM - 11:30 AM and 12:30 PM - 4:00 PM (Pacific Time), excluding holidays, or onlinethrough parts.pioneerelectronics.com/contact.Qualcomm Quick Charge is a product of Qualcomm Technologies, Inc. 

Navigation menu