Euro Communication EquipementS BTCRY6 BTCRY6 User Manual OPERATING MANUAL

Euro Communication Equipement SAS BTCRY6 OPERATING MANUAL

user manual

BTCRY6Bluetooth Handsfree KitManual
A. Product Overview1. On/Off Button2. Reject Button3. MFB Button4. Volume Down5. Volume Up6. Microphone7. Charger Port8. Bluetooth Indicator / Charge Indicator9. SpeakerB. Charging1. Connect the charger’s plug to the Charger Port (7) of the SUPERTOOTH CRYSTAL. Connect the charger to an external power source.Charge Indicator (8) Status:Steady Red: Battery LowSteady Orange: Charging Steady Green: Battery Full2. When fully charged, disconnect the charger.C. Power On/OffPower On: Press the On/Off (1) button for 1 second, the Bluetooth Indicator (8) turns blinking blue. A beep will be heard.Power Off: Press and hold the On/Off (1) button for 3 seconds, until the Bluetooth Indicator (8) turns red. A beep will be heard.D. Pairing to your Bluetooth Mobile PhonePair the SUPERTOOTH CRYSTAL to your Bluetooth mobile phone to create the link or audio connection between the two. The pairing process is required only once for each phone.Pairing Procedure : 1. From OFF, press and hold the On/Off (1) button until the Bluetooth Indicator (8) turns blinking red/blue. The handsfree kit is now in pairing mode.
2. While the handsfree kit is in pairing mode, access the Bluetooth menu of your phone. Turn on the Bluetooth function then execute a Bluetooth search. (See your phone’s manual.)3. When the phone displays the list of Bluetooth devices, select BTCRY6.4. When the phone asks for the password/pin code, enter 0000 and press Ok.5. The handsfree kit is now ready to use.E. Basic OperationsIMPORTANT : The handsfree kit needs to be ‘paired’ to your Bluetooth mobile phone, before you can use the following functions. See “Pairing to your Bluetooth Mobile Phone in Section D”.Make a Call ( Normal Dial ): Dial the number on your phone. Audio will automatically be heard through the handsfree kit. During an ongoing call, the Bluetooth Indicator (8) will turn steady blue.Note: With some phones, audio is always on the phone during an outgoing call. You will need to press the MFB (3) button for 1 second to transfer the audio to your handsfree kit.Answer a Call : To answer a call, simply press the MFB (3) button for 1 second, the Bluetooth Indicator (8) will turn steady blue.End a Call : Press the MFB (3) button for 1 second to end the call.Voice Dial : Important : Before using this feature, make sure that the voice dialing function of your phone is activated and at least one voice tag is recorded on your phone. (Kindly refer to the procedure in your phone’s manual.) Note: Voice dialing entries must be stored in the phone’s memory, not on the SIM card!1. Press the MFB (3) button for 1 second.2. A voice dial beep will be heard on the handsfree kit prompting you to say the voice tag of the contact to call and the Bluetooth Indicator (8) will turn steady blue.
3. Say the voice tag exactly as how you recorded it.4. The voice tag will be played back to you and then the phone will dial the number automatically.Redial ( For Handsfree Profile Phones only ) : Press the MFB (3) button for 3 seconds. The last dialed number will be redialed.Reject a Call ( For Handsfree Profile Phones only ) : During the ring tone, short press Reject (2) button.Volume Setting : Increase or decrease the volume by pressing the Volume Up (5) or Volume Down (4) button. Press repeatedly until the desired level is reached. A beep will be heard as lowest and highest levels are reached.Audio Transfer ( Phone to HF / HF to Phone ): During an ongoing call, you can transfer the audio.Press the MFB (3) for 3 seconds and the audio will be transferred.Note: For some phones, you may need to accept a connection prompt on the phone before automatic transfer takes place.To Reconnect Phone to Kit : In case of intentional disconnection (using the phone menu), short press MFB (3) button to reconnect. Beep will be heard then phone reconnect to kit.F Special Features3- Way Calling : You can talk with two parties at the same time with a three-way conversation on your SUPERTOOTH CRYSTAL. Note: This 3-way calling is Network Service dependent.To end the current call and accept the second incoming callShort press MFB (3) button will end the current call and accept the second call. The audio for the second call will be heard through the handsfree kit.Short press MFB (3) button will end the call.
FCC/IC statements :Federal Communications Commission (FCC) StatementIndustry Canada (IC) Statement15.21You are cautioned that changes or modications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC/IC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit di-erent from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.Operation is subject to the following two conditions :1)This device may not cause interference and2)This device must accept any interference, including interference that may cause undesired operation of the device.FCC/IC RF Radiation Exposure Statement :This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Euro-CB is under license. Other trademarks and trade names are those of their respective owners.EnglishEnglishHerebyHereby, , EUROEURO COMMUNICATIONCOMMUNICATION EQUIPEMENTSEQUIPEMENTS, , representedrepresented byby XavierXavier MARCHANTMARCHANT, , CEOCEO, , declaresdeclares thatthat thethe SUPERTOOTHSUPERTOOTH CRYSTAL, CRYSTAL, MODELMODEL BTCRY6, BTCRY6, isis inin compliancecompliance withwith thethe essentialessential requirementsrequirements andand otherother relevantrelevant provisionsprovisions ofof DirectiveDirective 1999/5/ 1999/5/ECEC ofof thethe EuropeanEuropean ParliamentParliament andand ofof thethe CouncilCouncil ofof 9 9 MarchMarch 1999 1999 onon radioradio equipmentequipment andand telecommunicationstelecommunications terminalterminal equipmentequipment andand thethe mutualmutual recognitionrecognition ofof theirtheir conformityconformity..ForFor thethe wholewhole declarationdeclaration pleaseplease visitvisit ::httphttp ://:// wwwwww .. SuperToothSuperTooth .. frfr // downloaddownload EuroEuro CommunicationCommunication EquipementsEquipements SasSasRouteRoute dede FoixFoix DD11711711 500 11 500 NEBIASNEBIASFRANCEFRANCE

Navigation menu