EuroCB BTF7 Interphone Shape User Manual Revised

Download:
Mirror Download [FCC.gov]
Document ID	3768885
Application ID	lwT7bh4wEGsE/ySqqXvFPA==
Document Description	Users Manual Revised
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.12kB (138996 bits)
Date Submitted	2018-03-05 00:00:00
Date Available	2018-03-06 00:00:00
Creation Date	2018-03-01 09:10:23
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-03-01 09:10:23
Document Title	Users Manual Revised
Document Creator	Adobe InDesign CC 13.0 (Windows)

WARNING ON THE BATTERY OF THE PRODUCT
Fully charge the battery before using the product for the first time.
Do not store the Product without charging it. Failure to do so may cause irreversible damage to the battery capacity. Charge the battery every TWO months.
WARNING ON THE WATER RESISTANCE OF THE PRODUCT
The external unit (control unit), connected to the audio kit, can be immersed in a meter of
fresh water for a maximum of 30 (thirty) minutes.
Despite this, the device is not immune to greater stress, such as prolonged immersions or
high pressure water jets.
Using the product during intense meteorological phenomena, at high speeds, may be
equivalent to subjecting the product to a high pressure jet.
FOLLOW ALL SUGGESTIONS CAREFULLY TO AVOID DAMAGING THE DEVICE:
Do not immerse the product in fresh water which is more than a metre deep for more than
30 minutes.
Do not store the product when still wet: dry it with a clean, soft cloth.
Do not expose the product to salt water or ionised water, drinks or other liquids.
If the device is exposed to liquids other than fresh water, wash the device with cold fresh
water and dry it carefully with a clean, soft cloth.
Do not expose the product to high pressure water jets.
CHAPTER 2 – INSTALLATION INSTRUCTIONS
CHAPTER 1 – COMPOSITION OF THE KIT
Vol +
MFB (On-Off)
Vol -
Choose the bracket to use, to be attached on the left side of the helmet:
Bluetooth unit
If possible, remove the two
cushions or padding
Position the strips of Velcro
for the speakers
Locate the area in correspondence
with the ear
Sticker
Bracket
Place the speakers
Re-install the cushions
Choose the microphone to use:
Install the control unit
(!) Warnings on installation:
1. The centre of the speakers must be placed
in correspondence with the ears, as close as
possible.
QUICK GUIDE
CHECK FOR SOFTWARE UPDATES ON WEBSITE
www.interphone.com
Filp-up/jet helmet
Full face helmet
2. The marking “MIC” on the microphone
must be directed towards the mouth.
MIC
QUICKGUIDESHAPEEN
CHAPTER 3 - BATTERY CHARGE
Insert the micro USB charging cable in the special intercom connector, as shown in the
picture. Connect the cable to a standard USB charger.
LED indications:
- orange LED: charging.
- green LED: fully charged
Redial last number
Double press MFB.
CHAPTER 6 – MUSIC
Enable/disable playback from the phone
Press MFB until the second beep.
Next track
On music playback, press Volume + until the first beep.
Previous track
On music playback, press Volume - until the first beep.
Share the music with another intercom
On music playback, press Volume + until the second beep.
To stop sharing, press Volume - until the second beep.
CHAPTER 4 - BASIC CONFIGURATION
Turn the device on
Press MFB until the blue LED comes on.
Turn the device off
Press MFB until the red LED lights up and the device turns off.
Activate / Deactivate automatic volume control
1. With the device off, press MFB until the second beep. Led will flash red/blue.
2. To activate, press Volume + until the first beep. Led will flash blue for 4 seconds.
3. To deactivate, press Volume - until the first beep. Led will flash red for 4 seconds.
Pairing with a NON-Interphone device (for the first time only)
1. In the NON-Interphone unit, start the telephone search/pairing mode; refer to the
user manual of the intercom to be paired.
2. With Interphone SHAPE off, press MFB until led will flash red/blue.
3. Short press MFB button on Interphone SHAPE, units will pair and connect.
Activate / Deactivate phone calls voice answer
1. With the device off, press MFB until the second beep. Led will flash red/blue.
2. To activate, press Volume + until the second beep. Led will flash blue for 4 seconds.
3. To deactivate, press Volume - until the second beep. Led will flash red for 4 seconds.
Two way intercom talk
On one unit only, press MFB until the first beep.
To stop communication, on one unit only, press MFB until the first beep.
Factory Reset
With the device off, press together MFB and Volume + and Volume – until the device
switches on. All settings and pairings will be erased.
CHAPTER 5 - TELEPHONE / GPS
Pairing
1. With the device off, press MFB until the second beep. Led will flash red/blue.
2. Start searching for new devices on the mobile phone / GPS
3. Select the intercom on the phone / GPS “interphone shape”.
4. Once the pairing has been confirmed, the LED will flash BLUE twice, every three
seconds.
www.cellularline.com
S1217
Answering a call
Just say loudly “HELLO” or short press MFB.
Via Lambrakis 1/A, 42122 Reggio Emilia, Italy
CHAPTER 7 – INTERCOM
Pairing with another Interphone device (for the first time only)
1. With both the intercom devices off, on each unit press power-on button until led will
flash red/blue.
2. Short press MFB button on one Interphone SHAPE, units will pair and connect.
Voice dial
Short press MFB.
SPECIFICHE TECNICHE
Bluetooth® compliance: 		
Supported Bluetooth profiles:
Frequency: 		
Power: 		
Operating temperature: 		
Charging temperature: 		
Dimensions mm: 		
Weight: 		
Capacity: 		
Talk time: 		
Stand-by time: 		
Charging time: 		
Battery type: 		
Bluetooth v. 3.0 - Class II
HFP A2DP AVRCP
2.402 – 2.480GHz
7dBm EIRP
0 – 45°C
10 - 40°C
36x78x18
61 g
Up to 10 meters
12 h
700 h
3h
Lithium-ion rechargeable
WARNING: To prevent possible hearing damage, do not listen at high volume levels for long periods.
Federal Communications Commission (FCC) Statement
Industry Canada (IC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to
operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC/IC rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures :
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules and Industry Canada licence-exempt RSS standard(s)
Operation is subject to the following two conditions :
1)This device may not cause interference and
2)This device must accept any interference, including interference that may cause undesired operation of the device.
FCC / IC RF Radiation Exposure Statement:
This equipment complies with FCC / IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 10mm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
EN - Hereby, Cellular Italia S.p.A declares that the radio equipment type
BTF7 (Interphone Shape) is in compliance with
Directive 2014/53/EU and Directive ROHS (2011/65/EU). The user is
prohibited from making any type of change or variation to the device.
Variations or changes not expressly approved by Cellular Italia S.p.A
will cancel the user’s authorisation to use the device.
Only update with software provided by Cellular Italia S.p.A.
Bluetooth® is a trademark owned by Bluetooth SIG, Inc.
The full text of the EU declaration of conformity is available at the
following internet address: http://www.cellularline.com/it_it/dichiarazione-conformita/
EN - INSTRUCTIONS FOR THE DISPOSAL OF APPLIANCES FOR DOMESTIC
USERS
(Applicable in countries in the European Union and those with separate
waste collection systems)
This mark on the product or documentation indicates that this product must
not be disposed of with other household waste at the end of
its life. To avoid any damage to health or the environment due to improper
disposal of waste, the user must separate this product from
other types of waste and recycle it in a responsible manner to promote the
sustainable re-use of the material resources.
Domestic users should contact the dealer where they purchased the product
or the local government office for all the information
regarding separate waste collection and recycling for this type of product.
Corporate users should contact the supplier and verify the
terms and conditions in the purchase contract. This product must not be
mixed with other commercial waste.
This product has a battery than cannot be replaced by the user. Do not
attempt to open the device to remove the battery as this could
cause malfunctions and seriously damage the product. When disposing of
the product, please contact the local waste disposal authority
to remove the battery. The battery inside the device was designed to be able
to be used during the entire life cycle of the product

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c143 79.161210, 2017/08/11-10:28:36
Create Date                     : 2018:03:01 09:10:23+08:00
Metadata Date                   : 2018:03:01 09:10:23+08:00
Modify Date                     : 2018:03:01 09:10:23+08:00
Creator Tool                    : Adobe InDesign CC 13.0 (Windows)
Instance ID                     : uuid:10a9a447-59f7-4450-a62a-a841c3f76158
Original Document ID            : xmp.did:81c7624c-481a-4904-86b2-48951d7879c9
Document ID                     : xmp.id:89c91e4b-5347-054a-863b-d61b6400e43e
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:8b13a1cb-021b-194d-8b3e-392baabb50a6
Derived From Document ID        : xmp.did:dd89af9a-3404-b445-888c-7558c60bd1bc
Derived From Original Document ID: xmp.did:81c7624c-481a-4904-86b2-48951d7879c9
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.0 (Windows)
History Changed                 : /
History When                    : 2018:03:01 09:10:23+08:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CC 13.0 (Windows)

EXIF Metadata provided by EXIF.tools