EverFocus Electronics 198NV2 802.11abgn Mini PCI module User Manual WMIA 198N Manual English V1 0

Download:
Mirror Download [FCC.gov]
Document ID	2083799
Application ID	wxvb03AWx8m/xkcogdgb/A==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	82.54kB (1031713 bits)
Date Submitted	2013-09-27 00:00:00
Date Available	2014-03-25 00:00:00
Creation Date	2013-09-09 13:38:43
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2013-09-25 16:05:37
Document Title	Microsoft Word - WMIA-198N Manual_English_V1.0
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Owner

WMIA-198N
Specifications
Standard
IEEE 802.11abgn
Chipset solution
Atheros AR9220
Radio stream [Note1]
2T2R
Antenna Type / con.
2 U.FL connectors
Bus Interface
32-bit mini-PCI Type lll A
Form Factor
Mini PCI
802.11b: 1, 2, 5.5, 11Mbps
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
Data Rate
802.11a: 6, 9, 12, 18, 24, 36, 48, 54Mbps
802.11n: MCS 0 to 15 for HT20MHz
MCS 0 to 15 for HT40MHz
Spreading /Modulation
Techniques
802.11b: DSSS (DBPSK, DQPSK, CCK)
802.11g: OFDM (BPSK, QPSK, 16-QAM, 64-QAM)
802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM)
802.11n: OFDM (BPSK, QPSK, 16-QAM, 64-QAM)
Frequency Range[Note2]
2.4GHz: 11b/g/n: 2.400GHz ~ 2.4835GHz
5GHz: 11a/n: 5.150GHz ~ 5.825GHz
Transmit Output Power
(Tolerance: +/-2dBm)
802.11b: 18dBm@11Mbps
802.11g: 17dBm@54Mbps
802.11a: 16dBm@54Mbps
802.11gn HT20: 17dBm@MCS7
802.11gn HT40: 17dBm@MCS7
802.11an HT20: 12dBm@MCS7
802.11an HT40: 9dBm@MCS7
Receiver Sensitivity
(Tolerance: +/-2dBm)
802.11b: -90dBm @11Mbps
802.11g: -78dBm@54Mbps
802.11a: -76dBm@54Mbps
802.11gn HT20: -74dBm@MCS7
802.11gn HT40: -73dBm@MCS7
802.11an HT20: -74dBm@MCS7
802.11an HT40: -69dBm@MCS7
Operating Voltage
3.3 V ±10 % I/O supply voltage
Power Consumption
TX Mode: 800mA(Max)
RX Mode: 300mA(Max),
Temperature Range
0° ~ +60°C (Operating), -20°~+80°C (Storing) [Note3]
Humidity (non-condensing) 15~90%(Operating), 5~95 % (Storing) [Note3]
Security
WEP / WPA / WPA2
OS supported
Windows XP/Vista/Win7, Linux
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains FCC ID:
TNU-198NV2”. The grantee's FCC ID can be used only when all FCC compliance
requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
Quick Installiaton Guide
Version 1.0
Contents
1. Package Contents........................................................................................................... 7
2. Quick installation Guide .................................................................................................. 8
3. Driver Installation ............................................................................................................ 8
4. Connect to Wireless Access Point ................................................................................ 12
Copyright statement
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, whether electronic, mechanical, photocopying, recording, or
otherwise without the prior writing of the publisher.
April 2012
1. Package Contents
Before you starting to use this Mini PCI Module, please check if there’s anything missing in
the package, and contact your dealer of purchase to claim for missing items:
Package Contents
Please make sure you have the following in the box:
♦
Atheros Mini PCI Module
♦
Driver / QIG CDROM
Note: if anything is missing, please contact your vendor
2. Quick installation Guide
Please follow the following instructions to use Atheros Wireless Configuration (AWiC) to
connect to wireless access point.
3. Driver Installation
1. Setup your Atheros Mini PCI Module into an empty Mini PCI slot of your computer.
2. Insert the Driver CD, browse to the driver folder then double click the “setup.exe” file to
start the driver installation.
3. You will see “Atheros Client Installation Program – InstallShield Wizard” appears.
Please choose the languague which you need, and then click “Next” to begin the
installation.
4. Click “Next” and then follow the instructions on the screen to continue the installation.
10
5. When you see this message, please click “Finish” to complete the driver installation
process, and please reboot your computer.
11
4. Connect to Wireless Access Point
1. After installation is complete, an “Atheros Wireless Network Connection Manager
Utility” shortcut will show on the desktop. You can double click it to start the “Atheros
Wireless Network Connection Manager”.
2. When “Atheros Wireless Network Connection Manager” appears, please double click
the item which you want to start “AWiC”.
12
3. You will see “Atheros Wireless Configuration” (AWiC) shows on your desktop.
13
4. You could follow the steps to connect to the AP which you want to connect.
a. Click the “Browse nearby wireless networks” icon to see the site survey table.
14
b. You could choose one of the APs in the list to connect; on this sample, we will
connect to the AP called “1591” with WPA2-PSK/AES Security/Encryption type, we
just need to double click on the AP named “1591”, and the “create new profile”
window will appear automatically.
c. Click the “Advanced security setting” icon to modify the Security/Encryption type
manually in the “Wireless Network Properties” window, and then enter the “Network
security key”.
15
d. Click "OK" to save the profile, and then click “Connect” to connect to the AP you
choose.
You will see your profile shows in the AWiC, and there showns the module has
“connected” to AP.
Be careful, if the “Network security key” was entered incorrect, you won’t be able to
exchange any data frames, even though the AP can be connected.
16
5. At last, if you want to know more using method of AWiC, you could refer to the help file
by click the question mark
at the top right corner of AWiC to open it.
Atheros Wireless Configuration Help.
17

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2013:09:09 13:38:43+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2013:09:25 16:05:37+08:00
Metadata Date                   : 2013:09:25 16:05:37+08:00
Format                          : application/pdf
Title                           : Microsoft Word - WMIA-198N Manual_English_V1.0
Creator                         : Owner
Document ID                     : uuid:9285f62a-1af1-4ddf-a71b-b5e99bfa7961
Instance ID                     : uuid:d0bb80f1-e06c-4e84-8fb4-c3c73053ee78
Page Count                      : 18
Author                          : Owner

EXIF Metadata provided by EXIF.tools