EverFocus Electronics EVS200AW-W 2CH Video Encoder User Manual EVS200A manual draft

Download:
Mirror Download [FCC.gov]
Document ID	1176020
Application ID	FRy2ENHef7Ahl/GdYSZUHQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	268.29kB (3353651 bits)
Date Submitted	2009-09-28 00:00:00
Date Available	2009-09-28 00:00:00
Creation Date	2009-08-13 10:02:04
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2009-09-28 09:35:36
Document Title	Microsoft Word - EVS200A_manual_draft.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	hazel

EVS200A/EVS200AW
User’s Manual
Copyright © EverFocus Electronics Corp,
Release: Sept. 2009 Rev.0
EVS200A/EVS200AW
Product Name: EVS200A/EVS200AW EverFocus 2CH Video Encoder
Model Number(s): EVS200A/EVS200AW
FCC Notice "Declaration of Conformity Information"
RF Declaration should be added. Please check Safety team.
This
found
to to
comply
with
the the
limits
for afor
Class
A digital
This equipment
equipmenthas
hasbeen
beentested
testedand
and
found
comply
with
limits
a Class
device,
pursuant
part 15 of
Rules.
TheseRules.
limitsThese
are designed
to provide
A digital
device,topursuant
tothe
partFCC
15 of
the FCC
limits are
designed
reasonable protection against harmful interference when the equipment is operated in a
to provide reasonable
protection
againstgenerates,
harmful interference
a residential
commercial
environment.
This equipment
uses, and caninradiate
radio frequency
Installation.
This
equipment
generates,
uses
and
can
radiate
radio
frequency
energy
energy and, if not installed and used in accordance with the instruction manual, may
cause
harmful
interference
to
radio
communications.
Operation
of
this
equipment
in
residential
and, if not installed and used in accordance with the instructions, may cause harmful
area
is likely to
to cause
harmful interference
in whichthere
case the
user
will be required
to
interference
radio communications.
However,
is no
guarantee
that
correct the interference at his own expense.
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this equipment, not expressly approved
by EverFocus or parties authorized by EverFocus could void the user's authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with
any other antenna or transmitter.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
EverFocus Electronics Corp.
12F, No. 79, Sec. 1, Shin-Tai Wu Rd., His-Chi,
Taipei Hsien, Taiwan, R.O.C.
EVS200A/EVS200AW
EVS200A/EVS200AW complies with CE and FCC.
About this document
All the safety and operating instructions should be read and followed before the
unit is operated. This manual should be retained for future reference. The
information in this manual was current when published. The manufacturer reserves
the right to revise and improve its products. All specifications are therefore subject
to change without notice.
Safety Notice
-These limits are designed to provide reasonable protection. This equipment
generates, uses and can radiated radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures: -Reorient or relocate the receiving antenna.
-Increase these separations between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
To reduce risk of fire or electric shock, do not expose this appliance to rain or
moisture.
Do not attempt to disassemble the appliance.
To prevent electric shock, do
not remove screws or covers. There are no user-serviceable parts inside.
Contact qualified service personnel for maintenance. Handle the appliance with
care. Do not strike or shake, as this may damage the appliance.
Do not use strong or abrasive detergents when cleaning the appliance body.
Use a dry cloth to clean the appliance when it is dirty.
When the dirt is hard to
EVS200A/EVS200AW
remove, use a mild detergent and wipe gently.
Do not operate the appliance beyond its specified temperature, humidity or
power source ratings. Do not use the appliance in an extreme environment where
high temperature or high humidity exists. Use the appliance at temperature within
0℃ ~ +40℃ / 32℉ ~ 104℉ and a humidity below 90%. The input power source for
this appliance is 12 VDC & PoE.
Use only the recommended power supplies. Power supplies must comply
with the requirement of the latest version of IEC60950-1. Substitutions may
damage the unit or cause a fire or shock hazard.
Electrostatic-sensitive device. Use proper CMOS/MOSFET handing
precautions to avoid electrostatic discharge.
Installation should be performed by qualified service personnel only in
accordance with the National Electrical Code or applicable local codes.
Terms and Trademark
Ethernet, Internet Explorer, Linux, Microsoft, Windows, WWW are registered
trademarks of the respective holders. Other product names appearing in this User's
Guide may be trademarks or registered trademarks of their respective holders.
Java™ and all Java-related logos and trademarks are trademarks or registered
trademarks of Sun Microsystems, Inc. in the United States and other countries.
Support
If the unit ever needs repair service, the customer should contact the nearest
EverFocus Electronics Corp. Service Center for return authorization and shipping
instruction.
About AC Adaptor
Specifications for AC adaptor
Power Supply: 12VDC, 1 A
Power Output: 12VDC, 1 A
Operating Temperature: 0℃ ~ 40℃ / 32℉ ~ 104℉
External Dimensions: 56 mm x 68 mm x 101 mm / 2.24” x 2.72” x 4.04”
EVS200A/EVS200AW
TABLE OF CONTENTS
1. INTRODUCTION....................................................................................................6
2. FEATURES ..............................................................................................................6
3. ACCESSING THE CAMERA MENU ...................................................................7
4. SETTING................................................................................................................10
4.1 SYSTEM INFO ......................................................................................................10
4.1.1 Information .................................................................................................10
4.1.2 Log .............................................................................................................. 11
4.2 USER CONFIG ......................................................................................................12
4.3 NETWORK ...........................................................................................................14
4.3.1 Network.......................................................................................................14
4.3.2 DDNS..........................................................................................................16
4.3.3 Bandwidth ...................................................................................................17
4.3.4 SMTP/FTP ..................................................................................................18
4.3.5 Network Alarm (reserved for PowerCon)...................................................20
4.3.6 Wireless (EVS200AW) ...............................................................................21
4.4 VIDEO .................................................................................................................22
4.4.1 Multi Streaming ..........................................................................................23
4.4.2 Camera ........................................................................................................25
4.5 AUDIO .................................................................................................................25
4.6 USER..................................................................................................................26
4.7 EVENT...............................................................................................................27
4.7.1 Event ...........................................................................................................28
4.7.2 Motion.........................................................................................................31
4.7.3 Alarm...........................................................................................................31
4.7.4 Time Mask ..................................................................................................33
4.8 SYSTEM ............................................................................................................34
4.8.1 Date/Time....................................................................................................34
4.8.2 Daylight Saving ..........................................................................................36
4.8.3 SD Card.......................................................................................................37
4.8.4 Maintenance................................................................................................40
5. SPECIFICATIONS................................................................................................42
EVS200A/EVS200AW
1. INTRODUCTION
The EVS200A/EVS200AW features H.264, MPEG-4 and MJPEG video signals, at
up to 30fps, per channel, over IP networks. The video signals can be received and
displayed with a standard web browser or Nevio Express management software.
The EVS200A/EVS200AW provides Dual Streaming. It is able to generate in total
4 independently configurable H.264, MPEG4 or MJEPG video streams (2 per
input).
The EVS200A/EVS200AW is ultra-compact, so it is perfect for any application that
depends on space-saving solutions. The unit support NTSC/PAL sources and
provide bidirectional audio communication in parallel to video. EVS200AW wireless
model has full support for both Wired Equivalent Privacy (WEP) and Wi-FI Protected
Access (WPA/WPA2) making it one of the most secure wireless network cameras
on the market. EVS200A/EVS200AW is a high performance, two channel solution
that integrates analog cameras into an IP-based video surveillance system.
2. FEATURES
High quality H.264, MPEG-4 and MJPEG multi stream output at 4CIF
resolution @ 60fps
H.264/MPEG4/MJPEG dual stream output per channel for simultaneous
live monitoring and high resolution recording
Smart Wizard settings for varied Event and schedule recording
Support PTZ control
Built-in SD memory card slot for local storage and support SDHC
Two-way Audio
Power over Ethernet (PoE) IEEE 802.3af.
EVS200A/EVS200AW
Ultra-compact size for space-saving applications
3. ACCESSING THE CAMERA MENU
Step 1.Start an Internet Explorer browser.
Step 2. Enter the IP address or host name of the camera in the Location/Address
field of your Internet Explorer browser. (Please refer to EVS200A/EVS200AW
Installation Guide for how to find the IP address)
Step 3. Input “Username” and “Password”. Default Username is “user1” and
default password is “11111111”.
Step 4. Click “Login” button.
Step 5. You might be required to download Active X, which is required to view
camera video. Please click "Yes".
Step 6. Congratulation!! You should be able to see the live image now.
14
EVS [2009/3/5] FPS: 30/30
Live
Playback
Setting
15
Exit
Video Stream
CH1 Stream1
View Size
704 x 480
Digital Zoom
11
10
Manual Control
12
Trigger Event
13
Reset Alarm
EVS200A/EVS200AW
1. Press
button to display the "Live" page.
Double click on the image to show a full screen display, double click again or press
ESC to return normal display.
2. Press Playback button to start playback.
3. Press
button to enter Setting page. In Setting page, there
are 8 sections: [System Info], [User Config], [Network], [Video], [Audio], [User],
[Event] and [System]. Please refer to “4. SETTING” for further information.
4. Press
button to close the network page.
5. Video Stream
Select Video Stream from Stream 1 / Stream 2, Stream 3 and Stream 4. Please refer to
“4.4.1 Multi Streaming” for further information.
6. View Size
You can select View size to either reduce or enlarge the image to the appropriate view
size.
Select the view size for live images from:
NTSC: 704*480/640*480/352*240/320*240/176*120
PAL: 704*576/640*480/352*288/320*240/176*144
7. Digital Zoom
Press “+” or “-“ button to enlarge / reduce the displayed image. (max. is X10)
8. Record
The record button is used to record the current video stream. The location where the
EVS200A/EVS200AW
image file is saved can be specified in Setting -> User’s Config. Please refer to “4.2
User Config” for further information.
Note: Record segment is limited to 1 min. If you need to do long time recording,
please set schedule recording. For more details about schedule recording,
please see “4.7 Event”.
9. Snapshot
The
Snapshot button saves a snapshot of the video image currently being
displayed. The location where the snapshot data is saved can be specified in Setting ->
User’s Config. Please refer to “4.2 User Config” for further information.
10~11. Play Audio/Transmit
Audio
Click the “Play Audio” and “Transmit Audio” buttons to switch the sound off and on
for the speaker and microphone, respectively.
12. Manual Control – Trigger Event
Press “Trigger Event” button to trigger an event directly from live view page, and
event actions will be effective if they have been set in “Event” menu. (Please refer to
“4.7.1 Event”)
13. Manual Control – Reset Alarm
Press “Reset Alarm” button to reset alarm output remotely.
14. Status Display
The name of the camera whose settings currently being configured, current date/time
and current frame rate will be displayed.
15. Event signals
Alarm
Motion
When an alarm or motion event is triggered, a signal icon will flash to alert user.
The first icon is for alarm event and rest of the 5 icons are for motion event. The
motion event icons which differed by colors correspond to the motion trigger areas
you have set in Motion menu. Please refer to “4.7.2 Motion” for detailed information
EVS200A/EVS200AW
about Motion setup.
4. SETTING
Click this button to display the setup menu.
4.1 System Info
System information and system log check of the setup menu can be performed on this
page. The “System Info” page has 2 tabs: [Information] tab and the [Log] tab.
4.1.1 Information
System Information: Firmware version, MAC address, Video Type, Model number.
(unchangeable, for reference only)
10
EVS200A/EVS200AW
4.1.2 Log
System Log:
Date/Time: displaying date and time of the log.
Log message: all information and event message, including login, user’s IP, reboot,
firmware upgrade, load factory default, configuration reset and event detected.
System will keep the newest 256 records.
11
EVS200A/EVS200AW
Press
button to export system log into “.txt” file and select the
location where the exported log file will be saved to.
4.2 User Config
Live view configuration is to be set by user. Each login user can make his/her own
settings for the following items:
Text Setting
Check the box for text of Machine name, Date/Time or Frame Rate to be
displayed on the screen.
Text Color
Foreground Color: Select the foreground color of text to be displayed by moving
the slide bar between Red, Green and Blue until your desire color is obtained.
Position: Select the position where the text will be displaying from Upper Left /
Lower Right / Lower Left.
Press Apply to apply the setting changes or Reset to reset without saving the
12
EVS200A/EVS200AW
change.
Date/Time Format Used in Text
Select Date/Time Format from the following options:
Time Format: 24 Hours or 12 Hours.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Recording/Snapshot Export Setting
Enable Event Recording to PC: Allow event video recorded to users' PC if any
events have been set to record to PC.
Export folder: Select Export folder by clicking on
folder to be exported.
button, then direct to the
File size: Able to limit the size of the single recording file in minutes. When the
single recording file size exceeds the time you set, system will create a new file to
continue recording.
Overwrite: Select “ON” for overwriting recording/snapshot file when the disk
storage capacity is full.
If the remaining hard disk capacity is less than ____ MB (enter the value you wish
to set between 50~2000), system will stop recording or start overwriting.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Language Setting
Language: Select the language to be displayed in web page. Default language is
13
EVS200A/EVS200AW
English. To add a new language which is not listed in the original configuration,
press the Browse button to locate the new language file (.evb) and then click the
Load button.
Note: Upload a new language file will reboot system automatically. Please
reconnect IP camera after reboot.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.3 Network
The network settings and the settings relating to Network, DDNS, Bandwidth,
SMTP/FTP and Network Alarm can be configured on this page.
The "Network setup" page has 5 tabs of the [Network] tab, the [DDNS] tab, the
[SMTP/FTP] tab and the [Network Alarm] tab.
4.3.1 Network
The following information is required to configure the network settings. Contact
14
EVS200A/EVS200AW
the network administrator or your Internet service provider.
• IP Type
• IP address
• Subnet mask
• Gateway (when using the gateway server/router)
• Primary DNS, Secondary DNS (when using DNS)
IP Type
DHCP: Configure the DHCP server not to assign the same IP addresses used for
the other network cameras and PCs whose IP address is unique.
Refer to the network administrator for the settings of the server.
Default: DHCP.
Static IP: User can manually set the static IP for network connection.
PPPoE: This is a DSL connection application, ISP will ask user to input user name
and password.
Note: If PPPoE is used as IP type, IP Utility software will not be able to detect
the device.
IP address
When not using DHCP, enter the IP address of the camera. Do not enter the IP
address already used for PC or other network cameras.
Subnet Mask
This field is to set the netmask for your network so as the IP camera will be
recognized within the network. Example: 255.255.255.000. When DHCP is
selected, the DHCP server will assign this value automatically.
Gateway
This field is to set the gateway for your network so the IP camera will be
recognized within the network. When DHCP is selected, the DHCP server will
assign this value automatically.
Primary DNS
An IP address of DNS server that is provided by ISP.
Secondary DNS
15
EVS200A/EVS200AW
If your ISP provides you an IP address secondary DNS, please set it here.
Username
Enter User name of the account (used only for PPPoE).
Password
Enter Password of the account (used only for PPPoE).
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.3.2 DDNS
DDNS setting
When accessing the camera via the Internet from the network environment of
which the global IP address is obtained using DHCP, the DDNS function is
necessary.
To use the DDNS function, it is necessary to connect to the dedicated DDNS server.
We offer 4 DDNS server providers as follow:
○ www.everfocusddns.com
○ www.sitelutions.com
○ www.dyndns.com
16
EVS200A/EVS200AW
○ www.no-ip.com
Enable: Check the box to enable DDNS setting.
Service ISP: If you choose EverFocus DDNS server, you can obtain a free account
name from EverFocus ”www.everfocusddns.com”.
Enter an IP Cam Account Name:
Press
.everfocusddns.com
button to register or update DDNS account.
If you wish to get a domain name from other DDNS provider, it is necessary to
configure Record ID, FQDN, Username and password and register in DDNS server.
Refer to the web site for further information about the DDNS.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.3.3 Bandwidth
Bandwidth Setting
Max. Bandwidth: Specify, Unlimited / 64 K/ 128 K/ 256 K / 512 K / 1M / 2M / 4M
/ 8M bps. the maximum bandwidth that the camera is allowed to use on the
network. This is a useful function when connecting the camera to busy or heavily
loaded networks. The default setting is Unlimited.
17
EVS200A/EVS200AW
Max. Client Limit: enter a value here to restrict the number of clients accessing the
camera. This is useful if you need to save on bandwidth. Up to 32 clients is
allowed to see live video simultaneously. Subsequent viewers will see a blank
image.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.3.4 SMTP/FTP
Set SMTP
The settings relating to the mail server used to send the e-mail notification from the
camera to predefined addresses via SMTP can be configured.
SMTP Server: Enter the IP address or the host name of the SMTP server used to
send e-mails.
SMTP Port: Enter the port number for SMTP. Default is 25.
Authentication: Check the box, if the SMTP server requires Authentication (user/
password).
18
EVS200A/EVS200AW
User name: Input the login user ID if the SMTP server requires Authentication.
Password: Input the password if the SMTP server requires authentication.
Receiver Address: Input the e-mail address for receiving e-mail message when the
EVENT is enabled and triggered. Please use “;” to separate address.
Sender Address: Input sender’s e-mail address, so that receiver can recognize the
sender when an event message is sent out.
Send Test Mail: Press
address.
button to send a testing mail to the assigned
Set FTP
The settings relating to the FTP server used to transmit the alarm images can be
configured.
FTP Server: Enter the IP address or the host name of the FTP server.
FTP Port: Enter the port number for FTP server. Default is 21.
Recording Path: Assign the recording path.
User Name: Set FTP User’s name.
Password: Set FTP password.
PASV mode: Check to enable Passive mode, normally enable Passive mode. When
failed to establish the connection, uncheck "PASV" mode.
Test FTP Server: Press
FTP server.
button to send a testing file to the assigned
Press Apply to apply the setting changes or Reset to reset without saving the
change.
19
EVS200A/EVS200AW
4.3.5 Network Alarm (reserved for PowerCon)
Set Network Alarm
This function is reserved for PowerCon software, for the detail setting please refer
to PowerCon network alarm protocol.
20
EVS200A/EVS200AW
4.3.6 Wireless
Wireless Setting
Enable Wireless (Default: disable)
SSID: Name of the wireless network the camera is configured for. The field accepts
up to 32 alphanumeric characters. (Default: default)
Network Type: Infrastructure or Ad-Hoc (Default: Infrastructure)
“Infrastructure” Make the Network Camera connect to the WLAN via an Access
Point.
“Ad-Hoc” Make the Network Camera connect directly to a host equipped with a
wireless adapter in a peer-to-peer environment.
Channel: Shows the wireless channel currently in use. (Default: 1)
Security: Disable Security, WEP or WPA-PSK/WPA2-PSK (Default: Disable
Security)
 When selecting WEP:
(WEP (Wired Equivalent Protection) key should follow either one of the following
rules:
- As 5 characters for 64-bit WEP and 13 characters for 128-bit WEP.
- As 10 hexadecimal (0-9, A-F) characters for 64-bit WEP and 26 hexadecimal (0-9,
A-F) characters for 128-bit WEP. )
Authentication: Open or Shared (Default: Open)
“Open” – communicates the key across the network.
21
EVS200A/EVS200AW
“Shared” – allows communication only with other devices with identical WEP
settings.
Key Length: 64 or 128 bits (Default: 64 bits)
Key Format: HEX or ASCII (Default: HEX)
Network Key: Entering a key in either hexadecimal or ASCII format.
Confirm Key: double confirm network key.
 When selecting WPA-PSK/WPA2-PSK:
WPA (Wi-Fi Protected Access) key should follow either one of the following rules:
- As 64 hexadecimal (0-9, A-F) characters.
- As 8 to 63 ASCII characters.
Authentication: AES or TKIP (Default: AES)
Network Key: Entering a key in either hexadecimal or ASCII format.
Confirm Key: double confirm network key
IP Type: DHCP, Static IP (Default: DHCP)
IP Address, Subnet mask, Gateway, Primary DNS, Secondary DNS
Press Apply to apply the setting changes or Reset to reset without saving the change.
4.4 Video
The settings relating video such as streaming, camera OSD can be configured on
this page.
The "Video" page has 2 tabs: the [Multi-streaming] tab and the [Camera] tab.
22
EVS200A/EVS200AW
4.4.1 Multi Streaming
Stream Setting
The system can output 4 video streams simultaneously. For each of them, user can
set compression format, resolution, quality and frame rate individually. Stream 1 is
always enabled for live view.
Check “Enable” box to enable other streams.
Format: Select encode format from H.264, MPEG4 and MJPEG.
Resolution:
NTSC: 4CIF (704*480) / VGA (640*480) / CIF (352*240) / QVGA (320*240) /
QCIF (176*120)
PAL: 4CIF (704*576) / VGA (640*480) / CIF (352*288) / QVGA (320*240) /
QCIF (176*144)
Quality: there are 8 types of quality, please choose from Highest / Higher / High /
Middle / Normal / Low / Lower / Lowest.
Frame Rate: select from NTSC: 1 / 3 / 5 / 15 / 30 fps, PAL: 1/ 2.5/5/12.5/25 fps
23
EVS200A/EVS200AW
Note: Total frame rate cannot exceed 60 fps.
System performance may be influenced if user enables 4 video streams
simultaneously.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Video Recording Setting
User can set video recording by selecting one of the enabled video streamings.
This will allow user to view live images as well as to record video of the other
video streaming.
Video Stream: Select video recording stream from any enabled stream.
Video File format: Recording file will be saved as AVI or ARV, select which file
format to be used.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Note:
1. User can assign one stream for each channel
2. EVS200 should record both channels, specified by the streams here. If not
enough computation power supported, only storing I-frame is allowed.
3. The stream1 of each channel is always enabled to have motion detection feature.
4. Two D1 H.264 compressions for each channel (stream 1) can be supported
computation wise.
5. The stream 1 for each channel allows D1, Half-D1, and CIF. The stream 2 of each
channel allows CIF and QCIF resolution. Basically stream 1 is for storing and
stream 2 requires smaller bandwidth, good for transmission.
24
EVS200A/EVS200AW
4.4.2 Video - Display Setting
Select a channel: add channel selection.
Channel title: add channel title.
PTZ function: select PTZ function ON or OFF
Brightness/ Contrast/Hue: add the adjustment to brightness, contrast and hue
Note: 1. There is no Apply button, whenever the above three picture parameters are
adjusted, the values will be set to the channel
2. Click “Reset” to reload to the original value when just jump into this page
4.5 Audio
The EVS200A/EVS200AW camera can transmit audio to other clients using a built-in
microphone or connecting to external microphone to play audio received from other
clients via connected speakers. This section describes how to configure the basic
audio settings.
25
EVS200A/EVS200AW
Audio
Check Enable Audio box to enable audio function.
Audio Input: Audio from an internal microphone or a line source can be connected
to the Audio connector of EVS200A/EVS200AW. The audio source can be selected
from Internal Microphone, External Audio Input L and External Audio Input R.
Audio Input volume: Adjust the Audio Input Volume for the audio input devices
connected to the camera if there are problems with the sound input being too low
or high.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.6 USER
26
EVS200A/EVS200AW
User Information
Maximum 10 users can be set for using the IP camera. The user information
displays the authorized users and access levels:
• Supervisor/Administrator –a supervisor/administrator has unrestricted access to
the Setting menu and can determine the registration of all other users. However,
administrator is not allowed to change supervisor’s account and password.
• User- a user can view the Live View page, system info, network, video, audio,
and adjust user config settings. The user does not have access to the “user”,
“event” and “system pages”.
• Guest- the lowest level of access, which only allows the user access to the Live
View page.
Note: Please select Active in Status section to activate user account.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.7 EVENT
An event in the camera is when an Event Type is activated and causes certain actions
27
EVS200A/EVS200AW
to be performed. The event type is the set of conditions that specifies how and when
which actions will be performed.
This table describes how to setup action types and event type.
Event Type
Action Type
Alarm Input
Manual
Trigger
Motion
Detection
Schedule
Recording
Trigger Alarm
Send Mail notification
Upload to FTP**
Record to SD Card
Record to PC*
Network Alarm
Re-trigger
Pre/Post-Alarm
Note: 1. * Record to PC only works when PC and IP camera are connected.
2. **Either Upload to FTP or Record to Network Storage can be selected to
record event video to remote site.
3. Up to 10 event types can be configured in the camera, and up to 3 of these
can be configured to upload images.
4.7.1 Event
The settings relating to event occurrences such as settings for the event occurrence,
motion, alarm and time mask can be configured on this page.
The "Event " page has 4 tabs: [Event] tab, the [Motion] tab, the [Alarm] tab and
the [Time Mask] tab.
28
EVS200A/EVS200AW
Press
button to add an event condition.
To modify the event list, click on the event and it will be highlighted. Press
button to modify the setting.
To remove an event from event list, click on the event and it will be highlighted.
Press
button to remove the event.
Check Enable checkbox to activate event actions when the event occurs in the
specified time zone.
To change the priority of events, click on the event and it will be highlighted. Press
or
button to move between events. The event that has
highest priority will be activated first.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
29
EVS200A/EVS200AW
This example describes how to set the camera to upload images to FTP when
someone press Manual trigger button:
button in Event page.
1. Click
2. Enter an event name for the event, e.g. Event 1
3. Select “Manual Trigger” as event type.
4. Select “Upload to FTP” as action type.
5. Check “Enable Pre-alarm Buffer” and “Enable Post-alarm Buffer”. For pre-and
post alarm buffer setting, please refer to “4.7.3 Alarm”.
6. Check “Enable This Event”.
7. Select “Always” for time mask. For detail about Time Mask, please refer to
“4.7.4 Time Mask”.
8. Click
to save this event in event list.
30
EVS200A/EVS200AW
4.7.2 Motion
Motion Detection
First, select the channel for motion detection setting.
User can define the motion area to be detected by left clicking the mouse to draw
lines. Every click is an end point of the line. When the detection area is formed,
double click the mouse to have all the lines connected. To remove the selection,
simply right click the mouse, the selected polygon will be deleted.
Press All Areas to have the entire screen selected for motion detection.
Press Clear to clear all selections.
There are 5 motion trigger areas, which can be distinguished by 5 different colors.
Check Enable checkbox to enable event action.
For each of them, you can set the event action to be activated. Event action can be
set in “Event” section.
Moreover, you can set the Sensitivity level for motion triggered by selecting from
1 (low), 2, 3, 4, 5, 6, 7, 8, 9 to 10 (high).
4.7.3 Alarm
31
EVS200A/EVS200AW
Alarm Output Setting
Contact Type: Normal Close, Normal Open
Duration Time: Select duration time of alarm output from 5 sec, 10 sec, 20 sec, 30
sec, 60 sec, 2 min, 3 min and 5 min.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Pre/Post Alarm Setting
This function is used to check what happened immediately before and after a
trigger, e.g. 5 seconds before or after a motion has been detected.
Pre-Alarm Buffer: Image saved internally in the server from the time immediately
preceding the trigger. Input the desired length of pre-trigger buffer time. It can be
set up to 120 seconds.
Post-Alarm Buffer: Image saved internally in the server from the time immediately
after the trigger. Input the desired length of post-trigger buffer time. It can be set
up to 120 seconds.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Re-trigger Filter Setting
32
EVS200A/EVS200AW
Re-trigger Filter: Set a re-trigger filter time, if another event is triggered during
this time, this triggered event will be ignored.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.7.4 Time Mask
Time Mask Setting
Time mask setting allows you to schedule event actions.
Select Always for event action to be taken continuously.
Press
button to add new time period.
Mask name: Input a mask name for the new time period.
Check the check box for the day to be scheduled: Sun, Mon, Tue, Wed, Thu, Fri &
Sat.
Set the Start time and End time for time mask by clicking Up arrow or Down
arrow. Or simply press
Press
for a full day of event action.
button to remove a scheduled time period.
An example on how to set weekend as time mask is as follows:
33
EVS200A/EVS200AW
1.
2.
3.
4.
Click
from time mask setting.
Enter Mask name, e.g. Weekend.
Check “Sun” & “Sat” boxes.
Select “Start time” and “End time” or “Full day”.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.8 SYSTEM
Date/Time, Daylight Saving, SD card and Maintenance settings can be performed
on this page.
The "System" page has 4 tabs of the [Date/Time] tab, the [Daylight Saving] tab,
the [SD card] tab and the [Maintenance] tab.
4.8.1 Date/Time
Machine Name Setting
Machine Name: Enter the name of the camera. The entered name will be displayed
34
EVS200A/EVS200AW
in the status display area.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Set Time Zone
Time Zone: Select a time zone according to the location where the camera is in
use.
Set Date/Time Manually
Date: Click the calendar and pick the date. Press << to go previous year, < to go
previous month, > to go next month and >> to go next year.
Time: Click on Hour, Minute, Seconds, am/pm; then use up arrow to increase
value and down arrow to decrease value.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Set Date/Time Sync.
Check Enable NTP checkbox to enable NTP server.
NTP server: Time automatically adjusted by synchronizing with NTP server will be
used as the standard time of the camera.
Sync. Internal: Select an interval (1 - 24 hours: in 1 hour intervals) of
synchronization with the NTP server.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
35
EVS200A/EVS200AW
4.8.2 Daylight Saving
Set Daylight Saving
Check Enable Daylight Saving checkbox to enable daylight saving.
Set the start time to daylight saving time.
Set the start week of daylight saving time: 1st / 2nd / 3rd / 4th / Last
Set the start date of daylight saving time: Sunday / Monday / Tuesday / Wednesday
/ Thursday / Friday / Saturday
Set the start month of daylight saving time: January / February / March / April /
May / June / July / August / September / October / November / December.
Set the starting time change of daylight saving time: Choose the “From” time and
“End” time when daylight saving starts.
Set the end time of daylight saving time.
Set the end week of daylight saving time: 1st / 2nd / 3rd / 4th / Last
Set the end date of daylight saving time: Sunday / Monday / Tuesday / Wednesday
/ Thursday / Friday / Saturday
Set the end month of daylight saving time: January / February / March / April /
May / June / July / August / September / October / November / December.
Set the ending time change of daylight saving time: Choose the “From” time and
36
EVS200A/EVS200AW
“End” time when daylight saving ends.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.8.3 SD Card
Setup SD Card
Notification: Notification will be made via e-mail when the remaining space of the
SD memory card reached the value selected from the following.
50%, 20%, 10%, 5%, 2%, 0%
Notes:
‧ When "50%" is selected, e-mail notification will be made each time the
remaining space reaches 50%, 20%, 10%, 5%, 2% and 0%.
‧ E-mail notification may not always be made at a very moment when the
remaining space of the SD memory card reached the selected value.
Event Recording:
FTP backup only: Event video will record to SD card when network is
disconnected.
Normal: Follow the event actions settings you have made in “Event” menu to
37
EVS200A/EVS200AW
record event video to SD card.
Overwrite: Select ON for overwriting data when SD card memory is full. Select
OFF for not overwriting SD card data.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
SD Card Utility
The total size and available size of the SD memory card will be displayed.
Depending on the state of the SD memory card, the size indications will differ as
follows.
Indication Description
Capacity ___ MB, available ___MB, used ___ %
Before formatting the SD memory card, it is necessary to press
Once
button is pressed,
button.
button will be shown for user to
insert the SD card back.
Press
button to format SD card.
Obtain images on the SD memory card
1. Access the camera using the Windows command prompt or FTP client software.
→ The window with the user name and password entry fields will be displayed.
2. Enter the user name whose access level is "1. Administrator" and its password.
→ Log in the camera.
3. A directory of all saved data will be displayed. You are now ready to obtain
images from SD card.
Note:
- It is impossible to access the SD memory card in the process of formatting.
- All data saved on the SD memory card will be deleted when the SD memory
card is formatted.
- Do not turn the power of the camera off in the process of formatting.
38
EVS200A/EVS200AW
4.8.4 Serial Communication
Add Serial Communication setting.
-Channel 1 ID: This entry is used to assign channel 1 camera own ID code.
-Channel 2 ID: This entry is used to assign channel 2 camera own ID code.
-Baud Rate: This field is to set the speed at which is used to transmit instruction or
information through the RS485 port on the camera. There are six different speeds,
2400/4800/9600/19200/38400/57600. (Default: 9600)
-Protocol: Select protocol from EVF, Pelco-D, Pelco-P, Samsung and Panasonic.
(Default: Pelco-D)
-Data Bit: This field is the data bit at which you will be transferring. There are two
settings for this option: 8 or 7. (Default: 8)
-Stop Bit: This field is to set the stop bit for the RS485 connection. There are two
different stop bits, 1 or 2. (Default: 1)
-Parity: This field is to select the parity level at which you will be connected. You can
choose between None, Odd, or Even parity levels. (Default: none)
39
EVS200A/EVS200AW
4.8.5 Maintenance
Maintenance Server
Reboot: The unit is rebooted without changing any of the settings. Use this method
by pressing Reboot button if the unit is not behaving as expected.
Restore: The unit is restarted and most current settings are reset to the factory
default values by pressing Restore button. The only settings saved are:
•
•
IP setting
DDNS setting
Default: The Default button should be used with caution. Pressing this button will
return all of the camera's settings, including the IP address, to the factory default
values. The camera will then have to be re-installed.
Save/Load Configuration Server
To take a backup of all of the configurations, press Save to save all configurations
to a config. file. If necessary, it is then possible to return to the previous settings if
the settings are changed and there is unexpected behavior.
Press the Browse button to locate the saved config. file (see above) and then click
40
EVS200A/EVS200AW
the Load button. The settings will be restored to the previous configuration.
Upgrade Firmware
Upgrade the EVS200A/EVS200AW with the latest firmware.
Press Browse button to search firmware file. Press Upgrade button to upgrade the
firmware.
Note 1: Do not disconnect power to the unit during the upgrade. The unit reboots
automatically after the upgrade has completed. (1-5 minutes.)
2. During upgrading process, all event recording actions will be stopped. It
will continue to record after the camera is rebooted.
41
EVS200A/EVS200AW
5. SPECIFICATIONS
VIDEO STREAMING
Video Compression
Video Resolution
Video Quality
Frame Rate
Video Source
H.264/MPEG-4/M-JPEG
4CIF, VGA, CIF, QVGA, QCIF
8 levels adjustable
Up to 30fps
1 BNC composite, 1 V p-p / 75Ω
NTSC/PAL auto-sense
AUDIO
Compression Method
Operation Mode
NETWORK
IMA ADPCM (Pulse Code Modulation)
2 way audio
Interface
10Base-T/100Base-TX auto-negotiation, RJ-45 socket
Support MDI/MDI-X auto crossover function
Supported Protocols
Bandwidth Control
Max. Client Limit
WIRELESS (EVS200AW)
Standard
Antenna gain
TERMINAL I/O
Alarm Input/Output
Serial Connector
EVENT MANAGEMENT
Event Triggered
Notification
Pre- and Post- Alarm
Buffer
LOCAL STORAGE
SD Card
POWER
Power Supply
Power over Ethernet
Power Consumption
PHYSICAL
Weight
Dimensions
HTTP, TCP / IP, UDP, RTP, RTSP, FTP, SMTP, DHCP, DNS, DDNS,
NTP
Min. 64 kbps adjustable
32 simultaneous clients
IEEE 802.11b/g
2 dBi
1/1
RS-485
Alarm input, Manual trigger, Motion detection and Schedule
recording
Trigger alarm output, Send mail notification, Upload video to FTP,
Record video to SD card, Record video to PC and Network alarm
48MB RAM reserved for pre-alarm record up to 120 sec
Secure Disk physical layer specification version 2.0
Supports SDHC Host Specification
12 VDC
Yes (PoE 802.3af)
4.5W max.
300g / 0.66lbs
77 (W) x 38 (H) x 117 (D) mm / 3” (W) x 1.5” (H) x 4.6” (D)
With Antenna:
77 (W) x 102 (H) x 153 (D) mm / 3” (W) x 4” (H) x 6” (D)
ENVIRONMENTAL
Operating Temp.
0°C ~40°C / 32°F~104°F
Humidity
(20%~80% Humidity)
42
EVS200A/EVS200AW
EverFocus Electronics Corp.
Head Office:
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chi, Taipei, Taiwan
China Office:
Room B-05D-1, KESHI PLAZA, Shangdi
Information Industry Base,Haidian
TEL: 886-2-26982334
FAX: 886-2-26982380
www.everfocus.com.tw
District, Beijing China
100085
TEL: +86-10-62973336/37/38/39
FAX: +86-10-62971423
USA Office:
1801 Highland Ave. Unit A
Duarte, CA 91010, U.S.A.
www.everfocus.com.cn
Europe Office:
Albert-Einstein-Strasse 1
D-46446 Emmerich, Germany
TEL: 49-2822-9394-0
FAX: 49-2822-939495
TEL: +1-626-844-8888
FAX: +1-626-844-8838
www.everfocus.com
www.everfocus.de
USA N.Y. Office:
415 Oser Avenue Unit S
Hauppauge, NY 11788
Tel: 631-436-5070
FAX: 631-436-5027
www.everfocus.com
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Japan Office:
1809 WBG Maribu East 18F,
2-6 Nakase.Mihama-ku.
Chiba city 261-7118, Japan
TEL: 81-43-212-8188
FAX: 81-43-297-0081
www.everfocus.co.jp
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
43
®
EverFocus

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2009:08:13 10:02:04Z
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2009:09:28 09:35:36+08:00
Metadata Date                   : 2009:09:28 09:35:36+08:00
Format                          : application/pdf
Creator                         : hazel
Title                           : Microsoft Word - EVS200A_manual_draft.doc
Producer                        : GPL Ghostscript 8.15
Document ID                     : uuid:b8dfab7e-a0e6-47a9-a75d-482e2b9ab4cf
Instance ID                     : uuid:aa02459a-1330-4701-a3d3-a9efb7f04053
Has XFA                         : No
Page Count                      : 43
Author                          : hazel

EXIF Metadata provided by EXIF.tools