Everfocus Edsr100H Users Manual MSR1G0191A

EDSR100H to the manual 28cc82c8-4b5b-4a21-9c74-529dfdfd58f8

2015-02-02

: Everfocus Everfocus-Edsr100H-Users-Manual-427180 everfocus-edsr100h-users-manual-427180 everfocus pdf

Open the PDF directly: View PDF .
Page Count: 55

EDSR100H

INSTRUCTION MANUAL

Digital Single Channel Recorder

About this manual

Before installing and using this unit, please read this Manual carefully.

Be sure to keep it handy for later reference.

V1.0

?Refer all work related to the installation of this product to qualified service

personnel or system installers.

?Do not block the ventilation opening or slots on the cover.

?Do not drop metallic parts through slots.This could permanently damage

the appliance. Turn the power off immediately and contact qualified service

personnel for service.

?Do not attempt to disassemble the appliance.To prevent electric shock,

do not remove screws or covers. There are no user-serviceable parts

inside. Contact qualified service personnel for maintenance. Handle the

appliance with care. Do not strike or shake, as this may damage the

appliance.

?Do not expose the appliance to water or moisture, nor try to operate it in

wet areas. Do take immediate action if the appliance becomes wet.

Turn the power off and refer servicing to qualified service personnel.

Moisture may damage the appliance and also cause electric shock.

?Do not use strong or abrasive detergents when cleaning the appliance

body. Use a dry cloth to clean the appliance when it is dirty. When the

dirt is hard to remove,use a mild detergent and wipe gently.

?Do not overload outlets and extension cords as this may result in a risk of

fire or electric shock.

?Do not operate the appliance beyond its specified temperature, humidity

or power source ratings. Do not use the appliance in an extreme

environment where high temperature or high humidity exists. Use the

appliance at temperature within 0oC ~ +40oC and a humidity below 90%.

The input power source for this appliance is AC100~240V.

Safety Precautions

WARNING

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Notice:

The information in this manual was current when published. The manufacturer

reserves the right to revise and improve its products. All specifications are

therefore subject to change without notice.

Safety Warning

Note:

This is a class A product. In a domestic environment this product may cause radio interference

In which case the user may be required to take adequate measures.

Note:

This equipment has been tested and found to comply with the limits for a Class A digital device,

The changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

The exclamation point within an equilateral triangle is

intended to alert the user to presence of important operating

and maintenance(servicing)instructions in the literature

accompanying the appliance.

Warning :

To prevent fire or shock hazard, do not expose units not

specifically designed for outdoor use to rain or moisture.

Safety Precautions

The lightning flash with an arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the presence

of uninsulated ”dangerous voltage ”within the product’s enclosure

that may be of sufficient magnitude to constitute a risk of electric

shock to persons

Attention:

Installation should be performed by qualified service personnel only

in accordance with the National Electrical Code or applicable local codes.

Power Disconnect:

Units with or without ON-OFF switches have power supplied to the unit

whenever the power code is inserted into the power source; however, the

unit is operational only when the ON-OFF switch is in the ON position.

The power cord is the main power disconnect for all units.

External Power Supplies

Use only the recommended power supplies.

Power supplies must comply with the requirement of

the latest version of IEC 60065/CNS 13439. Substitutions

may damage the unit or cause a fire or shock hazard

AC100V~240V Power Cords

AC100V~240V power cords

Warning:

Electrostatic-sensitive device. Use proper

CMOS/MOSFET handing precautions to avoid

electrostatic discharge.

Service

If the unit ever needs repair service, the customer

should contact the nearest Everfocus Electronics Corp.

Service Center for return authorization and shipping

instruction.

Safety Precautions

Important Safeguards

Read Instruction---All the safety and operating instructions should be read before the init is operated

Retain Instructions---The safety and operating instructions should be retained for future reference.

Heed Warnings—All warnings on the unit and in the operating instructions should be adhered to.

Follow Instructions—All operating and use instructions should be followed

Cleaning—Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.

Use a damp cloth for cleaning

Attachments—Do not use attachment not recommended by the product manufacturer as they may cause hazards.

Water and Moisture—Do not use this unit near water-for example, near a bath tub, wash bowl, kitchen sink,

or laundry tub, in a wet basement, near a swimming pool, in an unprotected outdoor installation, or any area which is

classified as a wet location.

Servicing— Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified service personnel.

Power Cord Protection—Power supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, playing particular attention to cords and plugs, convenience receptacles, and the point

where they exit from the appliance.

Object and Liquid Entry—Never push objects of any kind into this unit through openings as they may touch dangerous

voltage points or short-out parts that could result in a fire or electric shock, Never spill liquid of any kind on the unit.

Important Safeguards

Table of Contents

1. Product Overview……….…...……………………………………………………………………………………..………….. 1

1.1 Feature………...…….…….… .…………………………………….…………..……………………………………………..1

1.2 Specifications………....………………….………………………………..………….………….…………………………...2

2. Front & Rear Panels………...…….………………………………………..…………………………………………………....3

3. Back Panel Connections…….………...……………………………………..…………………………………………………..5

4. System Connection…....………………………...…………………………..…………….…………………….………………..8

4.1 One Camera Connection………….… ..…….………………………………………………………..……………………….8

4.2 Multiplexer Connection...……….… .………………………………………………...……………...………………………..9

4.3 Quad Connection ( with VCR )………….……………….…………………….…………………..……………………… 10

4.4 Quad Connection ( without VCR)… .… .………….……………...……………………………………………………...… .11

5. Installation………...………………………………………………...……………….….………………………………………12

6. Menu………...……………….……………………………………..……………………………………………………………13

6.1 Clock/Language Setup… ...………….…………….… .………………………………………………………….………….14

6.2 Daylight Setting Menu..……..……………...…….……….………………………...……………………….……………...15

6.3 Timer Setting Menu……………….…….……....…………………………………………………...…………………..… .16

6.4 Normal Record Setting Menu…………………….……....……………………………………………………………...… .18

6.5 Alarm Record Setting Menu……………………….………………..………………………………………………………20

6.6 Buzzer Setting Menu…………………….… .…………….…………………………...…………………………………….25

6.7 Archive Setting Menu… ....………….…………...……………..……………………………………………………………26

6.8 RS232/RS485 Setting Menu……………….………………………………..……………………………………………….27

7. Recording…...……………...……………………………………………………………..……………………………………. 31

7.1 Instant Recording……………..…………………………………………………….……………………………………... 31

7.2 Alarm Recording…………………………………………….………………………………….………………………….. 32

8. Playback…...…………………………………………………….……………………….…………………………………..…33

8.1 Normal Playback…………………………………………………………………………………………………………... 33

8.2 Search Playback…………………………………………………………………………………………………………… 35

9. Copy………...……………………….…………………………………………………………….…………………….………38

9.1 Still Image Copy……………………………………………………………………………………………………………38

9.2 Copy to Movie File……...………………………………………………………………………………………………….39

10. Interface Specifications……..….……...……………………………………………………………………………………...41

10.1 Transmission setting……..……………………………..………………………….………………………………………41

10.2 Remote Control Protocol…………………………………..………………………………………………………..……..42

11. Remote Controller………….…….……………………………………………………………………………...……………45

12. Appendix-A/Time Lapse Mode Recording Time…….……..………………………………………………………....….....46

12.1 Recording with 80 GB HDD… ..……..………...………………….…………………………………………….………..46

12.2 Recording with 160 GB HDD…………..………..……………………………………………………………………….47

13. Appendix-B/ Security Lock setting..…...…….………………………………………………………………………………48

6.9 System Setting Menu…………………………………………………………………………………………………………28

1. Product Overview

The Digital Video Recorder is the first true VCR replacement designed particularly for the security industry,

seamlessly combining high-resolution video multiplexing and digital recording.

The Digital Video Recorder at speeds up to 60/50 fields per second with NTSC/PAL formats and replay event

instantly.

The Digital Video Recorder incorporates all the benefits of digital video recording, is simple to install, and operates

just like a VCR. The highly efficient compression technology, as well as the superior clarity and detail of recorder images,

make the Digital Video Recorder stand out from its competitors as the best choice for security surveillance.

1.1 Features

Product Overview and Features

Digital Recording provides superior quality images

Hard-disk hot-swapping capability

Pre-Alarm image recording

Compatible with most multiplexers

Time lapse and real time recording

Refresh rate up to 60 fps (50 fps for PAL)

Quick Search by date/time, alarm events, and recording list

Fast and slow playback of recorded video in various speeds

On-screen setup menu and system timer

Multi-level password protection

RS-232/RS-485 communication port

Highly stable non-PC based proprietary system

Built-in M-JPEG compression/decompression with configurable quality

Audio recording capability

Programmed with various time-lapse speeds, Data can be stored in Compact Flash Card.

Operation status record log

Specifications

0℃~+40℃Operating Temperature

320.8mm (L) x 215mm (W) x 100mm (H) Dimension

AC100~240VPower Source

Yes Watch Dog Timer

Built-in real time clock Timer

Front Panel Keypad User Input Device

Menu Driven User Interface

On screen display setup Setup

By Date/Time or Event or Segment Playback Search

60/50 fps for NTSC/PAL Playback Rate

60/50 fps for NTSC/PAL Recording Rate

Continuous, Time -lapse recording,

Timer or Event Recording

Recording Mode

3.5”IDE type, Hot-swappable Hard Disk Storage

Yes Event Log

9-pin female connectorRS-232

Yes Video Loss Detection

2 inputs; 2 outputs Audio

Yes Alarm Output

Yes Alarm Input

Yes, Built-in Compact Flash card slot CompactFlash Memory

720x484 (NTSC); 720x576 (PAL) Video Resolution

M-JPEG Video Compression

1 video output (BNC), 1Vpp/75ohmVideo Output

1 video input with loop through (BNC),

1Vpp/75ohm

Video Input

1.2 Specifications

Power Consumption 39W

RS485 RJ11 Connector

20 10

912

11 13 14 16 21

1817

Front Panel Keypads

1 4

2. Front Panel Keypads

21 43 568 7

LOCK:Press and hold the LOCK button over 3 seconds to lock/unlock the function keys of the front panel.

This function is used to avoid unexpected contact with the panel.

6BUZZER:Press this key to turn On/OFF the buzzer for all events.

5ENTER:

8MENU: Press this key to enter Setup menu.

STOP : Press this key to stop recording and play back.

PAUSE: Press this key to pause the playback picture.

SEARCH: Press this key to enter the Search Playback Menu.

REC : Press this key to start recording.

COPY: Press this key to start copy still picture or video stream into Compact Flash card.

REV. PLAY : Reverse Play Back.

PLAY: Play Back.

KEY

Left/Right Button: Press or to move the cursor to the left or right

Up/Down Button: Press or to change the value.

Press this key to confirm the selection or data changed.

EDSR100H

Display: Press this key to switch ON/OFF.

Display OFF Display Date/Time

And Operation status

Jog and Shuttle Dial

Shuttle : In Playback mode,turn the shuttle dial can fast forward/rewind the picture.

In Pause mode, turn the shuttle dial can slow forward/rewind the picture.

Jog Dial :In Pause mode, turn the Jog dial can stop forward/backward the picture.

In Menu mode, turn the Jog dial can change menu page forward/rewind.

Compact Flash Card Slot: Insert a Compact Flash Card.

Hard Disk Tray: Hard Disk holder for HDD.

LEDs: LEDs for system active, power and ALARM access.

Remote Control: IR Remote receiver

HDD KEY: Protect HDD without steal

Record

002HR

Disk:120 GB(0)

2003/04/24 10:41:00

Display Date/Time,

Operation Status,

Disk Status.

Record

002HR

Disk:120 GB(0)

Disk size:120GB

2003/04/24 10:41:00

MUX MAIN

MONITOR IN

Back Panel Connections

Audio IN : Audio input for recording.

Audio OUT : These two audio outputs can be set to “Enable”or “Disable”in Setup Menu.

The operation of audio out is as follows:

When in recording or standby mode,

the out of SW1 is connected to Audio IN.

Playback Audio

When in playback mode the out of SW1 is

connected to SW2 Audio.

When Playback Audio is enabled then the output

of SW2 will be connected to Playback Audio.

When Playback Audio is disabled then there is no

audio output (MUTE).

When Audio Out is enabled and machine is in Recording or Standby mode, the Audio IN is loop-through to Audio Out

connector.

When Audio Out is enabled and machine is in Playback mode then the Audio Out playback audio.

AUDIO

549

Operation of SW1 : Operation of SW2 :

Audio IN

Audio OUT

OFF / Mute SW1

SW2

( Internal circuit )

3. Back Panel Connections

10 3 8

POWER

1Power in: The main power in.

VIDEO IN : The BNC connectors of video input enables the system to receive the signals from

each camera through the 75 ohm coaxial cables.

VIDEO IN /Output

VIDEO OUT(1~2) : Connect the other devices with four cameras to the other devices.

MUX MAIN MONITOR: Video input BNC connector, connected to multiplexer main monitor output.

MAIN

MONITOR MONITOR OUT

INTERNAL

VIDEO

SW3

When the machine is in Menu, Search or Copy mode, the internal Video is switched to Monitor Out, so that the user

can view full screen OSD. In other modes, the Video from multiplexer main monitor will be loop-through to the Monitor

Out.

MONITOR

Back Panel Connections

( Internal circuit )

4MONITOR : Video output BNC connector connected to main monitor.

ALM-OUTPUT : Normal Close Alarm output. In normal condition, this terminal is

shorted to the terminal of ALM -COM. In alarm status, it is open

between ALM-NC and ALM-COM terminals.

ALM-INPUT : Normal Open or Normal Close type alarm sensor input.

The Alarm Input can be selected as Normal Open or Normal Close input in the setup

menu. When an alarm occurs, alarm recording will automatically start.

Alarm Input/ Output

6VIDEO LOPPING : The loop-through composite video input can be connected to other devices.

RS232

RS232 connector : Connect D-Sub 9 pins connector to RS232 ports for remote control8

Back Panel Connections

RS485

RS485 connector : Cascade multi Digital Video Recorder.9

10 FAN: Cooling FAN.

MUX MAIN

MONITOR IN

4.1 One Camera Connection.

(1 ) :Video out:

The Camera Video Output is connected to the Video In at the rear panel.

Main Monitor

(2 ) : Audio Out:

The camera audio output is connected to the audio input terminal at the rear panel.

(3) : System Main Monitor Output:

The main monitor is connected to the VIDEO OUT 1 BNC connector.

System Connection

(1)

(2)

(3)

Note: Please set the Multiplexer item to OFF . (NORMAL RECORD SETTING MENU)

4. System Connection

MUX MAIN

MONITOR IN

(1): Multiplexer VCR Out :

This connects to the VIDEO IN connector at the rear panel.

(2) :Multiplexer VCR In :

This connects to the VIDEO OUT 1 connector at the rear panel.

(3) :Multiplexer Main Monitor Output:

This connects to the MUX. MAIN MONITORIN IN connector at the rear panel.

(4) :System Main Monitor Out:

Connect the MAIN MONITOR OUTPUT connector to the main monitor.

System Connection

4.2 Multiplexer Connection.

Main Monitor

Multiplexer

(3) (2) (1)

(4)

VCR IN VCR OUT

MAIN MONITOR OUTPUT

Note: Please set the Multiplexer item to ON . (NORMAL RECORD SETTING MENU)

MUX MAIN

MONITOR IN

4.3 Quad Connection. ( Quad with VCR in VCR out connector)

Main Monitor

Quad

(1): Quad VCR Out:

This connects to the VIDEO INPUT connector at the rear panel.

(2) : Quad VCR In:

This connects to the VIDEO OUTPUT connector at the rear panel.

(3) : Quad Main Monitor Out:

This connects to the MUX. Main connector at the rear panel.

(4) : System Main Monitor Output:

Connect the MAIN MONITOR OUTPUT connector to the main monitor.

System Connection

(1)

(2)

(3)

VCR IN VCR OUT

MAIN MONITOR OUTPUT

(4)

Note: Please set the Multiplexer item to ON . (NORMAL RECORD SETTING MENU)

MUX MAIN

MONITOR IN

4.4 Quad connection. ( Quad without VCR in VCR out connector)

Main Monitor

(1): Quad Video Out ( to Video Recorder):

This connects to the VIDEO INPUT connector at the rear panel.

(2): System Main Monitor Output:

Connect the MAIN MONITOR connector to the main monitor.

System Connection

Quad

VIDEO OUT

(1)

(2)

Note: Please set the Multiplexer item to OFF . (NORMAL RECORD SETTING MENU)

INSTALLATION

(1) Insert a HDD (IDE) for Video Storage

The HDD should be set as MASTER.

( Normally the default setting of HDD is Master)

Notice:After the hard disk case is inserted into the hard disk tray, be sure to

Turn the tray key in lock position. Otherwise, hard disk will not be detected and

The System Loading procedure can not be completed.

(2) Connect cable for video/audio input and video/audio out,

The detail connection is described in SYSTEM CONNECTION.

(3) Switch Power On

The POWER LED lights if power is normal.

(4) Press MENU key to enter SET UP MENU.

Once inside the main menu you will find there are

nine set up pages as below:

(5) Turn the jog dial clockwise or counterclockwise to change set up page.

1. CLOCK/LANGUAGE SETTING MENU

2. DAYLIGHT SAVE SETTING MENU

3. TIMER SETTING MENU

4. NORMAL RECORD SETTING MENU

5. ALARM RECORD SETTING MENU

6. BUZZER SETTING MENU

7. ARCHIVE SETTING MENU

8. RS232/RS485 SETTING MENU

9. SYSTEM SETTING MENU

5. Installation

6. MENU FLOW

TIMER SETTING MENU

( See page 16 )

DAYLIGHT SETTING MENU

( See page 15 )

CLOCK/LANGUAGE

SETTING MENU

( See page 14 )

Turn the Jog dial clockwise or counterclockwise to change

setting menu page.

: 2003/04/24 TUE

: 13:01:02

CLOCK/LANGUAGE SETTING MENU

DATE

TIME

MENU LANGUAGE : ENGLISH

TIMER SETTING MENU

WEEK

SUN

START STOP SPEED QUALITY SET

00:00 00:00 002 HR STABDARD OFF

NORMAL RECORD

SETTING MENU

( See page 18 )

NORMAL RECORD SETTING MENU

SPEED

QUALITY

MULTIPLEXER

DISK FULL

: 002

: STANDARD

: OFF

: REWRITE

ALARM OPERATION

RECORDING SPEED

RECORDING QUALITY

ALARM –IN TYPE

ALARM -RESET TYPE

ALARM DURATION TIME

PRE-ALARM OPERATION

RECORDING SPEED

ALARM RECORD

SETTING MENU

( See page 20 )

OFF

888888

002 HR

STANDARD

N.O.

05 SECS

002 HR

PICTURE SIZE

TIME STAMP

TIME STAMP POS

WATER MARK

WATER MARK POS

BUZZER

SETTING MENU

( See page 22 )

SYSTEM SETTING MENU

( See page 25 )

SYSTEM SETTING MENU(V1.0 05/19)

PLAY WITH AUDIO 1

PLAY WITH AUDIO 2

PASSWORD ENABLE

PASSWORD

FIELD CODE LINE

DISK RENEW

SYSTEM UPDATE

LOAD DEFAULT

CF RENEW

ALARM RECORD SETTING MENU

BUZZER SET SETTING MENU

BUZZER

ALARM –IN

RECORD -IN

DISK FULL

VIDEO LOSS

TIMER

: ENABLE

: ON

ARCHIVE SETTING MENU

( See page 23 )

ARCHIVE SETTING MENU

: 720 X 480

: ON

: BOTTOM

: ON

: BOTTOM

RS232/RS485 SETTING MENU

( See page 23 )

RS232/RS485 SETTING MENU

DAYLIGHT SETTING MENU

DAYLIGHT SAVING :OFF

START ON JAN 1ST MON

FROM 00:00 TO 00:00

END ON JAN 1ST MON

FROM 00:00 TO 00:00

RS232/RS485 :RS232

RS232/RS485 ID :01

BUAD RATE :9600

PARITY :NONE

DATA BIT :8

STOP BIT :2

In CLOCK/LANGUAGE SETTING MENU , we SET

(1) DATE : Current date

Year: 2000 ~ 2099 Month: 01~ 12 Date: 01~31

(2) TIME : Current time

Hour: 00 ~ 23 Minute : 00 ~ 59 Second: 00 ~ 59

(3) MENU LANGUAGE: ENGLISH

CLOCK/LANGUAGE SETTING MENU

DATE

TIME

MENU LANGUAGE

: 2003/04/24 TUE

: 13:01:02

: ENGLISH

6.1 CLOCK/ LANGUAGE SETTING MENU

Left/Right Button: Press or to move the cursor to the left or right

Up/Down Button: Press or to change the value.

VERSION: 1.0 (2003/05/26)

6.2 DAYLIGHT SETTING MENU

DAYLIGHT SETTING MENU

DAYLIGHT SAVING: OFF

START ON JAN 1ST MON

FROM 00:00 TO 00:00

END ON JAN 1ST MON

FROM 00:00 TO 00:00

In DAYLIGHT SETTING MENU , we define:

(1) DAYLIGHT SAVING:

Select “ON”or “OFF”while the daylight saving time function is enabled or not.

(2) START ON:

“1ST”Use the arrows to set the present week

1ST 2ST 3ST 4ST

“SUN”Use the arrow to set the present date

Thursday

Sunday Friday

TuesdayMonday Wednesday Saturday

“JAN ”Use the arrow to set the present month

Sunday February March

January April May June

December

November

October

SeptemberAugust

July

“FROM”00:00 “TO”00:00: Use the arrow to set the start time value.

LAST

Left/Right Button: Press or to move the cursor to the left or right

Up/Down Button: Press or to change the value.

6.3 TIMER SETTING MENU

TIMER SETTING MENU

WEEK START STOP SPEED QUALITY SET

SUN 00:00 23:59 002 HR STANDARD OFF

The monitored image can be recorded automatically by setting the start and end

times in TIMER SET SETTING MENU, we can set the schedule to record for a whole week.

(1) WEEK:

This selects the day for the timer .Records each day’s schedule.

(2) START:

This key is used to start the timer recording.

(3) STOP:

This key is used to end the time for recording.

In TIMER SETTING MENU, we define

(4) Speed :

When SPEED FORMAT is set to HOUR, the recording speed

can be set from 2/3 (NTSC/PAL)HR to 960HR.

When SPEED FORMAT is set to IPS, the recording speed can

be set from 1~60/1~50(NTSC/PAL)IPS.

(5) QUALITY:

Picture Quality

There are six quality levels for recording

(6) SET:

Set “ON”when using timer recording.

Set “OFF”when not using timer recording

LOWER

LOW

BASIC

STANDARD

HIGH

SUPERIOR

15 KB

20 KB

25 KB

30 KB

35 KB

40 KB

NORMAL RECORD SETTING MENU

SPEED

QUALITY

MULTIPLEXER

DISK FULL

002 HR

STANDARD

OFF

REWRITE

In NORMAL RECORDING MENU, we define

(1) SPEED : Recording Speed

The user can select the record ing speed from 2/3 (NSC/PAL) HR to 960 HR.

(2) QUALITY:Picture Quality

There are six quality levels for recording

LOWER

LOW

BASIC

STANDARD

HIGH

SUPERIOR

15 KB

20 KB

25 KB

30 KB

35 KB

40 KB

6.4 NORMAL RECORD SETTING MENU

(3) MULTIPLEXER:

ON/OFF : The user can select Multiplexer connection or One Camera connection

ON : The video input from MUX MAIN MONITOR connector at the rear

panel will be looped through to the main monitor out when the

recorder is not in MENU mode.

OFF : The main monitor output is similar to the video out connector.

(4) Disk Full:

STOP : When the disk is full, the machine will STOP recording.

REWRITE : When the disk is full, the current video will OVERWRITE the exis ting video

from the beginning of HDD.

Left/Right Button: Press or to move the cursor to the left or right

Up/Down Button: Press or to change the value.

In ALARM RECORDING MENU, we define

(1) ALARM OPERATION :

ON : Records when alarm occurs.

OFF : Does not record when alarm occurs.

(2) RECORDING SPEED : The recording speed in alarm duration.

The max. recording speed is 2/3 (NTSC/PAL) HR.

The min. recording speed is 960 HR.

(3) RECORDING QUALITY :

Select the Recording picture quality when alarm occurs.

LOWER

LOW

BASIC

STANDARD

HIGH

SUPERIOR

ALARM RECORD SETTING MENU

ALARM OPERATION

RECORDING SPEED

RECORDING QUALITY

ALARM –IN TYPE

ALARM -RESET TYPE

ALARM DURATION TIME

PRE-ALARM OPERATION

RECORDING SPEED

003 HR

STANDARD

N.O.

05 SECS

003 HR

15 KB

20 KB

25 KB

30 KB

35 KB

40 KB

6.5 ALARM RECORD SETTING MENU

(4) ALARM –IN TYPE :

N.O. : Normal Open,

N.C. : Normal Close

(5) ALARM -RESET TYPE:

N.O. : Normal Open,

N.C. : Normal Close

(6) ALARM DURATION TIME :

Alarm recording starts from the beginning of alarm and stops at the end of the duration.

The max. duration is NON -STOP, the min. duration is 5 Seconds.

(7) PRE-ALARM OPERATION :

ON : Record the picture in pre -alarm recording speed in pre-alarm period.

OFF : No pre -alarm recording before alarm occurs.

(8) RECORDING SPEED :

This is the recording speed in the pre-alarm period.

The max. recording speed is 2/3 (NTSC/PAL) HR.

The min. recording speed is 960 HR.

(9) PRE –ALARM TIME :

The duration of pre -alarm recording period

In 2/3 hour Real Time recording mode, the duration of pre-alarm is about five seconds.

Notice :

If the alarm occurs when it is in standby mode or in normal recording mode,the recording quality will be the

same as the normal recording quality.

If the alarm occurs when it is in timer recording mode , the recording quality will be the same as the value

set in timer recording quality.

Left/Right Button: Press or to move the cursor to the left or right

Up/Down Button: Press or to change the value.

Note: Alarm Connectors (DB-15)

PIN # NAME PIN # NAME

1 GND 9 GPOUT

2 ALARM 10 DISK_FULL

3 RECIN 11 VD_LOSS

4 NC1 12 VCR_SW

5 NC2 13 ALM_NC

6 ALMRST 14 ALM_NO

7 GPIN 15 ALM_COM

8 GND

The alarm connector, figure 1, is used to provide one

sensor alarm input for each camera input.

For easy operation, an alarm extension board,

figure 2, is provided to connect to the alarm

connector.

Each alarm input requires two wires, one wire

connects to the desired alarm input pin, the

second wire connects to the multiplexer

ground. The alarm signal assignment is shown

at the following table, table 1.

915

PSR1D0080A

8 7 6 5 4 3 2 1

9 10 11 12 13 14 15

Normally Closed Connection (use pin # 13 and # 12)

82 1

15 9

COIL

RELAY

To external

equipment

(a.) Alarm out

To external

equipment

82 1

COIL

RELAY

There are two ways to do the alarm out connection:

To external

equipment

82 1

15 9

COIL

RELAY

Normally open connection (use pin # 13 and # 14)

Alarm in

There is one alarm input. Please connect the alarm input in the same sequence as the

camera input BNC.

When alarm signal comes in, the Digital Video Recorder will do the following:

1. Display Alarm Message

2. Turn on the buzzer if the buzzer setting is on.

The ALARM in can be selected as normally open input or normally closed input:

Normally Open : If the alarm input is selected as Normally Open input, then the

(N.O.) input is opened normally, and shorted to the ground means an alarm happens.

Normally Close : If the alarm input is selected as Normally Close input, then the

(N.C.) input is shored to the ground normally, and opened input means an alarm

happens.

There is 1 alarm sensor in for 1 channel and 1 alarm reset in, the

alarm input can be set to Normally Open or Normally Closed by user.

SENSOR 1

8 2 1

ALARM RESET

ALARM

CIRCUIT

BUZZER SETTING MENU

BUZZER

ALARM –IN

RECORD -IN

DISK FULL

VIDEO LOSS

TIMER

In BUZZER SETTING MENU, we SET the buzzer ON/OFF under the following conditions:

(1) BUZZER :

ENABLE: Turns the buzzer on.

DISABLE: Turns the buzzer off.

User can press Enter button to enable/disable in Record/Playback mode.

(2) ALARM –IN :

ON, the buzzer will sound when the alarm occurs.

(3) RECORD –IN:

ON, the buzzer will sound when Record-IN signal is applied on the Record-IN terminal.

(4) DISK FULL :

ON, the buzzer will sound when disk is near full 99.7%

(5) VIDEO LOSS :

ON, the buzzer will sound when the video loses.

(6) TIMER :

ON, the buzzer will sound when timer record occurs.

: ENABLE

: ON

6.6 BUZZER SETTING MENU

Left/Right Button: Press or to move the cursor to the left or right

Up/Down Button: Press or to change the value.

ARCHIVE SETTING MENU

PICTURE SIZE

TIME STAMP

TIME STAMP POS

WATER MARK

WATER MARK POS

MULTIPLEXER

720x576

BOTTOM

NONE

6.7 ARCHIVE SETTING MENU

(1) PICTURE SIZE :

Selects picture size for copying image to CF card

Big size:720x576

Small size:352x288

(2) TIME STAMP :

ON: The time stamp will show on the picture when copying image to CF card.

OFF: The time stamp will not show on the picture when copying image to CF card.

(3) TIME STAMP POS:

BOTTOM: The time stamp will show on the bottom

TOP: The time stamp will show on the top

(4) WATER MARK:

ON: Shows a water mark on the picture when copying image to CF card.

OFF: This erases the water mark on the picture when copy image to CF card.

(5) WATER MARK POS:

BOTTOM: Water mark will show on the bottom

TOP: Water mark will show on the top

(6) MULTIPLEXER:

Multi-brand of multiplexer for user choose: NONE/EVERFOCUS 4BDX/EVERFOCUS 4CDX/EVERFOCUS

16CTX/ROBOT MU99P/APPRO MPX-9016/DM NPRITE4 /ATV QSP-860MPX

Left/Right Button: Press or to move the cursor to the left or right

Up/Down Button: Press or to change the value.

(1) RS232/RS485: Choose RS232 or RS485 for activated.

(2) RS232/RS485 ID: This entry is used to assign each device with its own ID code, when more than on unit is

used in one system through RS232/RS485.

There are two ID code for the Digital video recorder : 001 or 002

(3) BAUD RATE: There are 6 different speeds that can be used to transmit instruction or

information through the RS232/RS485 port on the device, 1200 baud,2400 baud,4800 baud,9600 baud,

19200 baud,and 3840 baud. The default setting from the factory is 9600 baud.

(4) PARITY: Select parity lever: NONE/ODE/EVEN

(5) DATA BIT: Select data bit : 8 or 7

(6) STOP BIT:Select stop bit: 1 or 2

RS232/RS485 SETTING MENU

6.8 RS232/RS485 SETTING MENU

RS232/RS485

RS232/RS485 ID

BAUD RATE

PARITY

DATA BIT

STOP BIT

In the RS232/RS485 SETTING MENU, we define

: RS232

: 01

: 9600

: NONE

: 8

: 2

Left/Right Button: Press or to move the cursor to the left or right

Up/Down Button: Press or to change the value.

(2) PASSWORD ENABLE :

YES/NO : User can set the PASSWORD ON or OFF to enter the system setting menu.

YES:Selects the PASSWORD to enter the system setting menu .

NO:Turns off the PASSWORD to enter the system setting menu.

(3) PASSWORD :

When selecting YES for PASSWORD ENABLE, to unlock key a password

is required. The code is six digits long and can be a digit from 1 to 8.

Once you have activated the password, whenever you press the LOCK button for unlock

the system will ask you to enter the password.

Therefore, be sure to make a note of the password.

SYSTEM SETTING MENU

PLAY WITH AUDIO 1

PLAY WITH AUDIO 2

PASSWORD ENABLE

PASSWORD

FIELD CODE LINE

DISK RENEW

SYSTEM UPDATE

LOAD DEFAULT

CF RENEW(FAT16)

OFF

888888

PASSWORD: ******

6.9 SYSTEM SETTING MENU

(1)PLAY WITH AUDIO 1

PLAY WITH AUDIO 2 :

ON/OFF : Play back with or without audio.

(5) DISK RENEW :

YES/NO : Activates the Renew HDD option.

DISK RENEW

NO YES Press NO to renew HDD and Press ENTER key to Exit.

NO YES

DISK RENEW Press Yes to Renew HDD and Press ENTER key to Exit.

(6)SYSTEM UPDATE :

YES/NO : Updates the system.

YES : Copy the update files into Compact Flash card ON PC and insert the

Compact Flash card into the slot, and then press ENTER key to update system.

The “Reading Program………”will be shown on the screen during the process.

The “Success”will be shown on the screen after system update.

Notice: After the system is updated successfully, be sure reboot the system.

(4) FIELD CODE LINE : When the system is connected to the Multiplexer, it is used to adjust the field code

of the Multiplexer.

The values: 00~20

The default value is 13, it is suitable for most of the multiplexers.

If the field code line appears on the top of each playback channel, decrease the value.

If multiplexers can not playback properly ,increase the value.

(8)CF RENEW:

Two of modes for choice, YES or NO.

NO: will not format CF card

YES: will format CF card

(7)LOAD DEFAULT :

LOAD DEFAULT

NO YES Press NO to load default and Exit.

LOAD DEFAULT

NO YES Press YES to load default value.

Left/Right: Press or to move the cursor to the left or right

Up/Down: Press or to change the value.

CF RENEW

NO YES

CF RENEW

NO YES

7.1 INSTANT RECORDING

When pressed, the pictures being monitored

will be recorded in the HDD.

•The recording rate and recording quality are

set in the Record Set menu

•“ REC ”button light up in the operating

display

Video out

Press Stop key to stop recording.

•Stop key can be activated only in recording mode.

•When the HDD is full, the machine will Stop recording automatically

or Overwrite from the beginning of the HDD. It depends on the

setting in HDD setting

Press Record key to start the recording immediately.

Recording

REC

STOP

RECORD

002 HR

Press MENU key and turn the jog dial to select the ALARM

RECORDING SETTING MENU.

The monitor image will automatically record when alarm occurs and stopsrecording at the end of the alarm

duration period.

Instant recording and timer recording will stop when an alarm occurs.

RECORDING OPERATION:

ON: Enables alarm recording,

OFF :Disables alarm recording.

RECORDING SPEED:

Set the recording speed when alarm occurs.

RECORDING QUALITY:

In alarm duration, the recording quality can be set which is different from instant or timer recording.

ALARM –IN TYPE:

Select the type of alarm-in input to be Normal Close (N.C.) or Normal Open (N.O.)

ALARM –RESET TYPE:

Select the type of alarm-reset input to be Normal Close (N.C.) or Normal Open (N.O.)

ALARM DURATION TIME:

Alarm duration from 5 seconds to NON –STOP.

PRE-ALARM OPERATION:

ON: Enables pre-alarm recording,

OFF: Disables pre-alarm recording.

RECORDING SPEED:

Set the recoding speed in pre-alarm duration.

Notice:

The recording quality in pre-alarm duration is the same as recording quality before alarm occurs. If the recorder

is not recording before alarm occurs, the recording quality in pre-alarm duration will be the same as instant

recording quality.

Recording

7.2 ALARM RECORDING

8.1 NORMAL PLAYBACK

Press the PLAY key to start playing back the stored image/audio from

the last SEGMENT.

(1) Playback

Press the REV.PLAY key to start reverse playing back the stored

image/audio from the last segment.

Press the STOP key to stop playing back.

(3) Fast Forward/Reverse Playback

Press the PLAY key to start playing back.

Turn the shuttle dial clockwise and fast forward playback starts.

The speed will be shown on the LCD at the right upper corner of the screen.

>> 2, 4, 6, 8, 16, 32, 600X

Turn the shuttle dial counterclockwise and fast reverse playback starts.

The speed will be shown on the LCD.

<< 2, 4, 6, 8, 16, 32, 600X

Playing Back

REV.PLAY

PLAY

STOP

(2) STOP

Playing Back

(5) Frame/Field advance Forward/Reverse

Press PAUSE key to freeze the picture.

Turn the jog dial clockwise to advance the still image Frame/Fie ld by

Frame/Field .

Turn the jog dial counterclockwise to rewind the still image Fra me/Field by

Frame/Field .

The Frame/Field feed speed will increase if the jog dial is turned quickly.

PAUSE

(4)Slow Forward/Reverse Playback

Press PAUSE key to freeze the playing back picture.

Turn the shuttle clockwise and slow forward playback starts.

The speed will show on the LCD at the corner of the screen.

>> 1/2, 1/4, 1/6, 1/8, 1/10, 1/16, 1/32

Turn the shuttle counterclockwise and slow reverse playback starts.

The speed will show on the LCD at the corner of the screen.

<< 1/2, 1/4, 1/6, 1/8, 1/10, 1/16, 1/32

PAUSE

8.2 SEARCH PLAYBACK

(1) Segment Search Playback

Press the SEARCH key to enter the Search menu.

SEARCH MENU

BY SEGMENT LIST

BY ALARM LIST

BY DATA TIME

Press the keys to move the cursor to BY SEGMENT LIST and press ENTER key to

select file search.

SEGMENT SEARCH

Playing Back

Press the keys to move the cursor to the segment you want to playback. Press

Enter to select the segment.

When the selection list is full, turn the jog dial clockwise to select next page list for search

other list.

After the starting time is confirmed, press Enter to start playing back.

Alarm

Timer

2002/04/24 19/03/29

2002/04/25 12/30/30

2002/05/20 12/00/00

Alarm:ALARM RECORD

Timer: TIMER RECORD

Playing Back

(2) Alarm Search Playback

Press SEARCH key to enter the Search menu.

Press the keys to move the cursor to BY ALARM LIST and press ENTER

key to select alarm search.

ALARM SEARCH

Press the keys to move the cursor to select the alarm image to be played back.

When the selection list is full, turn the jog dial clockwise to select next page for search

other list.

The alarm image will be played back from the pre-alarm period and stop at the end of alarm

duration.

SEARCH MENU

BY SEGMENT LIST

BY ALARM LIST

BY DATE TIME

2002/04/24 19/03/29

2002/04/25 12/30/30

2002/05/20 12/00/00

Alarm

Timer

Alarm : PRE-ALARM RECORD

Timer : TIMER RECORD

Playing Back

(3) Date/Time Search Playback

Press SEARCH key to enter the Search menu.

Press the keys to move the cursor to BY DATE/TIME and press ENTER key to

select file search.

DATE/TIME SEARCH

YEAR/MM/DD HH:MM:SS

2002 04 24 19 03 35

Notice: If there is no image stored in the date/time specified then the machine will

start playing back from the nearest set time automatically.

Press the keys to move the cursor.

Press the keys to increase/decrease the data.

Press Enter and the playback starts from the date/time set in the menu.

SEARCH MENU

BY SEGMENT LIST

BY ALARM LIST

BY DATE/TIME

COPY

Insert a Compact Flash card into the Compact Flash slot on the front panel.

When inserting the Compact Flash card, make sure that the direction of insertion is

correct.

Press the PAUSE key to freeze the picture.

Turn the jog dial clockwise or counterclockwise to move to your desired

image of choice .

PAUSE

Press the PLAY key to start playing back.

PLAY

COPY

While the image to be displayed as your desired image of choice ,

press the COPY key. The “Copying …”will be shown on the screen during

the process. The “Success”will be shown on the screen after file copied

Notice: Copied images are stored as a single picture.

Copied files are saved as .JPG file.

9.1 STILL IMAGE COPY

9. COPY

EDSR100H

COPY

Press COPY key and then the copy menu appears.

COPY

Press the PLAY key to start playing back.

PLAY

PLAY Press PLAY key to continue Copy Movie File.

COPY TO MOVIE FILE

Press COPY

Press PLAY

Press PAUSE

Press SEARCH

Press STOP

To Step Copy

To Continue Copy

To Stop Continue

To End Copy

To End Play

9.2 COPY TO MOVIE FILE

COPY

Press the PAUSE key to stop continue copy.

PAUSE

Press STOP key to end play.

STOP

Notice: Copied images are stored as a movie picture.

Copied files are saved as .MOV file.

Use QuickTime to play the retrieved .MOV files.

You may download QuickTime at www.apple.com.

The playback version for QuickTime is free.

SEARCH Press SEARCH key to end copy.

Interface Specifications

RS232

10.1 Transmission setting

The pin assignment of the 9-pin D-SUB connector

PIN # NAME PIN # NAME

1 NOT CONNECTED 1 NOT CONNECTED

2 TXD 2 RXD

3 RXD 3 TXD

4 NOT CONNECTED 4 NOT CONNECTED

5 GROUND 5 GROUND

6 NOT CONNECTED 6 NOT CONNECTED

7 NOT CONNECTED 7 NOT CONNECTED

8 NOT CONNECTED 8 NOT CONNECTED

9 NOT CONNECTED 9 NOT CONNECTED

Digital Video Recorder HOST

D-SUB 9-pin connector specifications

This Digital Single Channel Recorder may be controlled by a computer or a terminal via

the standard D-SUB 9-pin RS-232 connector.

There are 6 different speeds that can be used to transmit instruction or

information through the RS232/RS485 port on the device, 1200 baud,2400 baud,4800 baud,9600 baud,

19200 baud,and 3840 baud.

The default setting from the factory is 9600 baud.

Please refer to Chart 6.11 (page27) for details.

Interface Specifications

10.2 Remote Control Protocol

A computer or a terminal can be used to control the unit by sending the packet as following.

=========================================================

Digital Video Recorder 485/232 Control Code Protocol

=========================================================

1-1. Sample control code packets

Example1 : A packet that send "REC" key to Digital Video Recorder(ID=5)

0x85 (length)

0x00 (Receiver ID high byte)

0x05 (Receiver ID low byte)

0x4B (OPcode = key )

0x08 (DATA1 = "Rec"keycode )

0x5D (checksum)

Example2 : A packet that send "PAUSE" key to Digital Video Recorder(ID=4999)

0x85 (length)

0x27 (Receiver ID high byte)

0x07 (Receiver ID low byte)

0x4B (OPcode = key )

0x0C (DATA1 = "Pause" keycode )

0x0A (checksum)

Example3 : A packet that send "PLAY" key to all Digital Video Recorder (broadcast)

0x85 (length)

0x7f (Receiver ID high byte)

0x7f (Receiver ID low byte)

0x4B (OPcode = key )

0x0B (DATA1 = "Play" keycode )

0x59 (checksum)

2-1. The format of message packet is as follows:

Length Byte (Prefix: 0x86, 0x87, or 0x88 ..... )

Receiver ID high byte

Receiver ID low byte

Opcode Byte

Data Byte1

Data Byte2

Data Byte3

Checksum Byte

2-2. Length Byte

This Length Byte is also a prefix. Bit7 must be 1.

EX: 0x87 ==> this packets has 7 bytes length. ( not included Length byte itself )

2-3. Receiver ID

1). Individual receiver ID

---------------------------------------------------------------------

Decimal 14bit binary value Hbyte Lbyte Receiver ID (Digital Video Recorder)

------- ------------------- ------ ------ ----------------------

00000000 0000000 00 00 ID = 0

10000000 0000001 00 01 ID = 1

20000000 0000010 00 02 ID = 2

....

126 0000000 1111110 00 7e ID = 126

127 0000000 1111111 00 7f ID = 127

128 0000001 0000000 01 00 ID = 128

129 0000001 0000001 01 01 ID = 129

255 0000001 1111111 01 7f ID = 255

256 0000010 0000000 02 00 ID = 256

....

511 0000011 1111111 03 7f ID = 511

....

16382 1111111 1111110 7f 7e ID = 16382

---------------------------------------------------------------------

2). Broadcast ID

---------------------------------------------------------------------

Decimal 14bit binary value Hbyte Lbyte Receiver ID (Digital Video Recorder)

------- ------------------- ------ ------ ----------------------

16383 1111111 1111111 7f 7f all DVR connect to RS485

---------------------------------------------------------------------

2-4. Opcode Byte & Data bytes

2-4-1. OPcode

------------------------------------------

OPcode Data1 Function

------ ------ --------------------------

0x4B Keycode A remote key pressed

------------------------------------------

2-4-1. A remote key pressed (OPcode=0x4B)

---------------------------------

Data1 Key

------ -------------------------

0x00 key 'LEFT'

0x01 key 'RIGHT'

0x02 key 'UP'

0x03 key 'DOWN'

0x04 key 'ENTER'

0x05 key 'BUZZER'

0x06 key 'LOCK'

0x07 key 'MENU'

0x08 key 'REC'

0x09 key 'REV.PLAY'

0x0A key 'STOP'

0x0B key 'PLAY'

0x0C key 'PAUSE'

0x0D key 'SEARCH'

0x0E key 'COPY'

0x0F key 'DISPALY'

0x10 key 'SHUTTLE << x2"

0x11 key 'SHUTTLE << x4"

0x12 key 'SHUTTLE << x6"

0x13 key 'SHUTTLE << x8"

0x14 key 'SHUTTLE << x16"

0x15 key 'SHUTTLE << x32"

0x16 key 'SHUTTLE << x600"

0x17 key 'SHUTTLE >> x2"

0x18 key 'SHUTTLE >> x4"

0x19 key 'SHUTTLE >> x6"

0x1a key 'SHUTTLE >> x8"

0x1b key 'SHUTTLE >> x16"

0x1c key 'SHUTTLE >> x32"

0x1d key 'SHUTTLE >> x600"

0x1e key 'JOG<'

0x1f key 'JOG>'

---------------------------------

2-5. Checksum Byte

Checksum is computed as the sum of all previous byte(including the

length byte), then mask with 0x7f.

Remote Controller

Figure 1

(Optional)

11. Remote Controller

The remote controller is an accessory to enhance the

handy operations of digital video recorder (Figure 1).

You can do all the settings and operations by the remote

controller. The effective distance is up to 10 meters

without any obstacles. The keypad functions are as

same as the front panel of the digital video recorder .

Appendix-A

12.1 When Recording with 80-GB HDD

Lower

Low

Basic

Standard

High

Superior

: 15 kB

: 20 kB

: 25 kB

: 30 kB

: 35 kB

: 40 kB

(Estimated with typical image-low noise level)

12. APPENDIX-A/Time Lapse Mode Recording Time

NTSC (system storage:80GB)

Recording Recording

Speed Rate

(Hour) (field/Sec)

2 60 24H 18H 14H 12H 10H 9H

6 15 98H 74H 59H 49H 42H 37H

12 8.571 172H 129H 103H 86H 74H 64H

24 4.615 321H 240H 192H 160H 137H 120H

48 2.4 617H 463H 370H 308H 264H 231H

72 1.622 913H 685H 548H 456H 391H 342H

96 1.224 1210H 907H 726H 605H 518H 453H

168 0.706 2098H 1573H 1259H 1049H 899H 786H

480 0.249 5949H 4462H 3569H 2974H 2549H 2231H

720 0.166 8924H 6693H 5354H 4462H 3824H 3346H

960 0.125 11851H 8888H 7111H 5925H 5079H 4444H

PICTURE QUALITY

LOWER LOW BASIC STANDARD HIGH SUPERIOR

PAL (system storage:80GB)

Recording Recording

Speed Rate

(Hour) (field/Sec)

3 50 29H 22H 17H 14H 12H 11H

616.667 88H 66H 53H 44H 38H 33H

12 10 148H 111H 88H 74H 63H 55H

24 5.556 266H 200H 160H 133H 114H 100H

48 2.941 503H 377H 302H 251H 215H 188H

72 2 740H 555H 444H 370H 317H 277H

96 1.515 977H 733H 586H 488H 419H 366H

168 0.877 1689H 1266H 1013H 844H 724H 633H

480 0.311 4763H 3572H 2858H 2381H 2041H 1786H

720 0.207 7156H 5367H 4294H 3578H 3067H 2683H

960 0.156 9646H 7122H 5698H 4748H 4070H 3561H

PICTURE QUALITY

SUPERIORHIGHSTANDARDBASICLOWLOWER

Reference:24H=1 day.168H=1 week, 720H=1 month,8760H=1 year

12.2 When Recording with 160-GB HDD Lower

Low

Basic

Standard

High

Superior

: 15 kB

: 20 kB

: 25 kB

: 30 kB

: 35 kB

: 40 kB

Appendix-A

(Estimated with typical image-low noise level)

PAL (system storage:160GB)

Recording Recording

Speed Rate

(Hour) (field/Sec)

3 50 59H 44H 35H 29H 25H 22H

616.667 177H 133H 106H 88H 76H 66H

12 10 296H 222H 177H 148H 127H 111H

24 5.556 533H 400H 320H 266H 228H 200H

48 2.941 1007H 755H 604H 503H 431H 377H

72 2 1481H 1111H 888H 740H 634H 555H

96 1.515 1955H 1466H 1173H 977H 838H 733H

168 0.877 3378H 2533H 2027H 1689H 1447H 1266H

480 0.311 9527H 7145H 5716H 4763H 4083H 3572H

720 0.207 14313H 10735H 8588H 7156H 6134H 5367H

960 0.156 18993H 14245H 11396H 9496H 8140H 7122H

PICTURE QUALITY

LOWER LOW BASIC STANDARD HIGH SUPERIOR

Reference:24H=1 day.168H=1 week, 720H=1 month,8760H=1 year

Appendix-B

13. APPENDIX-B/SECURITY LOCK SETTING

Press LOCK key, the system will ask for the password. If you enter

a correct password, the locked keys will be released.

LOCK

Press LOCK key during record mode, then all the keys on the

front panel will be locked.

(Password must be Enable on System Setting Menu)

EverFocus Electronics Corp.

Head Office:

12F, No.79 Sec. 1 Shin-Tai Wu Road,

Hsi-Chi, Taipei, Taiwan

TEL : 886-2-26982334

FAX : 886-2-26982380

USA Office:

2445 Huntington Drive, San Marino,

CA 91108, U.S.A.

TEL : 1-626-844-8888

FAX : 1-626-844-8838

Toll free : 1-888-383-6287 or

1-888-EV-FOCUS

Japan Office:

1809 WBG Marive East 18F,

2-6 Nakase.Mihama-ku.

Chiba city 261-7118, Japan

TEL : 81-43-212-8188

FAX :81-43-297-0081

Beijing Office:

Room 609, Technology Trade Building,

Shandgdi Information Industry Base,

HaidianDistrict, Beijing,China

TEL : 86-10-62971096

FAX : 86-10-62971432

European Office:

Albert-Einstein-Strasse 1

D-46446 Emmerich, German

TEL : 49-2822-9394-0

FAX : 49-2822-939495

EverFocus®

P/N:MSR1G0191A

Everfocus Edsr100H Users Manual MSR1G0191A

EDSR100H to the manual 28cc82c8-4b5b-4a21-9c74-529dfdfd58f8

Navigation menu

Versions of this User Manual:

Views

Navigation