Everspring Industry Co FE001 Wireless Handsfree Headset Kit User Manual scan 6

Download:
Mirror Download [FCC.gov]
Document ID	141220
Application ID	msR7fA6ebgU6yLnARwA6+w==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.82kB (260297 bits)
Date Submitted	2001-03-21 00:00:00
Date Available	2001-03-21 00:00:00
Creation Date	2001-01-31 03:48:29
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	2001-01-31 16:43:54
Document Title	穨scan-6.PDF
Document Creator	穨scan
Document Author:	穨ivy

EXHIBIT C
User Manual
DIGITALKI WIRELESS HANDSFREE KIT
USER’S GUIDE
Congratulations and thank you for choosing DIGITALKI, an advanced
wireless hands-free kit to enhance your mobile communication DIGITALKI
is designed and produced to meet the highest quality standards. DIGITALKl
will bring you a great convenience when using your mobile phone.
DIGlTALKI also will minimize your exposure to radio frequency (RF) from
your mobile phone, Please read this User's Guide before operating your
DlGITALKL '
GENERAL INFORMATION
DIGITALKI hands-free kit is an accessory to a specific model of mobile phone‘
Please check the compatibility before using this device. The complete
DIGITALKI kit includes the following items:
1 ONE HEADSET
Face:
On I O" Swim
Battery Charge Comm
24 TWO DETACHABLE EAR HOOKS 3. ONE PLUG ADAPTER
(Necessary only for specific
models.)
Let! 4— 7 —’ Right
\\‘
4. ONE INTERFACE MODULE 5. ONE AC/DC ADAPTER
Built—in NuI hr BeII Clip
Connector Plug
to Mobile Phone
Battery Compartment
SETTING UP THE UNITS
NOTICE: PLEASE CHARGE THE HEADSET & INTERFACE MODULE
FOR APPROXIMATELY 2 HOURS BEFORE USING YOUR DIGITALKI.
YOUR DIGITALKI I3 READY FOR USE WHEN CHARGER'S LED TURNS
GREEN.
STEP 1. SELECT AND INSTALL THE EAR HOOK
Choose the right or Iefl ear hook by your preference. Snap the ear hook into
the socket on the Headset as shown in Fig. 1A To wear headset, follow Fig. 2A
The ear hook is slightly flexible to fit your ear contour for wearing comfort.
To remove ear hook, simply pull the ear hook plug off the Headset
@ eee
Fig, 1 Fig. 2
STEP 2. ACTIVATE THE "AUTO ANSWER” MODE OF YOUR MOBILE
PHONE
STEP 3. CONNECT INTERFACE MODULE TO
YOUR MOBILE PHONE
Plug the Interface Module connector to your
mobile phone. Your mobile phone will display
‘hand-free" or similar phrase on its panel to
confirm a good connection
STEP 4. BELT CLIP (Option)
Fasten the belt clip to the Interface Module by screwing into the built-in nut
(see Fig. 4 or 5).
Note: If you wish to attach the lntertace Module to the back of your mobile
phone by the magnet piece, you will need to remove the belt clip first.
STEP 5. CHARGING THE BATTERIES
Your Headset and Interface Module each has a Nth rechargeable battery
pack inside. When the LED in the front cover of your Headset stam flickering
during standby mode, charge both the Headset and the Interface Module at
your earliest convenience. To charge the 2 devices. connect them to the
charger and adapter as shown in Fig. 6 and 7 (the 2 devices can be charged
at the same time).
a fie
Fig 6 Fig. 7
The smaller plug pin is for charging the Headset and the bigger plug pin is for
the Interface Module. When batteries are fully charged, the LED will turn
green automatically.
6. AUDIO QUALITY ADJUSTMENT
On the top of the Interface Module. you will find
a 3-level selection switch for audio quality
adjustment (see Fig. 8). Make a test call to
your mobile phone, and use a ball pen tip to
And-K, WWW switch among the 3 positions to select the best
audio quality for your phone.
Note: You won't need to adjust the switch again
until you use the kit with a mobile phone of a
different brand/model.
Fig. 8
OPERATIONS
1. RECEIVING AND MAKING A CALL
Before receiving or making any call, make sure you have already connected
the Interface Module to your mobile phone.
RECEIVE A CALL
When your phone receives a fill, it will ring 2~3 times before it answers
automatically. After the ringing stops, lightly press the onloff switch once to
receive the call and start talking.
Note: You may start operating the Headset only after the ringing stops. When
your conversation ends, the Headset will turn off automatically.
MAKE A CALL
Make a call direct from your phone, and when the all is answemd, lightly press
the onloff switch to talk.
DIGITALKI does not support voice dial function.
HOLD YOUR CALL
When necessary, you may press the onloff switch once to hold your call. and
press again to resume the conversation.
ADJUST SPEAKER VOLUME DURING A CALL
You can adjust the speaker volume during a call by pressing the 4-level volume
control buttons on the side of the Headset to tone upldown according to your
preference.
2. OPERATION RANGE
DIGITALKI is a very low power communication device. The radio
communication range between the Headset and the Interface Module is
approximately 10 meters. Please keep both units within this range for best
communication performance.
Note: If the communication distance exceeds 10 meters during any call, the
Headset will send out a warning beep to remind you.
3. TROUBLE SHOOTING:
If the Headset cannot communicate throth to your mobile phone please
check the following:
in Headset
Interface Module low
3. RF codes of the Headset and Plug both devices to the charger at
Interface Module do not match the same time to -air u - the codes
IMPORTANT MESSAGES
When entering areas (e.g. hospitals and aircrafl) where usage of mobile
phones is prohibited by law, please turn off both your mobile phone and
DIGITALKI. ‘
As high temperature will shorten the battery life, please do not leave your
DIGITALKl and your mobile phone in an environment with temperatures over
14D“F, for example on the dash board of your car during summer. Also,
keep your DIGITALKI and your mobile phone away from moisture.
Use soft cloth with mild liquid soap to clean the exterior of your DIGITALKI.
DO NOT use abrasive chemical detergent or material to clean your
DlGITALKl,
Do not attempt to pry open the cover of your DIGITALKI or change the
batteries. Seek assistance from an authorized DIGITALKI dealer near you.
For optimal standby and operation time, we recommend that you use only the
specific battery packs supplied by the authorized DiGlTALKI dealer
WARRANTY SCOPE AND DURATION
Everspn‘ng guarantees our products (excluding the batteries) as being free of
defects in material. design and workmanship at the time of original purchase
and for a period of twelve (12) months immediately thereafter.
If, during the warranty period, the products maifuncfion in normal use and
service (by authorized dealer). Everspring or its authorized dealer will repair
'or replace the defective product at no cost to the original purchaser
presenting a valid warranty certifiwte.
Everspring or its authorized dealer may refuse to provide free warranty
service if any of the following conditions occurs:
1. The warranty certificate is altered, illegible, or with inconsistency.
2. The product is adapted, modified, or charged.
3. The product exterior is cracked or broken
4. The serial number label is tempered with or missing.
Repair or replacement wills neither give any right to extend the original
warranty period nor give any right to start a new warranty period. Replaced
faulty parts or components will become the property 01 Everspring.
.............................. x...-.--_.-.-.-....-.-.....-...
WARRANTY REGISTRATION
_____—_-————
[DEVICE CODE
SERIAL NUMBER
DATE or PURCHASE
PURCHASER :
ADDRESS
_‘l5~<:
DEALER |NAME2
CODE:
R EMARKS:

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Creator                         : .穨.scan
Create Date                     : 2001:01:31 03:48:29
Title                           : .穨.scan-6.PDF
Author                          : .穨.ivy
Producer                        : Acrobat PDFWriter 4.0 for Windows
Modify Date                     : 2001:01:31 16:43:54+08:00
Page Count                      : 7

EXIF Metadata provided by EXIF.tools