Everspring Industry Co H202M Wireless Alarm System, Magnetic Contact Detector User Manual H302W

Download:
Mirror Download [FCC.gov]
Document ID	407436
Application ID	E5cTW2tE4ZK4vJXfUybKRg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	117.16kB (1464530 bits)
Date Submitted	2004-03-23 00:00:00
Date Available	2004-03-19 00:00:00
Creation Date	2004-03-18 14:30:29
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2004-03-18 14:30:29
Document Title	Microsoft Word - H302W
Document Creator	PScript5.dll Version 5.2
Document Author:	gracelin

H302W
10-Zone Wirefree Alarm System
Installation & Operating
Manual
Copyright ©2003 All Right Reserved.
CONTENTS
KIT CONTENTS
EXTERNAL CONNECTIONS
14
INTRODUCTION AND OVERVIEW
Multiple Users
System Arming
Zones
Entry/Exit Delay
Quick Set
Final Exit Set Zone
Walk Through Zone
Omit Zone
Zone Lockout
Event Log
Chime
Voice Dialer
Digital Dialer
Latch-Key
Answer-Phone
Voice Memo
Remote System Control
Tamper Protection
Jamming Detection
Battery Monitoring
System House Code
TESTING THE SYSTEM
Initial Testing
Testing an Installed System
15
15
15
DEFAULT SETTINGS
Reset Factory Default
16
17
PROGRAMMING
User Setup
System Setup
Zone Setup
Voice Dialer Setup
Arm Status Setup
Part-Arm 1 Setup
Part-Arm 2 Setup
Latch Key Setup
Home Control Setup
Answer Phone Setup
Digital Dialer Setup
18
18
20
23
25
28
29
29
30
31
33
33
PLANNING AND EXTENDING YOUR
WIREFREE ALARM SYSTEM
REMOTE CONTROL UNIT
General Information
Setting the Remote Control
CONTROL PANEL
Locating the Control Panel
Mounting the Control Panel
Setting the Control Panel
Testing the Control Panel & Remote Control
OPERATION INSTRUCTIONS
Operating Instructions
Arm
Part-Arm 1
Part-Arm 2
Disarm
Quick Set
Omit Zone
Panic Alarm
Tamper
Chime
Event-Log
Voice Memo
Replay Messages
Remote System Control
Connection to Home Automation Modules
Battery Monitoring
36
36
36
36
36
36
37
37
37
37
37
37
38
38
38
39
39
MAINTENANCE
40
ALARM RECORD
41
TROUBLESHOOTING
42
DIGITAL DIALER TRANSMISSION
PROTOCOL
43
PASSIVE INFRA-RED DETECTORS
Choosing a Mounting Location
Installing the PIR Detectors
Setting the PIR Detectors
Testing the PIR Detectors
10
10
11
MAGNETIC CONTACT DETECTORS
Choosing a Mounting Location
Installing the Magnetic Contact Detectors
Setting the Magnetic Contact Detectors
Testing the Magnetic Contact Detectors
11
12
12
13
13
KIT CONTENTS
The Alarm System should contain the following
components.
1 x LCD Control Panel
1 x PIR Detector
1 x Magnetic Contact Detector
1 x Remote Control
Also included:
Power Supply Adaptor
Telephone Connection Lead
Installation & Operating Manual
Fixing pack
H302Q LCD Control Panel
Batteries
2 x 6V/1.2Ahr Sealed lead acid battery
1 x 9V PP3 Alkaline battery
3 x 3V CR2032 Lithium
H302P PIR Detector
IMPORTANT
Please check all items as mentioned above are
included in the package.
COMMON ACCESSORIES FOR CONTROL
PANELS
The following accessories are compatible with a series
of Everspring’s alarm systems as below:
Control Unit
Compatible Accessories
H302W, H302Y, HA65U
H302P PIR Detector
H202M Magnetic Contact Detector
H302R Remote Control
H202M Magnetic Contact
Detector
H302R Remote Control
INTRODUCTION AND OVERVIEW
MULTIPLE USERS
The system allows for up to 6 Users and a Master User
to be configured. This allows the system Event Log to
maintain a record of which users have armed and
disarmed the system. Each user will have a different
Password. In addition a 4 second voice recorder
facility enables the users name to be recorded for use
with the Latch-Key facility.
Only the Master User has access to the programming
functions and is able to configure the system.
Note: Any Remote Control Units on the system will be
recorded as User 6.
SYSTEM ARMING
The system has a full ‘Arm’ and two ‘Part-Arm’ modes.
ARM will ‘Arm’ all zones while the ‘Part-Arm’ modes will
only arm the zones that are enabled for the particular
part-arm mode.
For example:
The system could be configured such that during night
time, ‘Part-Arm 1’ would arm only zones protecting the
lower floor and outbuildings leaving the upper floor free
for movement without triggering the alarm.
During the day while the property is occupied ‘Part-Arm
2’ would arm only the zones protecting the outbuildings.
However, when the property is left un-occupied, the full
‘Arm’ mode will arm all zones to protect the entire
property, (i.e. upper and lower floors and outbuildings).
ZONES
The system incorporates 6 wireless Alarm Zones for
the connection of the system detectors that are used to
independently monitor different areas of the property.
In addition to standard intruder protection, each zone
may also be configured to operate in one of four other
modes:
‘PANIC/PA’ mode provides 24 hour monitoring of
any Personal Attack (PA) switches incorporated
into the system.
‘24-hour Intruder’ mode provides 24 hour intruder
protection for areas/zones where continuous
monitoring is required, (e.g. gun lockers).
triggered an entry will be recorded in the Event
Log but an alarm will not occur.
In addition there is the facility to connect 4 hard wired
zones to the Control Panel, each of which is fully
configurable with the same features as the wirefree
zones (1-6).
ENTRY/EXIT DELAY
When the system is armed with the Exit-Delay enabled,
no alarm signal from any detector on an active zone will
be able to initiate an alarm until the Exit-Delay has
expired. This enables the system to be armed from
within the property and allows time for the user to exit
the property without triggering an alarm.
If the
Exit-Delay is disabled then detectors on active zones
will immediately be able to initiate an alarm as soon as
the system begins to arm.
The system Exit-Delay may be configured for between
10 to 250 seconds or disabled completely.
If a detector on a zone with its Entry-Delay enabled is
triggered, then an alarm condition will not occur until
the Entry-Delay period has expired. This allows time
for the user to re-enter the property and disarm the
system before an alarm condition occurs. Generally
only the zones on the main entry route to the property
will be configured with an Entry-Delay. The remaining
zones would be configured with their Entry-Delay
disabled allowing them to immediately initiate an alarm
a detector on the zone is triggered.
The Entry-Delay for each zone may be configured for
between 10 to 250 seconds or disabled completely.
QUICK SET
The system may be fully armed in 5 seconds using the
quick set facility, overriding the programmed exit-delay.
This is useful for setting the system at night when the
exit-delay warning beep will be silenced after just a few
seconds.
FINAL EXIT SET ZONE
Triggering a detector on a Final Exit zone during the
exit-delay will cause the delay to reset to 5 seconds
with the system arming 5 seconds later.
WALK THROUGH ZONE
‘Fire’ mode provides 24 hour monitoring of any
Fire/Smoke detectors incorporated into the system.
‘Test’ mode allows a zone to be monitored while the
This feature may be used for detectors located on the
main entry route to the Control Panel. When the
system is armed and a zone configured as a ‘Master
Walk Through’ zone is triggered, the zones Entry-Delay
will start. Any zones configured as ‘Slave Walk
system is armed. If a detector on a test zone is
Through’ will be disabled to allow free access to the
Control Panel to disarm the system before the
entry-delay expires an alarm occurs.
If access is gained via a zone that is not configured as
‘Master Walk Through’, the ‘Slave Walk Through’ zones
will operate as normal according to their programmed
Entry-Delay setting.
Note: A zone set as a ‘Master Walk Through’ zone
must be configured with an Entry-Delay.
messages for the configured ‘Play Time’. The recipient
must acknowledge the message by pressing the
button on their telephone keypad. If the call is
unanswered or an acknowledgment is not received
then the next active number in the dialing sequence will
be called. The dialer will continue calling each
number in turn until either all numbers in the sequence
have been dialed the set number of times or the
sequence is cancelled/acknowledged by the recipient.
DIGITAL DIALER
OMIT ZONE
A zone may be temporarily omitted when the system is
armed using the Omit feature. When the system is next
disarmed any zones set to Omit will be cancelled.
ZONE LOCKOUT
If a detector on an active zone is triggered while the
system is armed an alarm condition will occur. After
the programmed alarm duration has expired the alarm
will stop and the system will automatically reset.
Subsequent detectors triggered will again initiate an
alarm condition. If a single zone initiates an alarm
condition more than three times then that zone will be
‘Locked Out’ and any further alarm signals from that
zone will be ignored until the system is disarmed.
Note: The ‘Zone Lockout’ feature can be disabled if
required.
EVENT LOG
The Control Panel incorporates a memory capable of
storing the last 50 system events. This enables the
user to see which user has Armed/Disarmed the
system and if and when any alarms occurred. The
time, date and details of the event type will be recorded
for each system event.
CHIME
Chime is a low security facility for use when the system
is Standby mode. If the Chime feature is ON, and a
detector on a zone that has its Chime function enabled
is triggered, the internal sounder will produce a low
volume warning tone. A typical use of the Chime
function would be to warn that a door or particular area
has been accessed.
As an alternative to the Voice dialer the system may be
configured to interface with a central monitoring station.
LATCH KEY
When the system is disarmed the Latch-Key facility, if
enabled, will call the first latchkey phone number and
replay the user message (recorded under user setup)
for the set ‘Play Time’.
The recipient must
acknowledge the message by pressing the
button on the telephone keypad.
If the call is
unanswered or an acknowledgment is not received
then the second latchkey phone number will be called.
The voice dialer will continue calling each number in
turn until each number has been dialed the set number
of times or the sequence is cancelled/acknowledged by
the recipient.
For example, the latchkey facility is useful to inform
parents that a child has returned from school and
disarmed the system.
ANSWER PHONE
The Control Panel includes an answer-phone facility.
The answer phone will record and store a maximum of
6 messages with each message being limited to a 30s
duration.
Messages may be retrieved either direct from the
Control Panel or by dialing into the system from a
phone.
VOICE MEMO
In addition it is also possible to record messages at the
Control Panel using the ‘Voice-Memo’ facility. Each
voice-memo message is limited to a maximum duration
of 30s and counts as an answer phone message.
VOICE DIALER
If the Voice Dialer is enabled and an alarm condition
occurs, the system will call for help using your recorded
alarm messages and up to four telephone numbers.
When an alarm condition occurs, the telephone voice
dialer (if enabled) will call the first enabled number in
the calling sequence and replay the recorded alarm
REMOTE SYSTEM CONTROL
It is possible to dial into the system via the connected
telephone line to interrogate the system status and to
have basic control over the system, (e.g. to Arm and
Disarm the system). You may also activate the
microphone on the control panel to Listen-In to what is
happening in the protected property.
Answer phone and Voice-memo messages may also
be accessed remotely.
TAMPER PROTECTION
All system devices (except the Remote Control Units)
incorporate Tamper protection features to protect
against unauthorized attempts to interfere with the
device. Any attempt to remove the battery covers from
any device (except the Remote Control) or to remove
the Solar Siren or Control Panel from the wall will
initiate an alarm condition (unless the system is in Test
or Programming modes), even if the system is
Disarmed.
JAMMING DETECTION
In order to detect any attempts to illegally jam the radio
channel used by your alarm system, a special jamming
detection function is incorporated into the Control Panel
and Solar Siren. If this feature is enabled, and the
radio channel is jammed continuously for 30 seconds,
when the system is armed, the Solar Siren will emit a
pre-alarm series of rapid bleeps for 5 seconds. If the
jamming continues for a further 10 seconds or more a
full alarm condition will occur. In addition if the system
is jammed for more than three periods of 10 seconds in
a 5 minute interval, this will also generate a Full Alarm
condition.
Control Panel) to the same ON/OFF combination (the
House Code) selected by the user/installer. The
Control Panel is then programmed to operate only with
devices set to this House Code. All detectors and
Remote Control Unit(s) must be configured with the
same House Code in order for the system to operate
correctly.
Inside the Siren, Detectors and Remote Control Unit is
a series of 8 DIP switches.
ECE
ON
The House Code is set up by moving each of the 8
switches in each device to the same randomly selected
ON/OFF sequence. When setting the DIP switches,
ensure that each switch ‘clicks’ fully into position. Use
the tip of a ballpoint pen or a small screwdriver to move
each switch in turn.
Note: it is recommended that the system House Code
is always reset to a code other than the factory default.
The jamming detection features in the Control Panel
and Solar Siren operate independently.
The Jamming Detection circuit is designed to
permanently scan for jamming signals. However, it is
possible that it may detect other local radio interference
operating legally or illegally on the same frequency. If
it is planned to operate the jamming detection feature
we recommend that the system is monitored for false
jamming alarms for at least 2 weeks prior to leaving the
Jamming Detection function permanently enabled.
BATTERY MONITORING
In addition to the battery monitor and low-battery
indicators in each device, the Control Panel will also
indicate a low battery status within any Passive
Infra-Red or Magnetic Contact Detector on the system
using the Event log.
SYSTEM HOUSE CODE
In order to prevent any unauthorized attempt to operate
or disarm your system, you must configure your system
to accept radio signals only from your own system
devices. This is done by setting a series of eight
miniature (DIP) switches in all devices (except the
PLANNING AND EXTENDING YOUR
WIREFREE ALARM SYSTEM
The following example below shows a typical property
incorporating the suggested positions for the Control
Panel, PIR and Magnetic Detectors for optimum
security. Use this as a guide for your installation in
conjunction with the recommendations contained in this
manual for planning your intruder alarm system.
Before attempting to install your Alarm System it is
important to study your security requirements and plan
your installation.
The alarm system may be extended to provide even
greater protection by fitting additional PIR Detectors
and Magnetic Contact Detectors as required.
REMOTE CONTROL UNIT
The Remote Control Unit is used to Arm, Part-Arm and
Disarm the system.
4. Insert the battery under the clip ensuring that the
+v terminal faces upwards away from the PCB.
5. Replace the rear cover and fixing screw.
The Remote Control Unit also incorporates a Panic
switch. Activating the Panic switch on the side of the
Remote Control will immediately initiate a Full Alarm
condition whether the system is Armed or Disarmed.
The alarm can be cancelled by pressing the ‘DISARM’
button on the Remote Control or via the Control Panel.
CONTROL PANEL
LOCATING THE CONTROL PANEL
Any number of Remote Control Units can be used with
your system, providing they are all coded with the
same system House Code.
The Remote Control adopts a CR2032 type Lithium cell
which under normal conditions will have typical life in
excess of 1 year. Under normal battery conditions the
LED on the Remote control will only illuminate when a
button is pressed.
However, under low-battery
conditions this LED will flash every time the button is
pressed. When this occurs the batteries should be
replaced as soon as possible.
SETTING THE REMOTE CONTROL
1. Remove the rear cover by undoing the small screw
on the rear of the Remote Control.
2. Located above the battery cover is a row of 8 DIP
switches. Select and record a random combination
of ‘ON’ and ‘OFF’ positions for the DIP switches.
This will be the system House Code that enables
all elements of your transmitters to communicate
with the Control Panel.
IMPORTANT: The House Code for your system
should be changed from the factory default setting.
3.
Ensure that the jumper link located immediately
below the House Code DIP switches is fitted in
position for use with this alarm system.
When choosing a suitable location for the Control
Panel, the following points should be considered.
1. The Control Panel should be located in a position
out of sight of potential intruders and in a safe
location, but easily accessible for system
operation.
2. The Control Panel should be mounted on a sound
flat surface to ensure that the rear tamper switch
on the Control Panel is closed when the Panel is
mounted. The Control Panel should be mounted
at a convenient height of between 1.5 and 2m and
in a position where it will be seen each day.
Note: If small children are in the household, a
further consideration should be given to keeping
the units out of their reach.
3. It is recommended that the Control Panel should
be positioned such that the Exit/Entry tone (emitted
by the Control Panel) can be heard from outside
the property.
4. The Control Panel should be mounted within a
protected area so that any intruder cannot reach
the Control Panel without opening a protected door
or passing through an area protected by a PIR
detector when the system is armed.
5. The Control Panel must be located within reach of
a mains socket.
6. If the telephone based functionality is to be used
then the Control Panel will need connecting to a
convenient telephone point.
LCD Display Window
5. Route the cable from the Power Supply Unit up
behind and on the right hand side of the Control
Panel and connect the plug to the DC power
socket in the panel. Ensuring that the cable is not
trapped between the panel and the wall.
6. Fix the Panel to the wall using two 18mm No. 4
screws in the lower two fixing holes in the panel
and tighten the upper fixing screws until they just
grip the casing. Do not over tighten the fixing
screws as this could damage or distort the casing.
7.
Ensure that the ‘Reset’ and the ‘Hard-Wired
Siren tamper detect’ jumper links are set in the
OFF position.
8. Connect battery leads to both back-up batteries
and refit batteries.
Keypad
Status LEDs
LCD Control Panel – Keypad and LED Layout
Note: It is recommended that the telephone
connection lead is not extended beyond 5m before
connecting to a telephone master or secondary
outlet.
7. Do not locate the Control Unit closer than 1m to
any large metallic object, (e.g. mirrors, radiators,
etc) as this may affect the radio range of the
Control Panel.
MOUNTING THE CONTROL PANEL
Battery 1 (left): Red lead to +ve battery terminal
Blue lead to –ve battery terminal
Battery 2 (right): Blue lead to +ve battery terminal
Black lead to –ve battery terminal
IMPORTANT: Take care when connecting battery
leads to the batteries as connecting incorrectly
could damage the batteries or the Control Panel.
Note: The Power LED may flash to indicate that
the unit is being operated from the back-up
batteries and that mains supply is not present.
9. If fitted, remove the plastic film covering the LCD
display and on the display window on the cover.
1. Undo the two captive fixing screws on top of the
panel and open the cover. The cover is hinged
along the bottom edge.
10. Close the lid of the Control Panel and tighten the
captive fixing screws.
2. Unclip and remove the two back-up batteries on
either side of the panel.
11. Plug in and switch ON the Power Supply Unit, (the
Power LED should illuminate).
3. Hold the Control Panel in position on the wall and
mark the positions of the four fixing holes.
Remove the Panel and drill four 5mm holes and fit
the 25mm Wall Plugs.
12. If required, connect the Control Panel to the
telephone line using the cable supplied by inserting
small RJ11 plug into socket marked LINE located
on the bottom edge of the Control Panel.
IMPORTANT: Do not drill the fixing holes with the
Control Panel in position; as the resulting dust and
vibration may damage the Control Panel’s internal
components and invalidate the guarantee.
If the cable supplied is not long enough to reach a
suitable phone point then it will need extending
using a coupler and extension lead (not supplied).
4. Fit two 18mm No.4 screws into the top holes until
almost fully home and hang the Control Panel over
these screws using the two keyhole slots in the top
corners of the panel casing.
Note: If the Panel Tamper alarm sounds during the
installation reset the alarm by pressing:
,,
on the Control Panel Keypad.
Terminal Block
External Tamper
Switch Jumper
Link P51
Upper Keyhole
Fixing Hole
Upper Keyhold
Fixing Hole
-ve Terminal
(Black Lead)
+ve Terminal
(Red Lead)
+ve Terminal
(Blue Lead)
-ve Terminal
(Blue Lead)
Reset Jumper
Link P1
Lower Fixing
Hole
Power Supply
Jack Socket
Inside View of Control Panel
SETTING THE CONTROL PANEL HOUSE
CODE
display beneath the corresponding DIP switch
numbers (1-8).
With unit in Standby mode (power LED only
illuminated).
4. Press
Standby mode.
1. Press
TESTING THE CONTROL PANEL &
REMOTE CONTROL
to put the system into Programming mode.
‘1. USER SETUP’ will be displayed.
2. Use the
and
buttons to scroll
through the menu until ‘2. SYSTEM SETUP’
is displayed.
Press
displayed.
and ‘2-1 Learn House Code’ will be
Press
again to set the Control Panel to
receive the House code. ‘DIP SW 12345678 & H
Code: xxxxxxxx’ will be displayed.
3. With the required House Code already configured
on the Remote Control, press the
button on
the Remote Control.
When the Control Panel receives the signal from
the Remote Control the Display will change to
show the received house code on lower line of the
to return to
1. Press
to put the system into Test mode.
‘TEST MODE – WALK TEST’ will be displayed.
2. Press
to activate Walk Test.
‘ Walk Test Waiting…’ will be displayed.
3. Press the ‘ARM’ button on the Remote Control.
As the key is pressed the Control Panel will beep
and the type of the device and button will be
shown on the display.
Press the other buttons on the Remote Control in
turn, as each button is pressed the Control Panel
will beep and show the button being pressed on
the display.
4. Test the range of the Remote Control by pressing
the ‘DISARM’ button on the Remote Control from in
and around the property and from all locations
where you plan to install detectors. Check that
the Control Panel acknowledges the signal from
the
Remote Control each time the ‘DISARM’ button is
pressed.
5. Press
to return to the top level menu of
TEST MODE.
PASSIVE INFRARED DETECTORS
PIR detectors are designed to detect movement in a
protected area by detecting changes in infra-red
radiation levels caused, for example, when a person
moves within or across the devices field of vision. If
movement is detected an alarm signal will be emitted,
(if the system and alarm zone is armed).
Note: PIR detectors will also detect animals, so ensure
that pets are not permitted access to areas fitted with
Passive Infra-Red Detectors when the system is
armed.
Any number of PIR Detectors can be used with your
system, providing they are all coded with the system
house code and are mounted within effective radio
range of the Control Panel.
The PIR Detector adopts a PP3 Alkaline battery which
under normal conditions will have typical life in excess
of 2 years. When the battery level drops, with the PIR
in normal mode and the battery cover fitted, the LED
behind the detection window will flash. When this
occurs the batteries should be replaced as soon as
possible.
CHOOSING A MOUNTING LOCATION
The recommended position for a PIR Detector is in the
corner of a room mounted at a height between 2 and
2.5m.
At this height, the detector will have a
maximum range of up to 12m with a field of view of 110
°. The position of the PCB inside the PIR can be set to
5 different positions to adjust the range of the detector.
Setting the PCB in position 3 will reduce the range to
9m approximately, with position 1 providing a range of
6m approximately.
The recommended position
setting for the PCB is in position 5.
12
PCB Position
Range
6m
9m
12m
Note: The range as indicated above refers to the
linear distance in front of the PIR sensor.
When considering and deciding upon the mounting
position for the detector the following points should be
considered to ensure trouble free operation:
1. Do not locate the detector facing a window or
where it is exposed to or facing direct sunlight.
PIR Detectors are not suitable for use in
conservatories.
2. Do not locate the detector where it is exposed to
ventilators.
3. Do not locate the detector directly above a heat
source, (e.g. fire, radiator, boiler, etc).
4. Where possible, mount the detector in the corner
of the room so that the logical path of an intruder
would cut across the fan detection pattern. PIR
detectors respond more effectively to movement
across the device than to movement directly
towards it.
Less Sensitive
More Sensitive
5. Do not locate the detector in a position where it is
subject to excessive vibration.
10
110°
TOP VIEW
6. Ensure that the position selected for the PIR
detector is within effective range of the Control
Panel, (refer to ‘Testing the Control Panel &
Remote Control’).
10
12
12 10 8
UNIT:M
SIDE VIEW
Note: When the system is armed, household pets
should not be allowed into an area protected by a
PIR detector as their movement would trigger the
PIR and generate an alarm.
Note: DO NOT fix the detector to metalwork or
locate the unit within 1m of metalwork (i.e.
radiators, water pipes, etc) as this could affect the
radio range of the device.
INSTALLING THE PIR DETECTORS
7. To refit the PIR detector to the rear cover, offer the
detector up to the rear cover and locate the clips in
the top edge into the rear cover. Push the lower
edge of the detector into place and refit the fixing
screw in the bottom edge of the PIR to secure in
position. Do not over-tighten the fixing screws as
this may damage the casing.
SETTING THE PIR DETECTORS
Located on the PCB of the PIR Detector are two blocks
of DIP switches (SW2 and SW3).
Ensure that the system is in Test Mode.
1. Undo and remove the fixing screw from the bottom
edge of the PIR. Carefully pull the bottom edge of
the detector away from the rear cover and then
slide down to release the top clips.
Dip Switches
PCB Position
Indicator
Rear Cover
Mounting Hole
Positions
PCB Board
Fixing
Screw
2. Carefully drill out the required mounting holes in
the rear cover using a 3mm drill according to
whether the unit is being mounted in a corner or
against a flat wall.
3. Using the rear cover as a template, mark the
positions of the fixing holes on the wall.
4. Fix the rear cover to the wall using the two 18mm
No.4 screws and 25mm wall plugs, (a 5mm hole
will be required for the wall plugs). Do not
over-tighten the fixing screws as this may distort or
damage the cover.
5. Configure the PIR detector as described below.
Remember that on initial installation that the device
needs to be tested and should therefore be set in
Walk Test Mode.
6. Check that the detector PCB is located and set in
the correct position to give the detection zone
pattern required.
To adjust the PCB position, simply slide it up or
down ensuring that the location legs are aligned
with the required position number marked on the
board.
10
1. DIP switches SW2 (numbered 1-8) are used to set
the House Code for the PIR Detector and must be
set to the same ON/OFF combination as the House
Code DIP switches in all other system devices.
2. Set the alarm zone which the detector will operate
on with DIP switches 1-3 of SW3 as follows:
DIP 1
DIP 2
DIP 3
Zone 1
OFF
OFF
OFF
Zone 2
OFF
OFF
ON
Zone 3
OFF
ON
OFF
Zone 4
OFF
ON
ON
Zone 5
ON
OFF
OFF
Zone 6
ON
OFF
ON
3. DIP 4 of SW3 is used to configure the PIR Detector
for walk test mode, which allows the operation of
the detector to be checked during installation
without triggering a Full Alarm.
ON
OFF
Walk Test mode
Normal mode
Note: On initial installation the detector should be
set into Walk-Test mode ready for testing.
4. The PIR Detector incorporates an anti-false alarm
feature designed to compensate for situations
where the detector may be affected by
environmental changes, (e.g. insects, air
temperature, etc).
This feature is called
“sensitivity detection” and may be selected for high
or low detection.
1. Use the
and
buttons to scroll
through the menu until ‘WALK TEST’ is displayed.
The recommended setting is for high sensitivity
detection.
However, in cases of extreme
environmental problems or if unattributable false
alarms are experienced, it may be necessary to
select low sensitivity detection.
2. Walk into and move slowly around the protected
area, each time the detector senses movement the
LED behind the lens will flash. In addition, the
Control Panel will beep to indicate that the alarm
signal has been received and the identity of the zone
that the detector is configured for will be displayed.
Set the required sensitivity detection using DIP 5 of
SW3 as follows:
ON
OFF
high sensitivity detection
low sensitivity detection
Note: The higher the sensitivity detection the less
movement will be necessary before the PIR
detector will trigger the alarm.
5. The setting of the DIP4 & DIP5 of SW3 can be
distinguished from the LED indication as follows:
Position
DIP4 of
DIP5 of
Trigger reaction of LED
of DIP4
SW3
SW3
Walk Test
High
LED will be on shortly.
mode
Sensitivity
It implies high
& 5 of
SW3
ON
sensitivity.
Low
LED will flash three
Sensitivity
times and Illuminate
once. It implies low
Press
to activate Walk Test.
‘ Walk Test Waiting…’ will be displayed.
If necessary adjust the detection range by changing
the mounting position of the PCB within the PIR
housing.
Note: In normal operation, the LED behind the PIR
lens will not flash on movement detection, (unless
the battery is low).
If necessary re-adjust the detection pattern by
changing the mounting position of the PCB within
the PIR housing.
3. Remove the back cover of the PIR detector. The
Control Panel should beep and display ‘Accessory
Tamper’ to show that the detector’s tamper switch
has been activated.
4. Press
to return to the top level menu of
TEST MODE.
5. Reconfigure the PIR Detector for normal mode by
setting DIP4 of SW3 to OFF and refit in position.
sensitivity.
OFF
Normal
Low
mode
Sensitivity
LED does not light up
6. Connect the PP3 Alkaline battery to the battery
clip.
Note: When the 9V Alkaline battery is connected,
the LED behind the lens will flash for 2-3 minutes
until the PIR has warmed-up and stabilized. The
LED will then stop flashing and turn OFF.
TESTING THE PIR DETECTORS
Ensure that the system is in Test Mode.
With the PIR detector set in Test mode and mounted in
position on the wall, allow 2-3 minutes for the detector
to stabilize before commencing the Walk Test.
Note: When the detector is fully installed i.e. battery
cover is refitted; the unit will not detect movement for
approximately 45 seconds after each activation. (This
feature is present to conserve battery power and
maximize the battery life).
MAGNETIC CONTACT
DETECTOR(S)
The Magnetic Contact consists of two parts; a Detector
and a Magnet. They are designed to be fitted to
either doors or windows with the Magnet mounted on
the moving/opening part and the Detector mounted on
the fixed door or window frame.
The Magnetic Contact Detector is powered by two
CR2032 type Lithium cells which under normal
conditions will have typical life in excess of 1 year.
Under normal battery conditions the LED on the
11
Detector will not illuminate when the Detector is
triggered, (unless in test mode). However, under low
battery conditions this LED will be illuminated for
approx. 1 second when the detector is triggered.
When this occurs the batteries should be replaced as
soon as possible.
The Magnetic Contact Detector has the facility to
connect an additional wired Magnetic Contact. This
additional contact must be of a normally closed contact
type with the contacts being opened in order to
generate an alarm condition.
Any number of Magnetic Contact Detectors can be
used with the system, providing they are all coded with
the system house code and are mounted within
effective radio range of the Control Panel.
CHOOSING A MOUNTING LOCATION
The Magnetic Contact Detector is suitable for mounting
in dry interior locations only.
Decide which doors/windows are to be protected by
fitting Magnetic Contact Detectors, (usually the front
and back doors as a minimum will have Magnetic
Contact Detectors fitted). Additional detectors may
also be fitted where required to other vulnerable doors
or windows, (e.g. garage, patio/conservatory doors
etc).
Ensure that the position selected for the Magnetic
Contact detector is within effective range of the Control
Panel, (refer to ‘Testing the Control Panel & Remote
Control’).
3. Mount the Detector to the fixed part of the frame
along the opening edge opposite the hinges using
either the double sided adhesive tape or screws
provided.
If fixing the Detector with screws; fit the Keyhole
slot in the top of the Detector over the head of the
smaller pan-head screw. Secure the bottom of
the Detector using the 12mm countersunk head
screw fitted within the battery compartment. You
will need to drill out the centre of the fixing screw
hole using a 3mm drill. Do not over-tighten the
fixing screws as this may distort or damage the
casing.
Note: Take care when fixing the Detector to a metal
frame, or mounting within 1m of metalwork (i.e.
radiators, water pipes, etc) as this could affect the radio
range of the device. If required, it may be necessary
to space the magnet and detector away from the metal
surface using a plastic or wooden spacer to achieve
the necessary radio range.
INSTALLING THE MAGNETIC CONTACT
DETECTORS
Ensure that the system is in Test Mode.
1. Remove the battery cover by sliding and lifting it off.
(DO NOT use a screwdriver to lever the cover off)
2. Remove the battery holder by carefully tilting up
the end and pulling the connector off of the printed
circuit board.
12
4. Fit the Magnet to the moving part of the
door/window opposite the Detector using the
adhesive tape or 15mm fixing screws. Ensure that
the parallel gap between the Magnet and Detector
is less than 10mm and that the arrow on the
Magnet is pointing towards and aligned with the
mark on the Detector.
5. If an additional wired Magnetic Contact is required,
this should be wired to the terminal block provided
in the battery compartment. The wired contact
should be connected using two core (24AWG) wire
of maximum length 1.5m.
conform to any of the above mentioned six criteria,
the Control Panel cannot receive triggering signal
from the magnetic contact detector.
4. If additional external contacts are wired to the
Detector, remove the jumper link S2 on the PCB.
A cable entry cut-out is provided beside the
terminal block in the battery cover.
6. Slide the batteries supplied into the battery holder,
ensuring that the positive (+) side is uppermost on
each battery as it is installed.
7. Carefully refit the battery holder onto the Detector
ensuring that the spring connectors slide onto
either side of the circuit board.
IMPORTANT: If external contacts are not
connected, then jumper link S2 must be fitted for
the detector to operate correctly.
TESTING THE MAGNETIC CONTACT
DETECTORS
Ensure that the system is in Test Mode
1.
8. Refit the battery cover.
Use the
and
buttons to scroll
through the menu until ‘WALK TEST’ is displayed.
SETTING THE MAGNETIC CONTACT
DETECTORS
Press
to activate Walk Test.
‘Walk Test Waiting…’ will be displayed.
1. Located in the battery compartment is a row of 11
DIP switches.
2.
As the battery cover is removed the LED on the
Detector will illuminate for approx. 1 second to
indicate that the tamper switch has been activated.
In addition, the Control Panel will beep to indicate
that an alarm signal has been received and
‘Accessory Tamper’ will be displayed.
2. DIP switches 1-8 are used to set the House Code
for the Magnetic Contact Detector and must be set
to the same ON/OFF combination as the House
Code DIP switches in all other system devices.
3.
ON
ECE
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Note: If
DIP 9
DIP 10
DIP 11
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
ON
ON
OFF
OFF
ON
OFF
ON
the setting of DIP switches 9-11 does not
Open the door/window to detach the magnet from
the Detector. As the magnet is parted from the
detector the LED will illuminate for approx. 1
second to indicate that the Detector has been
triggered. In addition, the Control panel will beep
to indicate that an alarm signal has been received
and the identity of the zone that the detector is set
for will be displayed.
Note: In normal mode with the battery cover fitted,
the LED on the detector will not illuminate when
the detector is triggered, (unless the battery is
low).
10 11
3. Configure the alarm zone which the detector will
operate on with DIP switches 9-11 as follows:
Remove the battery cover by sliding off.
4.
If connected, operate the wired Magnetic Contact.
As the contact is opened the LED on the Detector
should illuminate for 1 second to indicate that it has
been triggered and the Control Panel will
acknowledge the alarm signal.
5.
Refit the battery cover on the Detector.
6.
Press
to return to the top level menu of
TEST MODE.
13
EXTERNAL CONNECTIONS
Control Panel cover and tighten the fixing screws on
the top edge of the Control Panel.
The Control Unit incorporates a terminal block for
connection of hard-wired Zones (7-10), Siren or
Telephone Dialer unit. The connection terminal block
is located inside the Control Panel behind the front
cover.
To access the terminal block
Press
this puts the system into Test Mode and prevents an
alarm occurring. Undo the two fixing screws on the
top edge of the Control Panel and open the front cover.
Before making any connections, ensure that the
memory jumper link P1 is in the ‘OFF’ position and then
remove the DC power jack and disconnect one of the
back-up batteries.
Switched
12Vdc output for
external Siren
(300mA max.)
Permanent
12Vdc power
supply output
(100mA max.)
GND
OUT
V+
GND
N.O.
Latching
relay contacts
(Volt-free)
N.C.
Hardwired Zone
Connections
T4
(Using
Normally-Closed
contacts)
T3
T1(Zone 7)
T2(Zone 8)
T3(Zone 9)
T4(Zone 10)
GND
T2
T1
Battery power
pack 12Vdc
input
GND
Tamper circuit
connections for
external devices
GND
B+
TAMP
Terminal Block Detail
Hardwired zone and tamper switches should be Volt
free and Normally Closed, with the contacts opening in
order to initiate an alarm.
Note: Jumper link P51 should be fitted into the ON
position only if the external hardwired tamper circuit is
used, otherwise it must be in the OFF position.
After making your external connections reconnect the
power supply and Back-up Battery. Then close the
14
TESTING THE SYSTEM
door/window protected by a Magnetic Contact
detector. As each detector is triggered the Control
INITIAL TESTING
Panel will chime to indicate that an alarm signal has
As the system is initially installed it is recommended
been received and the identity of the zone that the
that each device is tested in turn as it is installed, (refer
detector is configured for will be displayed.
to testing instructions for particular device).
2. Operate detector anti-tamper switches by opening
TESTING AN INSTALLED SYSTEM
the case of the device.
The Control Panel has a programmed test routine.
operated the Control Panel will chime and
You may test the system at any time, however it is
‘Accessory Tamper’ will be displayed.
As the switches are
recommended that the system is tested at regular
3. Activate each button on the Remote Control in turn.
intervals not exceeding 3 months.
As each button is pressed the Control Panel will
chime and the button name will be displayed. (e.g.
With the system in Standby Mode
‘REMOTE CONTROL DISARM’).
Press
,,
Press
User Password
to exit Walk Test and return to the top
This puts the system into Test Mode.
level Test Mode menu.
The Arm and Part-Arm LEDs will flash.
ALARM TEST
The system is now in the Test Mode. If the battery
Scroll through the top level Test Mode menu until
siren (HA301) is connected, the Control Panel will emit
‘ALARM TEST’ is displayed and press
disarm signal for 1.2 seconds. This offers the battery
siren to learn house code from the Control Panel.
Scroll though the menu until the required alarm
displayed and press
Use the
and
buttons to scroll through
the menu and press
to select the displayed
test function or sub-menu.
to operate the selected
alarm for 5s.
Select ‘Wirefree Siren Test’ to operate the External
Solar Siren.
Note: After completing all required test functions, press
to leave Test mode and return to Standby.
Select ‘Hardwired Siren Test’ to operate the Control
Panel
WALK TEST
Siren
and
external
hardwired
Siren
(if
connected).
Before commencing testing, please ensure that there is
no
movement
doors/windows
in
any
PIR
protected
by
protected
area, all
Magnetic
Contact
Select ‘Relay Test’ to operate the External hardwired
(N.O./N.C.) relay contacts.
Detectors are closed and that all battery covers and
Press
housings are correctly fitted.
to exit Alarm Test and return to the top
level Test Mode menu.
Scroll through the top level Test Mode menu until
‘WALK TEST’ is displayed and press
‘Walk Test Waiting…’ will be displayed.
WIREFREE SIREN SERVICE ON/OFF
Scroll through the top level Test Mode menu until
‘Wirefree Siren Service ON/OFF’ is displayed and
1. Trigger each detector on the system by either
press
walking into a PIR protected area or by opening a
15
This offers the flexibility of removing or changing
siren’s battery.
System Setup
Wait for 10 seconds until ON/OFF
House Code
10101010
duration has elapsed, then go ahead with fixing the
Alarm Time
ON, 180s
siren as desired.
Wirefree Siren
ON
RF Jamming Detection
OFF
Back Light
10s
VOICE DIALER TEST
Alarm Relay
On Until Disarm
Scroll through the top level Test Mode menu until
Zone Lockout
ON
‘VOICE DIALER TEST’ is displayed and press
Remote Phone Control
ON
Rings to Answer Phone
Call Abort
OFF
Dial method
Tone/DTMF
Dialer Mode
Voice Dialer
Time
12:00:00
Date
01/01/03
In order to test the voice dialer properly, the
prerequisite is to set the telephone number, record the
message
and
enable
the
call
routing
in
the
programming mode.
When testing is in progress, simply press
to
stop testing.
If ‘LINE STATUS’ LED is flashing, it implies bad
telephone line connection or telephone network being
out of order. Check the telephone line and re-test it.
Zone Setup (Z1-10)
Name
No Name
Type
Intruder
Final Exit
OFF
Chime
OFF
Entry Delay Zone 1
ON, 30s
Zone 2-10
DIGITAL DIALER TEST
OFF
Part-Arm 1
OFF
Scroll through the top level Test Mode menu until
Part-Arm 2
OFF
‘DIGITAL DIALER TEST’ is displayed and press
Walk Through
OFF
Voice Dialer Setup
In order to test the digital dialer properly, the
Phone Numbers
Not programmed
prerequisite is to set the telephone number and unit ID
Message Play Time
70s
number in the programming mode.
Alarm Messages
Not programmed
Call Routing
All numbers disabled
Call Confirms
Call Attempts
When testing is in progress, simply press
to
stop testing.
If ‘LINE STATUS’ LED is flashing, it implies two causes
Full Arm Setup
of failure. One is bad telephone line connection or
Exit Delay
ON, 30s
telephone network being out of order. The other cause
Entry Delay Beep
ON
of failure is derived from the central monitoring station.
Exit Delay Beep
ON
Consult with the central monitoring station for help.
DEFAULT SETTINGS
User Setup
Users 1-6:
Not programmed
Master Password
1234
16
Part-Arm 1 Setup
Exit Delay
ON, 30s
Entry Delay Beep
ON
Exit Delay Beep
ON
Part-Arm 2 Setup
Exit Delay
ON, 30s
Reconnect the PSU Adaptor plug to the DC power
Entry Delay Beep
ON
socket in the Control Panel and switch On the
Exit Delay Beep
ON
supply to the PSU Adaptor.
7. As the Control Panel powers-up, ‘EEPROM RESET’
Latchkey Setup
Status
OFF
will be displayed while the factory default conditions
Selected User Setup
OFF (all users)
are restored to memory. Once the memory reset
Phone Numbers
Not programmed
has been completed ‘DISARM READY’ will be
displayed.
The Control Panel will now be
reconfigured with all factory default settings.
Home Control Setup
House Code
Unit 1-8 Setup(Unit Code)
01-08
Alarm Trigger
OFF
8. Reset jumper link P1 into the OFF position.
9. Close the Control Panel cover and refit the fixing
screws.
Answer Phone Setup
Status
OFF
Greeting Message
Not programmed
Digital Dialer Setup
Phone No.
Not programmed
Unit ID No.
Not programmed
Call Attempts
Open/Close by user
OFF
RESET FACTORY DEFAULT
1. Press
User Password
to place the system in Test Mode.
2. Undo the Control Panel cover fixing screws and
open the cover.
3. Switch OFF the mains supply to the plug-in PSU
Adaptor and remove the plug from the DC power
socket in the Control Panel.
4. Remove either back-up battery and disconnect the
battery leads.
5. Set jumper link P1 to the ON position.
6. Reconnect the battery leads and replace the
back-up battery in position.
17
PROGRAMMING INSTRUCTIONS
Use the
and
buttons to scroll through
the programming menu. Press
to select the
With the system in Standby Mode.
displayed programming function or sub-menu.
Press
Note: After programming all required functions press
Master Password
to leave Programming mode and return to
The system is now in the Programming Mode
Standby.
USER SETUP
PROGRAM MODE
Code:
1. USER SETUP
User 2
User 3
User 4
User 5
User 6
1-1 USER 1 SETUP
1-7 MASTER USER
SETUP
:1 Password
1234
:1 Password
xxxx
:2 Record
User Message
:3 Replay
User Message
Enter Password
Code:
Start…
Yes->＊ No->＃
Enter Password
Code:
Scroll through the top level programming menu until ‘1.
Enter the new 4 digit Password and then
USER SETUP’ is displayed and press
Press
to save and exit, or
Press
to exit without saving.
Use the
and
buttons to scroll through
the menu until the required user to be configured is
Record User Message
displayed and press
This enables each User to record a short 4s message
for use with the latchkey facility. e.g. “system disarmed
Note: After configuring all required users press
by User-1”.
to return to the top level programming menu.
Scroll through the menu until ‘:2 Record User
Message’ is displayed.
USERS 1-6
Default setting: not programmed
To record a new message press
Scroll through the menu until the required User to be
Press
configured is displayed and press
duration: 4s) Once completed the recording will
to start the voice recorder, (max.
automatically be played back, or
User Password
Scroll through the menu until ‘:1 Password’ is
displayed.
Press
to exit without changing.
The current setting will also be
displayed.
Note: After recording the message, press
to
stop the recorder and cancel any remaining
To change the setting press
18
message time.
Replay User Message
Scroll through the menu until ‘:3 Replay User
Message’ is displayed.
Press
to replay the user message.
Press
to return to the top level User-Setup
menu.
MASTER USER
Default Password: 1234
Scroll through menu until ‘1-7 MASTER USER
SETUP’ is displayed and press
‘:1 Password’ and the current setting will be
displayed.
To change the setting press
Type in a new 4 digit Password, and then
Press
to save and exit, or
Press
to exit without saving.
Press
to return to the top level User-Setup
menu.
19
SYSTEM SETUP
PROGRAM MODE
Code:
2. SYSTEM SETUP
2-1 Learn House
Code
2-3 Wirefree
Siren: xx
DIP SW: 12345678
H Code: xxxxxxxx
Select
ON->＊
OFF->＃
2-2 ALARM TIME
xx
: xxxx
2-5 Back Light
xxs
2-7 Zone Lockout
xx
10s
20s
30s
60s
2-4 RF Jamming
Detection: xxx
Select
OFF->＃
2-6 Alarm Relay
xx xxxxx xxxxx
2-2-2 Time
Enter 1-60(x10)s
Select
ON->＊
OFF->＃
Enter 1-60(x10)s
2s
30s
60s
180s
300s
ON Until Disarm
2-11 Dial Method
xxxxxxxx
Enter 1-30:
ON->＊
Select
ON->＊
OFF->＃
2-2-1 Status
xx
2-9 Rings to
Answer Phone: xx
Tone/DTMF
Pulse
2-10 Call Abort
xxx
2-8 Remote Phone
Control: xx
2-12 Dialer Mode
xxxxx xxxxxx
Voice Dialer
Digital Dialer
Select
OFF->＃
Select
OFF->＃
ON->＊
ON->＊
2-13 TIME & DATE
SETUP
2-13-1 Date
DD/MM/YY DDD
2-13-2 Time
HH/MM/SS
DD/MM/YY
Scroll through the top level programming menu until ‘2
SYSTEM SETUP’ is displayed and press
HH/MM/SS
2. Scroll through the menu until ‘2-1 Learn House
Code’ is displayed.
Note: After completing the system setup press
To program the Control Panel with the system House
to return to the top level programming menu.
Code press
LEARN SYSTEM HOUSE CODE
Press the Control Panel’s keypad 1-8 by selecting 0 or
There are two methods to learn the House Code. One
1 respectively in turn.
is to have the Control Panel learn the system house
code through the remote control.
The other is to
press the Control Panel’s keypad 1-8 by selecting 0 or
Press
to save and exit, or
Press
to exit without saving.
1 respectively in turn (0 means the dip switch is set in
ON position, 1 is set in OFF position).
Make a note of the system house code now in the
space provided on page 41.
1. Scroll through the menu until ‘2-1 Learn House
Code’ is displayed.
ALARM DURATION
Scroll through the menu until ‘2-2 ALARM TIME’ is
To program the Control Panel with the system House
displayed. The current settings will also be displayed.
Code press
To change the settings press
Press
on the Remote Control
On/Off Status
The new programmed system house code will be
recorded into memory and displayed on the bottom
Default setting: ON
line of the LCD, with the corresponding DIP switch
number shown on the top line.
Scroll through the menu until ‘2-2-1 Status’ is
displayed.
20
Press
to save and exit, or
Press
to exit without saving.
The current settings will also be
displayed.
To change the setting press
Press
to enable the Siren, or
Press
to disable the Siren
To change the setting press
Press
to enable Jamming Detection, or
Press
to disable Jamming Detection.
Alarm Duration
Default setting: 180s
Scroll through the menu until ‘2-2-2 Time’ is
CONTROL PANEL BACK LIGHT
displayed.
This controls the time period that the backlight for the
Control Panel display will stay illuminated for after the
To change the setting press
Enter the required alarm duration in units of 10s.e.g.
last key is pressed.
Default setting: 10s
enter 6 for a 60s alarm duration (max setting 60, i.e.
Scroll through the menu until ‘2-5 Back Light’ is
600s/10mins).
displayed. The current setting will also be displayed.
Press
to save and exit, or
Press
to exit without saving.
Press
to return to top level System Setup menu.
To change the setting press
Scroll through available options, (10, 20, 30 and
60s) until the required setting is displayed.
Note: Following initiation of a Full Alarm condition the
External Siren will continue to sound until either the
Press
to save and exit, or
system is disarmed; or the Control Panel Alarm
Press
to exit without saving.
Duration Time expires; or if activated until the 3 minute
alarm time limit of the external Siren expires; whichever
ALARM RELAY
occurs first.
This setting controls the operation period for the
NO/NC hardwired output relay contacts following an
alarm condition being initiated.
WIREFREE SOLAR SIREN
Default setting: ON
If this is set to ‘ON until Disarm’ then the relay will
Scroll through the menu until ‘2-3 Wirefree Siren’ is
latch and remain On until the system is next disarmed.
displayed. The current setting will also be displayed.
Default setting: ON Until Disarm
To change the setting press
Scroll through the menu until ‘2-6 Alarm Relay’ is
Press
to enable the Solar Siren, or
Press
to disable the Solar Siren.
displayed. The current setting will also be displayed.
To change the setting press
JAMMING DETECTION
This feature controls the Control Panels RF jamming
Scroll through available options, (2s, 30s, 60s,
detection circuitry, which if enabled, will continuously
180s, 300s and ‘ON Until Disarm’) until the
scan for radio jamming signals on the system operating
required setting is displayed and then
frequency.
Default setting: OFF
Press
to save and exit, or
Press
to exit without saving.
Scroll through the menu until ‘2-4 RF Jamming
Detection’ is displayed. The current setting will also
be displayed.
21
ZONE LOCKOUT
CALL ABORT
This feature, if enabled, prevents a single zone from
This feature, if enabled, will delay the activation of the
triggering an alarm condition more than three times
telephone dialer following an alarm for a period of
before the system is disarmed. However, if disabled,
approx. 30s to allow the system to be disarmed.
there is no limit on the number of times a zone can
trigger an alarm condition.
Default setting: OFF
Default setting: ON
Scroll through the menu until ‘2-10 Call Abort’ is
displayed. The current setting will also be displayed.
Scroll through the menu until ‘2-7 Zone Lockout’ is
displayed. The current setting will also be displayed.
To change the setting press
Press
to enable Zone Lockout, or
Press
to disable Zone Lockout.
To change the setting press
Press
to enable Call Abort, or
Press
to disable Call Abort.
DIAL METHOD
This feature enables the telephone dialer to be
configured for type of exchange it is connected to.
REMOTE SYSTEM CONTROL
This feature, if enabled, allows the system to be
remotely controlled via the telephone.
Default setting: Tone/DTMF
Default setting: ON
Scroll through the menu until ‘2-11 Dial Method’ is
displayed. The current setting will also be displayed.
Scroll through the menu until ‘2-8 Remote Phone
Control’ is displayed. The current setting will also be
To change the setting press
displayed.
Scroll through available options, (Tone/DTMF and
To change the setting press
Pulse), until the required setting is displayed and
then
Press
Press
to enable Remote Phone Control, or
to disable Remote Phone Control.
Press
to save and exit, or
Press
to exit without saving.
RINGS TO ANSWER PHONE
DIAL MODE
This controls the number of times a connected phone
This facility controls whether the internal telephone
will be allowed to ring before the line is picked up for
dialer operates with the voice or digital dialer facility.
either Answer-Phone and/or Remote Phone Access
The digital dialer is designed to be connected to an
use.
external remote Central Monitoring station service.
Default setting: 6
Default setting: Voice Dialer
To change the setting press
Scroll through the menu until ‘2-12 Dialer mode’ is
displayed. The current setting will also be displayed.
Enter the required number of rings (1-30) before the
Control panel will pick up the call
22
Press
to save and exit, or
Press
to exit without saving.
To change the setting press
Scroll through available options, (Voice dialer and
Digital dialer) until the required setting is displayed.
Press
to save and exit, or
Press
to save and exit, or
Press
to exit without saving.
Press
to exit without saving.
TIME & DATE SETUP
TIME
Scroll through the menu until ‘2-13 TIME & DATE
Scroll through the menu until ‘2-13-2 Time’ is
SETUP’ is displayed and press
displayed. The current setting will also be displayed.
To change the setting press
Note: After configuring the Time and Date press
to return to the top level programming menu.
Enter the time in the format ’hh:mm:ss’.
DATE
Scroll through the menu until ‘2-13-1 Date’ is displayed.
Press
to save and exit, or
The current setting will also be displayed.
Press
to exit without saving.
To change the setting press
Enter the date in the format ‘dd/mm/yy’.
ZONE SETUP
PROGRAM MODE
Code:
3. ZONE SETUP:
Enter Zone (1-10)
3-1 Zxx Name
xxxxxxxxxxxxxx
No name
Front door
Back door
Patio door
Dining room
Living room
Lounge
Kitchen
Shed
Garage
Hall
Landing
Upstairs
Downstairs
Bedroom 1
Bedroom 2
Bedroom 3
Bedroom 4
Windows 1
Windows 2
Windows 3
PIR Detector
Magnetic Contact
FIRE/SMOKE
Panic/PA
3-2 Zxx Type
xxxxxxxxxxxxxx
3-4 Zxx Chime
xxxx
Panic/PA
Intruder
24 hour Intruder
Fire
Test
3-6 Zxx
PART-ARM 1: XXX
Select
OFF->＃
Select
OFF->＃
ON->＊
3-3 Zxx Final
Exit Set: xxx
3-8 Zxx Walk
Through: xxx
OFF
Slave
Master
ON->＊
3-5 Zxx ENTRY
DELAY: XXX
XXX
Select
ON->＊
OFF->＃
3-7 Zxx
PART-ARM 2: XXX
Select
OFF->＃
ON->＊
3-5-1 Status
xxx
Select
OFF->＃
3-5-2 Delay Time
Enter (10-250s)
Enter (10-250s)
ON->＊
Scroll through the programming menu until ‘3. ZONE
are identical except the zone number reference will
SETUP’ is displayed and press
change according to the zone being configured.
Enter the zone number to be configured and press
Note: After completing the Zone Setup press
to return to the top level programming menu.
The following configuration options are based upon
configuring zone 1. Options for all other zones (2-10)
23
NAME
Note: Panic, 24-hour Intruder and Fire modes all
Default setting: ‘No name’
operate on a 24 hour basis, (i.e. they are able to initiate
Full Alarm condition at any time irrespective of whether
Scroll through the menu until ‘3-1 Z01 Name’ is
the system is Armed or Disarmed).
displayed. The current setting will also be displayed.
Default setting: ‘Intruder’
To change the setting press
Scroll through the menu until ‘3-2 Z01 Type’ is
Scroll through available options until the required
displayed. The current setting will also be displayed.
setting is displayed.
To change the setting press
Press
to save and exit, or
Press
to exit without saving.
Scroll through available options until the required
setting is displayed.
TYPE
Each alarm zone may be programmed to operate in
Press
to save and exit, or
one of 5 different modes depending on the type of
Press
to exit without saving.
alarm function it is required to perform. The following
FINAL EXIT SET
alarm types are available:
If enabled, triggering of any detector on the zone
Panic
during the exit-delay will cancel any remaining
- used to provide 24 hour monitoring of any emergency
exit-delay and cause the system to arm 5 seconds
being occurred. Activation of any Panic switch will
later.
immediately initiate a Full Alarm condition.
Default setting: OFF
Intruder
- provides standard intruder monitoring with normal
Scroll through the menu until ‘3-3 Z01 Final Exit Set‘ is
displayed. The current setting will also be displayed.
ARM and PART-ARM functions.
To change the setting press
24 Hour Intruder
- used to provide 24 hour monitoring of areas requiring
continuous security protection even while the system
Press
is Disarmed, (e.g. gun lockers).
facility, or
Activation of any
detector on a security zone will immediately initiate a
Press
Full Alarm condition.
facility.
to enable the zone’s Final Exit Set
to disable the zone’s Final Exit Set
Fire
CHIME
use to provide 24 hour monitoring of any
This controls whether the Chime facility is available on
Fire/Smoke
the zone.
detectors
fitted
to
the
system.
Activation of any detector will immediately initiate a
Full Alarm condition.
Default setting: OFF
Test
Scroll through the menu until ‘3-4 Z01 Chime’ is
when the system is armed, any detector on the
displayed. The current setting will also be displayed.
zone will generate an entry in the Event-Log
To change the setting press
without initiating an alarm condition.
24
Press
to enable the zone’s Chime facility, or
Press
to disable the zone’s Chime facility.
ENTRY DELAY
PART-ARM 2
Scroll through the menu until ‘3-5 ENTRY DELAY’ is
This controls whether the zone is active when Part-Arm
displayed. The current settings will also be displayed.
2 is armed.
To change the settings press
Default setting: OFF
Scroll through the menu until ‘3-7 Z01 Part-Arm 2’ is
On/Off Status
Default setting: Zone 1:
ZONES 2-10:
ON
displayed. The current setting will also be displayed.
OFF
To change the setting press
Scroll through the menu until ‘3-5-1 Status’ is
displayed. The current setting will also be displayed.
Press
to enable the Zone in Part-Arm 2, or
To change the settings press
Press
to disable the Zone in Part-Arm 2.
Press
to enable the zone’s entry-delay, or
WALK THROUGH
Default setting: OFF
Press
to disable the zone’s entry-delay.
Scroll through the menu until ‘3-8 Z01 Walk Through’
Delay Period
is displayed.
The current setting will also be
Default setting: 30s
displayed.
Scroll through the menu until ‘3-5-2 Delay Time’ is
To change the setting press
displayed.
Scroll through available options, (Off, Master and
To change the settings press
Enter the required delay period (10 to 250s)
Press
to save and exit, or
Press
to exit without saving.
Slave), until the required setting is displayed.
Press
to save and exit, or
Press
to exit without saving.
VOICE DIALER SETUP
See diagram on next page.
Press
to return to top level Zone Setup.
Scroll through the programming menu until ‘4. VOICE
PART-ARM 1
DIALER SETUP’ is displayed and press
This controls whether the zone is active when Part-Arm
1 is armed.
Note: After completing the Voice Dialer Setup press
to return to the top level programming menu.
Default setting: OFF
TELEPHONE NUMBERS
Scroll through the menu until ‘3-6 Z01 Part-Arm 1’ is
Scroll through the menu until ‘4-1 PHONE NUMBERS’
displayed. The current setting will also be displayed.
is displayed and press
To change the setting press
Scroll through the menu until the required Telephone
number (1-4) is displayed. The current setting of each
Press
to enable the Zone in Part-Arm 1, or
telephone number will also be displayed.
Press
to disable the Zone in Part-Arm 1.
To change the number press
25
ALARM MESSAGE PLAY TIME
Enter the new telephone number (32 digits max.)
This is the total time for which the alarm messages will
Press
to save and exit, or
be played & repeated when a call made by the voice
Press
to exit without saving.
dialer is answered.
Default setting: 70s
Notes:
Press
to insert a 3.6s pause in the dialing
Scroll through the menu until ‘4-2 Message Play Time’
sequence.
is displayed.
The current setting will also be
Press
to move the cursor left.
displayed.
Press
to move the cursor right.
To change the settings press
Press
Scroll through the available options, (50, 70, 90 and
to delete the character under the
110s) until the required setting is displayed.
cursor.
Press and hold
to erase the entire phone
number.
Press
to save and exit, or
Press
to exit without saving.
After programming all required phone numbers press
to return to the top level Voice Dialer menu.
PROGRAM MODE
Code:
4. VOICE DIALER
SETUP
4-1 PHONE
NUMBERS
4-2 Message
Play Time: xxxx
4-3 RECORD
ALARM MESSAGES
4-4 REPLAY ALARM
MESSAGES
4-7 Call
Attempts: x
4-5 CALL ROUTING
XXXX
Enter 1-5:
50s
70s
90s
110s
4-4-1 Main +
Intruder Message
4-1-1 Phone No. 1
xxxxxxxxxxxxxxxxx
4-1-3 Phone No. 3
xxxxxxxxxxxxxxxxx
Enter Phone No:
Enter Phone No:
26
4-4-3 Main +
Panic/PA Message
4-6 Tel Confirm
Times: x
Enter 1-4:
4-4-2 Main +
Fire Message
4-1-2 Phone No. 2
xxxxxxxxxxxxxxxxx
4-1-4 Phone No. 4
xxxxxxxxxxxxxxxxx
4-5-1 Phone No. 1
xxx
4-5-2 Phone No. 2
xxx
4-5-3 Phone No. 3
xxx
Enter Phone No.
Enter Phone No:
Select
YES->＊
NO->＃
Select
YES->＊
NO->＃
Select
YES->＊
NO->＃
4-3-1 Main
Alarm Message
4-3-2 Intruder
Alarm Message
4-3-3Fire
Alarm Message
4-3-4 Panic/PA
Alarm Message
Start
YES->＊
NO->＃
Start
YES->＊
NO->＃
Start
YES->＊
NO->＃
Start
YES->＊
NO->＃
4-5-4 Phone No. 4
xxx
Select
YES->＊
NO->＃
RECORD ALARM MESSAGES
Scroll through the menu until ‘4-3 RECORD VOICE’ is
number is disabled and a ‘O’ indicates the number is
displayed and press
enabled in the routing sequence. e.g. A display =
“000x” indicates a call sequence of phone nos.1,2 and
3, phone number 4 is disabled and not called.
Scroll through the available menu options until the
required message type to be recorded is displayed.
Default setting: all numbers disabled.
a) Main Alarm message, (12 seconds max).
b) Intruder Alarm message, (4 seconds max).
c) Fire Alarm message, (4 seconds max).
Scroll through the menu until ‘4-5 CALL ROUTING’ is
d) Panic Alarm message, (4 seconds max).
displayed. The current settings will also be displayed.
Scroll through the available menu options until the
To record a new message press
required telephone number (1-4) to be configured is
displayed. The current status will also be displayed.
Press
to start the voice recorder.
Once
completed the recording will automatically be
To change the setting press
replayed, or
Press
Press
to exit without changing.
to enable the number in the routing
sequence, or
Note: After recording the message, press
to
stop the recorder and cancel any remaining message
Press
to disable the number in the routing
sequence.
time.
Press
Press
to return to the top level Voice Dialer setup
to return to the top level Voice Dialer
Setup menu.
menu.
TEL CONFIRM TIMES
REPLAY ALARM MESSAGES
This sets the number of acknowledged phone numbers
Scroll through the menu until ‘4-4 REPLAY ALARM
required to stop the voice dialer. For example if set to
MESSAGES’ is displayed and press
“2” then the dialing sequence will continue until an
acknowledgment
Scroll through the available menu options until the
is
received
from
two
different
numbers, (e.g. Phone No. 1 and Phone No. 3).
required message type is displayed.
Default setting: 1
a) Main + Intruder Messages
b) Main + Fire Messages
Scroll through the menu until ‘4-6 Tel Confirm Times’
c) Main + Panic Messages
is displayed.
The current settings will also be
displayed.
To replay the message press
To change the setting press
Press
to return to the top level Voice Dialer setup
menu.
CALL ROUTING
Enter the required number (1-4).
Press
to save and exit, or
Press
to exit without saving.
This feature controls which telephone numbers are
enabled in the dialing sequence and are dialed when
CALL ATTEMPTS
the voice dialer is activated.
This sets the maximum number of times that the dialer
will attempt to contact each enabled telephone number
The current routing sequence is displayed on screen in
in the call routing sequence.
the order of phone numbers 1-4. An ‘X’ indicates the
27
Scroll through the menu until ‘:1-1 Status’ is displayed.
Default setting: 3
The current setting will also be displayed.
Scroll through the menu until ‘4-7 Call Attempts’ is
displayed. The current settings will also be displayed.
To change the setting press
To change the settings press
Press
to enable the Exit delay, or
Press
to disable the Exit delay.
Enter the required number (1-5).
Delay Period
Press
to save and exit, or
Press
to exit without saving.
Default setting: 30s
Scroll through the menu until ‘:1-2 Delay Time’ is
ARM STATUS SETUP
displayed. The current settings will also be displayed.
PROGRAM MODE
Code:
To change the settings press
5. ARM STATUS
SETUP
Enter the required delay period (10 to 250s).
5-1 FULL ARM
SETUP
:1 EXIT DELAY
XX
XXX
:2 Entry Delay
Beep: xxx
:3 Exit Delay
Beep: xxx
Press
to save and exit, or
Press
to exit without saving.
Press
to return to top level Arm Status Setup
menu.
Select
ON->＊
OFF->＃
Select
ON->＊
OFF->＃
ENTRY DELAY BEEP
Status
xx
:1-2 Delay Time
Enter (10-250s)
Select
ON->＊
OFF->＃
Enter (10-250s)
:1-1
This controls the warning beep which operates during
the Entry Delay period when Full Arm is active.
Default setting: ON
Scroll through the programming menu until ‘5. ARM
STATUS SETUP’ is displayed and press
Scroll through the menu until ‘:2 Entry Delay Beep’ is
displayed. The current setting will also be displayed.
Note: After configuring Arm Status press
to
return to the top level programming menu.
FULL ARM SETUP
To change the setting press
Press
to enable the entry-delay beep, or
Press
to disable the entry-delay beep.
Scroll through the menu until ‘5-1 FULL ARM SETUP’
is displayed and press
EXIT DELAY
EXIT DELAY BEEP
Scroll through the menu until ‘:1 EXIT DELAY’ is
This controls the warning beep which operates during
displayed. The current settings will also be displayed.
the Exit Delay period when Full Arm is initiated.
To change the settings press
Default setting: ON
On/Off Status
Scroll through the menu until ‘:3 Exit Delay Beep’ is
Default setting: ON
displayed. The current setting will also be displayed.
28
To change the setting press
Press
to enable the exit-delay beep, or
Press
to disable the exit-delay beep.
PART-ARM 1 SETUP
To change the settings press
Enter the required delay period (10 to 250s).
PROGRAM MODE
Code:
5. ARM STATUS
SETUP
Press
to save and exit, or
Press
to exit without saving.
Press
to return to top level Part-Arm 1 Setup
menu.
5-2 PART-ARM 1
SETUP
ENTRY DELAY BEEP
:1 EXIT DELAY
XXX
XXX
This controls the warning beep which operates during
:2 Entry Delay
Beep: xxx
:3 Exit Delay
Beep: xxx
Select
ON->＊
OFF->＃
Select
ON->＊
OFF->＃
the Entry Delay period when Part-Arm 1 is active.
Default setting: ON
:1-1 Status
xxx
:1-2 Delay Time
Enter (10-250s)
Select
ON->＊
OFF->＃
Enter (10-250s)
Scroll through the menu until ‘:2 Entry Delay Beep’ is
displayed. The current setting will also be displayed.
To change the setting press
Scroll through the programming menu until ‘5-2
PART-ARM 1 SETUP’ is displayed and press
Note: After configuring Part-Arm 1 press
Press
to enable the entry-delay beep, or
Press
to disable the entry-delay beep.
to
return to the top level programming menu.
EXIT DELAY BEEP
This controls the warning beep which operates during
the Exit Delay period when Part-Arm 1 is initiated.
EXIT DELAY
Scroll through the menu until ‘:1 EXIT-DELAY’ is
displayed. The current settings will also be displayed.
Default setting: ON
To change the settings press
Scroll through the menu until ‘:3 Exit Delay Beep’ is
displayed. The current setting will also be displayed.
On/Off Status
To change the setting press
Default setting: ON
Scroll through the menu until ‘:1-1 Status’ is displayed.
Press
to enable the exit-delay beep, or
Press
to disable the exit-delay beep.
The current setting will also be displayed.
To change the settings press
PART-ARM 2 SETUP
Press
to enable the Exit delay, or
See diagram on next page.
Press
to disable the Exit delay.
Scroll through the programming menu until ‘5-3
PART-ARM 2 SETUP’ is displayed and press
Delay Period
Default setting: 30s
Note: After configuring Part-Arm 2 press
to
return to the top level programming menu.
Scroll through the menu until ‘:1-2 Delay Time’ is
displayed. The current settings will also be displayed.
29
Press
PROGRAM MODE
Code
to return to top level Part-Arm 2 Setup
menu.
5. ARM STATUS
SETUP
ENTRY DELAY BEEP
This controls the warning beep which operates during
5-3 PART-ARM 2
SETUP
the Entry Delay period when Part-Arm 2 is active.
:2 Entry Delay
Beep: xxx
1: EXIT DELAY
xxx xxxx
ON->＊
:3 Exit Delay
Beep: xxx
Select
OFF->＃
ON->＊
Select
OFF->＃
Default setting: ON
Scroll through the menu until ‘:2 Entry Delay Beep’ is
displayed. The current setting will also be displayed.
:1-1 Status
xxx
To change the setting press
:1-2 Delay Time
Enter (10-250s)
Enter (10-250s)
Select
OFF->＃
ON->＊
Press
to enable the entry-delay beep, or
Press
to disable the entry-delay beep.
EXIT DELAY
Scroll through the menu until ‘:1 EXIT-DELAY’ is
EXIT DELAY BEEP
displayed. The current settings will also be displayed.
This controls the warning beep which operates during
the Exit Delay period when Part-Arm 2 is initiated.
To change the settings press
Default setting: ON
On/Off Status
Scroll through the menu until ‘:3 Exit Delay Beep’ is
Default setting: ON
displayed. The current setting will also be displayed.
Scroll through the menu until ‘:1-1 Status’ is displayed.
The current setting will also be displayed.
To change the settings press
Press
to enable the Exit delay, or
Press
to disable the Exit delay.
To change the setting press
Press
to enable the exit-delay beep, or
Press
to disable the exit-delay beep.
LATCH KEY SETUP
See diagram on next page.
Delay Period
Scroll through the top level programming menu until ‘6.
Default setting: 30s
LATCH KEY SETUP’ is displayed and press
Scroll through the menu until ‘:1-2’ Delay Time’ is
Note: After completing the Latch Key Setup press
displayed. The current settings will also be displayed.
To change the settings press
to return to the top level programming menu.
STATUS
This sets the users that the Latch Key facility will
Enter the required delay period (10 to 250s).
operate with. If set to ‘Selected-Users’ the Latch Key
Press
to save and exit, or
will only operate with those users enabled in section
Press
to exit without saving.
‘6-2 Selected User Setup’.
Default setting: OFF
30
Scroll through the menu until ‘6-1 Status’ is displayed.
Press
to enable the Latch-Key for the user, or
Press
to disable the Latch-Key for the user.
The current setting will also be displayed.
To change the setting press
After configuring all Users as required press
Scroll
through
the
available
options,
(Off,
to
return to the top level Latch Key Setup menu.
Selected-Users and All-Users), until the required
TELEPHONE NUMBERS
setting is displayed.
Scroll through the menu until ‘6-3 PHONE NUMBERS’
is displayed and press
Press
to save and exit, or
Press
to exit without saving.
Scroll through the menu until the required telephone
number (1-2) is displayed.
Program Mode Code
The current setting will
also be displayed.
To change the number press
6. LATCH KEY
SETUP
Enter the new telephone number (32 digits max).
6-1 Status
xxx
6-2 SELECTED
USER SETUP
6-3 PHONE
NUMBERS
OFF
Selected-Users
All-Users
Phone No. 1
xxxxxxxxxxxxxxxxx
Phone No. 2
xxxxxxxxxxxxxxxxx
Enter Phone No:
Enter Phone No:
Press
to save and exit, or
Press
to exit without saving.
Notes:
Press
User 1 Status
xxx
User 3 Status
xxx
Select
OFF->＃
ON->＊
ON->＊
User 5 Status
xxx
Select
OFF->＃
User 2 Status
xxx
Select
OFF->＃
ON->＊
ON->＊
User 4 Status
xxx
ON->＊
Select
OFF->＃
User 6 Status
xxx
Select
OFF->＃
Select
OFF->＃
ON->＊
to insert a 3.6s pause in the dialing
sequence.
Press
to move the cursor left.
Press
to move the cursor right.
Press
to delete the character under the
cursor.
Press and hold
to erase the entire phone
number.
After programming all required phone numbers press
SELECTED-USERS SETUP
to return to the top level Latch Key Setup
This allows controls over which users the Latch Key
facility operates with when set to ‘Selected-Users’.
menu.
Default setting: OFF
HOME CONTROL SETUP
This
controls
the
Everspring
Home
Automation
Scroll through the menu until ‘6-2 SELECTED USER
Receiver (e.g. BH002, BH003, BH004 & BH006) for a
SETUP’ is displayed and press
maximum of 8 pcs.
Scroll through the menu until the required user number
Scroll through the top level programming menu until ‘7.
(1-6) to be configured is displayed. The current status
HOME CONTROL SETUP’ is displayed and press
will also be displayed.
To change the setting press
Note:
After completing the Home Control Setup
press
to return to the top level programming
menu.
31
HOME AUTOMATION CONTROLLER HOUSE CODE
displayed. The current settings will also be displayed.
Default setting: A
Scroll through the menu until ‘7-1 Set House Code’ is
To change the settings press
PROGRAM MODE
Code:
7. HOME CONTROL
SETUP
Unit 2
7-1 Set House
Code: xx
7-2 UNIT1 SETUP
House Code: xx
:1 Unit Code: xx
Unit 3
Unit 4
Unit 5
Unit 6
Unit 7
Unit 8
7-10 BY ALARM
TRIGGER XXX XXX
: 10-1 Status
xxx
Select
OFF->＃
:10-2 Active Time
Enter
(30-250s)
Enter (10-250s)
ON->＊
Scroll through the available options, (A~P), until
Enter the unit code (1-16) that your home
the required setting is displayed.
automation receiver has.
Press
to save and exit, or
UNIT 3 SETUP
Press
to exit without saving.
Scroll through the menu until ‘7-4 UNIT3 SETUP’ is
displayed and press
UNIT 1 SETUP
Scroll through the menu until ‘7-2 UNIT1 SETUP’ is
Unit code
displayed and press
Default setting: 03
Unit Code
Scroll through the menu until ‘:1 Unit Code’ is
Default setting: 01
displayed and press
Scroll through the menu until ‘:1 Unit Code’ is
Enter the unit code (1-16) that your home
displayed and press
automation receiver has.
Enter the unit code (1-16) that your home automation
Press
to save and exit, or
receiver has.
Press
to exit without saving.
Press
to save and exit, or
Note: Use the same method as mentioned above for
Press
to exit without saving.
setting the unit 4-8 of home automation receiver.
UNIT 2 SETUP
ALARM TRIGGER
Scroll through the menu until ‘7-3 UNIT2 SETUP’ is
Default setting: OFF
displayed and press
Scroll through the menu until ‘7-10 BY ALARM
Unit Code
TRIGGER’ is displayed. The current setting will also be
Default setting: 02
displayed.
Scroll through the menu until ‘:1 Unit Code’ is displayed
To change the setting press
and press
On/Off Status
32
Default setting: OFF
Scroll through the menu until ‘:10-1 Status’ is
ON/OFF STATUS
displayed. The current setting will also be displayed.
Default setting: OFF
To change the setting press
Scroll through the menu until ’8-1 Status’ is displayed.
The current setting will also be displayed.
Press
to enable the home automation
To change the setting press
receiver, or
Press
to disable the home automation
receiver.
Press
to enable the Answer-Phone, or
Press
to disable the Answer-Phone.
Active Time
This controls the illuminating duration of all the lighting
RECORD GREETING
units connected to BH004/006 when the on/off status is
Scroll through the menu until ’8-2 Record Greeting’
set for “ON”. After the elapse of pre-set illuminating
is displayed.
duration (30-250s variable), the lighting units will be off
To record a new greeting message press
automatically.
Press
Default setting: 30 seconds
to start the voice recorder, (max.
duration: 12s). Once completed the recording will
Scroll through the menu until ‘:10-2 Active Time’ is
automatically be played back, or
displayed and press
Press
Enter the required active duration (30 to 250s).
Press
to save and exit, or
Press
to exit without saving.
Press
to exit without changing
Note: After recording the greeting message, press
to stop the recorder and cancel any remaining
message time.
to return to top level programming
REPLAY GREETING
Scroll through the menu until ’8-3 Replay Greeting’ is
mode.
displayed.
ANSWER PHONE SETUP
To replay the recorded greeting message press
PROGRAM MODE
Code:
DIGITAL DIALER SETUP
PROGRAM MODE
Code:
8. ANSWER PHONE
SETUP
8-1 Status
OFF
Select
OFF->＃
ON->＊
8-2 Record
Greeting
8-3 Replay
Greeting
Start…
YES->＊
Playing …
9. DIGITAL
DIALER SETUP
NO->＃
Scroll through the programming menu until ’8.
9-1 Phone No:
xxxxxxxxx
9-3 Call
Attempts:
9-4 Open/Close
By User:
Enter Phone No:
xxxxxxxxx
Enter 1-5:
x-
Select
ON->＊
OFF->＃
ANSWER PHONE SETUP’ is displayed and press
Note: After completing the Answer Phone Setup press
to return to the top level programming menu.
9-2 Unit ID No:
xxxx
Enter Unit ID:
xxxx
33
Scroll through the programming menu until ‘9. DIGITAL
DIALER SETUP’ is displayed and press
Press
and then 2, a ‘C’ will be presented.
Press
and then 3, a ‘D’ will be presented.
Press
and then 4, an ‘E’ will be presented.
Press
and then 5, a ‘F’ will be presented.
Note: After completing the Digital Dialer Setup press
o to return to the top level programming menu.
PHONE NUMBER
Scroll through the menu until ‘9-1 Phone No:’ is
displayed. The current setting will also be display.
When pressing
for
3 seconds, no further
input is made, it will be regarded as void input.
To change the setting press
CALL ATTEMPTS
Enter the phone number (32 digits max. ranging from
This sets the maximum number of times that the dialer
0~9, *, #,
will attempt to contact the central monitoring station.
) that Central Monitoring station has.
If the dialer contacts to the central monitoring station
Press
to save and exit, or
Press
to exit without saving.
once successfully, it will stop dialing.
Default setting: 3
Notes:
Press
to insert a 3.6s pause in the dialing
Scroll through the menu until ‘9-3 Call Attempts’ is
displayed. The current setting will also be displayed.
sequence.
Press
to move the cursor left.
Press
to move the cursor right.
Press
to delete the character under the
To change the setting press
Enter the required number (1-5).
cursor.
Press and hold
to erase the entire phone
Press
to save and exit, or
Press
to exit without saving.
number.
OPEN/CLOSE BY USER
UNIT ID NUMBER
This determines when user makes a selection for
This helps central monitoring station set an ID number
disarming (Open) or arming (Close) the system, an
for the user whose system is connected to their center.
event code 401 is needed to be sent to the central
monitoring station.
When setting to ‘On’, an event
Scroll through the menu until ‘9-2 Unit ID No:’ is
code 401 will be emitted, setting to ‘Off’, an event code
displayed. The current setting will also be displayed.
401 won’t be emitted.
To change the setting press
Default setting: Off
Enter the ID number (4 digits max. ranging from 0-9,
Scroll through the menu until ‘9-4 Open/Close By
B,C,D,E, F)
User’ is displayed. The current setting will also be
displayed.
Press
to save and exit, or
Press
to exit without saving.
Press
Notes:
Press
To change the setting press
and then 1, a ‘B’ will be presented.
to commence sending the event
code.
Press
34
code.
to commence not sending the event
Press
to return to top level Digital Dialer Setup
menu.
35
OPERATING INSTRUCTIONS
User Password
When leaving the premises, the system must be Armed.
However, before doing so, check that all windows are
closed and locked, all protected doors are closed and
By pressing
, the programmed exit delay
PIR Detectors are not obstructed. Ensure that pets
will be overrided to 5 seconds.
are restricted to areas not protected by PIR Detectors.
PART-ARM 1
The system has three arming modes, ARM, Part-Arm 1
The system can be set in PART-Arm 1 mode using
and Part-Arm 2.
either the Remote Control or the Control Panel as
The Part-Arm modes allow for
selected zones to be left in a Disarmed state while the
follows:
reminder of the system is Armed.
Remote Control:
When the system is Armed (in any mode) the Control
Press the ‘PART-ARM’ button,
Panel will display the arming mode and the status of the
Latch Key for a few seconds. If enabled, the system
Control Panel:
Exit-Delay will start and be counted down on the display.
As the Exit-Delay expires the Control Panel will beep,
with the beep rate increasing in steps as the delay
User Password
expires. At the end of the Exit-Delay all active zones
be Armed. By this time the user must have left the
By pressing
property and closed the final exit door.
be overrided to 5 seconds.
, the programmed exit delay will
If while the system is armed a detector on an active
PART-ARM 2
zone is triggered, if enabled, the programmed
The system can be set in Part-Arm 2 mode using either
Entry-delay for that zone will start and be counted down
the Remote Control or the Control Panel as follows:
on the display. As the Entry-Delay expires the Control
Panel will beep, with the beep rate increasing in steps
Remote Control:
as the delay expires.
Press the ‘PART-ARM’ button twice,
If the system has not been
disarmed when the Entry-Delay expires an alarm will
occur.
zone
If however, the Entry-Delay for the triggered
has
been
disabled
an
alarm
will
Control Panel:
occur
immediately.
User Password
At the end of the programmed alarm duration the Siren
By pressing
and Control Panel alarms will stop and the system will
be overrided to 5 seconds.
, the programmed exit delay will
automatically re-Arm.
DISARM
ARM
The system can be Disarmed using either the Remote
The system can be set in ARM mode using either the
Control or the Control Panel as follows:
Remote Control or the Control Panel as follows:
Remote Control:
Press the ‘DISARM’ button,
Remote Control:
Press the ‘ARM’ button,
..
Control Panel:
Control Panel:
Press the Arm button followed by the User
Password and then the Enter button:
36
User Password
If the system is disarmed and the ‘ALARM MEM’ LED is
The alarm will continue either for the alarm duration
flashing with the panel beeping every few seconds, this
when the system will automatically reset or until the
indicates that an alarm condition has occurred. Use
system is disarmed.
the Event Log to find out and make a note of where the
alarm occurred to assist in tracing the cause of the
TAMPER
alarm.
If the battery cover of any device is removed or if the
Siren or Control Panel are removed from the wall then
QUICK SET
a Full Alarm condition will be initiated even if the
To operate the quick set function and fully arm the
system is Disarmed. The alarm condition will continue
system in 5s, overriding the programmed exit delay.
either for the alarm duration when the system will
automatically reset or until the system is Disarmed.
The ‘ALARM MEM’ LED on the Control Panel will flash
Press
User Password
and the panel will beep every few seconds to indicate
an alarm has occurred.
OMIT ZONE
To omit a zone from the next armed session:
Note: The Tamper protection facility on the Siren
operates independently. If the Tamper on the Siren is
activated this will not be indicated at the Control Panel.
Press
User Password
Scroll through the menu until the required zone is
CHIME
displayed. The current setting will also be displayed.
The Chime facility can only be operated with the
system in Standby mode.
To change the setting press
Press
Press
to omit the zone, (i.e. zone omit ON).
Press
to toggle the Chime facility between ON
and OFF.
to re-enable the zone, (i.e. zone omit
OFF).
Note: If the Chime is ON and the system is then armed
the Chime will remain ON after the system is disarmed.
After configuring zones to be omitted as required
Press
to return to Standby mode.
EVENT-LOG
The Event Log will store the last 50 system Arm, disarm,
Note: Omitting a zone will only affect the next armed
alarm and detector Low Battery events.
session. When the system is disarmed the omitted
Log will record the time, date and details for each event.
zones will be re-enabled ready for the next armed
If when the system is disarmed the “ALARM MEM’ LED
session.
is flashing and the panel beeps every 10s, this
The Event
indicates that an alarm has occurred. To cancel the
PANIC ALARM
LED and stop the beeping you must access the event
A full Alarm condition can be immediately initiated
log or press
at any time (whether the system is Armed or Disarmed)
MEM’ LED and the beeping as well.
to eliminate the flashing ‘ALARM
in the event of threat or danger by activating a Panic
switch on either the Remote Control or the Control
To access the Event Log, (with the system in Standby):
Panel.
Press
Remote Control:
The Event-Log will automatically start scrolling through
Slide the Panic switch upwards.
and displaying the event data starting with the most
recent event. The data for each event is shown on
two screens, each screen will be displayed for 5
Control Panel:
Press and hold the
3 seconds.
button for approximately
37
seconds before moving on to the next screen and then
Note: Press
the next event.
at either stage to cancel delete
and move on to the next message.
Use the
and
buttons to manually scroll
through the event log to the required position as
After all messages have been replayed the system will
necessary.
automatically return to Standby Mode.
Press
REMOTE SYSTEM CONTROL
to return to standby.
If the Remote System Control facility is enabled, the
VOICE MEMO
Control Panel will answer the call after the set number
To record a message, (max. duration 30s), at the
of rings and emit three beeps on the phone line to
Control Panel using the Voice Memo facility, proceed as
prompt for a User Password to be entered using the
follows:
telephone keypad.
A valid User Password will be acknowledged with one
Press
Press
to start recording
long beep. An incorrect code will be acknowledged by
two short beeps.
While recording, press
to stop the recorder
and skip the remaining message time.
If the User Password is not entered within 30s or is
entered incorrectly three times then the Control Panel
If there are already 6 messages recorded it will not be
possible to record
will automatically hang-up the line.
a voice-memo message until a
Note: If the internal Answer-Phone is also enabled and
message has been deleted.
there is space for a new message then the call will be
The Voice Memo message may be accessed either at
answered with the Answer-Phone greeting message.
the Control Panel (see Replay Messages) or via the
The User Password should be entered during the
Remote System Control facility.
greeting message, otherwise the answer phone
message recorder will be activated.
REPLAY MESSAGES
If the ‘MESSAGE’ LED is illuminated, this indicates
By pressing the
button on the telephone keypad
that either a new Answer-Phone or Voice-Memo
within 30 seconds, the Control Panel will automatically
message has been recorded and has not been read.
hang-up the line.
The recorded messages may be accessed at the
Use with an External Answer-Phone:
Control Panel as follows:
If the Remote System Control is to be used in
Press
conjunction with an external Answer-Phone then
User Password
1.
The internal Answer-Phone must be disabled.
2.
The number of ‘ring to answer’ for the Control
Messages are replayed in order starting with the
most recent. Press
to skip to the end of the
message.
Panel must be greater than that of the External
Answer-Phone, otherwise the Control Panel will
At the end of each message there will the option of
always pickup the call before the Answer-Phone.
deleting the message just heard.
To access the Remote System Control facility the
To delete the message
Control Panel has a ‘double dial-in’ feature to enable
Press
to delete the message
the Control Panel to pick-up the phone call before the
Press
to re-confirm and actually delete the
external Answer-Phone cuts in.
message
38
procedure is as follows:
The ‘double dial-in’
Press
1. Dial up the system and hang up after two rings.
to end the session and hang up the
Control Panel line.
2. Redial up the system within 20s as maximum (5s
as minimum), the system will pickup the phone
after 1 ring.
CONNECTION TO HOME AUTOMATION
MODULES
Under the disarm mode, the on/off power of a series of
3. Enter the User Password as normal.
home automation receiver modules can be controlled
by the Control Panel as follows:
The following functions may be access via the remote.
The system will acknowledge each signal with a single
long beep.
1. BH002/003: Press
on the Control Panel’s
keypad and then key in the unit code (numbered
1-8) of home automation receiver modules to turn
Press
to initiate ARM.
on the power manually.
Press
to initiate Part-Arm 1.
Press
on the Control Panel’s keypad and
then key in the unit code (numbered 1-8) of home
Press
to initiate Part-Arm 2.
automation receiver modules to turn off the power
manually.
Press
to Disarm the system.
2. BH004/006: Press
Press
to turn the Siren OFF
on the Control Panel’s
keypad and then key in the unit code (numbered
1-8) of home automation receiver modules to turn
Press
to turn the Siren ON.
on and turn off the power manually.
Note: To turn on and turn off the lighting
Press
to Listen-In via the Control Panel
fixture connected to BH004/006, simply using
Microphone.
Press
as a toggle switch.
to stop Listen-In
Note: Prior to adjusting the dimmer brightness, the
prerequisite is to turn on the lighting fixture.
Note: Listen-in will be automatically cancelled after
Press
5 minutes if not cancelled manually.
then key in the unit code (numbered 1-8) of home
on the Control Panel’s keypad and
automation receiver modules to start dimmer cycle.
Press
to interrogate the system status.
The
status tone will be repeated at 2s intervals for 15s.
Press
on the Control Panel’s keypad and
then key in the unit code (numbered 1-8) of home
One beep
ARM
automation receiver modules to select the dimmer
Two beeps
Part-Arm (1 or 2)
brightness you desire.
Three beeps
Alarm triggered
Four beeps
Fire triggered
BATTERY MONITORING
One long beep Disarmed
All system devices continuously monitor their battery
Press
to replay Answer-Phone messages.
condition. The Control Panel also monitors the battery
condition of all PIR and Magnetic detectors.
While replaying a message, press
If the
for 2 seconds
battery level of any device drops below acceptable
to skip to the end of the message and hear the next
levels then its low battery indication will be activated.
message.
In addition if any PIR or Magnetic Contact detector has
a low battery status it will be recorded by the Control
Panel and a message stored in the event log.
Press
to delete all Answer Phone messages.
39
In the event of AC adaptor being disconnected from the
MAINTENANCE
Control Panel, the Control Panel by consuming the DC
Your Alarm System requires very little maintenance.
rechargeable battery can sustain 2 days of normal
However, a few simple tasks will ensure its continued
operation (under standby mode) . However, the battery
reliability and operation.
for that device should be replaced as soon as possible.
CONTROL PANEL
Note: Before removing the battery cover on any device
The rechargeable batteries have a typical life of 3-4
to replace the battery ensure that the system is put into
years and need no maintenance during this period,
Test mode to avoid initiating a Full Alarm condition.
provided they are kept charged. The batteries will be
damaged if they are stored in a discharged state for
The low battery indication for each system component
long periods.
is as follows:
DETECTORS AND REMOTE CONTROL
Control Panel
The Detectors require very little maintenance.
During a period of mains supply interruption the Control
batteries should be replaced once a year or when a low
Panel will be powered by the rechargeable backup
battery status is indicated.
The
batteries. Under normal battery conditions the Power
LED on the panel will flash at 1s intervals. However,
IMPORTANT: Should you, for any reason, have to
under low battery conditions the Power LED will flash at
completely power-down the system (e.g. to move the
3s intervals.
system to a new premises) first put the system into Test
mode before removing the Control Panel cover and
Remote Control
disconnecting the power supply and backup batteries.
When the Remote Control is operated under low
battery conditions the transmit LED will continue to
BATTERIES
flash after the button has been released.
Before removing the battery cover on any device to
replace the battery, ensure that the system is put into
Under normal battery conditions the LED will extinguish
Test mode to avoid initiating an Alarm.
when the button is released.
The specifications for replacement batteries are as
PIR Detectors
follows:
Under low battery conditions the LED behind the
detector lens will flash when movement is detected to
Remote Controls
indicate that the battery needs to be replaced.
1 x 3V CR2032 Lithium Cells
(or equivalent)
Magnetic Contact
2 x 3V CR2032 Lithium Cells
Under normal battery conditions the LED does not
Detectors
(or equivalent)
illuminate unless the PIR detector is in Walk Test mode.
PIR Detectors
1 x 9V PP3 Alkaline
Magnetic Contact Detectors
Note: Where applicable only fit PP3 Alkaline type
Under low battery conditions, when the Detector is
batteries.
activated the transmit LED will be illuminated for
fitted.
Rechargeable batteries should NOT be
approximately 1s as the door/window is opened.
At the end of their useful life the batteries should be
Under normal battery conditions the LED will not
disposed of via a suitable Recycling Centre. Do not
illuminate as the Detector is operated, (unless the
dispose of with your normal household waste.
Detector is in Test Mode with the battery cover
NOT BURN.
DO
removed).
The Rechargeable batteries contain Sulphuric Acid –
40
DO NOT ATTEMPT TO OPEN THE CASING.
ALARM RECORD
Complete the following information during installation for future reference when adding to your system and to assist
Trouble Shooting.
Zone Settings
Zone
Detector
Location
Type(s)
Type
Final
Entry
Exit
Delay
Chime
Arm
Part-Arm
Part-Arm
10
You may make a note of your User Password and Installer Password below.
System Password
User 1: _______________________ User 2: _______________________ User 3: _______________________
User 4: _______________________ User 5: _______________________ User 6: _______________________
Master User: ________________________________________
System House Code
ECE
ON
Use the diagram to record your House Code
Voice Dialer Phone Numbers
Phone No. 1: ______________________________ Phone No. 2: ______________________________
Phone No. 3: ______________________________ Phone No. 4: ______________________________
Latch-Key Phone Numbers
Phone No. 1: ______________________________ Phone No. 2: _______________________________
Digital Dialer Phone Numbers
Phone No. ________________________________ System ID No. _______________________________
This information is confidential and should be kept in a safe location.
41
TROUBLE SHOOTING
Control Unit not working – Power LED OFF or
flashing
1. Mains power failure – check if other electrical
circuits are operable.
2. Check that mains adaptor is plugged in and
socket is switched ON.
3. Check mains fuse in Plug has not blown.
4. Check that DC jack plug from mains adaptor is
connected in Control Panel.
5. Check fuse/MCB in Consumer Unit on the
circuit serving the Control Panel.
Note: Before replacing any fuses or resetting
the MCB, the cause of the failure should be
investigated and rectified.
Control Unit not accepting User Password
1. Pause between key depressions too long. Do
not pause for more than 5 seconds between
pressing keys.
2. Incorrect code entered.
3. Reset to factory defaults and reprogram system.
Control Unit not responding to detectors
1.
2.
3.
Ensure that the ‘House Code’ is correctly set.
Ensure detector is within effective radio range
of Control Panel and equipment is not mounted
close to metal objects.
Detector battery low – replace battery.
Voice-Dialer not responding to Alarm
1. Telephone line not connected or faulty – check
phone line with another phone
2. Dial Method incorrectly programmed
3. Incorrect phone numbers programmed
4. Phone numbers disabled in dialing sequence
5. Alarm messages not recorded
42
Answer-Phone not responding or recording
messages
1. Telephone line not connected or faulty – check
phone line with another phone
2. Dial Method incorrectly programmed
3. Answer-Phone disabled
4. No space in message store, 6 messages
already recorded.
Cannot record Voice-Memo message at Control
Panel
1. No space in message store, 6 messages
already recorded.
Control Unit not contacting central monitoring
station service on alarm
1. Telephone line not connected or faulty – check
phone line with another phone.
2. Dial Method incorrectly programmed.
3. Incorrect phone number for central monitoring
station service programmed
4. Incorrect system ID number for central
monitoring station service programmed.
5. Central monitoring station service not
commissioned or signed up.
Control Unit not responding to Remote Phone
Access
1. Telephone line not connected or faulty – check
phone line with another phone
2. Remote Access disabled
3. Incorrect User Password entered
Latch Key not responding when system
disarmed
1. Telephone line not connected or faulty – check
phone line with another phone
2. Dial Method incorrectly programmed
3. Latch-Key disabled
4. Latch Key set to Selected-Users and not
enabled for User that is Disarming the system
5. No Latch-Key phone numbers programmed
Full alarm condition occurs when system has
not been triggered by an intruder or is disarmed
1. Tamper switch activation
- check all detector battery covers to ensure
correctly fitted
- check Control Panel and Siren are securely
mounted to the wall and tamper switch is
closed
2. Panic alarm operated from a Remote Control or
Keypad
3. Jamming detection circuit operated
LED on remote control not illuminating, or is
dim when unit is operated
1. Ensure battery is connected with correct polarity
2. Ensure battery connections are good
3. Replace battery
PIR Detector false alarming
1. Ensure that the detector is not pointing at a
source of heat or a moving object
2. Ensure that the detector is not mounted above a
radiator or heater
3. Ensure that the detector is not facing a window
or in direct sunlight
4. Ensure that the detector is not in a draughty
area
5. Sensitivity detection set too high –reset to low
sensitivity detection
PIR Detector not detecting a person’s movement
1. Check battery connections are good.
2. Sensitivity detection set too low– reset to high
sensitivity detection.
3. Check that the detector is correctly set up.
4. Ensure DIP switches 1-4 of SW3 are correctly
set.
5. Ensure that detector is mounted the correct way
up.
(i.e. with detection window at the bottom)
6. Ensure that the detector is mounted at the
correct height, (i.e. 2-2.5m).
7. Allow up to three minutes for detector to
stabilize.
PIR Detector LED flashes on detection of
movement, (device in normal operation mode)
1. Low battery – replace battery.
Magnetic Contact Detector not working
1. Ensure batteries are connected with correct
polarity.
2. Ensure battery connections are good.
3. Ensure ‘House Code’ is correctly set.
4. Ensure DIP switches 9, 10 and 11 are set
correctly.
5. If no external contacts are connected ensure
jumper link fitted.
6. If external contacts are connected
a. Ensure jumper link removed
b. Check that all contacts are closed.
c. Check all contacts are wired in series.
Magnetic Contact Detector false alarming
1. Ensure that gap between magnet and detector
is less than 10mm.
2. Tamper switch below battery cover not
depressed – check battery cover is fitted
correctly and that fixing lugs are not broken.
LED on Magnetic Contact Detector illuminating
when door or window is opened.
1. Low battery – replace batteries.
DIGITAL DIALER TRANSMISSION
PROTOCOL
Contact ID Event Codes
Definition
Code
Fire/Smoke Alarm
110
Panic Alarm
120
Intruder Alarm
130
24hr Intruder
133
System Tamper
137
AC Failure
301
System Low Battery
302
Sensor Tamper
383
Sensor Low Battery
384
Cancel/Abort Alarm
406
System Test
601
Open/Close by User
401
INH302WEVSP0E2A
43
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2004:03:18 14:30:29+08:00
Modify Date                     : 2004:03:18 14:30:29+08:00
Page Count                      : 46
Creation Date                   : 2004:03:18 06:30:29Z
Mod Date                        : 2004:03:18 06:30:29Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : gracelin
Metadata Date                   : 2004:03:18 06:30:29Z
Creator                         : gracelin
Title                           : Microsoft Word - H302W

EXIF Metadata provided by EXIF.tools