Ewig Macao Commercial Offshore 001H22 Remote Thermo-Hygro Sensor User Manual 683F33

Ewig Industries Macao Commercial Offshore Limited Remote Thermo-Hygro Sensor 683F33

users manual

Download: Ewig Macao Commercial Offshore 001H22 Remote Thermo-Hygro Sensor User Manual 683F33
Mirror Download [FCC.gov]Ewig Macao Commercial Offshore 001H22 Remote Thermo-Hygro Sensor User Manual 683F33
Document ID374831
Application ID9z+RMvq/854J0ZnwYkfqGg==
Document Descriptionusers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize32.09kB (401072 bits)
Date Submitted2003-11-19 00:00:00
Date Available2003-11-19 00:00:00
Creation Date0000-00-00 00:00:00
Producing SoftwareAcrobat Distiller 3.0 for Windows
Document Lastmod0000-00-00 00:00:00
Document Title683F33
Document CreatorAdobe PageMaker 6.5
Document Author: eunice

RF 433Mhz Wireless Remote Sensor 001H22
(HANG)
(STAND)
°C °F
TX
: +32°F to +122°F (0°C to +50°C)
: -58°F to +158°F (-50°C to +70°C)
: Maximum 30 meters, open area
: AAA size x 2 pcs. (remote sensor)
: 6 months
: 433.92 MHz
This device could be sensitive to electrostatic discharge, If electrostatic discharge or malfunctioning occurs, please reset this
unit.
RF REMOTE SENSOR
Specification
Recommended remote sensor operating range:
Sensor with LCD display
Detachable outdoor probe
Transmission range
Batteries
Battery life
Transmission frequency
SLIDE
“Modifications not authorized by the manufacturer may void users authority to operate this device”
SLIDE
A . LCD
Displays temperature and humidity in toggle
B. LED indicator
Flashes when the remote unit transmits a reading
C. °C/°F slide switch
Selection Centigrade (°C) or Fahrenheit (°F)
D. T X
Press once to re-transmit manually. Press and hold to clear the TX ID and start re-registration
E. Battery compartment
Accommodates two AAA-size batteries
F. Battery door
G. Removable table stand with wall-mount hole
To enable the remote unit on a flat surface and support it in wall-mounting.
During the 3 minutes when the home receiver is seeking for sensor registration signal, remove the bracket stand, and
battery cover. Insert 2 pieces of AAA batteries into the battery compartment according to polarity markings. The channel
1 icon and the temperature/humidity will appear on the LCD of the receiving unit.
-If the registration is sucessful, a beep confirmation will be heard. If not, check the AAA batteries, repeat the registration
procedure again, or hold the TX button for 2 seconds to send the registration signal. Then, close the battery door.
-To register sensor 2 and sensor 3: Press and hold the “Channel” button for 2 seconds on the home receiver to select the
channel. Insert batteries for sensor 2, the channel 2 icon and temperature will appear on the LCD of the receiving unit.
Follow the same procedure to register sensor 3.
Note:
•
The sensor will transmit the registration code automatically once the batteries are inserted. If the batteries have
been already inserted into the battery compartment , hold the TX 2 seconds for registration.
•
If the “---” icon appears on the outdoor remote sensor, move the unit closer to the receiving unit. Repeat the
registration procedure again.
•
The channels will be automatically assigned to the sensors respectively in sequence of registration.
However, if all sensors are already registered, you can perform the registration again by selecting the desired channel
and hold “Channel” for 2 seconds to enable the receiving unit to receive RF temperature signals.
For wireless remote sensor with detachable probe only
If measurement of water, soil, or other liquid is desired, open the cover of the plug hole at the side of the sensor and
insert the probe plug. (optional)
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.1
Linearized                      : No
Page Count                      : 1
Create Date                     : 1910:31:10 31:35:65
Producer                        : Acrobat Distiller 3.0 for Windows
Title                           : 683F33
Subject                         : 683F33
Author                          : eunice
Creator                         : Adobe PageMaker 6.5
EXIF Metadata provided by EXIF.tools
FCC ID Filing: N9Z001H22

Navigation menu