Ewig Macao Commercial Offshore THX301M Part 15 Security / Remote Control Transmitter User Manual Thermo sensor

Download:
Mirror Download [FCC.gov]
Document ID	649107
Application ID	CYtV1QbThCk0k/qQ2in9zw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.23kB (140407 bits)
Date Submitted	2006-04-20 00:00:00
Date Available	2006-04-17 00:00:00
Creation Date	2006-04-11 10:39:26
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2006-04-11 10:39:39
Document Title	Thermo sensor
Document Creator	Acrobat PDFMaker 5.0 for Word
Document Author:	Ken Tsoi

Thermo sensor
Model: THX301
Instruction Manual
Congratulations on your of purchasing our new long range outdoor
thermo-hygrometer senor which can cover up to 75m range in an open
area. This sensor is designed for everyday use for the home or office and
used to monitor the temperature and humidity change of outdoor sites.
Features
A. LED indicator
Flashes when remote unit transmits a reading.
B. Channel number
Indicates the remote sensor is set to which channel and the user can find the
corresponding reading in the same channel in the linked receiving unit.
C. Temperature/humidity display
Display the measured temperature and humidity
Description of buttons
The remote sensor has 3 function buttons inside the battery compartment
1. [CH] button
After the battery installation, the LED blinks slowly every 1.5 seconds and channel
number shows ‘1’ to indicate it is now under channel setting mode and is set to
channel 1 by default. If the user presses no key within ten seconds, the unit will
auto-exit the channel setting.
If the user press [CH] button once during the channel setting, the channel number
is changed to ‘2’ to indicate the unit is set to channel 2. If the user press [CH]
button again, the channel number will be advanced to channel ‘3’ and so on.
The maximum channel number is ‘5’ and the unit will be scrolled back to channel
‘1’ at the 5th press of the [CH] button.
2. [C/F] button
Press to toggle unit °C or °F
3. [ RESET ] Button
Press to hardware reset the unit to factory setting
Setting procedure to link up with a receiving unit
This device is designed for easy set up with no wire installation. The following steps are
required to be done in proper sequence to link up with a receiving unit. Please insert
batteries for the receiving unit before doing so for the remote unit.
1. Remove the bracket stand.
2. Unlock two latches in the bottom to release the semi-transparent jacket.
3. Slide down the battery door in the back.
4. Insert 2 pieces AAA size batteries according to polarity marking on the
battery compartment.
5. The LED blinks slowly to indicate it is under the channel setting mode and the
user can set it to other channel by press [CH] key.
6. The temperature of the sensor will appear on the selected channel of the
receiving unit if it is linked up with the receiving unit successfully.
7. Close the battery door and use two latches in the bottom to lock it with the
semi-transparent jacket. Follow the same procedure (1 to 7) to register other
remote sensors.
Note: For the user purchasing more than one remote sensor, he must set the sensors to
different channel in the start up to avoid conflicts.
Precautions
a. Do not clean the unit with abrasive or corrosive compound. It may scratch the
plastic parts and corrode the electronic circuits.
b. Do not subject the unit to excessive force shock, dust, temperature or humidity,
which may result in malfunctioning, shorter electronic life span, damaged battery
and distorted parts.
c. Do not tamper with these units’ internal components. Doing so will invalidate the
warranty on the unit and may cause unnecessary damage battery and distorted
parts.
d. Do not subject the unit to excessive exposure to direct sunlight. The remote sensor
is splash proof. Never immerse it in water or expose to heavy rain.
e. Always read the users manual thoroughly before operating the unit.
Specification
Displayed temperature range : -50.0°C to +70.0°C (-58.0°F to +158.0°F)
Proposed operating range : -20.0°C to +60.0°C (-4.0°F to +140.0°F)
Temperature resolution : 0.1°C (0.2°F)
Displayed range
20% to 99%
Proposed operating range
20% to 99%
RF transmission frequency : 433MHz
RF transmission range : Maximum 75 meters in open area
Batteries : Use 2 pieces UM-4 AAA size 1.5V alkaline battery
This device could be sensitive to electrostatic discharge, If electrostatic discharge or
malfunctioning occurs please reset this unit.
CAUTION
The above content is subject to change without notice.
The displays printed in this manual may be different from the actual display because
of printing limitations.
The manufacturer and its suppliers hold no responsibility to you or any other person for
any damage expenses, lost profits, or any other claims arisen by using this product.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: -- Reorient or relocate the
receiving antenna. -- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. -- Consult the dealer or an experienced radio/TV technician for
help
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: -- Reorient or relocate the
receiving antenna. -- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected. -- Consult the dealer or an experienced radio/TV technician for
help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2006:04:11 10:39:39+08:00
Create Date                     : 2006:04:11 10:39:26+08:00
Page Count                      : 4
Creation Date                   : 2006:04:11 02:39:26Z
Mod Date                        : 2006:04:11 02:39:26Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : Ken Tsoi
Metadata Date                   : 2006:04:11 02:39:26Z
Creator                         : Ken Tsoi
Title                           : Thermo sensor
Page Mode                       : UseNone
Tagged PDF                      : Yes

EXIF Metadata provided by EXIF.tools