Export Management System EZCODEM300 Garage door transmitter User Manual 110604 EZ M300 MANUALx

Download:
Mirror Download [FCC.gov]
Document ID	1529980
Application ID	WF4v/URppPt7EB1bxBPkkQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.18kB (139785 bits)
Date Submitted	2011-08-26 00:00:00
Date Available	2011-08-26 00:00:00
Creation Date	2011-08-17 10:50:08
Producing Software	AFPL Ghostscript 8.53
Document Lastmod	2011-08-17 10:50:08
Document Title	Microsoft Word - 110604 EZ-M300 MANUAL.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	randy.clark

EZ Code-M300 Transmitter
PRODUCT INSTRUCTION
EZ Code-M300 is the mini transmitter designed for garage door opener and gate
operators for home, farm and ranch etc…
OPERATING INSTRUCTIONS:
Code Setting
1. You may set your transmitter to any code you desire but be sure that
the code you set matches the code that has been set on your radio
receiver.The digital code is determined by the positions of the 10 small
switches numbered 1 through 10 located in the receiver and transmitter.
2. Remove the one Philips head screw located on the back of the case and
carefully separate the case halves to expose the circuit board and battery.
(See Diagram #1)
Door button
operation indicator
Battery
Door (gate)
Open/Close
Code switch
DIAGRAM #1
1. Using a sharp object or tool, such as a paper clip, se the new transmitter
code by setting the “ON” and “OFF” switches according to the exact code
setting of your previous transmitter or the receiver. (Note: The switches are in
the “ON” positions when the switch is pushed toward the letter ON.)
(See Diagram #2)
2.
Once the codes have been set, replace the top cover, and test the system.
Note:
In
order
to
avoid
duplication
of
your
access
code,
the
following
sequences are not recommended.
•
Alternating from “ON” and “OFF” or “OFF” and “ON” position.
•
Setting the switch on all “ON” or all “OFF” position.
•
It is important for the access code to be set exactly in the same order as
the receiver for the transmitter to function properly.
Testing the Transmitter:
1.
Standing approximately 10-30 feet away from the receiver, push the transmitter
button to activate.
2.
Stand
in
several
different
areas
of
usage
to
locate
possible
points
where
certain structures may interfere with the transmission.
General specification & Feature:
1.
Output Power: -37dBm
2.
Output Frequency: 300MHz
3.
Power Supply: 12Vdc(5Vdc Regulation)
4.
Operation Indicate LED Lamp
Note:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed
and
interference
used
to
in
radio
accordance
with
communication.
the
instructions,
However,
there
is
may
no
cause
harmful
guarantee
that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning
the
equipment
off
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference by one or more of the following measures;
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Caution: Any changes or modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
DISTRIBUTED BY
Export Management System Inc.
Hawthorne CA 90250

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
Producer                        : AFPL Ghostscript 8.53
Create Date                     : 2011:08:17 10:50:08
Modify Date                     : 2011:08:17 10:50:08
Title                           : Microsoft Word - 110604 EZ-M300 MANUAL.docx
Creator                         : PScript5.dll Version 5.2.2
Author                          : randy.clark

EXIF Metadata provided by EXIF.tools