Extreme Networks AP3917I Wireless 802.11 a/ac+b/g/n Access Point User Manual AP3917i

Download:
Mirror Download [FCC.gov]
Document ID	3642862
Application ID	1OiKYswucFLwwF/2jFdFeg==
Document Description	User Manual AP3917i
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	55.81kB (697593 bits)
Date Submitted	2017-11-17 00:00:00
Date Available	2017-11-17 00:00:00
Creation Date	2017-01-11 16:08:32
Producing Software	Acrobat Distiller 17.0 (Windows)
Document Lastmod	2017-10-18 16:03:10
Document Title	WS-AP3917i-FCC WS-AP3917i-ROW WS-AP3917e-FCC WS-AP3917e-ROW Wireless Access Points Quick Reference
Document Creator	FrameMaker 2017
Document Author:	Extreme Networks

Installing the ExtremeWireless Outdoor
AP3917i/e Access Point
Mounting the AP3917i/e to a Wall
1 IoT/BLE Radio
2 Radio - 5 GHz
Overview of the AP3917i/e
4 Status
5 GE1 (PoE IN)
6 GE2
7 Console/Reset
8 2.4 G - Antenna 1 and 2
2 Drill four holes into the wall as follows:
9 Vent
10 5G - Antenna 1
Note: The AP3917i/e requires a minimum base firmware of 10.41.
11 BLE/802.15.4 Antenna
The AP3917i/e model has the following features:
• Radios: 2 radios (2.4GHz and 5GHz); 1 IoT/BLE/802.15.4 Radio (2.4 GHz)
• Console Port: RJ45
• One RJ45, 10/100/1000 Ethernet Port (GE1) with PoE
• One RJ45, 10/100/1000Mb Ethernet Port (GE2)
• IP67 Connectors on all ports
• LEDs: 4 (see Figure 1)
• One Reset button
• Power: PoE 802.3af or 802.3at
• GPS Receiver (will be supported via a future firmware release)
• Antennas:
– AP3917i - 5 internal antennas (four band locked antennas and one BLE
antenna). The polarization on one antenna of each radio can be
configured by the installer.
– AP3917e- 5 external antennas (four single band antennas and one BLE
antenna)
• Temperature: -40 to 70*C ambient temperature
• Enclosure: Cast Aluminum base and outdoor rated PC cover
12 5 G - Antenna 2
LEDs on the Front of the AP
Both the Radio LEDs will be Green when they are ON and the LEDs will not
have any lights when they are OFF. Blue LED indicates the IoT status.
For detailed installation information about the AP3917i/e, see the
ExtremeWireless AP3917i/e Installation Guide.
Table 1 shows ways to power the AP3917i/e.
Table 1 Powering the AP3917i/e
Figure 3
Figure 1
Quantity Item
Use small cable clamp.
5” - 7” (178mm)
Use large cable clamp
For other pole diameters, provide your own stainless steel cable clamp.
The band must be ½” (12.7mm) wide.
2 Attach the AP to the “Pole Mount” bracket using four M4 screws. Tighten
the four screws to a torque of 13.0-13.5 in-lbs.
Figure 6
Attaching a Pole Bracket to the AP
Power is provided through the RJ45 Ethernet port (GE1 port).
3 Attach the cable clamp to the pole bracket. Open the cable clamp by
turning a flat bladed screwdriver counterclockwise. Then, insert the nonclamp end into the pole bracket through the holes.
Note: It is easier to install both clamps before attaching to the pole.
Verify the contents of the box and ensure that the following items are
available:
Table 2
<= 2.5” (63.5mm)
Attaching the “H” Bracket to the AP
Verifying the AP3917i/e Box Contents
Figure 1 indicates AP3917i. In Figure 2, you can see AP3917e.
Top and Side Views of AP3917i
– for installing the AP on a masonry wall, use a 5/16” diameter bit.
– for other materials, use the appropriate drill for the screws being used.
3 For masonry installations, drill at least 1/8” (3mm) past the depth of the
screw, or bolt, being used, and place four anchor assemblies into the
holes.
4 Attach the AP to the “H” Bracket:
a Use 4 M4 screw assemblies to attach the AP to the “H” bracket on the
side that does not have the PEM stand-offs.
b Tighten the four screws to a torque of 13.0-13.5 in-lbs.
Cable Clamp Size
Description
Power Source
Power over
Ethernet
(PoE)
Using the mounting bracket as a guide, mark the location for the
mounting screws. The wall bracket provides eight attachment holes. Use
four (one in each corner), Place the bracket and mark the four hole
centers.
Determine the diameter of the pole.
Pole Diameter
Note: The “H” type Mounting Bracket (WS-MBO-H01) is sold as a
separate accessory (ordering part #30519).
3 Radio - 2.4 GHz
The AP3917 is an IP67 rated outdoor Access Point with 802.11ac dual band 2:2
radios. The AP3917 is easy to install, lightweight, and is available in an internal
(AP3917i) and external (AP3917e) antenna model. Each model includes 802.11
radios, an IoT radio, and a GPS radio. The AP3917 model comes in two models:
AP3917i and AP3917e. In this document, the functionality, feature, and the
procedure applies to both the models when AP3917i/e is used.
4 Put the metal band around the pole and insert it into the clamp. Turn the
clamp screw clockwise, tightening the band around the pole.
Contents of the AP3917i/e Box
AP3917i/e Quick Reference Guide
Cloud Quick Start Card
The following hardware is included:
M4 screw assembly with star washer
Ring terminal
5 Secure the anchors to the wall, then secure the bracket to the anchors.
6 If using #10 screws, tighten them to a torque of 25 in-lbs. If using ¼”
screws, tighten them to 45 in-lbs.
Figure 4
AP3917i Wall Mount “H” Bracket
Figure 5
AP3917e Wall Mount “H” Bracket
Figure 7
AP with Mounting Bracket—Vertical Pole
Mounting and Connecting the AP
Electrical Hazard: Only qualified personnel should perform
installation procedures.
1 IoT/BLE Radio
2 Radio - 5 GHz
3 Radio - 2.4 GHz
4 Status
5 GE1 (PoE IN)
6 GE2
7 Console/Reset
8 Vent
Figure 2
Top and Side Views of AP3917e
Use these instructions as guidelines for mounting and connecting the
AP3917i/e easily and safely.
The AP3917i/e mounting brackets are sold separately.
For more information about installing the optional bracket and the adapter,
see the ExtremeWireless AP3917i/e Installation Guide.
For installation videos of the AP, see www.extremenetworks.com/support/.
Mounting the AP3917i/e
The installation of the AP3917i/e should be performed by a professional
installer to ensure proper operation and compliance with local safety
guidelines.
The access point can be mounted to a wall, girder, ceiling, pole or vehicle
using the appropriate bracket.
Mounting the AP3917i/e to a Wall/Pole using
the WS-MBO-ART01 2 Axis Extension Arm
You can mount the AP3917i/e to a wall or a pole using a 10” extension arm
(WS-MBO-ART01, ordering part #30514). For mounting and installation
instructions, refer to the ExtremeWireless AP3917i/e Installation Guide.
Positioning the AP for Installation
Installing External Antennas
Mount the AP so that the glands are on the side of the AP closest to the
ground, and not above the plastic cover. You must provide a 3-inch drip loop
on all cables.
Professionally install the external antennas intended for area coverage.
For information about antenna selection and installation, refer to the
External Antenna Site Preparation and Installation Guide.
2 Attach the external antenna cables to the Standard Polarity Type-N
connectors on the AP3917i/e.
Note: Do not remove the dust cap until you need to install the BLE/
IoT antennas.
Connecting a Power Source to the AP3917i/e
Attach the Ground Wire
Use the M4 ground screw assembly, with the star washer, to attach the
ground wire’s ring terminal to the back of the AP. The wire should be as close
to the AP bottom as possible. Tighten the screw to a torque of 13.0-13.5 inlbs.
Note: Attach the H bracket after attaching the ground wire onto the
AP. Once you tighten the torque, tighten the ground screws, and
attach the LAN cable.
If you need to power the AP3917i/e, you can do so my using the GE1 port on
the AP. The power LED on the front face of the AP illuminates when the device
is connected to a power source. Refer to the ExtremeWireless AP3917i/e
Installation Guide for information.
Mounting the AP3917i/e to a Pole
Note: The Pole Mounting Bracket (WS-MBO-POLE01) is sold as a
separate accessory (ordering part #30520).
LAN/Console Connections
The AP3917i/e has one LAN (Ethernet) port and a Console port. Refer to
Figure 1 for the location of these ports. During administration and
maintenance through the LAN or Console, the AP must still have a power
connection through either an Ethernet PoE cable or a DC power supply.
Professional Installation Instruction
Installation personnel
This product is designed for specific application and needs to be installed by a
qualified personnel who has RF and related rule knowledge. The general user
shall not attempt to install or change the setting.
Installation location
The product shall be installed at a location where the radiating antenna can be
kept 20 cm from nearby person in normal operation condition to meet
regulatory RF exposure requirement.
External antenna
Use only the antennas which have been approved by the applicant. The nonapproved antenna(s) may produce unwanted spurious or excessive RF
transmitting power which may lead to the violation of ISED limit and is
prohibited.
Installation procedure
Please refer to user’s manual for the detail.
Warning: Please carefully select the installation position and make sure that
the final output power does not exceed the limit set force in relevant rules. The
violation of the rule could lead to serious federal penalty.
Instructions d'installation professionnelle
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Operations in the 5.15-5.25GHz frequency range, it is restricted to indoor
environment.
This device meets all the other requirements specified in Part 15E, Section
15.407 of the FCC Rules.
Warning: FCC Radiation Exposure Statement: This equipment
complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your
body.
Industry Canada Notice
This device complies with ISED’s licence-exempt RSSs. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.
Caution :
Ce produit est destine a un usage specifique et doit etre installe par un
personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant.
L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final.
Emplacement d'installation
En usage normal, afin de respecter les exigences reglementaires concernant
l'exposition aux radiofrequences, ce produit doit etre installe de facon a
respecter une distance de 20cm entre l'antenne emettrice et les personnes.
The symbol above indicates that separate collection of electrical and electronic
equipment is required.
2 When this product has reached the end of its serviceable life, it cannot be disposed of
as unsorted municipal waste. It must be collected and treated separately.
3 It has been determined by the European Parliament that there are potential negative
effects on the environment and human health as a result of the presence of hazardous
substances in electrical and electronic equipment.
4 It is the users’ responsibility to utilize the available collection system to ensure WEEE
is properly treated.
Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation
d'autres antennes peut conduire a un niveau de rayonnement essentiel ou non
essentiel depassant les niveaux limites definis par ISED, ce qui est interdit.
Procedure d'installation
Consulter le manuel d'utilisation.
Warning: Avertissement: Choisir avec soin la position d'installation et
s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La
violation de cette regle peut conduire a de serieuses penalites federales.
Regulatory and Compliance Information
Safety Guidelines
This section contains notices that are intended to protect your personal safety
and prevent damage to the equipment.
Qualified Personnel:
Electrical Hazard: Only qualified personnel should perform
installation procedures. Within the context of the safety notes in this
documentation, qualified persons are defined as persons who are
authorized to commission, ground and label devices, systems, and
circuits in accordance with established safety practices and
standards. A qualified person understands the requirements and risks
involved with installing outdoor electrical equipment in accordance
with national codes.
Warning: Déclaration d'exposition aux radiations: Cet
équipement est conforme aux limites d'exposition aux rayonnements
ISED établies pour un environnement non contrôlé. Cet équipement
doit être installé et utilisé avec un minimum de 20 cm de distance
entre la source de rayonnement et votre corps.
31050 WS-AP3917i-FCC
31051 WS-AP3917i-ROW
31055 WS-AP3917e-FCC
31056 WS-AP3917e-ROW
Hazardous Substances
Declaration of Conformity in Languages of the
European Community
English
Hereby, Extreme Networks, declares that this Radio LAN device is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Finnish
Valmistaja Extreme Networks vakuuttaa täten että Radio LAN device
tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
Dutch
Hierbij verklaart Extreme Networks dat het toestel Radio LAN device
in overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG.
Bij deze verklaart Extreme Networks dat deze Radio LAN device
voldoet aan de essentiële eisen en aan de overige relevante
bepalingen van Richtlijn 1999/5/EC.
French
Par la présente Extreme Networks déclare que l'appareil Radio LAN
device est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE.
Par la présente, Extreme Networks déclare que ce Radio LAN device
est conforme aux exigences essentielles et aux autres dispositions de
la directive 1999/5/CE qui lui sont applicables.
Swedish
Härmed intygar Extreme Networks att denna Radio LAN device står I
överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Danish
Undertegnede Extreme Networks erklærer herved, at følgende udstyr
Radio LAN device overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF.
German
Hiermit erklärt Extreme Networks die Übereinstimmung des "WLAN
Wireless Controller bzw. Access Points" mit den grundlegenden
Anforderungen und den anderen relevanten Festlegungen der
Richtlinie 1999/5/EG.
Greek
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Extreme Networks ∆ΗΛΩΝΕΙ ΟΤΙ Radio LAN
device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ
ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/
ΕΚ.
Icelandic
Extreme Networks lysir her med yfir að thessi bunadur, Radio LAN
device, uppfyllir allar grunnkrofur, sem gerdar eru i R&TTE tilskipun
ESB nr 1999/5/EC.
Italian
Con la presente Extreme Networks dichiara che questo Radio LAN
device è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Federal Communications Commission (FCC) Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate this equipment.
P/N
P/N
P/N
P/N
This product complies with the requirements of Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011 on the restriction of the
use of certain hazardous substances in electrical and electronic equipment.
Avertissement:
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les
mêmes canaux;
2 le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de
5725 à 5 850 MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour
l'exploitation point à point et l’exploitation non point à point, selon le cas;
3 De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de
radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.,
qu’ils ont la priorité) pour les bandes 5650-5850 MHz et que ces radars
pourraient causer du brouillage et/ou des dommages aux dispositifs LANEL.
Warning: IC Radiation Exposure Statement: This equipment
complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your
body.
TM
For information about the available collection system, please contact
Extreme Customer Support at +353 61 705500 (Ireland).
Antenn externe
ExtremeWireless
Access Points
Quick Reference
In accordance with Directive 2012/19/EU of the European Parliament on waste
electrical and electronic equipment (WEEE):
Installation
The device for operation in the band 5150-5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile
satellite systems;
2 The maximum antenna gain permitted for devices in the band 5725-5850
MHz shall be such that the equipment still complies with the e.i.r.p. limits
specified for point-to-point and non-point-to-point operation as
appropriate; and
3 Users should also be advised that high-power radars are allocated as
primary users (i.e. priority users) of the bands 5650-5850 MHz and that
these radars could cause interference and/or damage to LE-LAN devices.
European Waste Electrical and Electronic Equipment
(WEEE) Notice
Spanish
Por medio de la presente Extreme Networks declara que el Radio LAN
device cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Portuguese
Extreme Networks declara que este Radio LAN device está conforme
com os requisitos essenciais e outras disposições da Directiva 1999/5/
CE.
Malti
Hawnhekk, Extreme Networks, jiddikjara li dan Radio LAN device
jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn
relevanti li hemm fid-Dirrettiva 1999/5/EC.
Notice
Copyright © 2017 Extreme Networks, Inc. All Rights Reserved.
Legal Notices
Extreme Networks, Inc., on behalf of or through its wholly-owned subsidiary,
Enterasys Networks, Inc., reserves the right to make changes in specifications
and other information contained in this document and its website without
prior notice. The reader should in all cases consult representatives of Extreme
Networks to determine whether any such changes have been made.
The hardware, firmware, software or any specifications described or referred
to in this document are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or
registered trademarks of Extreme Networks, Inc. in the United States and/or
other countries.
All other names (including any product names) mentioned in this document
are the property of their respective owners and may be trademarks or
registered trademarks of their respective companies/owners.
For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation & Support
For product support, including documentation, visit:
www.extremenetworks.com/support/
P/N 9035165-02

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Language                        : en
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.150055, 2012/11/19-18:45:32
Format                          : application/pdf
Title                           : WS-AP3917i-FCC WS-AP3917i-ROW WS-AP3917e-FCC WS-AP3917e-ROW  Wireless Access Points Quick Reference
Creator                         : Extreme Networks
Create Date                     : 2017:01:11 16:08:32Z
Creator Tool                    : FrameMaker 2017
Modify Date                     : 2017:10:18 16:03:10-04:00
Metadata Date                   : 2017:10:18 16:03:10-04:00
Producer                        : Acrobat Distiller 17.0 (Windows)
Document ID                     : uuid:88144be5-7407-4bcc-a175-ebd343893596
Instance ID                     : uuid:aaed741e-e95f-424f-80b7-6b1925690254
Page Mode                       : UseNone
Page Count                      : 2
Author                          : Extreme Networks

EXIF Metadata provided by EXIF.tools