Extreme Networks AP3917I Wireless 802.11 a/ac+b/g/n Access Point User Manual AP7662i

Extreme Networks, Inc. Wireless 802.11 a/ac+b/g/n Access Point AP7662i

UserManual.wiki >

Extreme Networks >

AP3917I User Manual >

User Manual AP7662i

Contents

1. User Manual AP3917i
2. User Manual AP7662i

User Manual AP7662i

Installing the ExtremeWiNG Outdoor AP-7662i/e Access PointOverview of the AP-7662i/eThe AP-7662 is an IP67 rated outdoor Access Point with 802.11ac dual band 2:2 radios. The AP-7662 is easy to install, lightweight, and is available in an internal (AP-7662i) and external (AP-7662e) antenna model. Each model includes 802.11 radios, an IoT radio, and a GPS radio. The AP-7662 model comes in two models: AP-7662i and AP-7662e. In this document, the functionality, feature, and the procedure applies to both the models when AP-7662i/e is used.The AP-7662i/e model has the following features:• Radios: 2 radios (2.4GHz and 5GHz); 1 IoT/BLE/802.15.4 Radio (2.4 GHz)•Console Port: RJ45• One RJ45, 10/100/1000 Ethernet Port (GE1) with PoE • One RJ45, 10/100/1000Mb Ethernet port (GE2)• IP67 Connectors on all ports•LEDs: 4 (see Figure 1)•One Reset button • Power: PoE 802.3af or 802.3at• GPS Receiver (will be supported via a future firmware release)• Antennas:– AP-7662i - Five internal antennas (four band locked antennas and one BLE antenna)– AP-7662e- Five external antennas (four single band antennas and one BLE antenna)• Temperature: -40 to 70*C ambient temperature • Enclosure: Cast Aluminum base and TopIn Figure 1, the top image indicates AP-7662i. Figure 2 shows the top and side views of AP-7662e.Figure 1 Top and Side Views of AP-7662iFigure 2 Top and Side Views of AP-7662eNote: The AP-7662i/e requires a minimum base firmware of WiNG 5.9.1.1IoT/BLE Radio2Radio - 5 GHz3Radio - 2.4 GHz4Status5GE1 (PoE IN)6GE27Console/Reset8VentLEDs on the Front of the APAmber LEDs indicate 5 GHz Wi-Fi Radio, Green LEDs indicate 2.4 GHz Wi-Fi Radio, and Blue LED indicates the IoT Radio. The Status LED is ON only during bootup.For detailed installation information about the AP-7662i/e, see the ExtremeWireless AP-7662i/e Installation Guide.Tabl e 1 shows ways to power the AP-7662i/e.Table 1 Powering the AP-7662i/e Verifying the AP-7662i/e Box ContentsVerify the contents of the box and ensure that the following items are available:Mounting and Connecting the APUse these instructions as guidelines for mounting and connecting the AP-7662i/e easily and safely. The AP-7662i/e mounting brackets are sold separately.For more information about installing the optional bracket and the adapter, see the ExtremeWireless AP-7662i/e Installation Guide.For installation videos of the AP, see www.extremenetworks.com/support/Mounting the AP-7662i/eUse these instructions as guidelines for mounting and connecting the AP-7662i/e easily and safely. The installation of the AP-7662i/e should be performed by a professional installer to ensure proper operation and compliance with local safety guidelines.Attach the AP-7662i/e to a surface that can support the AP and in an environment it can withstand. It can be mounted to a wall, girder, ceiling, or pole, and the surface material can be concrete, brick, wood, metal, or plastic. Positioning the AP for InstallationMount the AP so that the glands are on the side of the AP closest to the ground, and not above the plastic cover. You must provide a 3-inch drip loop on all cables. Attach the Ground WireUse the M4 ground screw assembly, with the star washer, to attach the ground wire’s ring terminal to the back of the AP. The wire should be as close to the AP bottom as possible. Tighten the screw to a torque of 13.0-13.5 in-lbs.1IoT/BLE Radio2Radio - 5 GHz3Radio - 2.4 GHz4Status5GE1 (PoE IN)6GE27Console/Reset82.4 G - Antenna 1 and 29Vent10 5G - Antenna 111 BLE/802.15.4 Antenna12 5 G - Antenna 2Power Source DescriptionPower over Ethernet (PoE) Power is provided through the RJ45 Ethernet port (GE1 port).Table 2 Contents of the AP-7662i/e BoxQuantity Item1 AP-7662i/e Quick Reference Guide1 Cloud Quick Start CardThe following hardware is included:1 M4 screw assembly with star washer1 Ring terminalElectrical Hazard: Only qualified personnel should perform installation procedures.Note: Do not remove the dust cap until you need to install the BLE/IoT antennas. Note: Attach the H bracket after attaching the ground wire onto the AP. Tighten the torque, tighten the screws, and attach the LAN cable. Mounting the AP-7662i/e to a Wall1 Using the mounting bracket as a guide, mark the location for the mounting screws. The wall bracket provides eight attachment holes. Use four (one in each corner). Place the bracket and mark the four hole centers.2 Drill four holes into the wall as follows:– for installing the AP on a masonry wall, use a 5/16” diameter bit.– for other materials, use the appropriate drill for the screws being used.3 For masonry installations, drill at least 1/8” (3mm) past the depth of the screw, or bolt, being used, and place four anchor assemblies into the holes.4 Attach the AP to the “H” Bracket:a Use four M4 screw assemblies to attach the AP to the “H” bracket on the side that does not have the PEM stand-offs. b Tighten the four screws to a torque of 13.0-13.5 in-lbs. Figure 3 Attaching the “H” Bracket to the AP 5 Secure the anchors to the wall, then secure the bracket to the anchors.6 If using #10 screws, tighten them to a torque of 25 in-lbs. If using ¼” screws, tighten them to 45 in-lbs.Figure 4 AP-7662i Wall Mount “H” BracketFigure 5 AP-7662e Wall Mount “H” BracketMounting the AP-7662i/e to a PoleNote: The “H” type Mounting Bracket (WS-MBO-H01) is sold as a separate accessory (ordering part #30519). Note: The Pole Mounting Bracket (WS-MBO-POLE01) is sold as a separate accessory (ordering part #30520). 1 Determine the diameter of the pole. For other pole diameters, provide your own stainless steel cable clamp. The band must be ½” (12.7mm) wide.2 Attach the AP to the “Pole Mount” bracket using 4 M4 screws. Tighten the four screws to a torque of 13.0-13.5 in-lbs. Figure 6 Attaching a Pole Bracket to the AP 3 Attach the cable clamp to the pole bracket. Open the cable clamp by turning a flat bladed screwdriver counterclockwise. Then, insert the non-clamp end into the pole bracket through the holes.4 Put the metal band around the pole and insert it into the clamp. Turn the clamp screw clockwise, tightening the band around the pole. Figure 7 AP with Mounting Bracket—Vertical PoleMounting the AP-7662i/e to a Wall/Pole using the WS-MBO-ART01 2 Axis Extension ArmYou can mount the to AP-7662i/e to a wall or a pole using a 10” extension arm (WS-MBO-ART01, ordering part #30514). For mounting and installation instructions, refer to the ExtremeWireless AP-7662i/e Installation Guide. Installing External Antennas1 Professionally install the external antennas intended for area coverage. For information about antenna selection and installation, refer to the External Antenna Site Preparation and Installation Guide. 2 Attach the external antenna cables to the Standard Polarity Type-N connectors on the AP-7662i/e.Connecting a Power Supply to the AP-7662i/eIf you need to power the AP-7662i/e, you can do so my using the GE1 port on the AP. The power LED on the front face of the AP illuminates when the device is powered on. Refer to the ExtremeWireless AP-7662i/e Installation Guide for more information.LAN/Console ConnectionsThe AP-7662i/e has two LAN (Ethernet) ports and a Console port. Refer to Figure 1 and Figure 2 for the location of these ports. During administration and maintenance through the LAN or Console, the AP must still have a power connection through either an Ethernet PoE cable or a DC power supply.Pole Diameter Cable Clamp Size<= 2.5” (63.5mm) Use small cable clamp.5” - 7” (178mm) Use large cable clampNote: It is easier to install both clamps before attaching to the pole.

Navigation menu