Extreme Networks AP3917K Wireless 802.11 a/ac+b/g/n PCBA module User Manual AP3917k
Extreme Networks, Inc. Wireless 802.11 a/ac+b/g/n PCBA module AP3917k
Contents
AP3917k User Manual
Installing the ExtremeWireless Outdoor AP3917k Access Point Overview of the AP3917k The AP3917k is a board only model. It does not have any enclosures or antennas. The users can integrate the AP3917k board into their solution. Note: The AP3917k requires a minimum base firmware of 10.41. Verifying the AP3917k Box Contents Verify the contents of the box and ensure that the following items are available: Regulatory and Compliance Information Safety Guidelines This section contains notices that are intended to protect your personal safety and prevent damage to the equipment. Qualified Personnel: Electrical Hazard: Only qualified personnel should perform installation procedures. Within the context of the safety notes in this documentation, qualified persons are defined as persons who are authorized to commission, ground and label devices, systems, and circuits in accordance with established safety practices and standards. A qualified person understands the requirements and risks involved with installing outdoor electrical equipment in accordance with national codes. Table 1 Contents of the AP3917k Box Quantity Item AP3917k Quick Reference Guide AP3917k board Unpacking Instructions The AP3917k board comes in an ESD (Electrostatic discharge) bag and is sealed using an ESD label. The board also includes four pin-headers to attach to any box that the user might be using the board on. Note: Remove the protective pin-header cap from the board before installing it. Guidance to the Host Manufacturer We hereby acknowledge our responsibility to provide guidance to the host manufacturer in the event that they require assistance for ensuring compliance with the Part 15 Subpart B requirements. 2 The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with the Part 15 Subpart B requirements, the host manufacturer is required to show compliance with the Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module’s intentional emissions are compliant (i.e. fundamental and out of band emissions) with the Radio essential requirements. The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in the Part 15 Subpart B or emissions are complaint with the Radio aspects. Warning: Using the Board To integrate the board: 1 Slide the board out of the bag. 2 Install the board into the target system. 3 Connect WiFi and IoT antennas according to the wiring instructions. 4 Connect PoE network connection. Electrical Hazard: Use ESD protection wrist wrap when installing the AP3917k board. Refer to the ExtremeWireless AP3917k Installation Guide for additional installation instructions. Notice Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The restriction of operating this device in indoor could void the user’s authority to operate the equipment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 31 cm between the radiator & your body. The FCC part 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Copyright © 2017 Extreme Networks, Inc. All Rights Reserved. Label of the end product Legal Notices Extreme Networks, Inc., on behalf of or through its wholly-owned subsidiary, Enterasys Networks, Inc., reserves the right to make changes in specifications and other information contained in this document and its website without prior notice. The reader should in all cases consult representatives of Extreme Networks to determine whether any such changes have been made. The hardware, firmware, software or any specifications described or referred to in this document are subject to change without notice. Trademarks Extreme Networks and the Extreme Networks logo are trademarks or registered trademarks of Extreme Networks, Inc. in the United States and/or other countries. All other names (including any product names) mentioned in this document are the property of their respective owners and may be trademarks or registered trademarks of their respective companies/owners. For additional information on Extreme Networks trademarks, please see: www.extremenetworks.com/company/legal/trademarks/ Documentation & Support For product support, including documentation, visit: www.extremenetworks.com/support/ The final end product must be labeled in a visible area with the following: "Contains TX FCC ID: QXO-AP3917K" The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Antenna Type Model Number Brand Name Antenna gain Frequency Omni ML-2499HPA8-01 Extreme 7.5 dBi 24002500MHz Omni ML-5299FHPA6-01R Extreme 7.75 dBi 49005875MHz Omni ML-5299HPA5-01 Extreme 5.6 dBi 51505850MHz Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device is restricted to indoor use. Warning: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 26 cm between the radiator & your body. The module is limited to OEM installation ONLY. This module is intended for OEM integrators under the following conditions: 1 This module is restricted to installation in products for use only in mobile and fixed applications. 2 The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 26 cm from all persons. 3 The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. 4 OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. 5 Fixed outdoor applications for point to multipoint operations are subject to the conditions in Part 15.407(a)(1)(i). The OEM integrator is still responsible for: 1 Ensuring that the end-user has no manual instructions to remove or install module. 2 The FCC compliance requirement of the end product, which integrates this module. 3 Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer. 4 The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. Industry Canada Notice This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. This radio transmitter IC: 4141B-AP3917K has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Warning: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 31 cm between the radiator & your body. Warning: Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 31 cm de distance entre la source de rayonnement et votre corps Antenna Type Model Number Brand Name Antenna gain Frequency Omni ML-2499HPA8-01 Extreme 7.5 dBi 24002500MHz Omni ML-5299FHPA6-01R Extreme 7.75 dBi 49005875MHz Omni ML-5299HPA5-01 Extreme 5.6 dBi 51505850MHz OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). Note: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. Modular OEM Integrator Notice End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 31 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains transmitter module IC: 4141B-AP3917K”. Contient le module d'émission IC: 4141B-AP3917K This device is intended only for OEM integrators under the following conditions: 1 The antenna must be installed such that 31 cm is maintained between the antenna and users, and 2 The transmitter module may not be co-located with any other transmitter or antenna. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1 L'antenne doit être installée de telle sorte qu'une distance de 31 cm est respectée entre l'antenne et les utilisateurs, et 2 Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Important Note for OEM integrator Antenna Type Model Number Brand Name Antenna gain Frequency Omni ML-2499HPA8-01 Extreme 7.5 dBi 24002500MHz Omni ML-5299FHPA6-01R Extreme 7.75 dBi 49005875MHz Omni ML-5299HPA5-01 Extreme 5.6 dBi 51505850MHz Le présent émetteur radio (IC: 4141B-AP3917K) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. This module is intended for OEM integrator. The OEM integrator is still responsible for: 1 ensuring that the end-user has no manual instructions to remove or install module 2 the ISED compliance requirement of the end product, which integrates this module 3 Appropriate measurements and if applicable additional equipment authorizations of the host device to be addressed by the integrator/ manufacturer. 4 The separate approval is required for all other operating configurations, including portable configurations and different antenna configurations The transmitter module may not be co-located with any other transmitter or antenna. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. CAN ICES-3 (B)/NMB-3(B) French Par la présente Extreme Networks déclare que l'appareil Radio LAN device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Par la présente, Extreme Networks déclare que ce Radio LAN device est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables. Swedish Härmed intygar Extreme Networks att denna Radio LAN device står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Danish Undertegnede Extreme Networks erklærer herved, at følgende udstyr Radio LAN device overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. German Hiermit erklärt Extreme Networks die Übereinstimmung des "WLAN Wireless Controller bzw. Access Points" mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Extreme Networks ∆ΗΛΩΝΕΙ ΟΤΙ Radio LAN device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ. Icelandic Extreme Networks lysir her med yfir að thessi bunadur, Radio LAN device, uppfyllir allar grunnkrofur, sem gerdar eru i R&TTE tilskipun ESB nr 1999/5/EC. Italian Con la presente Extreme Networks dichiara che questo Radio LAN device è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Spanish Por medio de la presente Extreme Networks declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Portuguese Extreme Networks declara que este Radio LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Malti Hawnhekk, Extreme Networks, jiddikjara li dan Radio LAN device jikkonforma mal-htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. European Waste Electrical and Electronic Equipment (WEEE) Notice In accordance with Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE): 1 The symbol above indicates that separate collection of electrical and electronic equipment is required. 2 When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately. 3 It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment. 4 It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated. For information about the available collection system, please contact Extreme Customer Support at +353 61 705500 (Ireland). Hazardous Substances This product complies with the requirements of Directive 2011/65/EU of the European Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Declaration of Conformity in Languages of the European Community English Hereby, Extreme Networks, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Finnish Valmistaja Extreme Networks vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/ 5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Dutch Hierbij verklaart Extreme Networks dat het toestel Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. ExtremeWireless Access Points Quick Reference P/N 31059 WS-AP3917k-FCC P/N 31060 WS-AP3917k-ROW Bij deze verklaart Extreme Networks dat deze Radio LAN device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. P/N 9035184-04 TM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Language : en XMP Toolkit : Adobe XMP Core 5.4-c005 78.150055, 2012/11/19-18:45:32 Format : application/pdf Creator : Extreme Networks Title : WS-AP3917k-FCC WS-AP3917k-ROW Wireless Access Points Quick Reference Create Date : 2017:01:11 16:08:32Z Creator Tool : FrameMaker 2017 Modify Date : 2017:11:30 10:41:12-05:00 Metadata Date : 2017:11:30 10:41:12-05:00 Producer : Acrobat Distiller 18.0 (Windows) Document ID : uuid:3f8ef641-a51a-46ec-84f8-d73c51523b05 Instance ID : uuid:2d0502d2-a087-43d3-bb99-6ec242ea0baa Page Mode : UseNone Page Count : 2 Author : Extreme NetworksEXIF Metadata provided by EXIF.tools