Extreme Networks AP3917K Wireless 802.11 a/ac+b/g/n PCBA module User Manual QXO AP3917K QSG AP3917k QuickRef User Man

Extreme Networks, Inc. Wireless 802.11 a/ac+b/g/n PCBA module QXO AP3917K QSG AP3917k QuickRef User Man

QXO-AP3917K-QSG_AP3917k_QuickRef User Man.

Installing the ExtremeWireless Outdoor
AP3917k Access Point
Overview of the AP3917k
The AP3917k is a board only model. It does not have any enclosures or
antennas. The users can integrate the AP3917k board into their solution.
Verifying the AP3917k Box Contents
Verify the contents of the box and ensure that the following items are
available:
Unpacking Instructions
The AP3917k board comes in an ESD (Electrostatic discharge) bag and is
sealed using an ESD label. The board also includes four pin-headers to attach
to any box that the user might be using the board on.
Using the Board
To integrate the board:
1 Slide the board out of the bag.
2 Install the board into the target system.
3 Connect WiFi and IoT antennas according to the wiring instructions.
4 Connect PoE network connection.
Refer to the ExtremeWireless AP3917k Installation Guide for additional
installation instructions.
Notice
Copyright © 2017 Extreme Networks, Inc. All Rights Reserved.
Legal Notices
Extreme Networks, Inc., on behalf of or through its wholly-owned subsidiary,
Enterasys Networks, Inc., reserves the right to make changes in specifications
and other information contained in this document and its website without
prior notice. The reader should in all cases consult representatives of Extreme
Networks to determine whether any such changes have been made.
The hardware, firmware, software or any specifications described or referred
to in this document are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or
registered trademarks of Extreme Networks, Inc. in the United States and/or
other countries.
All other names (including any product names) mentioned in this document
are the property of their respective owners and may be trademarks or
registered trademarks of their respective companies/owners.
For additional information on Extreme Networks trademarks, please see:
www.extremenetworks.com/company/legal/trademarks/
Documentation & Support
For product support, including documentation, visit:
www.extremenetworks.com/support/
Note: The AP3917k requires a minimum base firmware of 10.41.
Table 1 Contents of the AP3917k Box
Quantity Item
1AP3917k Quick Reference Guide
1AP3917k board
Note: Remove the protective pin-header cap from the board before
installing it.
Electrical Hazard: Use ESD protection wrist wrap when installing
the AP3917k board.
Regulatory and Compliance Information
Safety Guidelines
This section contains notices that are intended to protect your personal safety
and prevent damage to the equipment.
Qualified Personnel:
Guidance to the Host Manufacturer
1 We hereby acknowledge our responsibility to provide guidance to the host
manufacturer in the event that they require assistance for ensuring
compliance with the Part 15 Subpart B requirements.
2 The host manufacturer is responsible for additional testing to verify
compliance as a composite system. When testing the host device for
compliance with the Part 15 Subpart B requirements, the host
manufacturer is required to show compliance with the Part 15 Subpart B
while the transmitter module(s) are installed and operating. The modules
should be transmitting and the evaluation should confirm that the
module’s intentional emissions are compliant (i.e. fundamental and out of
band emissions) with the Radio essential requirements. The host
manufacturer must verify that there are no additional unintentional
emissions other than what is permitted in the Part 15 Subpart B or
emissions are complaint with the Radio aspects.
Warning:
1 Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
2 The restriction of operating this device in indoor could void the user’s
authority to operate the equipment.
3 This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
4 This equipment should be installed and operated with minimum distance 31
cm between the radiator & your body.
5 The FCC part 15.19 statement: This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Label of the end product
The final end product must be labeled in a visible area with the following:
"Contains TX FCC ID: QXO-AP3917K"
The end product shall bear the following 15.19 statement: This device complies
with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Federal Communications Commission (FCC) Interference
Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Electrical Hazard: Only qualified personnel should perform
installation procedures. Within the context of the safety notes in this
documentation, qualified persons are defined as persons who are
authorized to commission, ground and label devices, systems, and
circuits in accordance with established safety practices and
standards. A qualified person understands the requirements and risks
involved with installing outdoor electrical equipment in accordance
with national codes.
Antenna
Type
Model
Number
Brand
Name
Antenna
gain Frequency
Omini ML-2499-
HPA8-01 Extreme 7.5 dBi 2400-
2500MHz
Omini ML-5299-
FHPA6-01R Extreme 7.75 dBi 4900-
5875MHz
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
For product available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible. This device is restricted
to indoor use.
The module is limited to OEM installation ONLY.
This module is intended for OEM integrators under the following conditions:
1 This module is restricted to installation in products for use only in mobile
and fixed applications.
2 The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 26 cm from all persons.
3 The antenna(s) used for this transmitter must not transmit simultaneously
with any other antenna or transmitter.
4 OEM integrator has be limited the operation channels in channel 1-11 for
2.4GHz band.
5 Fixed outdoor applications for point to multipoint operations are subject to
the conditions in Part 15.407(a)(1)(i).
The OEM integrator is still responsible for:
1 Ensuring that the end-user has no manual instructions to remove or install
module.
2 The FCC compliance requirement of the end product, which integrates this
module.
3 Appropriate measurements (e.g. 15 B compliance) and if applicable
additional equipment authorizations (e.g. Verification, Doc) of the host
device to be addressed by the integrator/manufacturer.
4 The separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093 and different
antenna configurations.
Industry Canada Notice
This device complies with Industry Canada’s licence-exempt RSSs. Operation
is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris
un brouillage susceptible de provoquer un fonctionnement indésirable.
This radio transmitter IC: 4141B-AP3917K has been approved by Industry
Canada to operate with the antenna types listed below with the maximum
permissible gain indicated. Antenna types not included in this list, having a
gain greater than the maximum gain indicated for that type, are strictly
prohibited for use with this device.
Le présent émetteur radio (IC: 4141B-AP3917K) a été approuvé par Industrie
Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et
ayant un gain admissible maximal et l'impédance requise pour chaque type
d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority
to operate this equipment.
Warning: FCC Radiation Exposure Statement: This equipment
complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 26 cm between the radiator & your
body.
Antenna
Type
Model
Number
Brand
Name
Antenna
gain Frequency
Omini ML-2499-
HPA8-01 Extreme 7.5 dBi 2400-
2500MHz
Omini ML-5299-
FHPA6-01R Extreme 7.75 dBi 4900-
5875MHz
OEM integrator is still responsible for testing their end product for any
additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
Modular OEM Integrator Notice
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 31 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the
following: “Contains transmitter module IC: 4141B-AP3917K”.
Contient le module d'émission IC: 4141B-AP3917K
This device is intended only for OEM integrators under the following
conditions:
1 The antenna must be installed such that 31 cm is maintained between the
antenna and users, and
2 The transmitter module may not be co-located with any other transmitter
or antenna.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes: (Pour utilisation de dispositif module)
1 L'antenne doit être installée de telle sorte qu'une distance de 31 cm est
respectée entre l'antenne et les utilisateurs, et
2 Le module émetteur peut ne pas être coïmplanté avec un autre émetteur
ou antenne.
Important Note for OEM integrator
This module is intended for OEM integrator.
The OEM integrator is still responsible for:
1 ensuring that the end-user has no manual instructions to remove or install
module
2 the ISED compliance requirement of the end product, which integrates this
module
3 Appropriate measurements and if applicable additional equipment
authorizations of the host device to be addressed by the integrator/
manufacturer.
4 The separate approval is required for all other operating configurations,
including portable configurations and different antenna configurations
The transmitter module may not be co-located with any other transmitter or
antenna.
Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne.
Warning: IC Radiation Exposure Statement: This equipment
complies with IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 31 cm between the radiator & your
body.
Warning: Déclaration d'exposition aux radiations: Cet
équipement est conforme aux limites d’exposition aux rayonnements
IC établies pour un environnement non contrôlé. Cet équipement doit
être installé et utilisé avec un minimum de 31 cm de distance entre la
source de rayonnement et votre corps
Antenna
Type
Model
Number
Brand
Name
Antenna
gain Frequency
Omini ML-2499-
HPA8-01 Extreme 7.5 dBi 2400-
2500MHz
Omini ML-5299-
FHPA6-01R Extreme 7.75 dBi 4900-
5875MHz
Note: In the event that these conditions cannot be met (for example
certain laptop configurations or co-location with another transmitter),
then the IC authorization is no longer considered valid and the IC No.
cannot be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate IC authorization.
ExtremeWirelessTM
Access Points
Quick Reference
P/N 31059 WS-AP3917k-FCC
P/N 31060 WS-AP3917k-ROW
CAN ICES-3 (B)/NMB-3(B)
European Waste Electrical and Electronic Equipment
(WEEE) Notice
In accordance with Directive 2012/19/EU of the European Parliament on waste
electrical and electronic equipment (WEEE):
1 The symbol above indicates that separate collection of electrical and
electronic equipment is required.
2 When this product has reached the end of its serviceable life, it cannot be
disposed of as unsorted municipal waste. It must be collected and treated
separately.
3 It has been determined by the European Parliament that there are potential
negative effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment.
4 It is the users’ responsibility to utilize the available collection system to
ensure WEEE is properly treated.
For information about the available collection system, please contact
Extreme Customer Support at +353 61 705500 (Ireland).
Hazardous Substances
This product complies with the requirements of Directive 2011/65/EU of the
European Parliament and of the Council of 8 June 2011 on the restriction of the
use of certain hazardous substances in electrical and electronic equipment.
Declaration of Conformity in Languages of the European
Community
English Hereby, Extreme Networks, declares that this Radio
LAN device is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
Finnish Valmistaja Extreme Networks vakuuttaa täten että
Radio LAN device tyyppinen laite on direktiivin 1999/
5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen.
Dutch Hierbij verklaart Extreme Networks dat het toestel
Radio LAN device in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen
van richtlijn 1999/5/EG.
Bij deze verklaart Extreme Networks dat deze Radio
LAN device voldoet aan de essentiële eisen en aan de
overige relevante bepalingen van Richtlijn 1999/5/EC.
French Par la présente Extreme Networks déclare que
l'appareil Radio LAN device est conforme aux
exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE.
Par la présente, Extreme Networks déclare que ce
Radio LAN device est conforme aux exigences
essentielles et aux autres dispositions de la directive
1999/5/CE qui lui sont applicables.
Swedish Härmed intygar Extreme Networks att denna Radio
LAN device står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta
bestämmelser som framgår av direktiv 1999/5/EG.
Danish Undertegnede Extreme Networks erklærer herved, at
følgende udstyr Radio LAN device overholder de
væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
German Hiermit erklärt Extreme Networks die
Übereinstimmung des "WLAN Wireless Controller
bzw. Access Points" mit den grundlegenden
Anforderungen und den anderen relevanten
Festlegungen der Richtlinie 1999/5/EG.
Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Extreme Networks ∆ΗΛΩΝΕΙ
ΟΤΙ Radio LAN device ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ
ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ
ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ.
Icelandic Extreme Networks lysir her med yfir að thessi bunadur,
Radio LAN device, uppfyllir allar grunnkrofur, sem
gerdar eru i R&TTE tilskipun ESB nr 1999/5/EC.
Italian Con la presente Extreme Networks dichiara che
questo Radio LAN device è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite
dalla direttiva 1999/5/CE.
Spanish Por medio de la presente Extreme Networks declara
que el Radio LAN device cumple con los requisitos
esenciales y cualesquiera otras disposiciones
aplicables o exigibles de la Directiva 1999/5/CE.
Portuguese Extreme Networks declara que este Radio LAN device
está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Malti Hawnhekk, Extreme Networks, jiddikjara li dan Radio
LAN device jikkonforma mal-htigijiet essenzjali u ma
provvedimenti ohrajn relevanti li hemm fid-Dirrettiva
1999/5/EC.
P/N 9035184-03

Navigation menu