Ezurio AC4424-100 RF Transceiver Module User Manual AC4424
AeroComm Corporation RF Transceiver Module AC4424
Ezurio >
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 406055 |
| Application ID | qS+UVuDxANBWjPSX57M5wg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | Yes |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 20.8kB (259962 bits) |
| Date Submitted | 2004-03-16 00:00:00 |
| Date Available | 2004-03-15 00:00:00 |
| Creation Date | 2003-01-30 14:48:07 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2004-03-17 15:52:10 |
| Document Title | AC4424 |
| Document Creator | Microsoft Word 9.0 |
| Document Author: | N. Zach Hogya |
AC4424 2.4 GHz OEM TRANSCEIVERS Specifications Subject to Change User’s Manual Version 1.5 10981 EICHER DRIVE LENEXA, KS 66219 (800) 492492-2320 www.aerocomm.com wireless@aerocomm.com wireless@a erocomm.com DOCUMENT INFORMATION Copyright Information Copyright © 2002 AEROCOMM, Inc. All rights reserved. The information contained in this manual and the accompanying software programs are copyrighted and all rights are reserved by AEROCOMM, Inc. AEROCOMM, Inc. reserves the right to make periodic modifications of this product without obligation to notify any person or entity of such revision. Copying, duplicating, selling, or otherwise distributing any part of this product without the prior consent of an authorized representative of AEROCOMM, Inc. is prohibited. All brands and product names in this publication are registered trademarks or trademarks of their respective holders. This material is preliminary Information furnished by AEROCOMM in this specification is believed to be accurate. Devices sold by AEROCOMM are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. AEROCOMM makes no warranty, express, statutory, and implied or by description, regarding the information set forth herein. AEROCOMM reserves the right to change specifications at any time and without notice. AEROCOMM’s products are intended for use in normal commercial and industrial applications. Applications requiring unusual environmental requirements such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional testing for such application. 12/09/02 DOCUMENT INFORMATION Revision Description Version 1.0 Version 1.1 Version 1.2 Version 1.3 Version 1.4 Version 1.5 11/7/2001 – Initial Release Version 10/14/2002 – Not Released 10/18/2002 – Full release of AC4424 specification 11/19/2002 – Made Full-Duplex incompatible with Stream Mode 12/09/2002 – Changed Sub Hop Adjust setting recommendations 1/30/2003 – Removed all references to Commercial and Industrial temperature. All products are now Industrial temperature. Changed Section 4.2.1 EEPROM Byte Read to allow multiple byte reads. 12/09/02 FCC INFORMATION Agency Approval Approval Overview Part Number AC4424-10 AC4424-100 AC4424-200 US/FCC CAN/IC EUR/EN Portable Mobile X-32cm* X-32cm* Fixed X-32cm* X-32cm* * See RF Exposure warning on next page Note: The product approvals above are with antennas specified below. Agency Identification Numbers Part Number AC4424-10 AC4424-100 AC4424-200 US/FCC KQL-PKLR2400 KQL-PKLR2400-200 CAN/IC CAN2268391158A CAN2268391180A EUR/EN FCC Notice WARNING: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Labeling Requirements WARNING: The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate AeroComm FCC identifier for this product as well as the FCC Notice above. The FCC identifiers are listed above in the Agency Identifier Numbers section. Antenna Warning WARNING: This device has been tested with an MMCX connector with the antennas listed below. When integrated in the OEMs product, these fixed antennas require installation preventing end-users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 12/09/02 FCC INFORMATION 2 S191FL-5-RMM-2450S Type 1/4 Wave Dipole Gain (dBi) Nearson 5/8 Wave Dipole AC4424X AC4424X--200 Mfg. Nearson AC4424X AC4424X--100 Item Part Number 1 S131CL-5-RMM-2450S AC4424X AC4424X--10 Approved Antenna List MF MF PMF MF MF P=Portable, M=Mobile, F=Fixed/Basestation 12/09/02 FCC INFORMATION RF Exposure AC4424AC4424-10 WARNING: To comply with FCC RF Exposure requirements, the Original Equipment Manufacturer (OEM) must ensure that Antennas 3, 4, 5, 6 and 7 in the previous table must be installed and/or configured to operate with a separation distance of 20cm or more from all persons to satisfy RF Exposure compliance. The preceding statement must be included as a CAUTION statement in manuals for products operating with Antennas 3, 4, 5, 6 and 7 in the previous table to alert users on FCC RF Exposure compliance. RF Exposure AC4424AC4424-100 WARNING: To satisfy FCC RF exposure requirements for mobile and base station transmitting devices, a separation distance of 20cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operations at closer than this distance is not recommended. The preceding statement must be included as a CAUTION statement in manuals for OEM products to alert users on FCC RF Exposure compliance. RF Exposure AC4424AC4424-200 WARNING: To satisfy FCC RF exposure requirements for mobile and base station transmitting devices, a separation distance of 32cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operations at closer than this distance is not recommended. The preceding statement must be included as a CAUTION statement in manuals for OEM products to alert users on FCC RF Exposure compliance. 12/09/02 TABLE OF CONTENTS 1. OVERVIEW................................ OVERVIEW................................................................ ................................................................................................ ........................................................................................ ........................................................9 ........................9 2. AC4424 SPECIFICATIONS SPECIFICATIONS ................................................................ .............................................................................................. ..............................................................10 .............................. 10 3. SPECIFICATIONS ................................................................ ................................................................................................ ........................................................................... ...........................................11 ........... 11 3.1 INTERFACE SIGNAL DEFINITIONS .............................................................................................. 11 3.2 ELECTRICAL SPECIFICATIONS .................................................................................................. 12 3.3 SYSTEM TIMING...................................................................................................................... 12 3.3.1 Serial Interface Data Rate ............................................................................................ 12 3.3.2 Latency Times.............................................................................................................. 12 3.3.3 Maximum Overall System Throughput ........................................................................ 12 4. CONFIGURING THE AC44 AC4424 24 ................................................................ .......................................................................................... ..........................................................14 .......................... 14 4.1 EEPROM PARAMETERS ......................................................................................................... 14 4.2 EEPROM CONFIGURATION COMMANDS .................................................................................. 15 4.2.1 EEPROM Byte Read .................................................................................................... 16 4.2.2 EEPROM Byte Write..................................................................................................... 16 4.2.3 EEPROM Exit Configuration Command ...................................................................... 16 4.3 ON-THE-FLY CONTROL COMMAND REFERENCE......................................................................... 17 4.3.1 Status Request............................................................................................................. 17 4.3.2 Change Channel with Forced Acquisition Sync .......................................................... 17 4.3.3 Server/Client Command .............................................................................................. 18 4.3.4 Power-Down Command .............................................................................................. 18 4.3.5 Power-Down Wake-Up Command............................................................................... 19 4.3.6 Broadcast Mode .......................................................................................................... 19 4.3.7 Read Static Bank #1 Byte ........................................................................................... 19 4.3.8 Write Static Bank #1 Bytes .......................................................................................... 20 4.3.9 Read Static Bank #2 Bytes.......................................................................................... 20 4.3.10 Write Static Bank #2 Bytes .......................................................................................... 21 4.3.11 Write Destination Address ........................................................................................... 21 4.3.12 Read Destination Address ........................................................................................... 21 4.3.13 Temperature Update.................................................................................................... 22 5. THEORY OF OPERATION ................................................................ ............................................................................................... ...............................................................23 ............................... 23 5.1 HARDWARE INTERFACE ........................................................................................................... 23 5.1.1 TXD (Transmit Data) and RXD (Receive Data) (pins 2 and 3 respectively) ................. 23 5.1.2 Hop Frame (pin 6)........................................................................................................ 23 5.1.3 CTS Handshaking (pin 7) ............................................................................................ 23 5.1.4 RTS Handshaking (pin 8)............................................................................................. 23 5.1.5 9600 Baud/Packet Frame (pin 12) ............................................................................... 24 5.1.6 RSSI (pin 13)................................................................................................................ 24 5.1.7 Wr_Ena (EEPROM Write Enable) (pin 14) ................................................................... 25 5.1.8 UP_Reset (pin 15) ........................................................................................................ 25 5.1.9 Command/Data (pin 17) .............................................................................................. 25 5.1.10 In Range (pin 20) ......................................................................................................... 25 5.2 SOFTWARE PARAMETERS ........................................................................................................ 25 5.2.1 RF Architecture (Server-Client/Peer-to-Peer)............................................................... 25 5.2.2 RF Mode ...................................................................................................................... 26 5.2.3 Sub Hop Adjust............................................................................................................ 27 5.2.4 Duplex Mode................................................................................................................ 27 12/09/02 5.2.5 5.2.6 5.2.7 5.2.8 Interface Timeout/RF Packet Size................................................................................ 27 Serial Interface Baud Rate ........................................................................................... 28 Network Topology ....................................................................................................... 28 Auto Config .................................................................................................................. 29 6. APPLICATION APPLICATION EXAMPLES ................................................................ .............................................................................................. ..............................................................30 .............................. 30 7. DIMENSIONS................................ DIMENSIONS ................................................................ ................................................................................................ .................................................................................. ..................................................31 .................. 31 8. ORDERING INFORMATION ................................................................ ............................................................................................. .............................................................32 ............................. 32 8.1 8.2 PRODUCT PART NUMBERS ...................................................................................................... 32 DEVELOPER KIT PART NUMBERS .............................................................................................. 32 Figures Figure 1 – RSSI Voltage vs. Received Signal Strength.................................................................. 24 Figure 2 – AC4424 with MMCX ...................................................................................................... 31 Tables Table 1 – Pin Definitions................................................................................................................. 11 Table 2 – DC Input Voltage Characteristics ................................................................................... 12 Table 3 – DC Output Voltage Characteristics ................................................................................ 12 Table 4 – Maximum Overall System Throughputs......................................................................... 13 Table 5 – EEPROM Parameters ..................................................................................................... 14 Table 6 – Static Memory Address Map .......................................................................................... 17 Table 7 – Sub Hop Adjust Settings ................................................................................................ 27 Table 8 – Baud Rate....................................................................................................................... 28 Table 9 – US and International RF Channel Number Settings ...................................................... 29 Table 10 – Auto Config Parameters ............................................................................................... 29 12/09/02 AC4424 Specifications AC4424 Features Simple 5V TTL level serial interface for fast integration Frequency Hopping Spread Spectrum for security and interference rejection Cost Efficient for high volume applications Low power consumption for battery powered implementations Small size for portable and enclosed applications Very Low latency and high throughput Industrial temperature (-40°C to 80°C) 1. Overview The AC4424 is a member of AeroComm’s ConnexRF OEM transceiver family. It is designed for integration into OEM systems operating under FCC part 15.247 regulations for the 2.4 GHz ISM band. The AC4424 is a cost-effective, High performance, 2.4 GHz frequency hopping spread spectrum transceiver. It provides an asynchronous TTL level serial interface for OEM Host communications. Communications include both system and configuration data. The Host supplies system data for transmission to other Host(s). Configuration data is stored in an on-board EEPROM. All frequency hopping, synchronization, and RF system data transmission/reception is performed by the transceiver. The AC4424 transceivers can be used as a direct serial cable replacement – requiring no special Host software for operation. They also feature a number of On-the-Fly Control Commands providing the OEM Host with a very versatile interface for any situation. AC4424 transceivers operate in a Point-to-Point or Point-to-Multipoint, Client-Server or Peer-to-Peer architecture. One transceiver is configured as a Server and there can be one or many Clients. To establish synchronization between transceivers, the Server emits a beacon. Upon detecting a beacon, a Client transceiver informs its Host and a RF link is established. There are two data rates the OEM should be aware of: • Serial Interface Data Rate – All transceivers can be configured to common PC serial port baud rates from 110 bps to 288,000 bps. • Effective Data Transmission Rate – The AC4424 is a highly efficient, low-latency transceiver. This document contains information about the hardware and software interface between an AeroComm AC4424 transceiver and an OEM Host. Information includes the theory of operation, specifications, interface definition, configuration information and mechanical drawing. The OEM is responsible for ensuring the final product meets all FCC and/or appropriate regulatory agency requirements listed herein before selling any product. 12/09/02 AC4424 Specifications 2. AC4424 Specifications Specifications GENERAL Interface Serial Interface Data Rate Power Consumption (typical) Channels (used to create independent networks) Security 20 pin mini-connector PC baud rates from 110 bps to 288,000 bps Duty Cycle (TX=Transmit; RX=Receive) 10%TX 50%TX 100%TX 100%RX AC4424-10: 90mA 115mA 140mA 85mA AC4424-100: 100mA 160mA 235mA 85mA AC4424-200: 115mA 235mA 385mA 85mA 4 channel sets consisting of 16 channels each One byte System ID PwrPwr-Down 15mA 15mA 15mA RADIO Frequency Band Radio Type Output Power (conducted, no antenna) Effective Isotropic Radiated Power (EIRP with 3dBi gain antenna) Voltage Sensitivity Range (based on 3dBi gain antenna) US/Canada: 2.402 – 2.478 GHz France: 2.448 – 2.457 GHz Frequency Hopping Spread Spectrum AC4424-10, 10mW typical AC4424-100, 50mW typical AC4424-200, 200mW typical AC4424-10, 20mW typical AC4424-100, 100mW typical AC4424-200, 400mW typical 5V nominal ±2%, ±50mV ripple -90dBm typical AC4424-10, Indoors to 300 ft., Outdoors to 3000 ft. AC4424-100, Indoors to 400 ft., Outdoors to 6000 ft. AC4424-200, Indoors to 500 ft., Outdoors to 10000 ft. ENVIRONMENTAL Temperature (Operating) Industrial: Temperature (Storage) Humidity (non-condensing) AC4424: -40°C to 80°C -50°C to +85°C 10% to 90% PHYSICAL Dimensions Antenna Weight 12/09/02 1.65” x 2.65” x 0.20” AC4424-10, MMCX Jack AC4424-100, MMCX Jack AC4424-200, MMCX Jack Less than 0.75 ounce 10 AC4424 Specifications 3. Specifications 3.1 INTERFACE SIGNAL DEFINITIONS The AC4424 has a simple interface that allows OEM Host communications with the transceiver. Table 1 – Pin Definitions, Definitions shows the connector pin numbers and associated functions. The I/O direction is with regard to the transceiver. All I/O is 5VDC TTL level signals except for RSSI. All inputs are weakly pulled High and may be left floating during normal operation. Table 1 – Pin Definitions Pin Type Signal Name Function NC No Connect TXD Transmitted data out of the transceiver RXD Data input to the transceiver NC GND GND Hop Frame CTS RTS No Connect Signal Ground HOP FRAME – Active Low when the transceiver is hopping. Clear to Send – Active Low when the transceiver is ready to accept data for transmission. Request to Send – When enabled in EEPROM, active Low when the OEM Host is ready to accept data from the transceiver. NOTE: Keeping RTS High for too long can cause data loss. NC No Connect VCC 5V ± 2%, ± 50mV ripple 10 PWR 11 PWR VCC 12 I/O 9600_BAUD/ 9600_BAUD – When pulled logic Low before applying power or resetting the transceiver’s Packet Frame serial interface is forced to a 9600, 8, N, 1 rate. To exit, transceiver must be reset or power- 5V ± 2%, ±50 mV ripple cycled with 9600_Baud logic High. Packet Frame – When programmed in EEPROM, Packet Frame will transition logic Low at the start of a received RF packet and transition logic High at the completion of the packet. 13 RSSI Received Signal Strength - An analog output giving a relative indication of received signal strength while in Receive Mode 14 WR_ENA EEPROM Write Enable – When pulled logic Low, it allows the Host to write the on-board 15 UP_RESET RESET – Controlled by the AC4424 for power-on reset if left unconnected. After a Stable EEPROM. Resetting the transceiver with this pin pulled Low may corrupt EEPROM data. power-on (50ms) a 50us logic High pulse will reset the AC4424. Do not power-up the transceiver with this pin tied Low. 16 GND GND 17 Command/Data Signal Ground When logic Low, transceiver interprets Host data as command data. When logic High, transceiver interprets Host data as transmit data. 18 NC 19 20 NC IN_RANGE No Connect No Connect In Range – Active Low when a Client radio is in range of a Server on same Channel with the same System ID. I = Input to the transceiver 12/09/02 O = Output from the transceiver 11 AC4424 Specifications 3.2 ELECTRICAL SPECIFICATIONS Table 2 – DC Input Voltage Characteristics Pin 12 14 15 17 Type Name RXD RTS 9600_Baud WR_ENA UP_RESET Command/Data High Min. 0.2Vcc+0.9 0.2Vcc+0.9 0.2Vcc+0.9 0.7Vcc 0.7Vcc 0.2Vcc+0.9 High Max. Vcc+0.5 Vcc+0.5 Vcc+0.5 Vcc+1 Vcc+0.5 Vcc+0.5 Low Min. -0.5 -0.5 -0.5 -0.3 -0.5 -0.5 Low Max. 0.2Vcc-0.1 0.2Vcc-0.1 0.2Vcc-0.1 0.5 0.2Vcc-0.1 0.2Vcc-0.1 Unit Table 3 – DC Output Voltage Voltage Characteristics Pin 12 13 20 Type Name TXD Hop Frame CTS Packet Frame RSSI IN_RANGE High Min. Vcc-0.7 @ -30µA Vcc-0.7 @ -30µA Vcc-0.7 @ -30µA Vcc-0.7 @ -30µA See Figure 1 Vcc-0.7 @ -30µA Low Max. 0.4 @ 1.6mA 0.4 @ 1.6mA 0.4 @ 1.6mA 0.4 @ 1.6mA See Figure 1 0.4 @ 1.6mA Unit 3.3 SYSTEM TIMING Care should be taken when selecting transceiver architecture as it can have serious effects on data rates, latency timings, and Overall System Throughput. The importance of these three characteristics will vary from system to system and should be a strong consideration when designing the system. 3.3.1 Serial Interface Data Rate The Serial Interface Data Rate is programmable by the Host. This is the rate the Host and transceiver communicate over the serial bus. Possible values range from 110 bps to 288,000 bps. The only supported mode is asynchronous – 8-bit, No Parity, 1 Start Bit, and 1 Stop Bit. 3.3.2 Latency Times TBD 3.3.3 Maximum Overall System Throughput When configured as shown in the table below, an AC4424 transceiver is capable of achieving the listed throughput. However, in the presence of interference or at longer ranges, the transceiver may not be able to meet these specified throughputs. Note: Higher overall system throughputs are possible. possible. Contact technical support for details. 12/09/02 12 AC4424 Specifications Table 4 – Maximum Overall System Throughputs RF Mode Interface Baud Rate Duplex FEC Direction Throughput (bps) Stream 192k Half Disabled One way 192k Stream 192k Half Enabled One way 64k Acknowledge 115,200 Half Disabled One way 80k Acknowledge 115,200 Full Disabled Both ways 40k 12/09/02 13 AC4424 Specifications 4. Configuring the AC4424 4.1 EEPROM PARAMETERS A Host can program various parameters that are stored in EEPROM and become active after a poweron reset. Table 5 - EEPROM Parameters, Parameters gives the locations and descriptions of the parameters that can be read or written by a Host. Factory default values are also shown. Do not write to any EEPROM addresses other than those listed below. Do not copy a transceiver’s transceiver’s EEPROM data to another transceiver. Doing so may cause the transceiver to malfunction. Table 5 – EEPROM Parameters Parameter EEPROM Length Address (Bytes) Product ID 00H 40 Sub Hop Adjust 36H 40H 41H 42H 43H 45H Channel Number Server/Client Mode Baud Rate Low Baud Rate High Control 0 12/09/02 Range Default Description 40 bytes - Product identifier string. Includes revision information for software and hardware. D0h = Acknowledge 80h, D0h D0h 80h = Stream Set 0 = 00 – 0Fh (US/Canada) Set 1 = 10 – 1Fh (US/Canada) Set 2 = 20 – 2Fh (US/Canada) 00 – 3Fh 00h Set 3 = 30 – 3Fh (France) 01h = Server 02h = Client 01 – 02h 02h 00 – FFh 05h Low Byte of the interface baud rate. 00 – FFh 00h High Byte of the interface baud rate. 00010100b Settings are: (14h) Bit 7 – AeroComm Use Only Bit 6 – AeroComm Use Only Bit 5 – Sync to Channel 0 = Don't Sync to Channel 1 = Sync to Channel Bit 4 – AeroComm Use Only Bit 3 – Packet Frame 0 = Disable Packet Frame 1 = Use pin 12 as Packet Frame Bit 2 – RF Mode 0 = RF Stream Mode 1 = RF Acknowledge Mode Bit 1 – RF Delivery 0 = Addressed 1 = Broadcast Bit 0 – FEC 0 = No Forward Error Correction 1 = Use Forward Error Correction 14 AC4424 Specifications Parameter Frequency Offset Transmit Retries Broadcast Attempts API Control Interface Timeout Sync Channel RF Packet Size CTS On CTS On Hysteresis Destination ID System ID MAC ID EEPROM Length Address (Bytes) Range Default 46H 00h, 2Eh 00h 4CH 01 - FFh 10h 4DH 56H 01 – FFh 58H 5AH 5BH 5CH 01 – FFh 00 – 3Fh 01 – 40h 01 – FFh F0h 01h 40h C0h 5DH 70H 76H 80H 01 – FFh 80h 6 Bytes 01h 6 Bytes 00 – FFh Description Channel Set 0 = N/A Channel Set 1 = 00h Channel Set 2 = 00h Channel Set 3 = 2Eh 04h 01000011b Settings are: = 43h Bit 7 – AeroComm AeroComm Use Only Bit 6 – RF Architecture 0 = Server-Client 1 = Peer-to-Peer Bit 5 – AeroComm Use Only Bit 4 – AeroComm Use Only Bit 3 – AeroComm Use Only Bit 2 – RTS Enable 0 = RTS Ignored 1 = Transceiver obeys RTS Bit 1 – Duplex Mode 0 = Half Duplex 1 = Full Duplex Bit 0 – Auto Config 0 = Use EEPROM values 1 = Auto Configure Values Unique IEEE MAC Address 4.2 EEPROM CONFIGURATION COMMANDS The configuration set allows the Host to modify the operation of the transceiver. If the Command/Data pin (Pin 17) is pulled logic Low, a transceiver will interpret incoming Host data as Command Data. The Host can then read and write parameters using the various configuration commands listed below. To exit Configuration Mode, the Host must perform a hardware or power-on reset or issue an Exit Command Mode command to the transceiver. 12/09/02 15 AC4424 Specifications 4.2.1 EEPROM Byte Read Upon receiving this command, a transceiver will transmit the desired data from the address requested by the Host. Host Command: Byte 1 = C0h Byte 2 = Address Byte 3 = Length (01…FFh = 1…255 bytes; 00h = 256 bytes) Transceiver Response: Byte 1 = C0h Byte 2 = Address Byte 3 = Length Byte 4…n = Data at requested address(s) 4.2.2 EEPROM Byte Write Upon receiving this command, a transceiver will write the data byte to the address specified but will not echo it back to the Host until the EEPROM write cycle is complete. The write can take as long as 10ms to complete. Following the write cycle, a transceiver will transmit the data byte to the Host. The WR_ENA pin (Pin 14) must be pulled logic Low to enable the write prior to issuing this command or the write will not occur, requiring the transceiver to be reset. The length byte must be set to 01h. Only single byte writes are allowed. Host Command: Byte 1 = C1h Byte 2 = Address Byte 3 = 01h Byte 3 = Data to store at Address Transceiver Response: Byte 1 = C1h Byte 2 = Address Byte 3 = 01h Byte 4 = Data to store at Address Note: The WR_ENA pin on the connector should only be pulled logic Low before sending an EEPROM Byte Write Write command and must be held logic Low until the data byte is echoed to the Host. 4.2.3 EEPROM Exit Configuration Command The OEM Host can cause the transceiver to exit command mode by issuing the Exit Configuration Command mode command to the transceiver. However, However, the transceiver will not reflect any of the changes programmed into the EEPROM until the transceiver is reset. Host Command: Byte 1 = 56h Transceiver Response: Byte 1 = 56h 12/09/02 16 AC4424 Specifications 4.3 ON-THE-FLY CONTROL COMMAND REFERENCE The AC4424 transceiver contains static memory that holds many of the parameters that control the transceiver operation. Using the “CC” command set allows many of these parameters to be changed during system operation. Because the memory these commands affect is static, when the transceiver is reset, these parameters will revert back to the settings stored in the EEPROM. Do not to modify undocumented static addresses as undesired operation may occur. All “CC” commands must be issued from the Host to the transceiver with Command/Data (Pin 17) pulled logic Low. To exit “CC” mode, simply take the Command/Data pin High. Table 6 – Static Memory Address Map Static Bank # Address Description 67h – 69h Lower 3 bytes of Destination Address 4.3.1 Status Request The Host issues this command to request the status of the transceiver. Host Command: Byte 1 = CCh Byte 2 = 00h Byte 3 = 00h Transceiver Response: Byte 1 = CCh Byte 2 = Firmware version number Byte 3 = Data1 Where: Data1 = 00 for Server in Normal Operation 01 for Client in Normal Operation 02 for Server in Acquisition Sync 03 for Client in Acquisition Sync 4.3.2 Change Channel with Forced Acquisition Sync The Host issues this command to change the channel of the transceiver and force the transceiver to actively begin synchronization. Host Command: Byte 1 = CCh Byte 2 = 02h Byte 3 = RF Channel Number (Hexadecimal) Transceiver Response: Byte 1 = CCh Byte 2 = RF Channel Number (Hexadecimal) 12/09/02 17 AC4424 Specifications 4.3.3 Server/Client Command The Host issues this command to change the mode (Server or Client) of the transceiver and can force the transceiver to actively begin synchronization. Host Command: Byte 1 = CCh Byte 2 = 03h Byte 3 = Data1 Where: Data1 = 00 for Server in Normal Operation 01 for Client in Normal Operation 02 for Server in Acquisition Sync 03 for Client in Acquisition Sync Transceiver Response: Byte 1 = CCh Byte 2 = Software Version Number Byte 3 = Data1 Where: Data1 = Data1 from Host Command 4.3.4 PowerPower-Down Command After the Host issues the power-down command to the transceiver, the transceiver will de-assert the In_Range line after entering power-down. A Client transceiver in power-down will remain in sync with a Server for a minimum of 2 minutes. To maintain synchronization with the Server, this Client transceiver should re-sync to the Server at least once every 2 minutes. This re-sync is accomplished by issuing the PowerPower-Down WakeWake-Up Command and waiting for the In Range line to go active. Once this occurs, the Client transceiver is in sync with the Server and can be put back into power-down. Host Command: Byte 1 = CCh Byte 2 = 06h Transceiver Response: Byte 1 = CCh Byte 2 = 00h 12/09/02 18 AC4424 Specifications 4.3.5 PowerPower-Down WakeWake-Up Command The Power-Down Wake-Up Command is issued by the Host to bring the transceiver out of powerdown mode. Host Command: Byte 1 = CCh Byte 2 = 07h Transceiver Response: Byte 1 = CCh Byte 2 = 00h 4.3.6 Broadcast Mode The Host issues this command to change the transceiver operation between Addressed Mode and Mode. If addressed mode is selected the transceiver will send all packets to the radio Broadcast Mode designated by the Destination Address programmed in the transceiver. Host Command: Byte 1 = CCh Byte 2 = 08h Byte 3 = 00 for addressed mode, 01 for broadcast mode Transceiver Response: Byte 1 = CCh Byte 2 = 00 for addressed mode, 01 for broadcast mode 4.3.7 Read Read Static Bank #1 Byte The OEM Host issues this command to the transceiver to read Static Bank #1 Bytes. Static Bank #1 is a bank of memory that holds many of the parameters that control the radio. Using the Read/Write Static Bank #1 command allows these parameters to be changed dynamically. Because the memory bank is static, when the radio is reset, these parameters will revert back to the settings stored in EEPROM. Be careful not to change undocumented Static Bank addresses as undesired operation may occur. Host Command: Byte 1 = CCh Byte 2 = 0Ah Byte 3 = 00 – FFh corresponding to a valid Static Bank #1 address Transceiver Response: Byte 1 = CCh Byte 2 = 00 – FFh corresponding to a valid Static Bank #1 address 12/09/02 19 AC4424 Specifications 4.3.8 Write Static Bank #1 Bytes The Host issues this command to the transceiver to write Static Bank #1 Bytes. Static Bank #1 is a bank of memory that holds many of the parameters that control the radio. Using the Read/Write Static Bank #1 command allows these parameters to be changed dynamically. Because the memory bank is static, when the radio is reset, these parameters will revert back to the settings stored in EEPROM. Be careful not to change undocumented Static Bank addresses as undesired operation may occur. Host Command: Byte 1 = CCh Byte 2 = 0Bh Byte 3 = 00 – FFh corresponding to a valid Static Bank #1 address Byte 4 = 00 – FFh corresponding to new value for address specified by Byte 3 Transceiver Response: Byte 1 = CCh Byte 2 = 00 – FFh corresponding to a valid Static Bank #1 address Byte 3 = 00 – FFh corresponding to new value for address specified by Byte 2 4.3.9 Read Static Bank #2 Bytes The Host issues this command to the transceiver to read Static Bank #2 Bytes. Static Bank #2 is a bank of memory that holds many of the parameters that control the radio. Using the Read/Write Static Bank #2 command allows these parameters to be changed dynamically. Because the memory bank is static, when the radio is reset, these parameters will revert back to the settings stored in EEPROM. Be careful not to change undocumented Static Bank addresses as undesired operation may occur. Host Command: Byte 1 = CCh Byte 2 = 0Ch Byte 3 = 00 – FFh corresponding to a valid Static Bank #2 address Transceiver Response: Byte 1 = CCh Byte 2 = 00 – FFh corresponding to a valid Static Bank #2 address 12/09/02 20 AC4424 Specifications 4.3.10 Write Static Bank #2 Bytes The Host issues this command to the transceiver to write Static Bank #2 Bytes. Static Bank #2 is a bank of memory that holds many of the parameters that control the radio. Using the Read/Write Static Bank #2 command allows these parameters to be changed dynamically. Because the memory bank is static, when the radio is reset, these parameters will revert back to the settings stored in EEPROM. Be careful not to change undocumented Static Bank addresses as undesired operation may occur. Host Command: Byte 1 = CCh Byte 2 = 0Dh Byte 3 = 00 – FFh corresponding to a valid Static Bank #2 address Byte 4 = 00 – FFh corresponding to new value for address specified by Byte 3 Transceiver Response: Byte 1 = CCh Byte 2 = 00 – FFh corresponding to a valid Static Bank #2 address Byte 3 = 00 – FFh corresponding to new value for address specified by Byte 2 4.3.11 Write Destination Address The Host issues this command to the transceiver to change the Destination Address. This is a very powerful command that provides the OEM Host with a means for ad-hoc networking. Only the three Least Significant Bytes of the MAC Address are used for packet delivery. Host Command: Byte 1 = CCh Byte 2 = 10h Bytes 3 – 5 = 00 – FFh corresponding the three LSB’s of the destination MAC Address Transceiver Response: Byte 1 = CCh Bytes 2 – 4= 00 – FFh corresponding the three LSB’s of the destination MAC Address 4.3.12 Read Destination Address The Host issues this command to the transceiver to read the Destination Address. This is a very powerful command that provides the OEM Host with a means for ad-hoc networking. Only the three Least Significant Bytes of the MAC Address are used for packet delivery. Host Command: Byte 1 = CCh Byte 2 = 11h Transceiver Transceiver Response: Byte 1 = CCh Bytes 2 – 4= 00 – FFh corresponding the three LSB’s of the destination MAC Address 12/09/02 21 AC4424 Specifications 4.3.13 Temperature Update The Host issues this command to update the transceiver with the ambient temperature. This command is only valid on AC4424 family transceivers not already fitted with a temperature sensor. Host Command: Byte 1 = CCh Byte 2 = A3h Byte 3 = D8h – 50h (corresponding to the ambient temperature in °C) Transceiver Response: Byte 1 = CCh Byte 2 = D8h – 50h (corresponding to the ambient temperature in °C) 12/09/02 22 AC4424 Specifications 5. Theory of Operation 5.1 HARDWARE INTERFACE Below is a description of all hardware pins used to control the AC4424. 5.1.1 TXD (Transmit Data) and RXD (Receive Data) (pins 2 and 3 respectively) The AC4424 accepts 5V TTL level asynchronous serial data in the RXD pin and interprets that data as either Command Data or Transmit Data. Data is sent from the transceiver to the OEM Host via the TXD pin. The data must be of the format 8-N-1 (8 data bits, No Parity bits, One stop bit). 5.1.2 Hop Frame (pin 6) The AC4424 is a frequency hopping spread spectrum radio. Frequency hopping allows the system to hop around interference in order to provide a better wireless link. Hop Frame transitions logic Low at the start of a hop and transitions logic High at the completion of a hop. The OEM Host is not required to monitor Hop Frame. 5.1.3 CTS Handshaking (pin 7) The AC4424 has an interface buffer size of 256 bytes. If the buffer fills up and more bytes are sent to the transceiver before the buffer can be emptied, data corruption will occur. The transceiver prevents this corruption by asserting CTS High as the buffer fills up and taking CTS Low as the buffer is emptied. CTS On in conjunction with CTS On Hysteresis control the operation of CTS. CTS On specifies the amount of bytes that must be in the buffer for CTS to be disabled (High). Even while CTS is disabled, the OEM Host can still send data to the transceiver, but it should do so carefully. Once CTS is disabled, it will remain disabled until the buffer is reduced to the size specified by CTS On Hysteresis. The following equation should always be used for setting CTS On, CTS On Hysteresis and RF Packet Size: Size CTS On – CTS On Hysteresis = RF Packet Size 5.1.4 RTS Handshaking (pin 8) With RTS Mode disabled, the transceiver will send any received packet to the OEM Host as soon as the packet is received. However, some OEM Hosts are not able to accept data from the transceiver all of the time. With RTS Mode Enabled, the OEM Host can keep the transceiver from sending it a packet by disabling RTS (logic High). Once RTS is enabled (logic Low), the transceiver can send packets to the OEM Host as they are received. Note: Leaving RTS disabled for too long can cause data loss once the transceiver’s receive buffer fills up. 12/09/02 23 AC4424 Specifications 5.1.5 9600 Baud/Packet Baud/Packet Frame (pin 12) 9600_BAUD – When pulled logic Low before applying power or resetting, the transceiver’s serial interface is forced to a 9600, 8-N-1 (8 data bits, No parity, 1 stop bit) rate. To exit, transceiver must be reset or power-cycled with 9600_Baud logic High. Packet Frame – When enabled in EEPROM, Packet Frame will transition logic Low at the start of a received RF packet and transition logic High at the completion of the packet. 5.1.6 RSSI (pin 13) Received Signal Strength Indicator is used by the Host as an indication of instantaneous signal strength at the receiver. The Host must calibrate RSSI without a RF signal being presented to the receiver. Calibration is accomplished by following the steps listed below to find a minimum and maximum voltage value. 1) Power up only one Client (no Server) transceiver in the coverage area. 2) Measure the RSSI signal to obtain the minimum value with no other signal present. 3) Power up a Server. Make sure the two transceivers are in close proximity and measure the Client’s peak RSSI once the Client reports In Range to obtain a maximum value at full signal strength. Figure 1 shows approximate RSSI performance. Output is 1.20V to 4.50V. Figure 1 – RSSI Voltage vs. Received Signal Strength -10 Signal at Receiver (dBm) -20 -30 -40 -50 -60 -70 -80 -90 -100 1.2 1.3 1.57 2.3 3.8 4.5 Voltage (VDC) 12/09/02 24 AC4424 Specifications 5.1.7 Wr_Ena Wr_Ena (EEPROM Write Enable) (pin 14) Wr_Ena is a direct connection to the Write Enable line on the EEPROM. When logic Low, the EEPROM’s contents may be changed. When logic High, the EEPROM is protected from accidental and intentional modification. It is recommended that this line only be Low when an EEPROM write is desired to prevent unintentional corruption of the EEPROM. 5.1.8 UP_Reset (pin 15) UP_Reset provides a direct connection to the reset pin on the AC4424 microprocessor. To guarantee a valid power-up reset, this pin should never be tied Low on power-up. For a valid power-on reset, reset must be High for a minimum of 50us. 5.1.9 Command/Data (pin 17) When logic High, transceiver interprets Host data as transmit data to be sent to other transceivers and their Hosts. When logic Low, transceiver interprets Host data as command data (see section 4). 4) 5.1.10 In Range (pin 20) The IN_RANGE pin at the connector will be driven logic Low when a Client is in range of a Server on the same RF Channel and System ID ID. If a Client cannot hear a Server for 5s, it will drive the IN_RANGE pin logic High and enter a search mode looking for a Server. As soon as it detects a Server, the IN_RANGE pin will be driven logic Low. A Server Host can determine which Clients are in range by the Server’s Host software polling a Client’s Host. 5.2 SOFTWARE PARAMETERS Below is a description of all software parameters used to control the AC4424. 5.2.1 RF Architecture (Server(Server-Client/PeerClient/Peer-toto-Peer) The Server controls the system timing by sending out regular beacons (transparent to the transceiver Host) which contain system timing information. This timing information synchronizes the Client radios to the Server. Each network should consist of only one Server. There should never be two Servers on the same RF Channel nel Number in the same coverage area, as the interference between the two Servers will severely Chan hinder RF communications. In Server-Client architecture, the Server communicates with the Clients and the Clients only communicate with the Server. Enabling Peer Peerer-toto-Peer Mode will allow all radios on the network to communicate with each other. Note: All transceivers on the same network must have the same setting for PeerPeer-toto-Peer and there must still be one, and only one, Server present in a PeerPeer-toto-Peer network. network. 12/09/02 25 AC4424 Specifications 5.2.2 RF Mode All radios located on the same network must use the same RF Mode. Acknowledge Mode In Addressed Acknowledge Mode, the RF packet is sent out to the receiver designated by the Destination Address. Address Transmit Retries is used to increase the odds of successful delivery to the intended receiver. Transparent to the OEM Host, the sending transceiver will send the RF packet to the intended receiver. If the receiver receives the packet free of errors, it will tell the sender. If the sender does not receive this acknowledge, it will assume the packet was never received and retry the packet. This will go on until the packet is successfully received or the transmitter exhausts all of its retries. The received packet will only be sent to the OEM Host if and when it is received free of errors. In Broadcast Acknowledge Mode, the RF packet is broadcast out to all eligible receivers on the network. In order to increase the odds of successful delivery, Broadcast Attempts is used to increase the odds of successful delivery to the intended receiver(s). Transparent to the OEM Host, the sending transceiver will send the RF packet to the intended receiver. If the receiver detects a packet error, it will throw out the packet. This will go on until the packet is successfully received or the transmitter exhausts all of its attempts. Once the receiver successfully receives the packet it will send the packet to the OEM Host. It will throw out any duplicates caused by further Broadcast Attempts. The received packet will only be sent to the OEM Host if it is received free of errors. Stream Mode In Broadcast Stream mode, the RF packet is broadcast out to all eligible receivers on the network. In Addressed Stream Mode, the RF packet is sent out to the receiver designated by the Destination Address. Address The sending transceiver will send each RF packet out once. There are no retries on the packet. Whether or not the packet contains errors, the receiver(s) will send the packet to the OEM Host. However, if receiver is not able to receive the packet in its entirety (there are bytes missing), it will not send the packet to the OEM Host. In order to increase the odds of successful delivery, Forward Error Correction (FEC) may be used. FEC is used (transparent to the OEM Host) to increase the odds of correctly receiving a packet sent over the RF. When enabled, the transceiver will send every byte over the RF 3 times and then perform a best-of-three bit-wise decision on the received bytes. Enabling FEC can cut overall throughput by 1/3. Note: All transceivers on the same network must have the same setting for FEC. Stream Mode is incompatible with Full Duplex Mode. 12/09/02 26 AC4424 Specifications 5.2.3 Sub Hop Adjust Sub Hop Adjust is an AC4424 protocol parameter and its settings are as follows: Table 7 – Sub Hop Adjust Settings RF Mode Sub Hop Adjust Acknowledge D0h Stream 80h 5.2.4 Duplex Mode In Half Duplex mode, the AC4424 will send a packet out over the RF when it can. This can cause packets sent at the same time by a Server and a Client to collide with each other over the RF. To prevent this, Full Duplex Mode can be enabled. This mode restricts Clients to transmitting on odd numbered frequency “bins” and the Server to transmitting on even frequency bins. Though the RF hardware is still technically half duplex, it makes the radio seem full duplex. This can cause overall throughputs to be cut in half. Note: All transceivers on the same network must have the same setting for Full Duplex. Full Duplex mode is incompatible with Stre Stream am RF mode. 5.2.5 Interface Timeout/RF Packet Size Interface timeout, in conjunction with RF Packet Size, Size determines when a buffer of data will be sent out over the RF as a complete RF packet based on whichever condition occurs first. Interface Timeout – Interface Timeout specifies a maximum byte gap in between consecutive bytes. When that byte gap is exceeded, the bytes in the transmit buffer are sent out over the RF as a complete packet. Interface timeout is adjustable in 160uS decrements. The actual timeout created by Interface Timeout is equal to the 2's complement of Interface Timeout times 160uS. The default value for Interface Timeout is F0H or 2.56ms. RF Packet Size – When the amount of bytes in the transceiver transmit buffer equals RF Packet Size, those bytes are sent out as a complete RF packet. 12/09/02 27 AC4424 Specifications 5.2.6 Serial Interface Baud Rate This two-byte value determines the baud rate used for communicating over the serial interface to a transceiver. Table 5 - Baud Rate/Timeout lists values for some common baud rates. Baud rates below 110 baud are not supported. For a baud rate to be valid, the calculated baud rate must be within ±3% of the OEM Host baud rate. If the 9600_BAUD pin (Pin 12) is pulled logic Low at reset, the baud rate will be forced to 9,600. 9,600. For Baud Rate values other than those shown in Table 5 - Baud Rate, Rate the following equation can be used: BAUD = (18.432E+06/(32*desired baud rate)) BaudH= High 8 bits of BAUD (base16) BaudL = Low 8 bits of BAUD (base16) Table 8 – Baud Ra Rate te Baud Rate 288,000 192,000 115,200 57,600 38,400 28,800 19,200 14,400 9,600 4800 2400 1200 300 110 BaudL (42h) 02h 03h 05h 0Ah 0Fh 14h 1Eh 28h 3Ch 78h F0h E0h 80h 74h BaudH (43h) 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 01h 07h 14h Minimum Interface Timeout (58h) FFh FFh FEh FDh FCh FBh F9h F7h F2h E5h CBh 97h 01h 01h 5.2.7 Network Topology RF Channel Number – RF Channel Number provides a physical separation between co-located networks. The AC4424 is a spread spectrum frequency hopping radio with a fixed hopping sequence. Without synchronizing the different networks to each other, different channel numbers could possibly interfere with each other and create “cross-talk.” To avoid cross-talk interference, co-located networks should use SyncSync-to-Channel. Channel A Server radio with Sync-to-Channel enabled will synchronize its frequency hop timing to a system located on the RF Channel specified by Sync Channel Channel. The only requirement is that Sync Channel be numerically less than RF Channel. Therefore, every co-located network will be synchronizing to the network with the lowest RF Channel. Four Channel sets are provided for the AC4424. Frequency Offset is a protocol parameter used to satisfy unique international requirements. CoCo-located networks must use use the same Channel Set. 12/09/02 28 AC4424 Specifications Table 9 – US and International RF Channel Number Settings Channel Set RF Channel Number Range Frequency Offset (40h) (46h) Countries 00h – 0Fh N/A US,Canada 10h – 1Fh US,Canada 20h – 2Fh US,Canada 30h – 3Fh 2Eh France System ID – System ID is similar to a password character or network number and makes network eavesdropping more difficult. A receiving radio will not go in range of or communicate with another radio on a different System ID. 5.2.8 Auto Config The AC4424 has several variables that control its RF performance and vary by RF Mode and RF Architecture. Architecture Enabling Auto Config will bypass the value for these variables stored in EEPROM and use predetermined values for the given Interface Baud Rate. Auto Config has been optimized for 192,000 baud Stream Mode, 115,200 baud Acknowledge Mode and all lower baud rates. It should only be disabled with recommendation from AeroComm. Below is a list containing some of the variables affected by Auto Config and their respective values: Table 10 – Auto Config Parameters 12/09/02 Parameter Auto Config Value RF Packet Size 40h CTS On C0h CTS On Hysteresis 80h 29 AC4424 Specifications 6. Application Examples TBD 12/09/02 30 AC4424 Specifications 7. Dimensions All AC4424 products measure 1.65”W x 2.65”L. Critical parameters are as follows: • J1 – 20 pin OEM interface connector (Samtec TMM-110-01-L-D-SM, mates with Samtec SMM-110-02-S-D) • MMCX Jack – Antenna connector (Telegartner P/N J01341C0081) mates with any manufacturer’s MMCX plug Figure 2 – AC4424 with 12/09/02 31 Ordering Information 8. Ordering Information 8.1 PRODUCT PART NUMBERS AC4424AC4424-10: 10 AC4424 with 10mW output power, interface data rates to 288Kbps, MMCX antenna connector, -40°C to 80°C AC4424AC4424-100: 100 AC4424 with 50mW output power, interface data rates to 288Kbps, MMCX antenna connector, -40°C to 80°C AC4424AC4424-200: 200 AC4424 with 200mW output power, interface data rates to 288Kbps, MMCX antenna connector, -40°C to 80°C 8.2 DEVELOPER KIT PART NUMBERS SDKSDK-4424I4424I-10: 10 Includes (2) AC4424-10 transceivers, (2) RS232 Serial Adapter Boards, (2) 6Vdc unregulated power supplies, (2) Serial cables, (2) S151FL-5-RMM-2450S dipole antennas with 5” pigtail and MMCX connector, configuration/testing software, Integration engineering support SDKSDK-4424I4424I-100: 100 Includes (2) AC4424-100 transceivers, (2) RS232 Serial Adapter Boards, (2) 6Vdc unregulated power supplies, (2) Serial cables, (2) S151FL-5-RMM-2450S dipole antennas with 5” pigtail and MMCX connector, configuration/testing software, Integration engineering support SDKSDK-4424I4424I-200: 200 Includes (2) AC4424-200 transceivers, (2) RS232 Serial Adapter Boards, (2) 6Vdc unregulated power supplies, (2) Serial cables, (2) S151FL-5-RMM-2450S dipole antennas with 5” pigtail and MMCX connector, configuration/testing software, Integration engineering support 12/09/02 32
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Producer : Acrobat Distiller 4.0 for Windows Creator : Microsoft Word 9.0 Modify Date : 2004:03:17 15:52:10+01:00 Author : N. Zach Hogya Title : AC4424 Create Date : 2003:01:30 14:48:07 Page Count : 32 Page Mode : UseNone Has XFA : NoEXIF Metadata provided by EXIF.tools