Ezurio BT1 TiWi-uB2 Bluetooth Module User Manual manual
LS Research, LLC TiWi-uB2 Bluetooth Module manual
Ezurio >
manual
TiWi-uB2 / uBleu2 Module DATASHEET TiWi-uB2 / uBleu2 Bluetooth Module FEATURES DESCRIPTION Built in CC2564 single-chip Bluetooth fully supports BT 2.1 + EDR, BLE 4.0. RF Output Power: +10 dBm (Class 1.5) RF Receive Sensitivity: -94 dBm Miniature Size: 7 mm x 7 mm x 1.5 mm Operating Voltage: 2.2V to 4.8V Operating temperature: -30 to +85o C Worldwide acceptance: FCC (USA), IC (Canada), and CE (Europe) RoHS compliant Supports maximum Bluetooth data rates over HCI UART interface. Supports multiple Bluetooth profiles with enhanced QoS, both mono and stereo, assisted A2DP APPLICATIONS Medical (ex Heart Rate Monitor, Blood Pressure Sensor, Blood Glucose Meter) Thermometer Flood Alarm Heating Control Automatic Key Control Industrial Sensors Toys Entertainment Devices Mobile Accessories All Bluetooth Wireless Applications LSR would like to announce a low-cost and lowpower consumption module which has all of the Bluetooth functionalities. The highly integrated TiWi-uB2 module makes the use of Bluetooth headsets and other applications possible. The TiWi-uB2 module fully supports the dual mode Bluetooth and BLE operation, and the output power can support class 1.5. The SIP module provides UART interface / audio PCM interface for Bluetooth. The SIP module is specifically developed for Smart phones and Portable devices. Need to get to market quickly? Not an expert in Bluetooth? Need a custom antenna? Do you need help with your host board? LS Research Design Services will be happy to develop custom hardware or software, or help integrate the design. Contact us at sales@lsr.com or call us at 262-375-4400. ORDERING INFORMATION Order Number 450-0104 450-0104R 450-0105 Description TiWi-uB2 Module (Tray) TiWi-uB2 Module (Tape & Reel) TiWi-uB2 EM Board Table 1 Orderable Model Numbers The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 1 of 25 TiWi-uB2 / uBleu2 Module DATASHEET MODULE ACCESSORIES Order Number Description 001-0001 2.4 GHz Dipole Antenna with Reverse Polarity SMA Connector 080-0001 U.FL to Reverse Polarity SMA Bulkhead Cable 105mm Table 2 Module Accessories The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 2 of 25 TiWi-uB2 / uBleu2 Module DATASHEET TABLE OF CONTENTS FEATURES .......................................................................................................................... 1 APPLICATIONS ................................................................................................................... 1 DESCRIPTION ..................................................................................................................... 1 ORDERING INFORMATION ................................................................................................ 1 MODULE ACCESSORIES ................................................................................................... 2 FOOTPRINT AND PIN DEFINITIONS.................................................................................. 5 PIN DESCRIPTIONS ............................................................................................................ 6 ELECTRICAL SPECIFICATIONS ........................................................................................ 7 Absolute Maximum Ratings ....................................................................................................................... 7 Recommended Operating Conditions ...................................................................................................... 7 General Characteristics .............................................................................................................................. 8 Bluetooth RF Characteristics .................................................................................................................. 10 BLUETOOTH POWER-UP/ DOWN SEQUENCE .............................................................. 11 nSHUTD Requirements............................................................................................................................. 11 SLOW CLOCK (32 KHZ) SOURCE REQUIREMENTS ..................................................... 12 BLUETOOTH HCI UART ................................................................................................... 13 BLUETOOTH AUDIO CODEC/PCM .................................................................................. 14 SOLDERING RECOMMENDATIONS ................................................................................ 15 Recommended Reflow Profile for Lead Free Solder ............................................................................. 15 CLEANING ......................................................................................................................... 16 OPTICAL INSPECTION ..................................................................................................... 16 REWORK ........................................................................................................................... 16 SHIPPING, HANDLING, AND STORAGE ......................................................................... 16 Shipping ..................................................................................................................................................... 16 Handling ..................................................................................................................................................... 16 Moisture Sensitivity Level (MSL) ............................................................................................................. 16 Storage ....................................................................................................................................................... 16 The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 3 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Repeating Reflow Soldering .................................................................................................................... 17 AGENCY CERTIFICATIONS ............................................................................................. 18 AGENCY STATEMENTS ................................................................................................... 18 Federal Communication Commission Interference Statement ............................................................ 18 Industry Canada Statements.................................................................................................................... 19 OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS ....................................................................................................... 20 OEM LABELING REQUIREMENTS FOR END-PRODUCT .............................................. 21 OEM END PRODUCT USER MANUAL STATEMENTS.................................................... 22 MECHANICAL DATA......................................................................................................... 23 CONTACTING LS RESEARCH ......................................................................................... 25 The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 4 of 25 TiWi-uB2 / uBleu2 Module DATASHEET FOOTPRINT AND PIN DEFINITIONS Figure 1 TiWi-uB2 Module Schematic View Figure 2 TiWi-uB2 Module Footprint View The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 5 of 25 TiWi-uB2 / uBleu2 Module DATASHEET PIN DESCRIPTIONS Module Pin Name I/O Type HCI_CTS HCI UART CLEAR-TO-SEND HCI_TX HCI UART DATA TRANSMIT HCI_RX HCI UART DATA RECEIVE HCI_RTS HCI UART REQUEST-TO-SEND GND GND GROUND GND GND GROUND GND GND GROUND SLOW_CLK_IN GND GND 10 NC1 NO CONNECT 1 (DO NOT CONNECT) 11 NC2 NO CONNECT 2 (DO NOT CONNECT) 12 VBAT PI POWER TO MODULE (2.2V - 4.8V) 13 GND GND 14 BT_ANT RF 15 GND GND 16 nSHUTD 17 GND GND 18 VDD_IO PI 19 AUD_IN PCM DATA INPUT (IF NOT USED, DO NOT CONNECT) 20 AUD_OUT PCM DATA OUTPUT (IF NOT USED, DO NOT CONNECT) 21 AUD_CLK IO PCM CLOCK (IF NOT USED, DO NOT CONNECT) 22 AUD_FSYNC IO PCM FRAME SYNCH (IF NOT USED, DO NOT CONNECT) 23 NC3 NO CONNECT 3 (DO NOT CONNECT) 24 TX_DBG LOGGER OUTPUT 25-33 GND GND Description 32.768 kHz CLOCK IN GROUND GROUND ANTENNA, 50 OHMS GROUND SHUTDOWN INPUT (ACTIVE LOW) GROUND I/O POWER SUPPLY (1.8V NOMINAL) GROUND PI = Power Input I = Input O = Output IO = Bi-directional Input Output Port RF = Bi-directional RF Port GND=Ground Table 3 TiWi-uB2 Pin Descriptions The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 6 of 25 TiWi-uB2 / uBleu2 Module DATASHEET ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings Symbol VBAT VDD_IO Description Input supply Voltage Min Max Unit -0.5 5.5 2.145 Digital Bluetooth I/O Voltage -0.5 Table 4 Absolute Maximum Ratings Recommended Operating Conditions Test conditions: Ambient Temp = 25°C Symbol Min Typ Max Unit VBAT 2.2 3.3 4.8 1.62 1.8 1.92 Table 5 Recommended Operating Conditions VDD_IO Under no circumstances should exceeding the ratings specified in the Absolute Maximum Ratings section be allowed. Stressing the module beyond these limits may result permanent damage to the module that is not covered by the warranty. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 7 of 25 TiWi-uB2 / uBleu2 Module DATASHEET General Characteristics Characteristic Description Model Name TiWi-uB2 Product Description Bluetooth Wireless Module Dimension 7.0 mm x 7.0 mm x 1.5 mm (W*L*T) BT Interface HCI UART, Audio PCM Operating temperature -30°C to 85°C Storage temperature -40°C to 85°C Humidity Operating Humidity 10% to 95% Non-Condensing Storage Humidity 5% to 95% Non-Condensing Weight 0.18 g +/- 0.01g Table 6 General Characteristics Current Consumption – for Different Bluetooth BR/EDR Scenarios Conditions: VBAT = 3.6 V, VDDIO = 1.8V 25°C, 26-MHz fast clock, nominal unit, 4 dBm output power Mode Description Master/Slave Average Current Unit Idle current (ARM off) Master/slave 2.5 mA SCO link HV3 Master/slave 12 mA eSCO link EV3 64 kbps, no retransmission Master/slave 11.5 mA eSCO link 2-EV3 64 kbps, no retransmission Master/slave 8.3 mA GFSK full throughput: TX = DH1, RX = DH5 Master/slave 38.5 mA EDR full throughput: TX = 2-DH1, RX = 2-DH5 Master/slave 39.2 mA EDR full throughput: TX = 3-DH1, RX = 3-DH5 Master/slave 39.2 mA Sniff, one attempt, 1.28 s Master/slave 76/100 µA Page or inquiry scan 1.28 s, 11.25 ms Master/slave 300 µA Page (1.28 s) and inquiry (2.56 s) scans, 11.25 ms Master/slave 430 µA Low power scan, 1.28-s interval, quiet environment Master/slave 135 µA Table 7 Bluetooth Power Consumption The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 8 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Current Consumption – for Different Bluetooth LE Scenarios Conditions: VBAT = 3.6 V, VDDIO = 1.8V, 25°C, 26-MHz fast clock, nominal unit, 10 dBm output power Mode Description Average Current Unit Advertising, nonconnectable Advertising in all 3 channels 1.28msec advertising interval 15Bytes advertise data 104 µA Advertising, discoverable Advertising in all 3 channels 1.28msec advertising interval 15Bytes advertise data 121 µA Listening to a single frequency per window 1.28msec scan interval 11.25msec scan window 302 µA 500msec connection interval 0msec Slave connection latency Empty Tx/Rx LL packets 169 µA Scanning Connected (master role) Table 8 Bluetooth Power Consumption Power Consumption – Bluetooth Conditions: VBAT = 3.3V, VDDIO = 1.8V, Ambient Temp = 25°C Packet type Typ Max Unit DM1 47.1 mA DH1 30.2 mA DM3 21.3 mA DH3 17.4 mA DM5 15.6 mA DH5 13.0 mA Deep Sleep Mode 0.033 mA Constant RX 44.5 mA BER Mode 38.8 mA Table 9 Bluetooth VBAT Power Consumption Packet type Typ Max Unit DM1 0.069 mA DH1 0.069 mA DM3 0.069 mA DH3 0.069 mA DM5 0.069 mA DH5 0.069 mA Deep Sleep mode 0.032 mA Constant RX 0.069 mA BER Mode 0.069 mA Table 10 Bluetooth VDDIO Power Consumption The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 9 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Bluetooth RF Characteristics General Specifications Feature Description Bluetooth Standard Bluetooth 4.0 (with EDR) Host Interface HCI UART, PCM Antenna Reference Small antennas with 0~2 dBi peak gain Frequency Band 2.402 GHz ~ 2.480 GHz Number of Channels 79 channels Modulation FHSS, GFSK, DPSK, DQPSK Table 11 Bluetooth General Specifications RF Characteristics Test Conditions : VBAT = 3.3V, VDDIO = 1.8V Characteristic Condition -30°C Typ 25°C Typ Output Power Class 1.5 9.5 10 10.8 dF1 avg 158 158 158 140~ 175 KHz dF2 max 138 137 136 >115 KHz dF2avg / dF1avg 90 90 90 80 RMS DEVM 13 99% DEVM 10 10 10 20 Peak DEVM 13 13 13 25 -95 -94 -93 -70 dBm π/4-DQPSK at BER = 0.01% -93 -92 -91 -70 dBm 8DPSK at BER = 0.01% -86 -85 -84 -70 dBm GFSK at BER = 0.1% -5 -5 -5 -20 dBm -10 -10 -10 -20 dBm -10 -20 dBm Modulation GFSK Modulation EDR at 8DPSK GFSK at BER = 0.1% Sensitivity at Dirty Tx On Maximum Input Level π/4-DQPSK at BER = 0.1% 8DPSK at BER = 0.1% -10 -10 Table 12 Bluetooth RF Characteristics 85°C Typ BT Spec Unit dBm The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 10 of 25 TiWi-uB2 / uBleu2 Module DATASHEET BLUETOOTH POWER-UP/ DOWN SEQUENCE Figure 3 Bluetooth Power-Up/Down Sequence nSHUTD Requirements Parameter Symbol Min Max Unit Operation mode level (1) VIH 1.42 1.98 Shutdown mode level (1) VIL 0.4 20 us Minimum time for nSHUT_DOWN low to reset the device Rise/fall times Tr/Tf (1) Internal pull-down retains shutdown mode when no external signal is applied to this pin. Table 13 nSHUTD Requirements The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 11 of 25 TiWi-uB2 / uBleu2 Module DATASHEET SLOW CLOCK (32 KHZ) SOURCE REQUIREMENTS External Slow Clock signal characteristics Characteristic Condition Sym Min Input slow clock frequency Typ Max 32768 Input slow clock accuracy (Initial + temp + aging) Unit Hz -250 250 ppm Input transition time tr/tf - 10% to 90% tr/tf 100 ns Frequency input duty cycle 15 85 At 1 kHz -125 dBc/Hz Integrated over 300 to 15000 Hz Hz Phase noise Jitter Slow clock input voltage limits Square wave, DC coupled 50 VIH 0.65 x VDD_IO VDD_IO V peak VIL 0.35 x VDD_IO V peak Input impedance Input capacitance MΩ pF Table 14 32 kHz Clock Requirements The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 12 of 25 TiWi-uB2 / uBleu2 Module DATASHEET BLUETOOTH HCI UART Figure 4 Bluetooth HCI UART Timing Symbol Characteristic Condition Min Typ Max Unit Baud rate 37.5 4000 kbps Baud rate accuracy -2.5 1.5 t3 CTS low to TX_DATA on t4 CTS high to TX_DATA off t6 CTS high pulse width t1 RTS low to RX_DATA on t2 RTS high to RX_DATA off Hardware flow control Interrupt set to ¼ FIFI us byte Bit us 16 byte Table 15 Bluetooth HCI UART Timing The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 13 of 25 TiWi-uB2 / uBleu2 Module DATASHEET BLUETOOTH AUDIO CODEC/PCM Figure 5 Bluetooth PCM Timing PCM Master Symbol Parameter Condition Min Max Unit 15625 (64 kHz) ns Tclk Cycle time 166.67 (6 MHz) TW High or low pulse width 50% of Tclk min ns tis AUD_IN setup time 25 ns tih AUD_IN hold time ns top AUD_OUT propagation time 40pF load 10 ns top FSYNC_OUT propagation time 40pF load 10 ns Max Unit Table 16 Bluetooth PCM Master Timing PCM Slave Symbol Parameter Condition Tclk Cycle time TW High or low pulse width tis Min 62.5 (16 MHz) ns 40% of Tclk ns AUD_IN setup time ns tih AUD_IN hold time ns tis AUD_FSYNC setup time ns tih AUD_FSYNC hold time ns top AUD_OUT propagation time 40pF load 21 ns Table 17 Bluetooth PCM Slave Timing The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 14 of 25 TiWi-uB2 / uBleu2 Module DATASHEET SOLDERING RECOMMENDATIONS Recommended Reflow Profile for Lead Free Solder Figure 6 Recommended Soldering Profile Note: The quality of solder joints on the surface mount pads where they contact the host board should meet the appropriate IPC Specification. See IPC-A-610-D Acceptability of Electronic Assemblies, section 8.2.1 “Bottom Only Terminations.” The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 15 of 25 TiWi-uB2 / uBleu2 Module DATASHEET CLEANING SHIPPING, HANDLING, AND STORAGE In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed with any cleaning process. Shipping Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pads. Water could also damage any stickers or labels. Cleaning with alcohol or a similar organic solvent will likely flood soldering flux residuals into the RF shield, which is not accessible for post-washing inspection. The solvent could also damage any stickers or labels. Ultrasonic cleaning could damage the module permanently. OPTICAL INSPECTION After soldering the Module to the host board, consider optical inspection to check the following: Proper alignment and centering of the module over the pads. Proper solder joints on all pads. Excessive solder or contacts to neighboring pads, or vias. REWORK The module can be unsoldered from the host board if the Moisture Sensitivity Level (MSL) requirements are met as described in this datasheet. Never attempt a rework on the module itself, e.g. replacing individual components. Such actions will terminate warranty coverage. Bulk orders of the TiWi-uB2 modules are delivered in trays of 416 (13 x 32) or reels of 2,000. Handling The TiWi-uB2 modules contain a highly sensitive electronic circuitry. Handling without proper ESD protection may damage the module permanently. Moisture Sensitivity Level (MSL) Per J-STD-020, devices rated as MSL 4 and not stored in a sealed bag with desiccant pack should be baked prior to use. After opening packaging, devices that will be subjected to reflow must be mounted within 72 hours of factory conditions (<30°C and 60% RH) or stored at <10% RH. Bake devices for 48 hours at 125°C. Storage Please use this product within 6 months after receipt. Any product used after 6 months of receipt needs to have solderability confirmed before use. The product shall be stored without opening the packing under the ambient temperature from 5 to 35deg.C and humidity from 20 to 70%RH. (Packing materials, in particular, may be deformed at the temperatures above this range.) Do not store in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX. Do not store in direct sunlight. The product should not be subject to excessive mechanical shock. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 16 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Repeating Reflow Soldering Only a single reflow soldering process is encouraged for host boards. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 17 of 25 TiWi-uB2 / uBleu2 Module DATASHEET AGENCY CERTIFICATIONS FCC ID: TFB-BT1, 15.247 IC ID: 5969A-BT1, RSS 210 CE: Compliant to standards EN 60950-1, EN 300 328, and EN 301 489 AGENCY STATEMENTS Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This portable transmitter with its antenna complies with FCC/IC RF exposure limits for general population / uncontrolled exposure. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 18 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Industry Canada Statements This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device has been designed to operate with the antenna(s) listed below, and having a maximum gain of 2.0 dBi (LSR Dipole) and 1.3dBi (Johanson Chip). Antennas not included in this list or having a gain greater than 2.0 dBi and 1.3dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. List of all Antennas Acceptable for use with the Transmitter 1) LS Research 001-0001 center-fed dipole antenna and LS Research 080-0001 U.FL to Reverse Polarity SMA connector cable. 2) Johanson 2450AT43B100 chip antenna. Cet appareil est conforme aux normes d'Industrie Canada exempts de licence RSS (s). L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. Pour réduire le risque d'interférence aux autres utilisateurs, le type d'antenne et son gain doiventêtre choisis de manière que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pascelle permise pour une communication réussie. Cet appareil a été conçu pour fonctionner avec l'antenne (s) ci-dessous, et ayant un gain maximum de 2,0 dBi (LSR dipôle) et1.3dBi (Chip Johanson). Antennes pas inclus danscette liste ou d'avoir un gain supérieur à 2,0 dBi et-1.3dBi sont strictement interdites pour l'utilisation avec cet appareil. L'impédance d'antenne requise est de 50 ohms. Liste de toutes les antennes acceptables pour une utilisation avec l'émetteur 1) LS Research 001-0001 alimenté par le centre antenne dipôle et LS Research 080-0001 U.FL d'inversion de polarité du câble connecteur SMA. 2) Antenne Johanson puce 2450AT43B100. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 19 of 25 TiWi-uB2 / uBleu2 Module DATASHEET OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS The TiWi-uB2 Module has been certified for integration into products only by OEM integrators under the following conditions: The antennas for this transmitter must not be co-located with any other transmitters except in accordance with FCC and Industry Canda multi-transmitter procedures. Co-location means having a separation distance of less than 20 cm between transmitting antennas. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC and Industry Canada authorizations are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC and Industry Canada authorization. Le module de TiWi-uB2 a été certifié pour l'intégration dans des produits uniquement par des intégrateurs OEM dans les conditions suivantes: Les antennes pour ce transmetteur ne doit pas être co-localisés avec les autres émetteurs sauf en conformité avec la FCC et Industrie Canada multi-émetteur procédures. Co-localisation des moyens ayant une distance de séparation inférieure à 20 cm entre les antennes d'émission. Tant que les deux conditions précitées sont réunies, les tests de transmetteurs supplémentaires ne seront pas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leur produit final pour toutes les exigences de conformité supplémentaires requis avec ce module installé (par exemple, les émissions appareil numérique, les exigences de périphériques PC, etc.) NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (pour certaines configurations ou de co-implantation avec un autre émetteur), puis la FCC et Industrie autorisations Canada ne sont plus considérés comme valides et l'ID de la FCC et IC numéro de certification ne peut pas être utilisé sur la produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'un distincte de la FCC et Industrie Canada l'autorisation. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 20 of 25 TiWi-uB2 / uBleu2 Module DATASHEET OEM LABELING REQUIREMENTS FOR END-PRODUCT The TiWi-uB2 module is labeled with its own FCC ID and IC Certification Number. The FCC ID and IC certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module. The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: TFB-BT1” “Contains Transmitter Module IC: 5969A-BT1” or “Contains FCC ID: TFB-BT1” “Contains IC: 5969A-BT1” The OEM of the TiWi-uB2 Module must only use the approved antenna(s) listed above, which have been certified with this module. Le module de TiWi-uB2 est étiqueté avec son propre ID de la FCC et IC numéro de certification. L'ID de la FCC et IC numéros de certification ne sont pas visibles lorsque le module est installé à l'intérieur d'un autre appareil, comme par exemple le terminal dans lequel le module est installé doit afficher une etiquette faisant référence au module ci-joint. Le produit final doit être étiqueté dans un endroit visible par le suivant: “Contient Module émetteur FCC ID: TFB-BT1" “Contient Module émetteur IC: 5969A-BT1" ou “Contient FCC ID: TFB-BT1" “Contient IC: 5969A-BT1" Les OEM du module TiWi-uB2 ne doit utiliser l'antenne approuvée (s) ci-dessus, qui ont été certifiés avec ce module. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 21 of 25 TiWi-uB2 / uBleu2 Module DATASHEET OEM END PRODUCT USER MANUAL STATEMENTS The OEM integrator should not provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. Other user manual statements may apply. L'intégrateur OEM ne devraient pas fournir des informations à l'utilisateur final sur la façon d'installer ou de supprimer ce module RF ou modifier les paramètres liés RF dans le manuel utilisateur du produit final. Autres déclarations manuel de l'utilisateur peuvent s'appliquer. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 22 of 25 TiWi-uB2 / uBleu2 Module DATASHEET MECHANICAL DATA Figure 7 Module Mechanical Dimensions The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 23 of 25 TiWi-uB2 / uBleu2 Module DATASHEET Figure 8 Soldering Footprint for Host Board and Module Placement The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 24 of 25 TiWi-uB2 / uBleu2 Module DATASHEET CONTACTING LS RESEARCH Headquarters LS Research, LLC W66 N220 Commerce Court Cedarburg, WI 53012-2636 USA Tel: 1(262) 375-4400 Fax: 1(262) 375-4248 Website www.lsr.com Wiki wiki.lsr.com Technical Support forum.lsr.com Sales Contact sales@lsr.com The information in this document is provided in connection with LS Research (hereafter referred to as “LSR”) products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of LSR products. EXCEPT AS SET FORTH IN LSR’S TERMS AND CONDITIONS OF SALE LOCATED ON LSR’S WEB SITE, LSR ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL LSR BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF LSR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. LSR makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. LSR does not make any commitment to update the information contained herein. Unless specifically provided otherwise, LSR products are not suitable for, and shall not be used in, automotive applications. LSR’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. The information in this document is subject to change without notice. TiWi-uB2 uBleu2 Datasheet Copyright © 2012 LS Research, LLC Page 25 of 25
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : chofmeister Create Date : 2012:11:15 14:24:51-06:00 Modify Date : 2012:11:15 15:29:08-06:00 Language : en-US XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Format : application/pdf Creator : chofmeister Creator Tool : Microsoft® Word 2010 Metadata Date : 2012:11:15 15:29:08-06:00 Producer : Microsoft® Word 2010 Document ID : uuid:8c5a6a71-bd9c-4c9c-9b61-3fc0bd324608 Instance ID : uuid:4c7e4ab5-f6fe-4723-8aba-f9a18ceff81e Page Count : 25EXIF Metadata provided by EXIF.tools