User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3603867 |
| Application ID | jjlwhucUwwf9KYWPUuTynw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 98.62kB (1232697 bits) |
| Date Submitted | 2017-10-13 00:00:00 |
| Date Available | 2018-04-12 00:00:00 |
| Creation Date | 2017-10-13 16:08:21 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2017-10-13 16:08:25 |
| Document Title | User Manual |
| Document Creator | Microsoft® Office Word 2007 |
Future Communication IC Inc. User Manual Initial Setup FCM9000x series Ultra-Low Power Wi-Fi Module for IoT Solution Release version 1.1 Date of release: October 11, 2017 Contact information For more information, please visit: http://www.fci.co.kr For sales office addresses, please send an email to: fci_sales@fci.co.kr All information provided in this document is subject to legal disclaimer. © FCI 2017. All rights reserved. FCM9000x User manual Setup and Measurement Future Communication IC Inc. Revision History Version Date Writer 1.0 2017.08.11 WG-FAE 1.1 2017.10.11 WG-FAE Contents Remarks Add warning statement All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 2 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. Contents 1. FCM9000x series Module Board ...................................................................................................................... 4 1.1. Board description ................................................................................................................................... 4 1.2. USB to serial Driver ............................................................................................................................... 6 2. Setup Serial Terminal Utility .............................................................................................................................. 7 3. FC9000 setup .............................................................................................................................................................. 8 4. 3.1. Setup STA Mode ..................................................................................................................................... 8 3.1.1. Normal Mode (None DPM) ............................................................................................................... 8 3.2. Setup Soft-AP Mode ........................................................................................................................... 12 Federal Communication Commission Interference Statement...................................................... 16 5. Industry Canada statement................................................................................................................................... 17 All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 3 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. 1. FCM9000x series Module Board 1.1. Board description 16 10 11 13 14 15 12 Fig 1. FCM9000NP1000 Module EVB w/ pattern antenna 1) FCM9000x module board, Two versions based on Antenna; Pattern Antenna, Wired external Antenna 2) Interface board for module 3) Micro USB connector to supply power and to control Board 4) RF input/output: path for R/Tx 5) LED indicator for USB power (5V) 6) Uart0 RS-232 Pinout 7) Uart1 RS-232 Pinout All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 4 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. 8) Jtag pin 9) GPIO pinout 10) Power switch for FC9000 module VDD The switch should be on for normal operation The switch should be off stage before micro USB cable is disconnected Power off Power on (Normal operation) 11) Wakeup Key of FCM9000N module Normal operation Wakeup Interrupt 12) RTC Power switch of FCM9000N module RTC Power off RTC Power ON (Normal operation) 13) FT2232 USB IC reset button 14) Factory reset button (not available, will be updated 15) WPS button (not available, will be updated) 16) Pin header for Current measurement Pin header should be short for normal operation 3.3V operation All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 5 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. 1.2. USB to serial Driver This Board supports both serial port (UART) and USB (default USB) If use a USB port, install the FT232 Driver for windows. In most cases, it will be installed automatically, but if not installed, you can get the driver from the following address. http://www.ftdichip.com/Drivers/CDM/CDM21224_Setup.zip All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 6 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. 2. Setup Serial Terminal Utility To connect to console of FCM9000x board, below configuration is required: Port: Com Port Number on Windows System Baud rate: 115,200 bps Data bits: 8 bits Parity: None Stop bits: 1 bit Flow control: None All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 7 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. 3. FC9000 setup The FC9000 device supports the Soft-AP, Station and Wi-Fi Direct modes Station: a device that has the capability to use the 802.11 protocol Soft-AP: Software enabled access point, This is software enabling FC9000 which hasn't been specifically made to be a router into a wireless access point Wi-Fi direct: called Wi-Fi P2P, is a Wi-Fi standard enabling devices to easily connect with each other without requiring a wireless access point 3.1. Setup STA Mode 3.1.1. Normal Mode (None DPM) Step 1) Clear all saved configuration. (Using “factory” command) All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 8 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. Step 2) Boot FC9000 and run “setup” on console Step 3) Stop all services for the setting Yes Step 4) Select Country Code. (Type national code as two Capital Character) Step 5) Select running mode as “1. Station All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 9 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. Step 6) Select legacy-AP to connect and input index number and password (if required) Step 7) Confirm Configuration Step 8) Select IP address mode Automatic: DHCP Client mode Static IP: Static IP address mode Step 9) Select DPM mode All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 10 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. Step 10) Station mode ready All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 11 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. 3.2. Setup Soft-AP Mode Step 1) Boot FC9000 and run “setup” on console Step 2) Stop all services for the setting Yes Step 3) Select Country Code (Type national code as two Capital Character) All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 12 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. Step 4) Select running mode as “2. Soft-AP” (depending on the SDK package, you may see fewer options) Step 5) Input AP SSID / Channel number / Security mode SSID (Service set identifier): String ( alphabet / Unicode / number ) Channel: Running channel number Security: Default is “OPEN” mode for easy setup All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 13 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. Step 6) Input IP-address of Soft-AP. (This address will be used as “default gateway address”) IP address / Subnet mask / Default gateway / DNS address “Enter” key without new input address will be set as default value. Step 7) Configure DHCP server All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 14 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. Step 8) Confirm Soft-AP configuration Step 9) Search Wi-Fi AP on your Window-PC, Tablet, Smart Phone or other Wi-Fi station device All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 15 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. 4. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condition s: (1) This device may not cause harmful interference, and (2) this device must accept any interference re ceived, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursu ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against har mful interference in a residential installation. This equipment generates, uses and can radiate radio frequ ency energy and, if not installed and used in accordance with the instructions, may cause harmful interfe rence to radio communications. However, there is no guarantee that interference will not occur in a part icular installation. If this equipment does cause harmful interference to radio or television reception, whi ch can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is con nected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Radiation Exposure Statement: This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and the maximum antenna gain allowed for use with this device is 2.5 dBi. 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requireme nts required with this module installed. All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 16 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop confi gurations or co-location with another transmitter), then the FCC authorization is no longer considered va lid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FC C authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such tha t 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2AMRF-FCM9000N”. The grantee's FCC ID can be use d only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The en d user manual shall include all required regulatory information/warning as show in this manual. 5. Industry Canada statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1) l'appareil ne doit pas produire de brouillage, et 2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. This Class B digital apparatus complies with Canadian ICES-003. All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 17 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. The County Code Selection feature is disabled for products marketed in the US/ Canada. La fonction de sélection de l'indicatif du pays est désactivée pour les produits commercialisés aux États-Unis et au Canada. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. Thi s equipment should be installed and operated with minimum distance 20cm between the radiator & you r body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnem ent non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance ent re la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM in tegrator is still responsible for testing their end-product for any additional compliance requirements requ ired with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'an tenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pa s nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 18 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-locati on with another transmitter), then the Canada authorization is no longer considered valid and the IC ID c an not be used on the final product. In these circumstances, the OEM integrator will be responsible for r e-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'or dinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une au torisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such tha t 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 22972-FCM9000N”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut êt re installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 22972-FCM9000N". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la fa All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 19 / 20 FCM9000x User manual Setup and Measurement Future Communication IC Inc. çon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertisseme nts comme indiqué dans ce manuel. All information provided in this document is subject to legal disclaimer © FCI 2016-2017. All rights reserved. FCM9000x User Manual Version 1.0 / Date of release: August 11, 2017 20 / 20
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2017:10:13 16:08:21+08:00 Creator Tool : Microsoft® Office Word 2007 Modify Date : 2017:10:13 16:08:25+08:00 Metadata Date : 2017:10:13 16:08:25+08:00 Producer : Microsoft® Office Word 2007 Format : application/pdf Document ID : uuid:c635e287-7ead-4ee9-9d50-c3a922a55294 Instance ID : uuid:f7a4d563-5912-433c-a2e8-d63ca669c854 Page Count : 20 Language : zh-TW Creator : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools