FEIBIT ELECTRONIC TECHNOLOGY FNB56A6F ZigBee module User Manual

SHENZHEN FEIBIT ELECTRONIC TECHNOLOGY Co., LTD ZigBee module

Users manual

Download: FEIBIT ELECTRONIC TECHNOLOGY FNB56A6F ZigBee module User Manual
Mirror Download [FCC.gov]FEIBIT ELECTRONIC TECHNOLOGY FNB56A6F ZigBee module User Manual
Document ID3597750
Application ID3shgHeuADc8qPvOAVrit2Q==
Document DescriptionUsers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize8.61kB (107584 bits)
Date Submitted2017-10-10 00:00:00
Date Available2017-10-10 00:00:00
Creation Date2017-10-10 14:11:52
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2017-10-10 14:11:52
Document TitleMicrosoft Word - User Manual
Document CreatorPScript5.dll Version 5.2.2
Document Author: Administrator

User Guide
The FNB56A6 module belongs to NXP module, which is used
for the development of door lock, sensor, infrared treasure and
other equipment. Modules with a total of 18 pins, retained the USB
TO TTL interface, UART interface, and the ADC interface.The module
best working in the recommended application condition , it is best
not to let the module working under the condition of the limit of
application. The module is equipped with a shield, insulated from
external signals, external ceramic antennas for enhanced module's
sending and receiving signals.
Pin Assignments:
Pin number
I/O
Name
Description
VCC
Power input(+3.3V)
I/O
P17
Digital I/O
I/O
P13
Digital I/O
GND
Ground
I/O
P19
Digital I/O
I/O
P5
Digital I/O
I/O
P18
Digital I/O
I/O
P16
Digital I/O
I/O
P11
Digital I/O
10
I/O
P9
Digital I/O
11
I/O
P12
Digital I/O
12
I/O
P1
Digital I/O
13
GND
Ground
14
RESET_N
15
I/O
P6
TX
16
I/O
P7
RX
17
VCC
Power input(+3.3V)
18
I/O
DO1
Send 0 to clear the input
System RESET Signal,Low Level Active
Features:

Follow IEEE802.15.4 Standard

32-KB RAM

ZigBee Systems(512-KB Flash)

Home/Building Automation

Industrial Control and Monitoring

Low-Power Wireless Sensor Networks

Consumer Electronics

Supply Voltage 2.0V-3.6V

Operation frequency: 2405-2480MHz

Conform to ZigBee Standard,support ZLL and ZHA.

Support ceramic Antenna

Use UART communication,and support to upgrade software by UART

Integrate with 2.4G low power consumption of transceiver

Temperature range:-40℃ ~ + 125℃

2-wire I2C-bus compatible serial interface; can operate as either master or slave

128-bit AES security processor

RX current 14.7 mA, in low power receive mode 13 mA

Very thin quad flat 6 x6 mm, 40 terminal package; lead-free and RoHS compliant
FCC compliance
This device complies with Part 15 of the FCC Rules.
Part Number
FCC ID
FNB56A6
2AE8BFNB56A6F
Operation is subject to the following two conditions: (1)this device may not cause
harmful interface,and (2)this device must accept any interface received,including interface
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device must be installed and used in strict accordance with the manufacturer’s
instructions as described in the user documentation that comes with the product.
Warning for FNB56A6:This device complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment.This device and its antenna(s) must not be
co-located or operating in conjunction with any other antenna or transmitter.
The final end product must be labeled in a visible area with the following:Contains
FCC ID: 2AE8BFNB56A6F.
The OEM integrator is responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device
emission, PC peripheral requirements, etc.).
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one
or more of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
FCC Radiation Exposure Statement:
This 2.4G Module complies with FCC radio‐frequency exposure guidelines set forth
for an uncontrolled environment.
This device is intended only for OEM integrators under the following conditions:
(1) According to FCC Part 15 Subpart C Section 15.212, the radio elements of the
modular transmitter must have their own shielding. This module is granted as a
Single Modular Approval.
(2) This device has been designed to operate with a External antenna having a
maximum gain of 2dBi(max.). Only this type of antenna may be used.
(3) Integration is typically strictly restricted to Grantee himself or dedicated OEM
integrators under control of the Grantee.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end‐product for any
additional compliance requirements required with this module installed (for example,
digital device emissions, PC peripheral requirements, etc.).
USER MANUAL OF THE END PRODUCT:
In the user manual of the end product, the end user has to be informed that the
equipment complies with FCC radio‐frequency exposure guidelines set forth for an
uncontrolled environment.
The end user has to also be informed that any changes or modifications not
expressly approved by the manufacturer could void the user's authority to operate
this equipment.
If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19
statement is required to be available in the user manual: This device complies with
Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following" Contains
TX FCC ID: 2AE8BFNB56A6F ". If the size of the end product is larger than 8x10cm,
then the following FCC part 15.19 statement has to also be available on the label:
This device complies with Part 15 of FCC rules. Operation is subject to the following
two conditions: (1)this device may not cause harmful interference and (2) this device
must accept any interference received, including interference that may cause
undesired operation.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Administrator
Create Date                     : 2017:10:10 14:11:52+08:00
Modify Date                     : 2017:10:10 14:11:52+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Producer                        : Acrobat Distiller 11.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - User Manual
Creator                         : Administrator
Document ID                     : uuid:3cd74928-2903-4b07-b141-eb947e36d2d2
Instance ID                     : uuid:334ca094-7305-4171-a634-684c46c0557a
Page Count                      : 5
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AE8BFNB56A6F

Navigation menu