FLYSKY RC MODEL TECHNOLOGY GT500 Digital proportional radio control system User Manual 2

Download:
Mirror Download [FCC.gov]
Document ID	3699708
Application ID	tdqhbCjaE3GNY81leczagw==
Document Description	User Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	289.32kB (3616477 bits)
Date Submitted	2018-01-02 00:00:00
Date Available	2018-02-16 00:00:00
Creation Date	2017-12-27 18:09:57
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2017-12-27 18:10:07
Document Title	User Manual 2
Document Creator	Adobe InDesign CS6 (Windows)

nigital Pronortional Itatlio control System FS-GTE
6. Function Settings
This section details functions and their use.
6.1 Model (MODEL)
The transmitter can hold up to 20 models (01—20), Each configuration can quickly
be recalled.
Setup:
1. Press the Navikey to enter the function menu, then press the Navikey again to
enter the MODEL menu. The model number will begin to flash.
2. Rotate the Navikey to select a model.
3. Press the Navikey to confirm model selection. Once the confirmation is complete
the model number will stop flashing.
6.2 Name (NAME)
“Ill HIM! I“ “I
“ll-ll I!!! II? AIS
Tlllfi [SHE HM SUE
ABS SVE DN
01 FLY5
This function is for naming a model using up to 4 characters in length : 0123456789 A B C D E F G H I J K L
MNOPQRSTUVWXYZ
Setup :
1. Press the Navikey to enter the function menu, then rotate the Navikey to select
NAME. Press the Navikey again to enter the function. The first letter/number of
the model name will begin to flash.
2. Rotate the Navikey to select a character and press the Navikey to confirm the
selection.
3. Repeat for the last 3 characters. When the final character has been set the
system will exit the function automatically.
6.3 Reverse (REV)
The reversing function is used to correct the direction of travel for any channel.
Setup :
1. Press the Navikey to enter the function menu, then rotate the Navikey to select
REV. Press the Navikey again to enter the function. The channel name and
number will begin to flash.
2. Rotate the Navikey to select a channel and press the Navikey to confirm the
selection.
3. Rotate the Navikey to select “REV" (reverse) or "NOR" (normal) and press the
Navikey to confirm. The system will then exit the function automatically.
mm I m l m
sul-rn m m l us
nun um email sin:
ABS svc UN
Hllllil III" I“ "I
SUI-"l I!!! ll? AIS
“Ill “If! EM SUE
1 FlEliir
The channel name will
—-be displayed here as
ST, TH or AUX.
FLY SKY
6.4 End Point Adjust (EPA)
The EPA function is used to set the travel limits for each channel.
Setup :
1. Press the Navikey to enter the function menu, then rotate the Navikey to select
EPA. Press the Navikey again to enter the function. The channel name and
number will begin to flash.
2. Rotate the Navikey to select a channel and press the Navikey to confirm the
selection.
3. Move the selected channels control surface (wheel trigger etc.) in the direction
of the end point you wish to set. The system will display L,F.U (left, front, up) or
R.B.D (right, back, down) depending on the selection. Press the Navikey again to
confirm.
4. Rotate the Navikey to change the endpoint position (%) and press the Navikey
to confirm,
5. Repeat as needed.
6.5 Sub Trim (SUB-TR)
This function can be used to change the centre point of any channel.
Example of use: to correct steering being out of alignment even if the transmitter
wheel is centered.
Setup :
1. Press the Navikey to enter the function menu, then rotate the Navikey to select
SUB—TR. Press the Navikey again to enter the function. The channel name and
number will begin to flash.
2. Rotate the Navikey to select a channel and press the Navikey to confirm the
selection.
3. Rotate the Navikey to change the channels center point. The system will display
an L (left) or R (right) depending on which direction the center point has been
moved. Press the Navikey to confirm.
4. Repeat as needed.
6.6 Dual/Rate (D/R)
This function is used to limit the ST or TH D/R.
Setup :
1. Press the Navikey to enter the function menu, then rotate the Navikey to select
D/R. Press the Navikey again to enter the function. The channel name and
number will begin to flash.
2. Rotate the Navikey to select a channel and press the Navikey to confirm the
selection.
3. Rotate the Navikey to change the D/R value (%) and press the Navikey to
confirm.
HIIIIH Illll! I“ I"
SlII-"I IIII [IF I“
III“ “If! EM “G
“I
2376
Depending on the
end point selected the
system will display [RED]
or [flu]-
lmn mu! m m
Ill-‘I'I m m us
mm um mm m:
ST
L50
Mllllll llllfl I“ [Pl
SIII-TI III “P I“
TIIII “If! “M “E
ST
10075
Iligital Pronortional nadio control System FS-GTE
6.7 Exponential (EXP) mm
This function is used to add a curve to the output of a channel. When set to 0 the Sim
curve response is linear, however when set to a positive or negative value the curve “I"
will no longer be linear.
Setup : Hi
This function can adjust the throttles response curve from -100%~100%. b
1. Use the NaviKey to select the [EXP] menu , press the Navikey to enter the menu. R B D
2. [EXP] will start flashing. Use the NaviKey to select [ST], [TH] (RED if trigger
pushed) or [TH](L.F.U if trigger pulled).
3. Press the Navikey then use the NaviKey to change the percentage.
4. Press the Navikey again to confirm. 2 ?3%
5. Repeat for other channels as needed.
6-8 A.B-5- (ABS) unnn mu m E"
This function uses the throttle output to create automatic braking in order to make SIll-TI nm II! II:
braking easier on different surfaces. “m “m cum 5“
Setup: ABS
This function only adjusts the throttle channel. There are 6 settings:
[BRK]: The amount of breaking applied for each pulse.
[DLY]: Amount of delay between the trigger being pushed and ABS becoming
active.
[CYC]: The interval between each pulse. The larger the value, the longer the pulse
interval.
[TGP]: Sets the trigger position that will activate the ABS function.
[DTY]: Changes the ratio between brake on and break off time. When this value is
changed the square wave controlling the brakes will no longer be symetrical " _
[STM]: Creates a mix between the steering and the ABS fucntion so that ABS canl ,
be automatically decreased or disabled when turning. The % sets the point in whichl ‘ Displays current
the steering will have to be turned in order to activate this function with a range ' channel position
between 07100%. E means the function will not activate until the trigger moves ‘
beyond that percentage, N means the breaking will be disabled until it reaches that
percentage.
Funt. Range Default Display
[BRK] 0~100% 50% BRK: 50x
[DLY] 0~i no% 0 DLY: 0x
[cvc1 20%~100% 50% CYC: 50x
[TGP] 1o%~1oo% 30% TGP: 3035
[DTV] —4~4 0 DTY: U
[STM] 513311333; OFF STM: OFF
FLY SKY
Setup :
1. Press the Navikey to enter the function menu, then rotate the Navikey to select ABS. Press the Navikey
again to enter the function. ABS will begin to flash at the bottom of the screen. (This function needs to be
active to use. Press the NaviKey when A85 is flashing and rotate the Navikey to turn it on, then press the
NaviKey to confirm and repeat step 1.)
2. Rotate the Navikey to select an ABS function and press the Navikey to confirm the selection,
3. Rotate the Navikey to change the function value and press the Navikey to confirm.
4. Repeat as needed.
6.9 Tr|m (T RlM) mum um m m
This function is used to change the center point of each channel. For example if the sn-m m in us
steering wheel, when centered, leaves the models wheels pointing out of alignment,
this function can be used to correct it.
TIII “If! HM “I:
Setup:
This function can used to adjust 4 channels: steering, throttle, channel 3 and
channel 4. The adjustment range is between 07120. Adjustments may also be made
on the fly using the trim buttons. The direction from the centre will be represented
as l. (left) or R (right) for steering, F (forward) or B (back) for throttle and U (up) or D
(down) for AUX 3 and 4.
1. Use the NaviKey to select the [TRIM] menu, press the Navikey to edit the 3 U 50
function.
[ST] will flash. Use the NaviKey to select a channel, then press the Navikey.
With a channel selected use the NaviKey to change the percentage.
Press the Navikey to save and exit.
Repeat for other channels as needed.
6.10 Failsafe (F.SAFE) mu m;
This function protects the model, the safety of the user and others. When active the sun-Tn nlll
failsafe will set all channels to a predefined value until either, power is removed or
it regains signal. If a channel is set to off it will remain in the last position it was in
when signal is lost.
P‘JeSA'N
I“ I"
II? I“
“III LII! HIM “E
All!
Setup :
This function only works with 6 channels with an adjustment range from -100-100%.
1. Use the NaviKey to select the [F.SAFE] menu, then press the Navikey to enter
the function.
2. The screen will display [ST] and [OFF]. Rotate the Navikey to select a channel 3 OFF
then press the navikey to confirm.
3. Move the selected channel to the desired position using its' control input and
press the Navikey to save.
4. Repeat for other channels as needed.
Iligilal Pronorlional Radio control System FS-GTE
6.11 cran (CRAW) mum unn£| m m
This function is used to create a crawler mix, meaning that the front and back wheels slll-Tli nlli II! II:
can move in different directions. By default this function is set to off. Channel 3 will um um “I“ we
always be assigned as the rear wheels.
Setup :
[A]: Front wheel steering.
[B]: Rear wheel steering.
[C]: The front and back wheels will turn in the same direction for tight turns.
[D]: Front and back wheels will move in opposite directions. llllllll
1. Use the NaviKey to select the [CRAW] menu, press the Navikey again to enter
the function. OFF
2. Use the NaviKey to choose [A]~[D] or OFF.
3. Press the Navikey to confirm selection.
The following table shows the available modes:
[A1 A; I [C1
[B] B; I [D1
6.12 S.V.C. (SVC)
Note: This function is only available for the FSfBSG. However because of frequent
updates this function may become available for other receivers. for more information “W“ W“ m "I
please visit our website. sllI-Tn lull ll! Ali
Intelligent vehicle control needs the use of the receivers gyroscope. Using the "I". m“ ”m “e
gyroscope this function Will alter throttle and steering in order to keep the model
going in the desired direction. SVC UN
90
HH
Neu.CaI(NeutraI Calibration)
Calibrates the gyro settings so that the the intelligent vehicle control system is able
to set a current position for the netrual steering position.
This calibration will happen each each time the steering returns to this position in
order for the system to detect any direction change that is not desired by the user. ON
Rev (reverse)
Used to switch the orientation of the wheel in the intelligent control direction, Turn the vehicle body before
moving the vehicle to see if the direction of the wheel correction is correct. Turn left when the wheel should be
corrected to the right;
When turning to the right, the wheel should be corrected to the left.
FLY SKY
St.Gain (direction sensitivity)
Used to correct the wheel in the expected direction of travel, the system detects the body will rotate, it will
automatically through the wheel correction body. The direction sensitivity is the adjustment system for the
wheel of the school is the intensity of the set range of 0% -100%, when the vehicle running when the direction
of the left and right swing can reduce the intensity, correction strength is insufficient to increase.
Th.Gain (throttle sensitivity)
When the vehicle turns, the weak speed is too fast, may cause flicking or rollover. After the opening function,
the throttle trigger is not loose, the system will reduce the throttle, so that it can quickly and safely turn.
Deceleration is 0—100%.
Prio (priority)
The priority is used to set the correction ratio of the direction sensitivity when the vehicle is turned, that is, the
turning radius. When you hit the hand wheel to the maximum travel turn, the value is 0, the turning radius of
the most large, when the value is 100% the minimum turning radius.
Setup: [MODEz ON/OFF]
On/Off
1. Use the NaviKey to select the [SVC] menu, press the Navikey again to enter the function.
2. Move the Navikey to select SVC.ON, then rotate the Navikey so that the function shows ”ON" in the bottom
right corner.
3. Press the Navikey again to confirm,
[Neu.CaI]
Hllllll “I! I“ l I?!
1. Use the NaviKey to select the [SVC] menu, press the Navikey again to enter the sun-"i IIII up n;
functlfln- mu mt! um I“
2. Move the Navikey to select Neu.CaI. Neu.Cal
3. Make sure everything is centered and press the Navikey again to start
calibration.
CAL 1B...
[Rev]
1. Use the NaviKey to select the [SVC] menu, press the Navikey again to enter the Sill-H I"! ll!
function. Tnlll mt! mm in
2. Move the Navikey to select Reverse and press the Navikey to confirm.
Reverse
3. Rotate the Navikey to change between NOR (Normal) and REV (Reverse) as
required.
4. Press the Navikey to confirm.
FtE‘lir
Iligilal Pronorlional nadio control System FS-GTE
[SLGain]
mum mill m m
1. Use the NaviKey to select the SLGain menu, press the Navikey again to enter ill-"l "ll ll? I“
the function. um um um sue
2. Rotate the Navikey to change the St.Gain vaiue (%).
_ , St Gain
3. Press the Navukey to confirm.
50x
lllllll "I“ I“ "I
[Th.Gain] m-rn m m m
mm mm mm m
1. Use the NaviKey to select the Th.Gain and press the Navikey to confirm.
2. Rotate the Navikey to change the Th.Gain value (%).
3. Press the Navikey to confirm. Th Gain
50x
[Priority] mm mu m m
sun-Tn m m m
1. Use the NaviKey to select the Th.Gain and press the Navikey to confirm.
null mi! mum ll:
2. Rotate the Navikey to change the Th.Gain value (%).
3. Press the Navikey to confirm.
Priority
[135
FLY SKY
7. Product Specifications
This section contains FS-GTS transmitter and FS-BSG receiver specifications.
7.1 Transmitter specification(FS-GT5)
Model Type Car, Boat
Output channel 6
RF Range 2408—2475 GHZ
Channel spacing SODKHZ
Channels 135
RF Power <20dBm (for Europe)
Receiving Sensitivity -95dBm
2.4GHZ Protocol AFHDS 2A
Modulation Type GFSK
Transfer Method FHSS
Channel Resolution 4096
Channel Delay < 15ms
Low Voltage Alarm AA batteries <4.4V, ZS lithium battery <7.4V
Data Output None
Charging Port None
Antenna 26mm
Input Power None
_ NTN semi-permeable, segment screen, VA52.5 * 34mm LCD white
D|sp|ay .
backllght
Online Update N/A
Range (No ground interference) > 200m
Working Current 100 ~120mA
Channel Data Parameters Median: 1500us, Range: 900 ~ 2100us
Dimensions 15B*95*243 mm
Weight 2969
Certification CE, FCC ID : N4ZGT500
7.2 Receiver Specification(FS-BSG)
The FS-BSG has a built-in gyroscope stabilization system.
Channels 5
RF range 2.408-2.475 GHZ
RF channel 135
RX sensitivity 795dBm
2.4GHZ system AFHDS 2A
RF Power <20dBm (for Europe)
Modulation type GFSK
Power input 4.0 - 8.4 V DC
Weight 7.659
Dimensions 29mm x 22mm x 16 mm
Certificate CE) FCC ID : N4ZBSGOO
Iligilal Pronorlional nadio control System FS-GT5
8. Package Contents
hem Quantity
‘c
Transmitter FS-GTS 1
Receiver FS-BSG 1
mm...
mum
Quick Start Quide 1
FLY SKY
9. Certification
9.1 DoC Declaration
Hereby, [Flysky Technology co., ltd] declares that the Radio Equipment [FSfGTS] is in compliance with RED
2014/53/EU.
The full text of the EU DoC is available at the following internet address: www.flysky-cn.com
9.2 CE Warning
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-Iocated or operating in conjunction with any other transmitter. End-users
and installers must be provided with antenna installation instructions and transmitter operating conditions for
satisfying RF exposure compliance
9.3 Appendix 1 FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or televison reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly approved by the party responsible
for compliance could void the user' s authority to operate this equipment,
This equipment complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user authority to operate the equipment.
1. Move all your channels to the desired position.
2. Select [All channels] and then [Yes] in the confirmation box.
fl
Iligilal Pronorlional nadio control System FS-GT5
10. Environmentally friendly disposal
Old electrical appliances must not be disposed of together with the
residual waste, but have to be disposed of separately. The disposal
at the communal collecting point via private persons is for free. The
owner of old appliances is responsible to bring the appliances to
these collecting points or to similar collection points. With this little
personal effort, you contribute to recycle valuable raw materials and the
treatment of toxic substances. _
CAUTION
RISK OF EXPLOSION IF BATTERY lS REPLACED BY AN INCORRECT TYPE.
DlSPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS
FLY SKY
www.flysky-cn.com
Copyright ©2017 Flysky Technology co., ltd
Release date: 2017—12—27
E C E FCC ID: NAZGTSOO

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2017:12:27 18:09:57+08:00
Creator                         : Adobe InDesign CS6 (Windows)
Modify Date                     : 2017:12:27 18:10:07+08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Metadata Date                   : 2017:12:27 18:10:07+08:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Document ID                     : uuid:9dad5ed2-7b9c-401e-82d8-14c58cc444f0
Instance ID                     : uuid:8de16d74-a45a-4dec-8384-ad83e5fd11fb
Producer                        : Adobe PDF Library 10.0.1
Page Count                      : 12

EXIF Metadata provided by EXIF.tools