FRIGIDAIRE Dishwasher Manual L0103238

User Manual: FRIGIDAIRE FRIGIDAIRE Dishwasher Manual FRIGIDAIRE Dishwasher Owner's Manual, FRIGIDAIRE Dishwasher installation guides

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadFRIGIDAIRE  Dishwasher Manual L0103238
Open PDF In BrowserView PDF
Dishwasher

Parts You Will Need*
•
•
•
•

Installation
Instructions

IMPORTANT:

Drain Hose Clamp, 1'/," Diameter (included)
Elbow, 90 ° with a %" National Pipe Thread (not included)
Strain Relief Bushing (not included)
Wire Nuts, two (2) for 12-14 gauge wire (not included)

If required:

Available

• '_("Branch Tailpiece and
Connector Kit (See Step 4)
• Air Gap Kit (See Step 4)
• Fastaners for floor

Plumbing Supply Store

Electrical

1.

Make sure your location has the right drain, water, and electrical
outlets to make the connections. Do not instafl unit under a
cooktop range. Damage to plastic tub will occur.

0

34V4" _

•

Examinedishwseherandlocateconnectlons.

•

Locete dishwasher where there is easy access to drain, water,
and electrical lines. The best location is on either side of the

24"

SeeStep4.

•

Kinked water or drain hoses can cause problems. Do not
remove drain hose from tub attachment. See Step 6.

•

Dishwashers need to be connected to a hot water supply with
enough water pressure to insure an adequate fill. See Steps 4
and 7.

•
Printed in U.S,A.

154397801
(01/01)

•

before

installing

dishwasher•

Each home installation differs. You will need additional parts
Ilated above to complete your installation. See S_ps 4 and 7.
Flush water line prior to making the final connection to
prevent clogging of dishwasher's filter screen. See Step 7.

• Anchorthedlshwashertocountertop.

Do not use dishwasher until completely installed.

shaded

1.

Determine where you will connect to hot water supply, Review
Figure 3 and note the location of water inlet valve.

3.

If you connect to a sink trap, local codes may require you to
instalr an air gap kit, not included. The drain hose will be routed
from dishwasher to air gap inlet as shown in Figure 6. An air gap
kit is available from a plumbing supply store.

Property Damage

4.

If you connect to a disposer, the large end of drain hose will fit.
Figure 7(a). The knock out plug must be removed from
inside disposer inlet before making the final fit to drafo hose.
See Figure 7(b).

0

area.

6"

Remove two (2) screws at front of the kickpiate assembly
using a #2 Phillips screwdriver.

2.

Tilt and pull forward to remove, (Figure 1).

2.

Be sure water inlet valve is protected from freezing. If valve
freezes and ruptures, flooding may occur.

3,

Determine amount of tubing needed to connect hot water supply
to the unit's water inlet valve. Copper tubing must have a
minimum %" OD. High-pressure and high-temperature rated
plastic tubing with a minimum Inner diameter of %" may be
used. A shut-off valve installed outside dishwasher cabinet is
best• See Figure 4.

_

24"

1

2.

Remove any carpet from area to provide motor clearance. Floor
should be flat and free of any obstruction.

IMPORTANT: Drain, water, and electrical lines should be
roughed-in before going any further.

Dishwasher
Drain Hose

Electric Shock Hazard
Electrical, water, and drain lines must be confined
to shaded areas to prevent damage to electric
conductors, water, and drain lines. See Figure 2.

NOTE: If dishwasher is installed at end of a cabinet line, sides
and back must be fully enclosed•

4.

Cut water access hole in shaded area in Figure 2

5.

Route water supply line into installation area.

IMPORTANT:
Incoming hot water temperature should be et
least 120°F (49°C). water pressure should be between
20-120 psi.

1.

Review Figures 5 and 6 to see the different ways to connect
dishwasher to drain system. Choose method that best suits your
Reed.

2,

If you connect to s sink drain, entry will need to be above trap.
A "Y" branch tailpiece and connector kit, not included, will make
this method easier and includes all needed fittings and
instructions, See Figure 5.

Assembly

Water Inlet
Drill, Electric

Valve

_

_

Boaom Screws

Figure

Tape, Measuring
Wire Stripper or Utility Knife
Wrench, Hex-end
Wrenches, 2 Adjustable (for copper tubing)
or 2 Pipe Wrenches (for iron pipe plumbing)

All connections must be made in shaded area in Figure 2.

3.

Locate water inlet valve behind kickplete on bottom left underside
of unit. The valve has a 3/8"NPT female fitting.

4.

Wrap 90° elbow (not included) with pipe thread tape (or apply
joint compound) and thread it into water inlet valve.

5.

drain,

Do not remove drain hose from side of unit.
Figure

I
L_ft Side

Safety Glasses
Saw, Keyhole or '/2", 1_/2" to 2" Hole Cutters
Screwdrivers, Slotted and #2 Phillips (magnetic tip
preferred)
Tape, Electrical or Duct

2.

/

Level
Pipe Thread Tape (for sealing threads)
Pliers

Review dimensions in Figure 3 to locate dishwasher's
water, and electrical connections.

IMPORTANT:

Driver, Socket 3/16", 1/4",_t16"
Flaring Tool / Tube Cutter (for copper tubing)
Flashlight
Gloves
Pipe Joint Compound (for iron pipe plumbing) or

Locating the Connections
1.

3

Front

Right Side

49 V4"
Door in
open position

Tighten elbow with a wrench, leaving elbow pointing toward rear
of unit. To prevent bending of bracket or breaking of valve, avoid
overtightening.

From rear to
center of water
inlet valve,

3%"
From floor to
water inlet
valve.
Junction Box
(not visible)

_- 17%"
From _or to
junction box.
Drain Hose

5.

Before cutting drain hose access, check both sides of selected
area to avoid interference. Cut a 2" diameter hole in shaded area
shown in Figure 2.

6.

If the cabinet wall is wood, sand edges of hole until smooth and
rounded, If cabinet wall is metal, cover all sharp edges with
electrical or duct tape to avoid cutting drain hose,

Figure 4

DraIn

Kickplate

E ilre --

IMPORTANT: For proper operation and appearance of unit,
cabinet opening should have dimensions as shown In Figure 2.
If unit is to be placed in a corner, there must be at least a 2-Inch
side clearance to open door,

IMPORTANT: Do not cross drain, water, and electrical lines in
front of dishwasher motor or frame.

Needed for

Larger end_/_se

Figare2

Failure to follow this warning can result in serious injury.

Tools and Materials
Installation

_

I/Z, '

It is not necessary to remove the outer door for installation.
However, you might find it more convenient to do so. You
can find directions for removing door in Step 10.
Kickplate

DmL_

6"

] ]/2"

SeeStepg.

1.

Do not push down on open door.

Water

DO not use the furnished drain hose or a rubber garden bose
for the water supply line. Either of these hoses can burst.
Flooding may occur and cause property damage.

Failure to follow these instructions could result In
fire or electric shock.

NOTE:

Pull electrical cable through hole into installation area.

@

For your safety, please read and observe all safety instructions.
This guide will help you anticipate drain, water, and electrical
connections, and help you select the best Iocabon for the dishwasher.

Tip Over Hazard

4.

tv-,_

• The dishwasher will look, sound, and perform best when
properly leveled• See Step 5. (NOTE: If levelers are removed
during installetlon, make sure the floor is flat and free of any
obstruction•)
Read all instructions

Cut access hole in shaded area shown in Figure 2.

water,

7112 ,,

• A 15-20 amp, grounded, 120 volt AC only, etactrical supply is
required. See Steps 4 and 8.

OWNER: Read your dishwasher Use and Care Manual. It contains
important safety information for operating this appliance. ]t also has
many suggestions for getting the best results from your dishwasher.

3.

fftln

Electrical, water, and drain connections are not the same for
all age, brands, or models of dishwashers. Check the location
and length of home utilities. See Step 4.

If dishwasher drain hose will be connected to a food disposer
for the first time, knock out plug located inside disposer inlet.
See Steps 4 and 6.

Electrica_

and drain lines
mast be confined t_

kitchen sink for access to existing plumbing and ease in
loading dishes. See Step 4.

INSTALLER: Leave Installation Instructions with owner.

Note the locations of electrical supply and dishwasher's electdcat
junction box on right underside of unit behind kickplata assembly.
See Figure 3.

90°-

0

•

2.

_f

Shock Hazard

Disconnect electrical power at the fuse box or
circuit breaker box before beginning installation.
Failure to follow this warning could result in death
or serious Injury.

•

The dishwasher operates on a 120 volt, 60 Hz electrical supply.
Provide a separate circuit with a fuse or circuit breaker rated for
at least 15 amps (20 amps if connected to disposer) but not more
than 20 amps,

g could result

anchoring (See Step 9)

Air Gop _

1.

at:

Plumbing Supply Store
Hardware Store

Electric

Disconnect power before starting Installation.

I

1.

l

I Figure

Measure height of cabinet opening
from underside of counterlop to floor.
Check chart for height opening and
suggested adjustment•

Leg Leveler Adjustment
Height of
Cabinet Opening

Electrical Supply

Floor Anchoring

1,

Remove junction box cover and pull house wiring into junction
box. Sea Figures 12 and 13,

This procedure is difficult and should be used only if countertop
mounting brackets cannot be used.

2.

Use a UL listed strain-relief bushing, not included, at box to
stabilize wiring,

1.

Screw W'lag screws, not included, through holes provided in
frame rail. See Figure 15.

2.

Use expansion fasteners if floor is concrete.

10

IMPORTANT:
dishwasher's

Be sure electrical cable is not routed behind
motor.

IJ_e

3.

Chart

Number of Turns to
Adjust Levelers

34" (86.4cm)

0

34Ve" (86.7cm)

2

345h8" (87.2cm)

6

34V2" (87.6cm)

9

Note: Do not remove

hose from attachment.

Side View

Property Damage
Do not solder within 6" of the water inlet valve. Damage to
the plastic parts In the valve may occur.

Be sure the dishwasher is placed where the water inlet valve
will be kept from freezing. If the valve freezes, it may rupture
and flooding may occur.

Water Line
1.

Figure 12

3.

Inside junction box, attach ground wire under head of grounding
screw and tighten. See Figure 13.

4,

Connect incoming black lead to dishwasher's black lead and
incoming white lead to dishwasher's white lead with wire nuts or
other suitable connectors, not included. Wire nuts should be tight.

5.

Replace junction box cover. See Figure 13.

Flush water line before connecting it to water inlet valve to
prevent early clogging of filter screen. Place a bunched towel
over end of line to prevent splashing. Open valve for a few
seconds and let water drain into a pan Turn off water supply
at shut-off valve.

Figure

Rear Leveler

6.

Metal color panels are sharp and should be
handled with care. Wear gloves to protect hands.

Grout_dWire

Failure to follow this warning may result in injury.

If levelers have to be removed, make sure floor is free of
obstructions.

5.

Place dishwasher inside cabinet area so that it is centered in
opening. Use caution when moving dishwasher to prevent
damage to dishwasher, floor, and cabinets.

Through
Wall
White Wire to
White Wire
(Neutral)
Black Wire to
Black Wire

Througi
Cabinet

7.

Check that dishwasher is level from front to back by placing level
on side of opened door. See Figure gb.

8.

Adjust levelers up or down until dishwasher is level.

Unlatch and open door. Using a Phillips head screwdriver,
remove two (2) screws from inner door. Save screws to
reassemble. See Figure 16e.

Junction
Box Cover

Replacing Door
Figure

Through
Floor

Figure 9b

2.

Route water line to water inlet valve as shown in Figure 11.

3.

While firmly pulling water supply line into 90 ° elbow, tightly
connect water supply to water inlet valve. Supply line must be
free of kinks, scales, chips, and lubricants.

4.

Turn on water supply and check for leaks.

5.

If water inlet valve clogs, make sure water supply is off. Remove
four (4) screws at inlet end of valve and clean filter screen.

13

The dishwasher must be secured to keep it from tilting when door is
opened• Choose one of the methods described below to secure unit.

\

Countertop Anchoring
1.

Adjust levelers (see Step 5) so mounting brackets touch
underside of countertop. IMPORTANT: Dishwasher must rest
on floor--do not hang from countertop. See Figure 14.

2.

Screw mounting brackets firmly to countertop using screws
provided in literature packet.

3.

Open and close dishwasher door slowly. If door hits mounting
bracket screw heads, adjust front levelers.

\

\

Close and latch door while holding both sides.

3.

Place one hand on each side of door and puff down at top
approximately 1/4". Pull entire door assembly toward you to
remove. See Figure 16b.

Figure 16b

Make sure electrical power has been disconnected at fuse box
or circuit breaker box.

2. Secure drain hose to sink drain, disposer, or separate trap with a
clamp. IMPORTANT: Be careful not to overtlghten clamp or you
may damage end of hose. Do not connect hose to hodzontal pipe
between sink drain and disposer.
3. Be sure unit does not rest on drain hose. It should be free of
elect deal components and door spdngs. Do not cut corrugated
drain hose. Pull excess through cabinet and place under sink.
Make sure hose does not come in contact with any sharp edges.
See Figure 10.

Adjust door springs to balance weight of door, A correct spring
setting allows door to remain horizontal in opened position, yet
will rise to close with slight lift fo finger.

3.

If necessary, increase tension by moving springs to a hole toward
rear of unit or decrease by moving them toward front. See Figure
17.

Figure 17
Move s rings toward
rear o_ishwasher to
increase tension.

4.

Turn electhcal supply on.

_s

Head Screw_
#8 x %" (included in the
literature?ackep.
Figure 14
Electric Shock Hazard
If all connections are correct, there are no leaks,
and unit runs properly, replace the klckplete
assembly before placing unit into operation.

All wiring connections must be enclosed in the junction box.

Do not use an extension cord. Such use can result In fire,
electrical shock, or other personal injury.
Failure to follow these instructions could result in death or
serious injury,

2.

E3 At first fill, make sure water completely covers filter surface.
(Motor pump sound may be heard before water enters unit).
[3 At pump-out, make sure all water is pumped out.
[3 Check water connections again for leaks.

Do not connect the dishwasher to the power supply until the
appliance is permanently grounded.
Joining aluminum building wire to stranded copper wire
should be done by a qualified electrician using materials
recognized by UL and local codes. This unit has copper lead
wires.

Refer to Step 10, numbers 5 and 6, for replacing outer door.

Operate the machine through at
least one fill and pump-out,
checking the following items:

Electric Shock Hazard

The dishwasher must be connected to a grounded metal,
permanent wiring system. The equipment-grounding
conductor must be run with the clreult conductors and
connected to the appliance's equipment grounding terminal
or lead, It Is the consumer's responsibility to contact a
qualified Installer to make sure the electrical Installation
conforms with the National EleCtrical Code and local codes
and ordinances,

1.

I

2.

Note: Open and close door to make sure it does not hit
surrounding cabinets or countsrtop.

I. Pull out unit and move back in place while routing drain hose
through access hole. Use caution to prevent damage to the
dishwasher, floor and cabinets. IMPORTANT: Make sure there
are no sharp bonds or kinks that might restrict drain flow.

[3 All packing materials and consumer literature have been
removed from unit.
13 Dishwasher is level and securely fastened•
[3 Open and close door to make sure it does not hit surrounding
cabinet or countertop.
[3 Water and drain lines have no kinks.
O Wiring connections to junction box are tight.
Ci Water supply is turned on.
[3 Joints am free of leaks.

Figure 16a

Check that dishwasher is level from side to side by placing a
level against the top front section of the tub. See Figure 9a.

i

Before starting the dishwasher,
check these items:

To Remove and Replace Outer Door

11

1.

4.

Unlatch door and open while supporting outer door on both sides
at bottom to keep in place. Align screw holes and replace screws.

Cut Hazard

Wrench--

Figure 8

Door

Junction Box
(in place)

Loosen the front and rear leveling legs by turning
counterclockwise. Refer to chart for number of turns. See
Figure 8. Front levelers should allow V4"below underside of
countertop,

Figure 9a

Scrgw$

Figure 15

Use care that no sealer, dirt, or other objects enter the valve.
Damage to the filter screen may occur.

6.

Figure 16c

Through
Cabinet

Through
WaX

Move dishwasher to front of installation area.

FrontLeveler

[_

door is flat. Push up from bottom until there is no gap between
door and control panel. See Figure 16c,

(.otiocP' Y)

For additional height add shims under levelers.
2,

t/4"

ready to replace door, fit the slots on each side of top door
5. When
edge over the tabs on the metal liner. Push on sides to insure the

Failure to follow this warning could result in
electric shock,
4.

Place door where it will not get scratched or damaged while
completing installation.



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Mon Apr 02 14:42:23 2007
Author                          : 
Title                           : 
Subject                         : 
EXIF Metadata provided by EXIF.tools

Navigation menu