Fanimation CE10207 Ceiling Fan Remote Controller User Manual

Fanimation, INC Ceiling Fan Remote Controller

user manual

CEILING FAN REMOTE CONTROLLEROPERATION AND INSTALLATION INSTRUCTIONS(Please keep this instruction pamphlet.)IMPORTANT POINTS TO REMEMBER:1.Read and save these instructions.2.Please note that all fixed wiring appliances should be installed by a qualified electrician.3.The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall switch.4.Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.5.Install receiver into the ceiling fan canopy of the fan to ensure proper protection.6.This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only.7.Do not install in damp locations or immerse in water. (For indoor use only.)8.Do not pull on or cut leads shorter.9.Do not drop or bump the unit.10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this willdamage the transmitter. Dispose of used battery properly, and keep the battery out of reach of children.11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wallcontrol.INSTALLATION INSTRUCTIONS1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the “Light Switch” afterinstallation.2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy comes upto cover the receiver and bracket.LEARNING PROCESS1. This unit finished learning process inside manufactory, if replace transmitter or receiver, user need to redo learningprocess before using this unit. Receiver could remember up to 5pcs transmitter.IMPORTANTYOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHTKIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
2. After installing the unit and power on, open battery cover (with battery, DC12V/A23 1pc, installed) and press anduse a ball pen to hold ”LEARNING” key 1~3seconds, FAN will be turn off and the turn to medium speed, whichindicate that learning process finished. Learning effect distance is same with remote’s. Please note that must pressthe “LEARNING KEY” within 60sensonds after power on. If just replace batteries, no need to re-learn.3. Please note that the transmitter can learn in multiple receiver, when doing learning process please make sure notlearn in other receiver. Suggest to separate power switches of fans in 2 meter range.LIGHT FUNCTION SELECT SWITCH1. If installed energy light onto ceiling fan, please slide the “light function select switch” to on/off position. If installedtungsten light onto ceiling fan, please slide the “light function select switch” to dimmer position.2. Light load: 190W (Max.) If overload, the receiver will cut off light power automatically. Please change the light load.FUNCTIONS OF TRANSMITTERLIGHT : ON/OFF- Press and release immediately to turn on or off the light.DIMMER-Press and hold to dim or brighten lightto the desired level and release.(Tungsten only and light function select switch on dimmer position.)FAN OFF : Turn off the ceiling fan.HI :Turn on the fan at high speedMED :Turn on the fan at medium speedLOW : Turn on the fan at low speedFEDERALCOMMUNICATIONSCOMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connectthe equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer oran experienced radio/TV technician for help.CAUTION:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority tooperate the equipment.FCC ID：2ABGUCE10207This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.To assure continued FCC compliance:TRANSMITTERLEARNING KEYInstallation of TransmitterWall Mount Holder with twoscrews.LIGHT FUNCTIONSELECT SWITCH
Exposure to Radio Frequency Radiation: To comply with FCC RF exposure compliance requirements, a separation distance of at least 20cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu