Fego Precision Co TP38 Transmiter User Manual RL168

Download:
Mirror Download [FCC.gov]
Document ID	3770174
Application ID	xHaWEQLbhWQy8jnSXjKPDw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	141.7kB (1771256 bits)
Date Submitted	2018-03-06 00:00:00
Date Available	2018-03-27 00:00:00
Creation Date	2017-08-25 11:47:56
Producing Software	Corel PDF Engine Version 18.1.0.661
Document Lastmod	2018-02-27 17:29:46
Document Title	RL168 說明書.cdr
Document Creator	CorelDRAW X8
Document Author:	user

Continuously Variable Speed Fan Controller
Model: RL-168
SAFETY PRECAUTIONS
Please observe the following general safety precautions carefully
before and during all phases of handling, installation, removal,
operation and maintenance of this product. Failure to comply
with these precautions violates safety standards of design,
manufacture and intended use of the product.
We assumes no liability for customer’s failure to comply with these
requirements.
SAFETY WARNINGS
1. Read all instructions and safety information. Review assembly
diagrams provided before installing your new ceiling fan.
2. This remote controller must be installed according to local
authority regulations.
3. This product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
Model：TP-38
POWER:AC 120V~240V 50 / 60 Hz
FCC Compliance Statement:
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,and (2) This device
must accept any interference received, including interferencethat may
cause undesired operation.
CONGRATULATIONS ON YOUR CHOICE
Thank you and we are delighted you have chosen a Continuously
Variable Speed Fan controller for your home please read all
instructions carefully before assembly and use.
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
4. Young children should be supervised to ensure that they do not
play with the appliance.
5. All electrical works must only be undertaken after disconnection
of the power by removing fuses or turning off the circuit
breaker, to ensure all pole isolation of the electrical supply.
6. Do not use outdoors where it could be exposed to water or
moisture.
7. This product is for indoor use only.
8. This product requires 120~240V, 50~60 Hz Vac 60Hz power supply.
9. This product is to be used only for controlling a ceiling fan with
an A.C. (Alternating Current) motor.
10. The remote controller receiver must be earthed during
READ BEFORE INSTALLATION
1. Power supply to input wires of remote controller receiver must
be connected through an isolation switch (e.g. wall switch).
2. Install remote controller receiver inside ceiling fan canopy to
ensure proper protection.
installation.
11. Do not pull or cut short lead wires.
12. Do not drop or bump the remote controller set.
13. Do not use this remote controller in conjunction with any
variable (rheostat) wall controller.
14. Do not use the remote controller transmitter (handset) with
any other receiver.
3. Set ceiling fan speed control rotary switch (if any) to HIGH
setting and control switch for light kit (if any) to ON position
before operating remote control functions.
4. For ceiling fan with pull chain switches, set pull chain switches
accordingly so that ceiling fan speed setting is at HIGH and fan
light setting (if any) is at ON position before operating remote
control functions.
15. Keep battery out of reach of children.
16. This manual is not intended to instruct or assist untrained or
unqualied persons to install this remote controller.
17. It is the responsibility of qualied, licensed installer and user to
5. Battery will weaken over time and should be replaced before
leaking takes place as this will damage the transmitter. Dispose
of used battery properly.
6. If remote controller is to be used for controlling a ceiling fan
apply common sense and care at all times during installation
(i) with a low prole (hugger) design, or (ii) that has a smaller
and operation.
hanging bracket, then you should make sure the hanging
bracket will t remote controller receiver. Otherwise, if the
receiver cannot be inserted into the hanging bracket due to
dimension limitations or because there is no hanging bracket
as may be in the case of a low prole (hugger design) ceiling
INSTALLATION INSTRUCTIONS
※ Make sure electricity is turned off at the main power box
fan, then the receiver can be enclosed in an Electrical
Insulation Box (installation must comply to Australian wiring
regulations) and placed in the ceiling. Electrical Insulation Box
before commencing work. Turn off the power by removing fuse
is not supplied. In this case, remember to draw the antenna /
or turning off circuit breaker before installing remote controller.
aerial wire away from the insulation box through a small hole.
HOW TO INSTALL REMOTE
CONTROLLER ID CODE LEARNING
Each transmitter (handset) of RL-168 remote controller carries
a unique Identity Code (ID Code) to facilitate communication
between paired devices. The ID Code is set by factory and is not
user changeable. The length of ID Code allows up to a million
different code combinations, enabling independent control of
multiple fans installed within a close proximity. A remote receiver
must undergo an “ID code learning” process before it recognises
and can communicate with the remote handset but this process
had been completed in the factory so you can start using the
remote controller once electrical installation is complete.
However, you will be required to perform an “ID code learning”
process manually under these circumstances:
• When you have multiple fans installed within a close proximity
and want to control all fans using a same remote transmitter.
Note: Each fan requires its own receiver
• When your remote controller is not responding (make sure
battery is not at)
• After you have replaced a faulty transmitter or receiver with a
new one.
Otherwise the remote controller will not work. To perform this
process manually, follow below steps:
INSTRUCTION: After turning on the AC power to the remote
receiver, press and hold the transmitter “MODE” button for 5
seconds until the receiver beeps to indicate the code learning
process had been completed. This operation must be completed
within 1 minute after turning on the AC power.
operate the ceiling fan and light. If the fan is not responding to
the transmitter, turn off the power to the receiver and repeat
the INSTRUCTION.
2. Check that battery is installed.
3. Remove the battery if not used for long period of time to
prevent damage to the handset.
1. Make sure power supply
is cut off before removing
fan canopy
Mounting
Bracket
Ridge
Ball Groove
2. Think about best
orientation of remote
receiver inside fan
canopy. Connect
receiver’s input
and output wires in
accordance to wiring
diagram provided. Note:
Isolation switch must be
installed.
Wire connection,
see picture below.
Old Receiver
Mounting
Bracket
Receiver
Hanging
Bracket
3. Tidy up wires and re-install
fan canopy. Make sure
not to break any wire
connection.
Canopy
NOTE:
1. After completing the steps above, you should be able to
Deco Ring
FUNCTIONS
FAN CONTROL
ON/OFF: Toggle fan on or off
• When Normal mode is activated, you
can manually control and set the fan
speed
SPEED: Press once of ▲High or ▼low to
increase / decrease fan speed. There
are eight (8) fan speeds. Press and hold
of ▲High or ▼low to increase / decrease
fan speed by 1% from 25% to 90%
MODE: Press button to choose between
Normal, Breeze, Sleep, Delay, Timer off 1,
3, 6 Hours mode.
• When Breeze mode is activated, the
word BREEZE appears on screen. The
fan speed is auto-regulated by program generating comforting
winds
• When Sleep mode is activated, the word SLEEP appears on
screen. From the initial speed, that is the set speed when this
function is activated, the fan speed automatically steps down
one 1% every 8 minutes until it reaches the 50% speed of
starting sleep speed.
• When the Delay mode is activated, the word Delay appears on
screen and will turning off the fan and light after 2 minutes.
• When the Timer off mode is activated, the word Timer appears
on screen and will turning off the fan after 1,3 or 6 hours.
LIGHT CONTROL
ON/OFF: Press once to toggle fan light on or off.
Note: Replace batteries when battery symbol is shown.
Making electrical wire connection
Follow diagram below and make sure that all exposed wires are secured inside wire
nuts or terminal block.
Note : Wires from house may vary in color and may not include ground wire ( green ).
*White wire from house to white wire from fan
*Black wire from house to black wire from fan
*Ground wire from house to green wires from downrod and from mounting bracket
*Secure with twist - lock wire nuts (provided from hardware bag)
*Gently push wires into junction box with wire nuts pointing upward.
White
From House
From Fan
(AC-N)
(MOTOR-N)
(AC-L)
(MOTOR-L)
White
Black
Black
Green
Green
( from downrod )
( for ground wire )
( from mounting bracket)
Fig 1.
Green

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : user
Create Date                     : 2017:08:25 11:47:56+08:00
Modify Date                     : 2018:02:27 17:29:46+08:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : user
Title                           : RL168 說明書.cdr
Creator Tool                    : CorelDRAW X8
Metadata Date                   : 2018:02:27 17:29:46+08:00
Producer                        : Corel PDF Engine Version 18.1.0.661
Document ID                     : uuid:baf77474-c19b-43de-b61b-8ed5d632ae21
Instance ID                     : uuid:cbe581e5-51cc-40c6-b655-7d8298119484
Page Count                      : 2
Profile CMM Type                : Linotronic
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : Hewlett-Packard
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : Hewlett-Packard
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)

EXIF Metadata provided by EXIF.tools