Fender Musical Instruments FMAPR4400 WIFI+BT Module User Manual 15 F23BUUM13 W2 UserMan r2

Download:
Mirror Download [FCC.gov]
Document ID	3304714
Application ID	7OlgkZUpOeobIFhsJFbCPA==
Document Description	15_F23BUUM13-W2 UserMan, r2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.3kB (316262 bits)
Date Submitted	2017-03-06 00:00:00
Date Available	2017-03-06 00:00:00
Creation Date	2016-11-02 11:20:41
Producing Software	Acrobat Distiller 9.3.3 (Windows)
Document Lastmod	2017-03-06 10:51:39
Document Title	Microsoft Word - Fender FMA WIFI-USB-FTSW Manual Rev1.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

WIFI+BT Module
F23BUUM13‐W2
Manual and Spec, revision 1.0
Reference Documents


FN‐LINK F23BUUM13‐W2 module product specification
FMA WIFI‐FTSW‐USB schematic
Description
The Fender FMA WIFI‐FTSW‐USB PCB Assembly is an I/O board (WIFI board) used in the family of
Fender Modular Architecture (FMA) products. The board has a USB port with a micro AB connector, a
Fender Footswitch port with a ¼” phone jack and a wireless module.
Circuit Description
Referring to the block diagram, there are three main sections of the circuit:



FN‐Link F23BUUM13‐W2 module
USB port
Footswitch port
Communication with the FN‐Link module is accomplished through a USB port from the 18‐pin main
board header. The WiFi and Bluetooth radio circuitry is contained on the FN‐Link module. There is no
antenna on the module so the radio output from the module connects to an F‐Type PCB antenna on the
PCBA. The FN‐Link module operates from a 3.3V supply source on the main PCB through the 18‐pin
header.
The USB circuit on the PCBA consists of ESD protection components and a micro AB USB connector.
The Footswitch circuit on the PCBA consists of ESD protection components and a ¼” phone jack
connector.
FN‐Link Module installation and Use
The FN‐Link module is soldered to the PCBA. Pads on the PCBA make contact to the 3.3V supply, USB
port and antenna. All communication between the host processor and the module is accomplished
through the modules USB port. A description of specific commands for Bluetooth and WiFi driver
development is beyond the scope of this document and can be found in documentation from Realtek
for the RTL8723BU WiFi+BT chip elsewhere.
Block Diagram
FMA Main PCB Interface Header
All control and power signals come from a connection to a mother board through an 18‐pin, 2mm dual
row female header. The pinout for the header is in the table below:
Pin
10
11
12
13
14
15
16
17
18
Signal
USB_OTG_DP
USB_OTG_DN
GNDD
FTSW_DAT
CHIP_WAKE
FTSW_DET
HOST_WAKE
USB_OTG_5V
USB_OTG_ID
3.3V
USB_WIRELESS_DP
GNDD
USB_WIRELESS_DN
reserved
reserved
reserved
reserved
reserved
Description
USB OTG port data signal
USB OTG port data signal
Digital GND
Footswitch port data signal
Reserved for future use
Footswitch port detect
Reserved for future use
Reserved for future use
USB OTG port ID signal
3.3V DC Supply
FN‐LINK Module USB port data signal
FN‐LINK Module USB port data signal
Reserved for future use
Reserved for future use
Reserved for future use
Reserved for future use
Reserved for future use
FN‐Link Module
WIFI board is uses an FN‐LINK F23BUUM13‐W2 module for wireless communication. The FMA main
board communicates to the module through a USB port. The wireless module is supports and number of
IEEE standards including IEEE 802.11b, IEEE 802.11g,IEEE 802.11n,IEEE 802.11d,IEEE 802.11e,IEEE
802.11h and IEEE 802.11i. TH module also supports Bluetooth specs including Bluetooth 3.0 and
Bluetooth 4.0 Dual mode. For a complete list of supported wireless standards please refer to the
product specification for the FN‐Link F23BUUM13‐W2 module.
Antenna
An F‐type PCB antenna is located on the PCB to support the 2.4GHz signal from the FN‐Link module, and
the maximum antenna gain is 1.0dBi.
Power Consumption
Operating Voltage
WiFi mode current
BT
Board Dimensions
3.3VDC +/‐ 9%
200mA (TX/RX continuous mode)
2.1 mA (idle power saving)
0.1mA (Idle or RF disable mode)
15mA (SCO HV3)
0.9mA (Inquiry and Page Scan)
7.5mA (ACL no traffic)
FCC Statement:
This de vice co mplies with Part 15 of the FCC Rules. Op eration i s subject to t he
following two conditions: (1) Th is device may not cause harmful i nterference. (2) Thi s
device must accept any interf erence received, i ncluding interference tha t may cause
undesired operation.
NOTE: This equipment has been te sted and found to comply with t he limits for a Class
B digi tal device, p ursuant to Part 15 of t he FCC Rules. The se limits are designed t o
provide re asonable protection against harmf ul interference in a residential installation.
This equi pment generat es u ses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a parti cular installation. If this equipment does cau se harmful interference to r adio or
television reception, which can be determined by turning the e quipment off and on, t he
user is encouraged to t ry to co rrect t he int erference by one or more of the following
measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not e xpressly approved b y the party responsible
for compliance could void the user's authority to operate the equipment.
LABEL OF THE END PRODUCT:
The final end product must be label led in a visible area wit h the following "Contains TX
FCC ID: 2AATL-F23BUUM13". I f the size of the end product i s sm aller than 8x1 0cm,
then additional FCC part 15.19 st atement is required to be avail able in the users
manual: This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interf erence received, i ncluding interference tha t may cause
undesired operation.
RF Exposure
This device has been evaluated and shown compliant with the FCC RF Exposure limits
under fixed exposure conditions (antennas are greater than 20cm from a person's body)
when installed in certain specific OEM configurations.
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. Due to missing shielding the module
is strictly limited to integration by the Grantee himself or his dedicated OEM integrator
under control of the Grantee. However, the OEM integrator is still responsible for testing
their end-product for any additional compliance requirements required with this module
installed.
IMPORTANT NOTE:
This device is intended only for OEM integrators under the following conditions:
(1) According to FCC P art 15 Subpart C Section 15. 212, t he radio e lements o f t he
modular trans mitter must have their own shieldi ng. However, due to th ere is no
shielding for thi s WIFI/ BT module, this module is granted as a Li mited Modular
Approval.
(2) This module has been designed to ope rate with PCBA antenna having a m aximum
gain of 1.0dBi.
(3) Integration is t ypically s trictly r estricted t o Grantee hims elf or dedicat ed OEM
integrators under control of the Grantee.
The m odule will be responsible t o satisfy SAR/RF Exposure requirement s, when the
module integrated into any (portable, mobile, fixed) host device.
This module is intended for OEM integrator only and the OEM integrators and instructed
to ensure that the en d user ha s no manual in structions to remove or in stall the device.
The OEM integrator is st ill responsible for the FCC compliance requirement of t he end
product, which integrates this module.
The module has no shielding and tested stand alone. This module is tested and
approved as Limited modular approval with stand alone configuration, any OEM
incorporated this radio module into any system are require additional testing and
evaluation.
The module is only certified with the installed antenna. Any change of the antenna will
void the certification.
IC Notice:
This device complies with Canada Industry licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference; and
(2) this device must accept any interference. Including interference that may cause
undesired operation of the device.
Avis d’IndustrieCanada
Le present appareil est conforme aux CNR d'industrie Canada applicables aux
appareils radio exem pts de licence L'exploitation est autorisée aux deux conditions
suivantes:
1) I'appareil ne doit pas produire de brouillage; et
2) I'utillsateur de I'appareil doit accepter brouillage radio électrique subi meme si le
brouillage est susceptible d'encompromettre le fonctionnement. Mauvais
fonctionnement de I'appareil.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclarationd'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This device and its antenna(s) must not beco-located with any other transmitters except
in accordance with IC multi-transmitte rproduct procedures.
Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be
operated simultaneously without reassess ment permissive change.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement en
association avec une autre antenne ou transmetteur. This module isintended for OEM
integrator.
The OEM integratorisstillresponsible for the IC compliance requirement of the end
product, whichintegratesthis module.
In the usersmanual of the end product, the end user has to beinformed to keep at least
20cm separation with the antenna while this end product is installed and operated. The
end user has to beinformed that the IC radio-frequencyexposure guidelines for an
uncontrol led environment can be satisfied. The end user has to also be informed that
any changes or modifications not expressly approved by the manufacturer could void
the user's authority to operate this equipment. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
The final end product must belabeled in a visible area with the following " Contains TX
IC : 12425A-F23BUUM13W2".
EU Regulatory Conformance
Hereby, we (FN-Link Technology Limited) declared that this device is in compliance with
the essential requirements and other relevant provisions of Directive 1999/5/EC.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : Administrator
Title                           : Microsoft Word - Fender FMA WIFI-USB-FTSW Manual Rev1.docx
Create Date                     : 2016:11:02 11:20:41+08:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2017:03:06 10:51:39+08:00
Metadata Date                   : 2017:03:06 10:51:39+08:00
Producer                        : Acrobat Distiller 9.3.3 (Windows)
Document ID                     : uuid:f9ff4035-0c5b-4c50-b9de-4b584cc3a446
Instance ID                     : uuid:7d7fbfe4-3c2d-428f-845b-8a226b920f5e
Page Count                      : 8
Author                          : Administrator

EXIF Metadata provided by EXIF.tools