Fender Musical Instruments FMAPR5133 WIFI+BT Module User Manual C Users Sance wang Desktop

Download:
Mirror Download [FCC.gov]
Document ID	3588805
Application ID	mWjP2FMoCE/xQYtZzE54wg==
Document Description	15_7712066000 UserMan r2
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	79.5kB (993734 bits)
Date Submitted	2017-09-30 00:00:00
Date Available	2017-09-30 00:00:00
Creation Date	2017-09-23 15:40:08
Producing Software	Microsoft: Print To PDF
Document Lastmod	2017-09-23 15:40:08
Document Title	C:\Users\Sance.wang\Desktop\~$user manual.pdf
Document Author:	Sance.wang

FMA Integrated WiFl Moduie P/N 7712066000
Manual and Spec
Reference Documents
- FN-LINK F238UUM13-W2 moduie product specification
0 Fender FMA WirFi schematic
Description
The Fender FMA Wi-Fi board is used to provide wireless connectivity, Wi-Fi and Biuetooth, forthe famiiy
of Fender Modular Architecture (FMA) products.
Circuit Description
Referring to the block diagram, there are three main sections of the circuit:
a FNiLink FZSBUUMISVWZ module
0 USB port
I PCB ”F” Antenna
Communication with the FNrLink module is accumpiished through a USE 2.0 port connected through a
signai path that uitimately goes to the system host processor. The WirFi and Bluetooth radio circuitry is
contained on the FNrLink module. There is no antenna on the module so the radio output from the
module connects to an FrTvpe PCB antenna on the PCBA. The FNrLink moduie operates from a 3.3V
suppiy sourced through the USB cable. The VBUS conductor on the USB cable supplies the 3.3V instead
ofthe typical 5V VBUS. Damage to the FN-Link module will occur ifthe moduie is connected to 3 5V USB
VBUS supply.
FN-Link Module installation and Use
The FN-Link moduie is soldered to the PCBA. Pads on the PCBA make contact to the 3.3V supply, USB
port and antenna. Ali communication between the host processor and the module is accomplished
through the modules USB port. A description ofspecific commands for Bluetooth and WirFi driver
development is beyond the scope of this document and can be found in documentation from Reaitek for
the RTL87Z3BU Wi-Fi+BT chip or elsewhere.
Block Diagram
VNNZLNV EDd
Fender FMA WIFI Block Diagram
110d asn
USB Connector
The pinout forthe USB connector follows the standard for microiB USB except the VBUS power is
reduced to 3.3V. The connector pinout is below:
Pin Signal Description
1 +3.3V Power
2 USBiDN USB data signal
3 USB_DP USB data signal
4 , No connection
5 6 ND G N D
FN-Link Module
The FN-LINK F233UUM13-WZ module takes care of all wireless communication. The host processor
communicates to the module through a USB port. The wireless module is supports a number of IEEE
standards including IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.1111, lEEE 802.11e, IEEE 802.11h
and IEEE 802.11i. The module also supports Bluetooth specs including Bluetooth 3.0 and Bluetooth 4.0
Dual mode. For a complete list of supported wireless standards please refer to the product specification
for the FN-Link FZSBUUMIS-WZ module.
Antenna
An Frtype PCB antenna is located on the PCB to support the 2.4GHz signal from the FNrLink module,
Power Consumption
Operating Voltage 3,3VDC +/, 9%
WiFi mode current ZOOmA (TX/RX continuous mode)
2.1 mA (idle power saving)
0,1mA (Idle or RF disable mode)
BT 15mA (sco HV3)
0.9mA (Inquiry and Page Scan)
7.5mA (ACL no traffic)
Board Dimensions
58.0mm
11.0mm
><><><>OO<>3000009000<
X X
X X 5.45mm +/-0.05mm
X X X X X XX 2 X
393mm ® XX X X X X
X X X
J. 1. X 32
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference. (2) This
device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
---Reorient or relocate the receiving antenna.
---|ncrease the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
LABEL OF THE END PRODUCT:
The final end product must be labelled in a visible area with the following "Contains TX
FCC ID: XQW-FMAF'R5133”. If the size of the end product is smaller than 8x10cm, then
additional FCC part 15.19 statement is required to be available in the users’ manual:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
RF Exposure
This device has been evaluated and shown compliant with the FCC RF Exposure limits
under fixed exposure conditions (antennas are greaterthan 20cm from a person's body)
when installed in certain specific OEM configurations.
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co—located or operating in
conjunction with any other antenna or transmitter. Due to missing shielding the module
is strictly limited to integration by the Grantee himself or his dedicated OEM integrator
under control of the Grantee. However, the OEM integrator is still responsible for testing
their end-product for any additional compliance requirements required with this module
installed.
IMPORTANT NOTE:
This device is intended only for OEM integrators under the following conditions:
(1) According to FCC Part 15 Subpart C Section 15.212, the radio elements of the
modular transmitter must have their own shielding. However, due to there is no
shielding for this WIFI/BT module, this module is granted as a Limited Modular
Approval.
(2) This module has been designed to operate with PCBA antenna having a maximum
gain of 1.0 dBi.
(3) Integration is typically strictly restricted to Grantee himself or dedicated OEM
integrators under control of the Grantee.
The module will be responsible to satisfy SAR/RF Exposure requirements, when the
module integrated into any (portable, mobile, fixed) host device.
This module is intended for OEM integrator only and the OEM integrators and instructed
to ensure that the end user has no manual instructions to remove or install the device.
The OEM integrator is still responsible for the FCC compliance requirement of the end
product, which integrates this module.
The module has no shielding and tested stand alone. This module is tested and
approved as Limited modular approval with stand alone configuration, any OEM
incorporated this radio module into any system are require additional testing and
evaluation.
The module is only certified with the installed antenna. Any change of the antenna will
void the certification.
IC Notice:
This device complies with Canada Industry licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1)this device may not cause interference; and
(2) this device must accept any interference. Including interference that may cause
undesired operation of the device.
Avis d’lndustrie Canada
Le present appareil est conforme aux CNR d'industrie Canada applicables aux
appareils radio exem pts de licence L'exploitation est autorisée aux deux conditions
suivantes:
1) I'appareil ne doit pas produire de brouillage; et
2) l'utillsateur de l'appareil doit accepterbrouillage radioélectrique subi meme si le
brouillage est susceptible d'encompromettre le fonctionnement. mauvais
fonctionnement de l'appareil.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrélé. Cet équipement doit étre installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This device and its antenna(s) must not be co-located with any other transmitters except
in accordance with IC multi-transmitter product procedures.
Refering to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be
operated simultaneously without reassessment permissive change.
Cet appareil et son antenne (s) ne doit pas étre co-localisés ou fonctionnement en
association avec une autre antenne ou transmetteur. This module is intended for OEM
integrator.
The OEM integrator is still responsible for the IC compliance requirement of the end
product, which integrates this module.
In the users manual of the end product, the end user has to be informed to keep at least
20cm separation with the antenna while this end product is installed and operated. The
end user has to be informed that the IC radio-frequency exposure guidelines for an
uncontrolled environment can be satisfied. The end user has to also be informed that
any changes or modifications not expressly approved by the manufacturer could void
the user's authority to operate this equipment. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
The final end product must be labeled in a visible area with the following “ Contains TX
IC : 8690A—FMAPR5133 ".
This radio transmitter (identify the device by certification number, or model number if
Category II) has been approved by Industry Canada to operate with the antenna types
listed below with the maximum permissible gain and required antenna impedance for
each antenna type indicated.
Le present émetteur radio (identifier le dispositif par son numéro de certification ou son
numéro de modele 3'“ fall partie du materiel de categorie I) a ete approuvé par Industrie
Canada pour fonctionner avec les types d'antenne enuméres ci-dessous et ayant un
gain admissible maximal at l‘impe'dance requise pour chaque type d'antenne.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : Sance.wang
Create Date                     : 2017:09:23 15:40:08+08:00
Modify Date                     : 2017:09:23 15:40:08+08:00
Producer                        : Microsoft: Print To PDF
Title                           : C:\Users\Sance.wang\Desktop\~$user manual.pdf
Page Count                      : 9

EXIF Metadata provided by EXIF.tools