Fender Mustang_Mini_advanced_manual_rev B_English Mustang Mini Advanced Manual Rev B English

User Manual: Fender Mustang_Mini_advanced_manual_rev-B_English Fender® Guitar Amplifier Owner's Manuals (Current) – Fender

Open the PDF directly: View PDF .
Page Count: 6

GUITAR AMPLIFIER

MUSTANG MINI BY FENDER ®

™

ADVANCED OWNER'S MANUAL

MUSTANG™ MINI

Advanced Manual

Introduction

This manual is your step-by-step guide to all the advanced

features found on your Mustang™ Mini amplifier. For free

downloads and information on using Fender® FUSE™ software,

please visit fuse.fender.com.

Using Presets

Turn the PRESET knob to select one of 24 presets. Presets are

stored in three banks, colored AMBER, GREEN and RED, in the fol-

lowing order:

Each preset is based on one of the eight amplifier types labeled

next to each of the preset LEDs. Each preset stores the settings

for every parameter on the amplifier (volume, tone, effects, etc.)

except for the master volume level which can only be adjusted by

turning the MASTER knob manually.

♫ The RED and GREEN banks are for storing your own

custom presets. The AMBER bank of presets can only be

modified using Fender® FUSE™ software, available free of

charge at

fuse.fender.com

.

Programmable Knobs

The four programmable knobs (GAIN, VOLUME, TREBLE, EFFECTS)

will NOT show their true settings when you first select a new preset.

This is because the stored preset setting for each knob can be dif-

ferent from the position that the knob is currently pointing to.

123

Simply turn a knob to activate it and adjust its current setting. The

knob will remain active until you select a different preset, at which

time the programmable knobs all become inactive again.

123

♫ You may hear a significant change in volume or tone when

you first turn a programmable knob as the preset setting for

the knob instantly shifts to the activated knob position.

♫ The only way to see what the level of a programmable knob

is BEFORE you turn it is by using Fender FUSE software.

Tone Adjustments (Treble and Bass)

Turn the TREBLE knob to adjust the high-frequency tone of the

Mustang Mini amplifier. To adjust the low-frequency BASS tone,

press and hold the EXIT button while turning the TREBLE knob:

123

Effects

Effect Selections

Turn the EFFECTS knob to select one of 12 effects. Select "OFF" for

no effects.

A1:

Chorus

A2:

Flanger

A3:

Phaser

B1:

Vibratone

B2:

Vintage Tremolo

B3:

Octave Down

C1:

Small Room Reverb

C2:

Fender ’65 Spring Reverb

C3:

Stereo Tape Delay

D1:

Tape Delay + Room Reverb

D2:

Chorus + Hall Reverb

D3:

Vibratone + Room Reverb

Programmable knobs are inactive until turned

Rotate programmable knobs to activate

AMBER 4 GREEN 4 RED

Adjusting the BASS level

2fender.com

MUSTANG™ MINI

♫ You can completely change the list of effects available on

your Mustang Mini amplifier as well as access bonus effect

parameters using Fender FUSE software!

The three LEDs next to the EXIT button are numbered to indicate

which effect position (1, 2 or 3) is being selected within each of the

four selection ranges (A, B, C and D). For example, effect selection

"A1" is shown below:

Effects Level

To adjust the level of effects for the current preset, press and hold

the EXIT button while turning the EFFECTS knob:

123

Tap Button

The TAP button can be used to tap in delay time and modulation

rate settings for the current effect:

• Delay time — TAP button blinks green:

• Modulation rate — TAP button blinks red:

When you select a delay type effect, the TAP button will blink

green in sync with the delay time setting. When you select a

modulation type effect, the TAP button will blink red in sync with

the modulation rate setting.

To set the TAP interval of effects:

1. Select an effect that causes the TAP button to blink, using the

EFFECTS knob.

2. Press the TAP button twice rhythmically in time with the

desired interval.

♫ Press the TAP button just one time to set the delay or

modulation interval to its maximum value.

Guitar Tuner

Your Mustang™ Mini amplifier has a built-in Tuner mode that uses

the control panel LEDs as a chromatic guitar tuner.

To use the tuner:

1. Press and hold the TAP button for 2 seconds. The TAP and EXIT

buttons will illuminate.

2. Strike any single string on your guitar and watch the panel

LEDs. The Preset LEDs are used to indicate the note of the

string being tuned (the top LED "#" also lights up to indicate if

the note is sharp).

123

3. Turn the tuning peg on your guitar until the fine tuning LEDs

next to the EXIT button indicate that the string is in tune, as

shown above.

4. Standard guitar tuning is as follows:

5. Press EXIT or TAP to exit from the Tuner.

Letters next to LEDs indicate the note being tuned

3 LEDs indicate fine tuning. GREEN means "in tune"

Adjusting the EFFECTS level

3

fender.com

MUSTANG™ MINI

Save Button

Your Mustang Mini amplifier gives you the powerful

ability to save every setting on the amplifier as part

of a preset. The SAVE button will light up red when you turn any

programmable knob on the amplifier. This indicates that you

have temporarily modified the current preset. You can undo your

modifications simply by selecting a different preset using the

PRESET knob, then turning back to the original preset.

♫ The EXIT button will not cancel changes to the current

preset. Only by selecting a different preset using the PRESET

knob, the footswitch or Fender FUSE, will your temporary

changes be erased.

To save your own custom preset:

1. To save a preset you must first modify an existing preset by

turning any of the programmable knobs, such as GAIN (once

the SAVE button is illuminated, you can proceed to step 2).

2. Press the SAVE button. The SAVE and EXIT buttons should be

flashing rapidly. You can press EXIT at this point to cancel the

save process.

3. Turn the PRESET knob to select a preset to overwrite. You

can only overwrite the red and green banks of the amplifier

type that you started from (if you started by modifying the

amber bank, you must select either the red or green bank to

overwrite).

♫ You can save over the AMBER bank of presets only by using

Fender® FUSE™ software.

4. Press the SAVE button again to confirm the save. Your new

preset has been created!

Aux / Phones Jacks

Auxiliary Input

You can use the Auxiliary jack to input audio into your

Mustang Mini amplifier for accompaniment. Connect the

headphone output on your CD player or MP3 player to

the AUX jack using a mini-stereo cable. Use the volume control

on your player, together with the MASTER volume knob on the

Mustang Mini, to adjust the auxiliary volume level.

Phones Jack

Plug in your headphones, ear buds, or powered speakers

to enjoy the Mustang Mini's stereo features. This jack

may also be used as a stereo recording output. The

amp's internal speaker is muted when the PHONES jack is used.

Footswitch

Connect a (optional) 1-button footswitch (P/N

0994049000) into the FTSW jack to enable remote

selection of your two favorite presets. The LED above

the FTSW jack will turn red or green to indicate which

footswitch preset is active.

To program the footswitch:

1. Select a preset that you want to assign to the footswitch. The

preset must not be modified (the SAVE button must NOT be

illuminated to proceed to step 2).

2. Press the SAVE button. The SAVE and EXIT buttons should be

flashing rapidly. You can press EXIT at this point to cancel the

footswitch assignment process.

3. Press the footswitch button to select either the red or green

LED above the FTSW jack that you wish to associate with the

current preset.

4. Press the SAVE button to confirm the footswitch assignment.

Now, when you press the footswitch, the chosen preset will be

activated with the assigned red or green footswitch indicator.

USB Port

Use the USB port to connect the Mustang™ Mini amplifier

to your computer and take your music to the next level:

• Use Fender® FUSE™ software to control the Mustang Mini

from your computer and access bonus amp features not

available from the amplifier alone.

• Record and edit Mustang Mini audio using your favorite

recording software.

♫ You can adjust the USB recording volume level by pressing

and holding the EXIT button while you turn the VOLUME

knob.

4fender.com

MUSTANG™ MINI

Factory Restore &

Firmware Updates

Factory Restore

You can restore your Mustang Mini amplifier to the original factory

settings if desired. All user presets will be erased!

To restore the Mustang Mini amplifier to factory settings:

1. Turn the amplifier OFF.

2. Press and hold the EXIT button while turning the amplifier

ON. Continue holding the EXIT button until it is no longer

illuminated.

! The FACTORY RESTORE function will erase all user modified

presets. It will also restore the AMBER bank of presets and

any effect selections that have been modified using Fender

FUSE software.

Firmware Update

From time to time, Fender may make available firmware updates

for your Mustang Mini amplifier to improve operation or to add

new features. To update the firmware on your amplifier you will

need to connect it through the USB port to a computer with an

internet connection and running Fender FUSE software.

♫ Please download the latest version of the Fender FUSE

manual from fuse.fender.com.

Notes & Tips

♫ LOW BATTERY: When running the Mustang Mini on

batteries, the amp will start to distort at lower volumes

as the batteries get low. At critically low battery levels the

speakers will cut out intermittently. Change the batteries if

either of these conditions occur.

♫ You can use the handle on your Mustang Mini amplifier

as a tilt-back leg to support the amplifier at an angle for

improved sound projection.

♫ You can loop the power adapter cable around the clip on

the back panel of your Mustang Mini amplifier to prevent it

from disconnecting.

There are several great places you can go to learn more about your

Mustang Mini amplifier and music in general:

• www.fender.com/support

• Join a Fender Community forum where you can ask questions

and read threads. There's even a forum just for the Mustang:

www.fender.com/community/forums

• Find music theory learning materials and sheet music at Hal

Leonard Publications: www.halleonard.com

Battery compartment

Tilt-back position

Power cord clip

5

fender.com

This product is covered by one or more of the following patents:

US Pat. 6,222,110

AMPLIFICADOR DE AUDIO

IMPORTADO POR: Instrumentos Musicales Fender S.A. de C.V., Calle Huerta # 132, Col. Carlos Pacheco, C.P. 228890, Ensenada, Baja California, Mexico.

RFC: IMF870506R5A Hecho en China. Servicio de Cliente: 001-8665045875

A PRODUCT OF:

FENDER MUSICAL INSTRUMENTS CORPORATION

CORONA, CALIFORNIA, USA

Fender®, Mustang™ and Fender® FUSE™ are trademarks of FMIC.

Other trademarks are property of their respective owners.

Copyright © 2011 FMIC. All rights reserved. P/N 1198CMU016 (ENGLISH) rev b

有毒有害物质或元素

(Hazardous Substances’ Name)

部件部件名称

(Part Name) 铅

(PB)

汞

(Hg)

镉

(Cd)

六价铬

(Cr6+)

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

部分电子元件 x o o o o o

部分机器加工金属部件 x o o o o o

部分其他附属部件 x o o o o o

O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 规定的现量要求以下

X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T 11363-2006 规定的现量要求