FengShun Peiying Electro Acoustic XDMA760BT AM/FM/CD/MP3 Receiver User Manual

FengShun Peiying Electro-Acoustic Co., Ltd AM/FM/CD/MP3 Receiver

User manual

Front and Rear InputsINSTALLATION/OWNER'S MANUALCD ReceiverXDMA760BT
2XDMA760BTREMOVALKEYSHEAD UNITMOUNTING SLEEVEOPTIONAL REARMOUNTING SUPPORTBLUEBLACKREDYELLOWRemoteTurn-OnConn ect to amplifier or powerantenna. Insulate wire if not used.GroundConn ect to the vehiclechassis ground.AccessoryConn ect to an existing ignitioncircuit or switched 12 volt source.MemoryConn ect to the batterycircuit or constant 12 volt source.Right FrontGray/Black (-)Gray (+)Left FrontWhite/Black (-)White (+)Left RearGreen/Black (-)Green (+)Right RearViolet/Black (-)Violet (+) SUBREARFRONTL-CHR-CHAntennaConnectorRear OutputFront OutputSubwoofer OutputSteering WheelPlease read entire manual before installation.Before You Start• Disconnect negative battery terminal. Consult a qualified technician for instructions.• Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started• Remove trim ring from unit.• Remove 2 transit screws located on top of the unit. • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • Install mounting sleeve into opening, bending tabs to secure. • Connect wiring harness and antenna. Consult a qualified technician if you are unsure. • Certain vehicles may require an installation kit and/or wiring harness adapter (sold separately). • Test for correct operation and slide into mounting sleeve to secure. • Snap trim ring into place.PreparationTYPICAL DIN FRONT-LOAD MOUNTING METHOD
3XDMA760BTBLUEBLACKREDYELLOWRemoteTurn-OnConn ect to amplifier or powerantenna. Insulate wire if not used.GroundConn ect to the vehiclechassis ground.AccessoryConn ect to an existing ignitioncircuit or switched 12 volt source.MemoryConn ect to the batterycircuit or constant 12 volt source.Right FrontGray/Black (-)Gray (+)Left FrontWhite/Black (-)White (+)Left RearGreen/Black (-)Green (+)Right RearViolet/Black (-)Violet (+) SUBREARFRONTL-CHR-CHAntennaConnectorRear OutputFront OutputSubwoofer OutputSteering WheelFUSEWhen replacing the fuse, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the radio. The XDMA760BT uses one10 amp ATM fuse located in-line.Wiring Diagram
4XDMA760BTAuxiliary InputTune / Track DownPreset Down / Thumbs DownDisplayMuteBand / Go BackPowerMenuOpenSourceBluetooth TalkPlay / PauseVolume Knob/ Select (push)Preset Up / Thumbs UpTune / Track UpFunctionUSB Port1 2 3 4 91 102 113 124 135 146 157 168914101165121317 1516Control Locations - Receiver177 8
5XDMA760BTPreset Up / Thumbs Up Key 0 / Key +Preset Down / Thumbs DownKey 7 / Key *Key 5 / Folder DownKey 4 / Play / PauseKey 1 / RepeatKey 2 / RandomTalkTune / Track DownSourceVolume UpPowerSelectTune / Track UpVolume DownBand / Go BackKey 3 / IntroKey 6 / Folder UpKey 9 / Key #Key 8 / Mute110211312413514615716817918Control Locations - Remote1235689104151617181911192072115141213192021
6XDMA760BTPress OPEN to open the face plate, then pull away from the right side to remove. To re-install, insert right side of faceplate first then push left side to secure.Press or any other button to turn the unit on. Press to turn the unit off.Press SOURCE to enter the Source Menu, then press SOURCE or rotate the volume knob to select between Tuner, Disc, Auxiliary Input, USB, iPod, Bluetooth and Pandora modes. Modes of operation are shown in the display. The XDMA760BT offers an auxiliary input ports for connecting an audio device, MP3 player, etc. Press SOURCE to select auxiliary input mode. Adjust volume using volume knob (00-46).Press DISP to toggle between ID3 tag and file/folder name for MP3/WMA files being played from CDs or USB devices.Press RESET upon initial installation or if abnormal operation occurs. Reset button is located behind the front panel. The unit will display the time on the LCD display. Clock settings are adjusted in the General setup menu.The clock will display 12-hour AM/PM time or 24-hour time (22:00). Frequency spacing is adjusted in the General setup menu (refer to page 8).Faceplate RemovalPower On/OffSourceAuxiliary InputVolumeDisplayResetSet the Clock12/24-hour Clock General Operation
7XDMA760BTGeneral OperationAudio Setup MenuMenu Function OptionsEqualization CurvesRotate the volume knob to cycle through the following equalization curves: Flat, Pop, Jazz, Classic, Beat, Rock and User. Any manual adjustment to the Bass or Treble settings are automatically saved as User.Bass Level Rotate the volume knob to adjust the bass level setting (-6 minimum / +6 maximum).Bass Frequency Rotate the volume knob to select one of the following bass frequency settings: 60 Hz, 80 Hz, 100 Hz or 200 Hz.Middle Level Rotate the volume knob to adjust the middle level setting (-6 minimum / +6 maximum).Middle Frequency Rotate the volume knob to select one of the following middle frequency settings: 500 Hz, 1 kHz, 1.5 kHz or 2.5 kHz.Treble Level Rotate the volume knob to adjust the treble level setting (-6 minimum / +6 maximum).Treble Frequency Rotate the volume knob to select one of the following treble frequency settings: 10 KHz, 12.5 KHz, 15 KHz or 17.5 KHz.Balance Rotate the volume knob to adjust the balance setting.(12-L to 12-R; 0 represents equal balance).Fader Rotate the volume knob to adjust the fader setting.(12-F to 12-R; 0 represents equal balance)Subwoofer Rotate the volume knob to turn subwoofer output ON or OFF.Subwoofer Level Rotate the volume knob to adjust subwoofer level between 0 and 12.Subwoofer FrequencyRotate the volume knob to select one of the following subwoofer center frequency settings: Off, 80 Hz, 120 Hz and 160 Hz. "Off" represents a full range subwoofer output.Press MENU to toggle through and select one of the following setup menus: Audio, General, Gain and Screen. 1. Once the desired menu is displayed, rotate the volume    knob to scroll through the list of menu features. 2. Press SELECT to select a specific feature to adjust, then rotate the volume knob left/right to adjust or activate the desired feature. 3. Press SELECT to confirm and save the changes.Setup Menu
8XDMA760BTGeneral OperationMenu Function Options ActionTunerFrequencySpacingUSA Programs the unit to USA tuner spacing.(200kHz for FM and 10kHz for AM). S-America Programs the unit to South American tuner spacing.(100kHz for FM and 10kHz for AM).Europe Programs the unit to European tuner spacing.(50kHz for FM and 9kHz for AM).Auto Station Store AUTO STORE Press SELECT to seek and save 6 strong stations in the current band. Local/Distance TuningOff Activates distance tuning.On Activates local tuning for strong station reception only.Set the Clock ClockRotate the volume knob to adjust the hours, then press SELECT to confirm. Repeat to adjust the minutes, and repeat again to adjust AM/PM setting. Clock Mode 12 Hour Programs the unit to display 12-hour AM/PM time (example: 10:00 PM)24 Hour Programs the unit to display 24-hour time (example: 22:00)Scrolling OptionOff Programs the unit to not scroll any information on the display.Once Programs the unit to only scroll information once.15Sec Programs unit to scroll information once every 15 seconds (default).On Programs unit to scroll information continuously.iPod ControlFull Programs the head unit to advanced control of the iPod/iPhone device. ManualPrograms the head unit to manual control of the iPod/iPhone device and allows music to be controlled from the iPod/iPhone device. Beep ConfirmationOff Disables the confirmation beep.On Enables the confirmation beep.Programmable Turn On VolumeVariableValuePrograms unit to always turn on at a specific volume(default is Off). A volume level of 1-30 can be selected.General Setup Menu
9XDMA760BTGeneral OperationGain Setup MenuMenu Function OptionsTuner Gain Rotate the volume knob to adjust the tuner gain. (-6 minimum / +6 maximum)Disc Gain Rotate the volume knob to adjust the gain for disc playback. (-6 minimum / +6 maximum)Aux Gain Rotate the volume knob to adjust the gain for the front auxiliary input. (-6 minimum / +6 maximum)Bluetooth Rotate the volume knob to adjust the gain for the rear auxiliary input. (-6 minimum / +6 maximum)USB Gain Rotate the volume knob to adjust the gain for USB playback. (-6 minimum / +6 maximum)iPod Gain Rotate the volume knob to adjust the gain for iPod playback. (-6 minimum / +6 maximum)Pandora Gain Rotate the volume knob to adjust the gain for Pandora playback. (-6 minimum / +6 maximum)Screen Setup MenuMenu Function OptionsDemo Rotate the volume knob to to enable (ON) or disable (OFF) the demonstration mode.Backlight Rotate the volume knob to adjust the brightness settings of the display screenfrom 1 to 7.
10XDMA760BTManual TuningSeek TuningBand Storing Station PresetsRecalling Station PresetsPress TUNE nn or TUNE ll momentarily to change radio frequency up or down one step at a time. Press and hold to advance quickly. Press TUNE nn or TUNE ll for more than two seconds (then release) to automatically seek and tune to the next strong station.Press BAND to select between FM1, FM2, FM3, AM1 and AM2 bands.Select the desired band and station. Press the (F)unction button, turn the volume knob until the desired preset number is highlighted, then press SELECT to store the preset.Press the P+ or P- buttons to cycle through the 1-6 presets in the current band.AM/FM Tuner Operation
11XDMA760BTInsert CDEject CDTrack SelectFast Forward/ReversePauseRepeatRandomIntroCD-R/CD-RW CompatibilityPress OPEN to fold down the front panel and expose the CD slot. With the label facing up, insert a standard size CD into the CD slot. The CD will automatically begin playback. With the front panel open, press EJECT to eject the CD. The unit will change to previous mode of operation. If the disc is not removed within 10 seconds, the unit will reload the disc. The unit does not have to be turned on to eject CD.Press TRACK ll to skip to the beginning of the next track. Press TRACK nn to return to the beginning of the current track. Pressing TRACK nn again skips to the beginning of the previous track.Press and hold TRACK ll or TRACK nn on the remote control to fast forward or reverse a track. Press l/ II to temporarily stop CD playback.Press l/ II again to resume playback.Press (F)unction and choose Repeat to continuously repeat the selected track.Press (F)unction and choose Random to play all the tracks in random order.Press (F)unction and choose Intro to play the first 10 sec-onds of each track. Some CD-Rs and CD-RWs may be incompatible with this unit, depending on media type and recording method. In addition, the following CDs may be incompatible with this unit:CDs exposed to extreme temperatures or direct sunlight for extended periods of time, CDs recorded in which a recording session failed or a re-recording was attempted and, or encrypted or copy-protected CDs which do not conform to the audio CD-DA red book recording standard.CD Operation
12XDMA760BTPlaying MP3/WMA FilesDisplaying InformationRepeatRandomIntroTo play MP3/WMA files, insert a data CD or USB device containing MP3/WMA files. “Loading" will flash in the display. Depending on the number of files and folders, this may take several seconds. Press DISP to cycle between track information and file/folder information.*Song title, artist name and album name will only be displayed if included with the MP3/WMA file. When referring to MP3/WMA playback, the following terms are synonymous:• File name and track name• Folder name and directory namePress (F)unction to enter the Function Menu, then rotate the volume knob until Repeat is highlighted. Press SELECT, then rotate the volume knob to select one of the following repeat options. • All - Plays all songs on disc or device. • Track - Continuously repeats selected song. • Folder - Continuously repeats all songs in selected folder. Press (F)unction to enter the Function Menu, then rotate the volume knob until Random is highlighted. Press SELECT, then rotate the volume knob to select one of the following options for random playback. • Off - Cancels the Random function. • All - Plays all songs in random order. • Folder - Plays all songs in folder in random order. Press (F)unction to enter the Function Menu, then rotate the volume knob until Intro is highlighted. Press SELECT, then rotate the volume knob to select one of the following options for intro playback. • Off - Cancels the Intro function. • All - Plays first 10 seconds of each song. • Folder - Plays first 10 seconds of each song in folder. Note: Folder repeat, random and intro options only function on MP3/WMA discs or devices recorded with more than one folder.MP3/WMA Operation
13XDMA760BTMP3/WMA OperationFile/Folder SearchPressSELECTPressBACKSELECTTurn the volume knobFolder 1 Folder 2 Folder 3 Folder 4 Folder 5 Folder 6 Folder 7FilesFiles Files Files FilesFilesFilesPress SELECTto beginPress SELECT to enter the file/folder search mode. A list of all the folders from the disc or device will be displayed. Note: Any files located in the root directory will be located in the folder named "ROOT". Turn the volume knob to cycle through all the folders on the disc or device, and press SELECT to choose the desired folder. The list of files in the selected folder will be displayed. Turn the volume knob to cycle through the list of files.Pressing GO BACK when viewing the contents of a folder will return to the list of folders on the disc or device. Press GO BACK again to exit the search menu.Once the desired song is displayed, press SELECT to begin Begin SearchingChoose a SongMenu NavigationPlaying a Song
14XDMA760BTMP3/WMA OperationType SpecificationCompatible File Types• CD-ROM (ISO), CD-R, CD-RW• CD-DA (digital audio)• MP3 data (.mp3)• WMA data (.wma)Incompatible File Types• DRM protected files• WMA lossless• Apple lossless• WMA Pro• MP3 Pro • MP3 playlists• WAV lossless• M4A/AAC dataRecording Format Compatibility• ISO9660 level 1 & level 2• Yellow book MODE 1 & MODE 2 FORM 1• Multi sessionSampling Frequency Rate Compatibility• MP3: 8kHz - 48kHz• WMA: 32kHz - 48kHzTransfer Bit Rate Compatibility• MP3: 32kbps - 320kbps• WMA: 32kbps - 192kbpsCharacter Support• Song Title: 32 characters• Artist Name: 32 characters• Album Name: 32 characters• File Name: 32 characters• Folder Name: 32 charactersID3 Tag Support • MP3 Tags: Version 1.0 - 2.4• WMA TagsFile/Folder Limit• Maximum files: 999• Maximum folders: 500• Maximum folder levels: 8File/Folder Compatibility and Support - CD
15XDMA760BTMP3/WMA OperationType SpecificationCompatible File Types • MP3 data (.mp3)• WMA data (.wma)Incompatible File Types• DRM protected files• WMA lossless• Apple lossless• WMA Pro• MP3 Pro • MP3 playlists• M4A/AAC data• WAV losslessSampling Frequency Rate Compatibility• MP3: 8kHz - 48kHz• WMA: 32kHz - 48kHzTransfer Bit Rate Compatibility• MP3: 32kbps - 320kbps• WMA: 32kbps - 192kbpsCharacter Support• Song Title: 32 characters• Artist Name: 32 characters• Album Name: 32 characters• File Name: 32 characters• Folder Name: 32 charactersID3 Tag Support • MP3 Tags: Version 1.0 - 2.4• WMA TagsFile/Folder Limit• Maximum number of files: 999• Maximum number of folders: 500 (plus the root folder)• Maximum number of files in each folder: 999Note: For devices with more than the maximum number of files/folders, some files will be ingnored and may not function properly. USB/SD File System • FAT/FAT32 file system supported.• HFS/NTFS/EXT2/EXT3 not supported.File/Folder Compatibility and Support - USB
16XDMA760BTiPod OperationThe XDMA760BT features a direct USB control system for iPod. To play music from an iPod device, connect the USB cable (included with your iPod device) to the USB port on the front panel. Once connected, "Loading" will flash in the display, then playback will begin automatically. If a song is playing on the iPod device before it is connected, it will continue to play.Connect an iPod Device(Not Included)Search Item Menu NavigationPlaylist Menu Playlists SongsSongs Menu Songs Artists Menu Artists Albums Songs Albums Menu Albums SongsPodcase Menu PodcastsSee the below table for a list of the search menu navigation options.Search Menu Functions(step 1)(step 2)(step 3)Press SELECT once to enter the search mode. Rotate the volume knob to choose between playlist, songs, artists, albums and podcasts. Press SELECT to select the desired search type. Navigate to the desired song and press SELECT to begin playback of that song. Use the table below for reference when navigating through the menu options.Note: Press GO BACK to access the previous level (up one level). Pressing GO BACK from the search main menu will exit the search.Search ModeFull/Manual ControlThe XDMA760BT features both full and manual control modes for iPod/iPhone devices. See page 8 for details to toggle the control between full and manual modes.Important: To support manual control for iPod/iPhone, the iPod device must be updated to the newest firmware. Note: Not all iPod/iPhone devices are compatible with manual control mode.
17XDMA760BTiPod OperationPress ll to skip to the beginning of next song. Press nn to return to the beginning of current song. Pressing nn again skips to the beginning of previous song.Press and hold ll or nn to fast forward or reverse a song. Press l/ II to temporarily stop playback.Press l/ II again to resume playback.Press (F)unction to enter the Repeat menu, then turn the volume knob to select one of the following options:• Off - Repeats all tracks.• Current Song - Repeats selected track. Press (F)unction to enter the Random menu, then turn the volume knob to select one of the following options:• Off - Cancels the RDM function.• All Songs - Plays all tracks in random order. • Current Album - Plays all tracks in the selected album in random order. Press (F)unction to enter the Intro menu, then turn the vol-ume knob to select one of the following options:• Off - Cancels the INT function.• On - Plays first 10 seconds of each track. Only alphanumeric characters can be displayed (ASCII type). "NO SUPPORT" will be displayed if the file contains characters that can not be displayed. "NO FILE" will be displayed if there are no songs in the selected playlist.Maximum character display information• *Song title – 32 character maximum• *Artist name – 32 character maximum• *Album name – 32 character maximum*Song Title, Artist Name and Album name will only be displayed if included with the file.               Song Select  Fast Forward and Reverse  PauseRepeatRandomIntroCharacter Support
18XDMA760BTBluetooth  OperationBefore you can use a Bluetooth device, it must be paired andconnected. Make sure that Bluetooth is activated on yourdevice before you begin the pairing process.The XDMA760BT broadcasts the pairing signal constantlywhen no devices are currently connected. Complete thepairing sequence from your Bluetooth device. Refer to theowner's manual for your device for more details.The device name is "Dual BT"The Bluetooth passcode "1234"Note: The XDMA760BT can be in any mode of operationwhen pairing is performed.If a device is currently connected, press and hold todisconnect the current device before a new device canbe paired. Then begin the pairing sequence from the newBluetooth device.PreparationPairing a New DevicePairing AdditionalDevicesMost Bluetooth devices support the auto-connect feature, and will connect automaticallyif the device is in range when the XDMA760BT is powered-on. If your device was previouslypaired but does not connect, use these instructions below.• If your most recently connected Bluetooth device becomes disconnected or does not reconnect, press from Bluetooth mode to reconnect your mobile device.• To connect a previously paired device that was not recently connected:1) If applicable, press and hold to disconnect any connected mobile devices.2) From Bluetooth mode, press SELECT. "Paired Devices" will appear on the LCD.3) Turn the volume knob to cycle through the list of devices.4) Press SELECT or to connect to the desired device. It must be in range to connect.Note: If the Auto Connect setup menu setting is set to OFF, you must press toconnect you device after pairing, and each time the XDMA760BT is powered-on.Connecting a Paired DeviceDisconnecting a DevicePress and hold for 3 seconds to disconnect a connected device. The device will remainpaired and appear in the PAIRED DEVICES menu but will not be connected. Pairing a Device
19XDMA760BTPress and hold for 3 seconds to disconnect a connected device. The device will remain paired and appear in the SEARCH menu, but not be connected. Press once. “Enter Phone Number” appear on the display. Using the remote control, enter the phone number using the 0-9 buttons. Press or SELECT on the remote control or front panel to begin dialing.Note: Placing a phone call from your cell phone will also initiate Bluetooth function.Press SELECT from Bluetooth mode to view recent calls dialed, received or missed while connected to the head unit. Turn the volume knob to cycle through the recent phone numbers. Press SELECT or to dial the number. To redial the last phone number, press two times from Bluetooth mode. Press or SELECT again to redial the phone number. Incoming phone calls will automatically appear on the display and a ring tone will be heard.Note: The volume of the ring tone depends on the volume level of the head unit and may not be heard if the volume is set to a low level or mute is activated.• Press to receive the incoming phone call.• Press and hold to refuse the incoming phone call.Note: If Auto Answer is set to ON in the setup menu, all phone calls will be received automatically. During an active phone call, press to end a phone call. If the phone call was received when listening to music in another mode, the head unit will resume the previous mode. The head unit supports A2DP wireless streaming audio from a Bluetooth mobile device directly to your head unit. The following functions can be used to control the music:• Press ll to skip to the next available audio track.• Press nn to skip to the previous audio track.• Press l/ II to toggle between play and pause during playback.            Disconnecting a DeviceManual DialingRecent Calls ListRedialing the last numberReceiving a Phone CallEnding a Phone CallStreaming AudioBluetooth  Operation
20XDMA760BTBluetooth  OperationThe XDMA760BT supports A2DP (advanced audio distribution profile) wireless streaming audio from your Bluetooth mobile device directly to your head unit. You can also control your music from the front panel of the head unit using AVRCP (audio video remote control profile).• To stream music to your head unit, your mobile device must support the A2DP and AVRCP Bluetooth profiles. Check the owner's manual of your mobile device for details.• Streaming audio must be enabled from your mobile device. This option will vary depending on the device. Some devices allow streaming audio to be disabled.After pairing, connecting and enabling streaming audio from a compatible mobile device, begin playing music using the music player on your mobile device. Once the music is playing, the following functions can be used to control the music:• The button will skip to the next available audio track.• The button will skip to the previous audio track.• The / button will toggle between play and pause during playback.Note: Some Bluetooth devices may not fully support these commands.Bluetooth ResetBluetooth Setup Menu OptionsStreaming Audio OperationllnnlIIResetting the Bluetooth module will remove the list of paired phones and delete the list of recent calls from memory.To reset Bluetooth, perform the following steps:1) Press SOURCE until the head unit is in Bluetooth mode.2) Press and hold MENU for 3 seconds to reset Bluetooth settings back to factory default.Compatibility Note:Due to the differences in Bluetooth technology, some mobile devices may be incompatible, function improperly or may not support all features when used with the XDMA760BT.Function Options ActionBluetooth BL'TOOTH (ON/OFF) Enables/disables Bluetooth functionality.Auto Connect AUTO CON (ON/OFF) Set to On to allow a Bluetooth device to connect automatically or Off to require manual connection.Auto Answer AUTO ANS (OFF/ON)When set to ON, incoming calls will all be answered after 2-3 rings. When set to off, the button must be pressed to answer incoming calls.Speaker Output BT SPRKS (FRONT/ALL)Set to FRONT to direct Bluetooth output to the front speakers only. Set to ALL to enable Bluetooth audio to output from all 4 speakers.
21XDMA760BTPandora OperationRequirementsUSB Connection Changing StationsShuffleSkipping Tracks  Play/PauseThumbs Up Thumbs DownDevice CompatibilityTroubleshootingControl for Pandora requires:• An iPhone device with a reliable data connection, or an iPod touch that is connected to wireless internet.• The Pandora App installed on the iPhone/iPod device.• An active account with Pandora. Sign up at www.pandora.com. • The USB sync cable that came with your iPod/iPhone device.Connect an iPod touch or iPhone device (required, sold sep-arately) to the USB port, using the USB sync cable included with your iPhone device.1. Press SELECT to display the Stations Menu. 2. Rotate the volume knob to choose to sort channels by date or alphabetically. 3. Press SELECT to confirm, then turn the volume knob to cycle through the list of stations.4. Press SELECT when the desired station is highlighted, and playback will begin.Note: Stations must be created on your account prior to connecting your iPod/iPhone device to the head unit.Press SELECT to display the Stations Menu. Choose “Shuffle” from the stations menu to shuffle songs from all of your stations.Press ll to skip the current song. Press l/ II to temporarily stop playback.Press l/ II again to resume playback.Press to tell Pandora you like the current track. Pandora will play more tracks with similar qualities.Press to tell Pandora you do not like the current track. Pandora will not play the current track again, and will avoid playing tracks with similar qualities.Refer to www.pandora.com/everywhere/mobile for devices compatible with the Pandora mobile application.Note: Pandora is an internet service, carrier and data charges may apply.
22XDMA760BTThis warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase.Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period.Who is covered? This warranty is extended to the original retail purchaser for products purchased from an authorized Dual dealer and used in the U.S.A.What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: software, installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. Specific license conditions and copyright notices for the software can be found via www.dualav.com.What to do? 1. Before you call for service, check the troubleshooting guide in your owner’s manual. A slight adjustment of any custom controls may save you a service call.2. If you require service during the warranty period, you must carefully pack the product (preferably in the original package) and ship it by prepaid transportation with a copy of the original receipt from the retailer to an authorized service center. 3. Please describe your problem in writing and include your name, a return UPS shipping address (P.O. Box not acceptable), and a daytime phone number with your shipment.4. For more information and for the location of the nearest authorized service center please contact us by one of the following methods:• Call us toll-free at 1-866-382-5476• E-mail us at cs@dualav.comExclusion of Certain Damages: This warranty is exclusive and in lieu of any and all other warranties, expressed or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose and any obligation, liability, right, claim or remedy in contract or tort, whether or not arising from the company’s negligence, actual or imputed. No person or representative is authorized to assume for the company any other liability in connection with the sale of this product. In no event shall the company be liable for indirect, incidental or consequential damages.Limited One-Year Warranty
23XDMA760BTProblem Cause ActionUnit will not turn on (no power)Yellow wire not connected or incorrect voltage Red wire not connected or incorrect voltageCheck connections for proper voltage (11-16VDC) Black wire not connected Check connection to groundFuse blown Replace fuseUnit has power (but no sound)Speaker wires not connected Check connections at speakersOne or more speaker wires touching each other or touching chassis groundInsulate all bare speaker wires from each other and chassis groundUnit blows fusesYellow or red wire touching chassis ground Check for pinched wireSpeaker wires touching chassis ground Check for pinched wireIncorrect fuse rating Use fuse with correct ratingExcessive skippingUnit is not mounted correctly or backstrap is not secureCheck mounting sleeve and backstrap supportPhysical defect in media (CD, CD-R or CD-RW) Check media for scratchesNO FILE appears on displayDisc read error Press eject or RESETFocus error or disc is upside down Press eject or RESETWMA file is protected by DRM (Digital Rights Management)Write disc using WMA files that are not protectedNo playable MP3/WMA files found on the deviceCheck the device for valid MP3/WMA filesCommunication error Remove and reconnect the deviceUnit will not accept a discCD mechanism position out of alignmentPress EJECT to reset CD mechanism positionCD transit screws still in place Remove 2 transit screws located on top of the unitNO SUPPORT appears on display An invalid ID3 tag version is present Version 1.0 to 2.4 ID3 tags are supported. Troubleshooting
24XDMA760BTFrequency response: 20Hz-20kHzChannel separation @ 1kHz: >65dBD/A converter: 1 BitTuning range: 87.5MHz-107.9MHzUsable sensitivity: 8.5dBf50dB quieting sensitivity: 10dBfStereo separation @ 1kHz: >30dBFrequency response: 30Hz-13kHzTuning range: 530kHz-1710kHzUsable sensitivity: 22uVFrequency response: 30Hz-2.2kHzSpeaker output impedance: 4-8 ohmsLine output voltage: 2 Volts RMSDimensions: 7" x 7" x 2" (178 x 178 x 50 mm)Design and specifications subject to change without notice.CD PlayerFM TunerAM TunerGeneralCEA-2006 Power Standard Specifications(reference: 14.4VDC +/- 0.2V, 20Hz-20kHz) Power Output: 18 Watts RMS x 4 channels at 4 ohms and < 1% THD+NSignal to Noise Ratio: 70dBA (reference: 1 watt into 4 ohms)Specifications
25XDMA760BTThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Compliance
Dual Electronics Corp.Toll Free: 1-866-382-5476Monday-Friday, 9AM-5PM, ESTwww.dualav.com©2015 Dual Electronics Corp. All rights reserved.iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod or iPhone may affect wireless performance.The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Namsung is under license. Pandora, the Pandora logo, and the Pandora trade dress are trademarks of Pandora Media, Inc., used with permission.Other trademarks and trade names are those of their respective owners.NSA0515-V01

Navigation menu