Fibar Group FGMS002 Motion Sensor User Manual FGMS 001 USA A v1 02 LQ

Download:
Mirror Download [FCC.gov]
Document ID	2604197
Application ID	EuP12XPkjvuujfwimltKcw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.49kB (406107 bits)
Date Submitted	2015-05-04 00:00:00
Date Available	2015-10-31 00:00:00
Creation Date	2015-04-30 10:32:11
Producing Software	Adobe PDF library 11.00
Document Lastmod	2015-04-30 10:32:11
Document Title	FGMS-001-USA-A-v1.02 LQ
Document Creator	Adobe Illustrator CC 2014 (Windows)

USA
© 2015 Fibar Group S.A. All rights reserved.
Distributed by Fibaro
1040 East Lake Ave, Glenview,
IL 60025, USA
www.fibaro.com
OPERATING MANUAL
FIBARO MOTION SENSOR
FGMS-001-USA-A-V1.02
The Fibaro Motion Sensor is a universal Z-Wave multi-sensor. Along
with detecting motion the device measures the temperature and light
intensity. The sensor has a built-in accelerometer to detect any
tampering of the device. The Fibaro Motion Sensor is battery powered device and designed to be installed quickly and easily on any
surface. The LED indicator signals motion, temperature level, operating mode and can be used to see if device is within the Z-Wave
network. The motion sensor can be used for lighting scenes and
presence monitoring systems.
SPECIFICATIONS
Power Supply:
CR123A battery, 3.0V DC
EU directives compliance:
RoHS 2011/65/EU
LVD 2006/95/EC
EMC 2004/108/EC
R&TTE 1999/5/EC
Recommended installation height:
2,4m
Operational Temperature:
0-40oC
Measured Temperature Range:
-20 to 100oC
Temperature Measuring
Accuracy:
0,5oC (within 0oC-40oC range)
Light Intensity Measuring Range:
0-32000 LUX
Radio Protocol:
Z-Wave
Radio Frequency:
868,4 or 869,8 MHz EU;
908,4 or 916 MHz US;
921,4 or 919,8 MHz ANZ;
869 MHz RU;
Range:
up to 50 m outdoors
up to 30 m indoors
(depending on terrain and
building structure)
CAUTION
When handled carelessly or used in non-specified
environment conditions, the device may not function
properly. It’s highly recommended to take all safety
precautions to ensure safety and property
protection.
CAUTION
Use only batteries recommended by the manufacturer and intended for use in the device. Using other
batteries can be considered as breach of warranty
terms.
IV. SENSOR INSTALLATION
VII. RESETTING THE FIBARO MOTION SENSOR
CAUTION
Read this manual before attempting to install the
device. Failure to observe recommendations included
in this manual may be dangerous or cause a violation
of the law. The manufacturer, Fibar Group S.A. will not
be held responsible for any loss or damage resulting
from not following the instructions of operating
manual.
CAUTION
Work within local code height requirements for
installation of the Fibaro Smoke Sensor. Take special
precautions during installation and use tools and
equipment in perfect working order. It’s recommended
to observe ladders, lifts and other obstacles.
Fibaro Motion Sensor reset procedure:
1) Make sure the battery works and is in place.
2) Press and hold the B-button for 4-6 seconds until the LED glows
yellow signaling the 2nd option of the menu mode.
3) Release the B-button.
4) Again, press the B-button briefly.
Successful reset will be confirmed with the LED changing colour to
red and fading.
CAUTION
Using batteries other than specified may result in
explosion.
Please use this procedure only in the event that the system primary
controller is missing or otherwise inoperable.
SENSOR
CAUTION
The Fibaro Motion Sensor is a battery-powered
device. Dispose of properly, observing environmental protection rules.
NOTE
The Fibaro Motion Sensor is a Security Enabled
Z-Wave Plus product and a Security Enabled
Z-Wave Controller must be used in order to fully
utilize the product.
Fibaro Motion Sensor has a bulit in motion detector, temperature
sensor and light intensity sensor, which make it a multi-channel
device. In the Home Center 2 menu it will be presented as three
devices, depending on the main controller software version. The
sensor supports the secure mode. In this mode messages are
encrypted, improving Z-Wave network safety level.
Diagram 2 - Motion detector, light sensor, LED diode.
I. GLOSSARY OF TERMS
• adding - Z-Wave device learning mode, allowing to add the device
to existing Z-Wave network.
• removing - Z-Wave device learning mode, allowing to remove the
device from existing Z-Wave network.
• association (linking devices) - direct control of other devices within
the Z-Wave network system.
• multi-channel association - controlling other multi-channel
devices within the Z-Wave network.
• control command - type of Z-Wave network command enforcing
change of device state.
• report command - type of Z-Wave network command holding an
additional information, e.g. alarm state or measured temperature.
• alarm command - type of Z-Wave network command holding a
warning of danger occurrence, e.g. fire alarm.
• multi-channel device - device having multiple endpoints - various
device functions.
Diagram 5 - Fibaro Motion Sensor’s proximity area.
The Fibaro Motion Sensor can be included into the Z-Wave network
by using the B-button.
1) Open the sensor’s casing by turning the cover counter-clockwise.
Enclosure lock is marked with a dot.
2) Unlock battery by removing “I'm ready” stripe.
3) Make sure the device is located within the direct range of the main
controller.
4) Set the main controller into learning mode (see main controller’s
operating manual).
5) Quickly, triple click the B-button - LED diode will glow blue to
confirm setting into learning mode.
6) Fibaro Motion Sensor will be detected and included into the
Z-Wave network. Wait for the main controller to configure the sensor.
7) If necessary, wake up the Motion Sensor by clicking the B-button.
8) Close the sensor’s casing and install the device in desired place.
1st Association Group „Lifeline” is a reporting group, assigned to
the device status. Main Z-Wave+ network controller should be added
to this group. The „Lifeline” group can handle only one device. If
Fibaro Motion Sensor operates in protected mode, outgoing
messages are always encrypted.
2nd Association Group „Motion” is assigned to the motion sensor.
At the moment of motion detection or alarm state cancellation, nodes
added to this group will receive control frames. The „Motion” group
can handle up to five devices (one or multi-channel). If Fibaro Motion
Sensor operates in protected mode, outgoing messages are
encrypted, depending on whether the added node also operates in
secure mode.
3rd Association Group „Tamper” is assigned to the tamper alarm.
Once tampering is detected or cancelled, nodes added to this group
will receive alarm frames. The „Tamper” group can handle up to five
devices (one or multi-channel). If Fibaro Motion Sensor operates in
protected mode, outgoing messages are always encrypted.
4th Association Group „Motion BC” is assigned to the motion
sensor. Once motion is detected or alarm state cancelled, nodes
added to this group will receive report frames. This group aims to
provide backward compatibility with controllers not supporting the
Z-Wave+ protocol. Only a main controller not supporting the
Z-wave+ protocol should be added to this group. The „Motion BC”
group can handle up to five devices (one or multi-channel). If Fibaro
Motion Sensor operates in protected mode, outgoing messages are
always encrypted.
5th Association Group „Tamper BC” is assigned to the tamper
alarm. Once tampering is detected or cancelled, nodes added to this
group will receive alarm frames. This group aims to provide
backward compatibility with devices not supporting the Z-Wave+
protocol. Only nodes not supporting the Z-wave+ protocol should be
added to this group. The „Tamper BC” group can handle up to five
devices (one or multi-channel). If Fibaro Motion Sensor operates in
protected mode, outgoing messages are always encrypted.
The Fibaro Motion Sensor allows for controlling 5 regular and 5
multichannel devices per an association group, out of which 1 field is
reserved for the Z-Wave network main controller.
X. EARTHQUAKE DETECTOR MODE
Fibaro Motion Sensor can be configured to work as a simple
earthquake detector, by setting the Parameter 24 value to 4. Reports
with scale of the vibrations (in the Modified Mercalli Scale) will be
sent at the time intervals specified in Parameter 22. First report will
be sent immediately after vibrations have been detected. The
minimum value of the vibrations, resulting in report being sent, can
be defined in Parameter 20. Once the vibrations cease, reports will
stop being sent. The Home Center 2 menu presents the earthquake
detector measurements in the following way:
3m
0m
7m
5m
Temperature sensor
Fibaro Motion Sensor has a built-in temperature sensor. Reports on
the current temperature level are always sent to main Z-Wave
network controller. Report can be triggered by the change in
temperature (parameter 60) or after a specified time (parameter 64).
0m
Diagram 1 - B-button.
Motion sensor
The primary function of Fibaro Motion Sensor is motion detection.
The detector is a passive IR sensor. Motion Sensor operating
parameters have been selected carefully and should not be changed
by the user. However, it is possible to change sensitivity of the device
by modifying parameter 1. You can also modify motion alarm
cancellation delay with parameter 6.
Light sensor
Fibaro Motion Sensor has a built-in light sensor. Reports on the
current light intensity are always sent to main Z-Wave network
controller. Report can be triggered by change in light intensity
(parameter 40) or after a specified time (parameter 42).
Diagram 3 - preparing Fibaro Motion Sensor for operation.
Tamper alarm
Fibaro Motion Sensor has a tamper alarm, used to signal an attempt
to dismantle the device. The main Z-Wave controller and other
Z-Wave network devices are notified about tampering. The
sensitivity of the tamper alarm may be modified in parameter 20.
CAUTION
Fibaro Motion Sensor may be included in protected
mode (Z-Wave network security mode). In this mode
communication takes place via encrypted
messages. This improves the operating safety and
reduces risk of unauthorized access to Z-Wave
network and devices working within its range.
Devices in protected mode can work together with
standard mode devices.
IX. ASSOCIATIONS
5m
7m
III. EXCLUDING SENSOR FROM THE Z-WAVE NETWORK
1) Make sure tampering the device will not result in undesirable
effects. Dismounting the sensor can trigger an alarm.
2) Open the sensor’s casing by turning the cover counter-clockwise.
Enclosure lock is marked with a dot.
3) Make sure the sensor's battery is unlocked.
4) Set the main controller into learning mode (see main controller’s
operating manual).
5) Quickly, triple click the B-button, located inside Fibaro Motion
Sensor’s casing. LED diode will glow blue confirming that the device
has sent the Node Info Z-Wave command frame.
Motion, temperature and light intensity values are presented in
Home Center 2 menu with the following icons:
Fibaro Motion Sensor’s detection area is shown in diagram #6.
Fibaro Motion Sensor has to be installed in a corner of the room or
perpendicularly to the doors.
Actual range of the sensor can be influenced by environment
conditions. If false motion alarms are reported, check for any moving
objects within the sensor’s detection area, such as trees blowing in
the wind, cars passing by, windmills. False motion alarms may be
caused by moving masses of air and heat as well. If the device
keeps on reporting false alarms, despite eliminating all of the
above-mentioned factors, install the device in another place.
I’M DY
II. Z-WAVE NETWORK INCLUSION
NOTE
Fibaro Motion Sensor capabilities will vary
depending on the Z-Wave network controller. Certain
functionalities of the Fibaro Motion Sensor may not
be supported by some controllers. To make sure
your Z-Wave network controller supports the Fibaro
Motion Sensor, get in touch with its manufacturer.
V. DETECTION AREA AND WORKING CONDITIONS
RE
B-BUTTON
NOTE
Device reset will not remove it from the Z-Wave
network main controller’s memory. However,
removing the device from the Z-Wave network will
reset Fibaro Motion Sensor automatically.
VIII. OPERATING WITHIN THE Z-WAVE NETWORK
TECHNICAL INFORMATION
- Compatible with any Z-Wave+ controller.
- Works with other Z-Wave network devices, but as a battery
device it doesn’t take part in signal routing.
- Supports protected mode (Z-Wave network security mode) with
AES-128 encryption.
- Detects motion using a passive IR sensor.
- Measures the temperature.
- Measures the light intensity.
- Easy installation on a wall or any surface.
- Protected against tampering and theft - once vibrations are
detected, the notification is sent to the main controller.
- Alarms of movement and temperature are signaled by LED diode
blinking.
- Simple earthquake detector mode.
The Fibaro Motion Sensor reset erases the memory, including all
information on the Z-Wave network and the main controller.
1) Include the device into the Z-Wave network (see p.II). Note that
the inclusion process may be performed ONLY in direct range of the
main controller.
2) Install the sensor’s holder in desired location.
3) Insert the Motion Sensor in its holder.
4) Test the sensor’s operation - check whether the LED diode
indicates motion detection.
5) Test the Z-Wave network assuring the device is within range.
Fibaro Motion Sensor allows for association of five groups:
STICKER
Diagram 6 - Fibaro Motion Sensor’s motion detection area.
VI. INSTALLATION NOTES
Diagram 4 - Fibaro Motion Sensor installation.
By using association with Fibaro’s devices the Fibaro Motion Sensor
may control another Z-Wave network device, e.g. a Dimmer, Relay
Switch, Roller Shutter, RGBW Controller, Wall Plug, or a scene
(scene only through the Home Center 2 main controller).
Fibaro Motion Sensor cannot be pointed at any source of heat (e.g.
radiators, fireplaces, cookers, etc.) or at any source of light (direct
sunlight, lamps).
It’s not recommended to install the Motion Sensor in places prone to
drafts and rooms with rapid fluctuations in air temperature. Sensor
can be mounted using the included screw or the sticker.
NOTE
Association allows for direct communication
between Z-Wave network devices. Main controller
does not take part in such communication. Using this
mechanism, Fibaro Motion Sensor may communicate with other devices even when the main controller
is damaged, e.g. in case of fire.
When Fibaro Motion Sensor operates in secure mode, outgoing
messages are encrypted, depending on whether the added node
also works in secure mode.
XI. SENSOR’S ORIENTATION IN SPACE
The Fibaro Motion Sensor has a built-in accelerometer. When the
value of parameter 24 is set to 2 or 3, Z-Wave network controller will
be informed on the Sensor’s orientation in space by sending report
after triggering tamper alarm.
XII. LED VISUAL INDICATIONS AND SETTINGS
The Fibaro Motion Sensor is equipped with a LED diode for
indicating sensor’s operating modes and alarms. In addition the LED
indicator may inform of the Z-Wave network range and the current
temperature.
LED indicator modes:
1) Motion Alarm’s colour will vary depending on the temperature. The
colour and the signaling mode can be set in parameter 80.
2) Tamper alarm is signaled with an alternating blinking in LAPD
colours (red - blue - white).
3) The Z-Wave Node Info command frame is signaled with glowing
in blue. Node Info command frame is sent each time the device
wakes up.
To enter MENU press and hold the B-button for 3 seconds. MENU
levels will be signaled with the LED colours:
- VIOLET - Z-Wave network range tester
- YELLOW - sensor reset.
XIII. Z-WAVE RANGE TEST
The Fibaro Motion Sensor has a built in Z-Wave network main
controller’s range tester. Follow the below instructions to test the
main controller’s range:
1) Press and hold the B-button for 2 to 4 seconds until the LED glows
violet.
2) Release the B-button.
3) Press the B-button again, briefly.
4) LED will indicate the Z-Wave network’s range (range signaling
modes described below).
5) To exit Z-Wave range test, press the B-button briefly.
Z-Wave range tester signaling modes:
LED indicator pulsing green - Fibaro Motion Sensor attempts to
establish a direct communication with the main controller. If a direct
communication attempt fails, sensor will try to establish a routed
communication, through other modules, which will be signaled by
LED indicator pulsing yellow.
LED indicator glowing green - Fibaro Motion Sensor communicates with the main controller directly.
LED indicator pulsing yellow - Fibaro Motion Sensor tries to
establish a routed communication with the main controller through
other modules (repeaters).
LED indicator glowing yellow - Fibaro Motion Sensor communicates with the main controller through the other modules. After 2
seconds the sensor will retry to establish a direct communication
with the main controller, which will be signaled with LED blinking in
green.
LED indicator pulsing violet - Fibaro Motion Sensor does
communicate at the maximum distance of the Z-Wave network. If
connection proves successful it will be confirmed with a yellow glow.
It’s not recommended to use the sensor at the range limit.
LED indicator glowing red - Fibaro Motion Sensor is not able to
connect to the main controller directly or through another Z-Wave
network device (repeater).
XIV. BATTERY USAGE TIPS
The Fibaro Motion Sensor’s battery life is approximately 2 years at
factory default settings. The current battery level is displayed in a
Home Center 2 interface. Red battery icon means the battery needs
replacement. In order to avoid tamper detection while replacing the
battery, remove association of the 2-nd association group and
reduce tamper sensitivity (parameter 20 value set to 0). If battery
discharges quickly, please check for the following conditions which
may result in reducing the battery life:
- Wake up interval is too short - it’s recommended to lengthen the
interval.
- Temperature and light intensity reports are sent too frequently modify the advanced configuration settings to decrease the
frequency.
- If associated devices or the Z-Wave network main controller are
disconnected from the power source it will cause the sensor to
frequently attempt to reconnect to those devices which will result in
shortening the battery life.
- If not necessary, operating in protected mode is not recommended.
Secure mode results in reduced battery life.
NOTE
The Fibaro Motion Sensor features remote software
updates. The functionality is supported by the Fibaro
Home Center 2 and may not be supported by other
controllers. During the software update process, the
sensor does NOT support alarm functions.
XV. ADVANCED CONFIGURATION
WAKE UP INTERVAL
At each wake up the Fibaro Motion Sensor communicates with the
main controller, updates parameters settings, association groups
and the software if necessary. The Motion Sensor will wake up at a
defined time interval and will ALWAYS try to communicate with the
main controller
Available settings: 1-65535 (1-65535 seconds).
Default setting: 7200 (7200 seconds).
CAUTION
It’s not recommended to set the value of Wake Up
interval below 3600 seconds. Short wake up interval
may shorten the battery life and delay the reports or
even make them impossible.
A single press of the B-button will always wake up the device.
Group 0. Motion - parameters of detecting and reporting
1. MOTION SENSOR’S SENSITIVITY
The lower the value, the more sensitive the PIR sensor.
Available settings: 8 - 255
Default setting: 10
Parameter size: 2 [byte]
2. MOTION SENSOR’S BLIND TIME (INSENSITIVITY)
Period of time through which the PIR sensor is “blind” (insensitive) to
motion. After this time period the PIR sensor will be again able to
detect motion. The longer the insensitivity period, the longer the
battery life. If the sensor is required to detect motion quickly, the time
period may be shortened. The time of insensitivity should be shorter
that the time period set in parameter 6 (cancellation delay).
Available settings: 0 - 15 (0,5 - 8 seconds)
Formula to calculate the time: time [s] = 0.5 x (value + 1)
Default setting: 15 (8 seconds)
Parameter size: 1 [byte]
3. PIR sensor’s “PULSE COUNTER”
Sets the number of moves required for the PIR sensor to report
motion. The higher the value, the less sensitive the PIR sensor. It’s
not recommended to modify this parameter settings.
Available settings: 0 - 3 (1 - 4 pulses)
Formula to calculate the number of pulses: pulses = (value + 1)
Default setting: 1 (2 pulses)
Parameter size: 1 [byte]
4. PIR sensor’s “WINDOW TIME”
Period of time during which the number of moves set in parameter 3
must be detected in order for the PIR sensor to report motion. The
higher the value, the more sensitive the PIR sensor. It’s not
recommended to modify this parameter setting.
Available settings: 0 - 3
Formula to calculate the time: time [s] = 4 x (value + 1)
Default setting: 2 (12 seconds)
Parameter size: 1 [byte]
6. MOTION ALARM CANCELLATION DELAY
Motion alarm will be cancelled in the main controller and the
associated devices after the period of time set in this parameter. Any
motion detected during the cancellation delay time countdown will
result in the countdown being restarted. In case of small values,
below 10 seconds, the value of parameter 2 must be modified (PIR
sensor’s “Blind Time”).
Available settings: 1 - 32767 (1-32767 seconds)
Default setting: 30 (30 seconds)
Parameter size: 2 [byte]
8. PIR SENSOR OPERATING MODE
The parameter determines the part of day in which the PIR sensor
will be active. This parameter influences only the motion reports and
associations. Tamper, light intensity and temperature measurements
will be still active, regardless of this parameter settings.
0 - PIR sensor always active
1 - PIR sensor active during the day only
2 - PIR sensor active during the night only.
Default setting: 0
Parameter size: 1 [byte]
9. NIGHT / DAY
The parameter defines the difference between night and day, in
terms of light intensity, used in parameter 8.
Available settings: 1 - 32767 (1-32767 lux)
Default setting: 200 (200 lux)
Parameter size: 2 [byte]
Group 10. Motion - associations
12. BASIC COMMAND CLASS FRAMES CONFIGURATION
The parameter determines the command frames sent in 1-st
association group, assigned to PIR sensor.
0 - BASIC ON and OFF command frames sent in Basic Command
Class.
1 - only the BASIC ON command frame sent in Basic Command
Class.
2 - only the BASIC OFF command frame sent in Basic Command
Class.
Values of BASIC ON and BASIC OFF command frames may be
modified by dedicated parameters (14 and 16).
Default setting: 0
Parameter size: 1 [byte]
14. BASIC ON command frame value
The command frame sent at the moment of motion detection.
Further motion detections, during the cancellation time, will not result
in sending the association.
The value other than 0 allows to turn ON an associated device. In
case of the Dimmer, the value of 255 means turning ON at the last
memorized state, e.g. the Dimmer turned ON at 30% and turned
OFF using the value of 255, and then turned OFF, will be turned ON
at 30%, i.e. the last memorized state.
Available settings: 0 - 255
Default setting: 255
Parameter size: 2 [byte]
16. BASIC OFF command frame value
The command frame sent at the moment of motion alarm
cancellation, after cancellation delay time specified in parameter 6.
The value of 0 allows to turn a device OFF while the value of 255
allows to turn ON a device. In case of the Dimmer, the value of 255
means turning ON at the last memorized state, e.g. the Dimmer
turned ON at 30% and turned OFF using the value of 255, and then
turned OFF, will be turned ON at 30%, i.e. the last memorized state.
Available settings: 0 - 255
Default setting: 0
Parameter size: 2 [byte]
Group 20. Tamper - parameters of detecting and reporting
20. TAMPER SENSITIVITY
The parameter determines the chages in forces acting on the Fibaro
Motion Sensor resulting in tamper alarm being reported - g-force
acceleration.
Available settigs: 0 - 121 (0,08 - 2g; multiply by 0,016g;
0 = tamper inactive)
Default setting: 15 (0,320g)
Parameter size: 1 [byte]
22. TAMPER ALARM CANCELLATION DELAY
Time period after which a tamper alarm will be cancelled. Another
tampering detected during the countdown to cancellation will not
extend the delay.
Available settings: 1 - 32767 (1-32767 seconds)
Default setting: 30 (seconds)
Parameter size: 2 [byte]
24. TAMPER OPERATING MODES
The parameter determines the behaviour of tamper alarm and how it
reports. It is an advanced feature serving much more functions than
just detection of tampering.
0 – Only tamper (default)
1 – Tamper and earthquake detector. Function may be used as a
simple seismograph. Two reports including the strength of shock are
always sent. First, right after the detection and second (value=0)
after tamper alarm cancellation delay time.
2 – Tamper and orientation in space. Three reports are sent right
after tamper alarm cancellation delay time.
Default setting: 0
Parameter size: 1 [byte]
25. TAMPER CANCELLATION REPORTS
0 – Do not send tamper cancellation report
1 – Send tamper cancellation report
Default setting: 1
Parameter size: 1 [byte]
28. TAMPER ALARM BROADCAST MODE
The parameter determines whether the tamper alarm frame will or
will not be sent in broadcast mode. Alarm frames sent in broadcast
mode can be received by all of the devices within communication
range (if they accept such frames). When Fibaro Motion Sensor is
operating in protected mode (secure mode), the value should remain
default. Device operating in protected mode doesn’t send frames in
broadcast mode.
0 - Tamper alarm reported to association groups.
1 - Tamper alarm reported in broadcast mode to 3rd association
group.
Default setting: 0
Parameter size: 1 [byte]
29. TAMPER ALARM BROADCAST MODE
The parameter determines whether the tamper alarm frame will or
will not be sent in broadcast mode. Alarm frames sent in broadcast
mode may be received by all of the devices within communication
range (if they accept such frames). When Fibaro Motion Sensor is
running in protected mode (secure mode), the value should remain
default. Device operating in protected mode do not send frames in
broadcast mode.
0 - Tamper alarm reported to association groups.
1 - Tamper alarm reported in broadcast mode to 5th association
group.
Default setting: 0
Parameter size: 1 [byte]
Group 40. Light sensor - parameters of detecting and reporting
40. ILLUMINATION REPORT THRESHOLD
The parameter determines the change in light intensity level
resulting in illumination report being sent to the main controller.
Available settings: 0 - 32767 (1-32767 lux; 0=reports are not sent)
Default setting: 200 (200 lux)
Parameter size: 2 [byte]
42. ILLUMINATION REPORTS INTERVAL
Time interval between consecutive illumination reports. The reports
are sent even if there are no changes in the light intensity.
Available settings: 0 - 32767 (1-32767 seconds; 0 = no reports)
Default setting: 0 (no reports)
Parameter size: 2 [byte]
CAUTION
Frequent reports will shorten the battery life.
Parameter value under 5 may result in blocking the
temperature reports.
Group 60. Temperature sensor - parameters of detecting and reporting
60. TEMPERATURE REPORT THRESHOLD
The parameter determines the change in level of temperature
resulting in temperature report being sent to the main controller.
Available settings: 0 - 255 (0,1-25,5oC,; 0 = reports are not sent)
Default setting: 10 (1oC)
Parameter size: 2 [byte]
62. INTERVAL OF TEMPERATURE MEASURING
The parameter determines how often the temperature will be
measured. The shorter the time, the more frequently the temperature
will be measured, but the battery life will shorten.
Available settings: 0 - 32767 (1 - 32767 seconds; 0 = temperature
will not be measured)
Default setting: 900 (900 seconds)
Parameter size: 2 [byte]
CAUTION
When parameter value is set to 0, the temperature
measurements may be performed at the device
wake-up.
64. TEMPERATURE REPORTS INTERVAL
The parameter determines how often the temperature reports will be
sent to the main controller.
Available settings: 0 - 32767 (1 - 32767 seconds; 0 = no reports)
Default setting: 0 (no reports)
Parameter size: 2 [byte]
CAUTION
Frequent reports will shorten the battery life.
Parameter value under 5 may result in blocking the
illumination reports.
66. TEMPERATURE OFFSET
The value to be added to the actual temperature, measured by the
sensor (temperature compensation).
Available settings: -1000 - 1000 (-100oC – 100oC)
Default setting: 0 (0oC)
Parameter size: 2 [byte]
Group 80. LED indications
80. LED SIGNALING MODE
The parameter determines the way in which LED diode behaves
after motion has been detected.
Values from 1 to 9 = single long blink at the moment of reporting
motion. No other motion will be indicated until alarm is cancelled.
Values from 10 to 18 = single long blink at the moment of reporting
motion and one short blink each time the motion is detected again.
Values from 19 to 26 = single long blink at the moment of reporting
motion and two short blinks each time the motion is detected again.
0. LED inactive.
1. LED colour depends on the temperature. Set by parameters
86 and 87.
2. Flashlight mode - LED glows in white for 10 seconds.
3. White.
4. Red.
5. Green.
6. Blue.
7. Yellow.
8. Cyan.
9. Magenta.
10. LED colour depends on the temperature. Set by parameters
86 and 87.
11. Flashlight mode - LED glows in white through 10 sec. Each
next detected motion extends the glowing by next 10 seconds.
12. White.
13. Red.
14. Green.
15. Blue.
16. Yellow.
17. Cyan
18. Magenta
19. LED colour depends on the temperature. Set by parameters
86 and 87.
20. White
21. Red
22. Green
23. Blue
24. Yellow
25. Cyan
26. Magenta
Default setting: 10
Parameter size: 1 [byte]
81. LED BRIGHTNESS
The parameter determines the brightness of LED when indicating
motion.
Available settings: 0 - 100 (1 - 100%; 0 = brightness determined by
the ambient lighting - see parameters 82 and 83)
Default setting: 50 (50%)
Parameter size: 1 [byte]
82. AMBIENT ILLUMINATION LEVEL BELOW WHICH LED
BRIGHTNESS IS SET TO 1%
The parameter is relevant only when the parameter 81 is set to 0.
Available settings: 0 to parameter 83 value (0-32766 lux)
Default setting: 100 (100 lux)
Parameter size: 2 [byte]
83. AMBIENT ILLUMINATION LEVEL ABOVE WHICH LED
BRIGHTNESS IS SET TO 100%
The parameter is relevant only when the parameter 81 is set to 0.
Available settings: parameter 82 value to 32767 (1-32767 lux)
Default setting: 1 000 (1 000 lux)
Parameter size: 2 [byte]
CAUTION
The value of parameter 83 must be higher than the
value of parameter 82.
86. MINIMUM TEMPERATURE RESULTING IN BLUE LED
ILLUMINATION
This parameter is relevant only when parameter 80 has been
properly configured.
Available settings: 0 to parameter 87 value (0-255oC)
Default setting: 18 (18oC)
Parameter size: 2 [byte]
87. MAXIMUM TEMPERATURE RESULTING IN RED LED
ILLUMINATION
This parameter is relevant only when parameter 80 has been
properly configured.
Available settings: parameter 86 value to 255 (0-255oC)
Default setting: 28 (28oC)
Parameter size: 2 [byte]
CAUTION
The value of parameter 87 must be higher than the
value of parameter 86.
89. LED INDICATING TAMPER ALARM
Indicating mode resembles a police car (white, red and blue).
0 - LED does not indicate tamper alarm.
1 - LED indicates tamper alarm.
Default setting: 1
Parameter size: 1 [byte]
XVI. GUARANTEE
1. The Guarantee is provided by FIBAR GROUP S.A. (hereinafter
"Manufacturer"), based in Poznan, ul. Lotnicza 1; 60-421 Poznan,
entered in the register of the National Court Register kept by the
District Court in Poznań, VIII Economic Department of the National
Court Register, no. 370151, NIP 7811858097, REGON: 301595664.
2. The Manufacturer is responsible for equipment malfunction
resulting from physical defects (manufacturing or material) of the
Device for 12 months from the date of its purchasing.
3. During the Guarantee period, the Manufacturer shall remove any
defects, free of charge, by repairing or replacing (at the sole
discretion of the Manufacturer) any defective components of the
Device with new or regenerated components, that are free of
defects. When the repair impossible, the Manufacturer reserves the
right to replace the device with a new or regenerated one, which
shall be free of any defects and its condition shall not be worse than
the original device owned by the Customer.
4. In special cases, when the device cannot be replaced with the
device of the same type (e.g. the device is no longer available in the
commercial offer), the Manufacturer may replace it with a different
device having technical parameters similar to the faulty one. Such
activity shall be considered as fulfilling the obligations of the
Manufacturer. The Manufacturer shall not refund money paid for the
device.
5. The holder of a valid guarantee shall submit a guarantee claim
through the guarantee service. Remember: before you submit a guarantee claim, contact our technical support using telephone or
e-mail. More than 50% of operational problems is resolved remotely,
saving time and money spent to initiating guarantee procedure. If
remote support is insufficient, the Customer shall fill the guarantee
claim form (using our website - www.fibaro.com) in order to obtain
claim authorization. When the guarantee claim form is submitted correctly, the Customer shall receive the claim confirmation with an
unique number (Return Merchandise Authorization -RMA).
6. The claim may be also submitted by telephone. In this case, the
call is recorded and the Customer shall be informed about it by a
consultant before submitting the claim. Immediately after submitting
the claim, the consultant shall provide the Customer with the claim
number (RMA-number).
7. When the guarantee claim form is submitted correctly, a
representative of the Authorised Guarantee Service (hereinafter as
"AGS") shall contact the Customer.
8. Defects revealed within the guarantee period shall be removed
not later than 30 days from the date of delivering the Device to AGS.
The guarantee period shall be extended by the time in which the
Device was kept by AGS.
9. The faulty device shall be provided by the Customer with complete
standard equipment and documents proving its purchase.
10. Parts replaced under the guarantee are the property of the
Manufacturer. The guarantee for all parts replaced in the guarantee
process shall be equal to the guarantee period of the original device.
The guarantee period of the replaced part shall not be extended.
11. Costs of delivering the faulty device shall be borne by the
Customer. For unjustified service calls, the Service may charge the
Customer with travel expenses and handling costs related to the
case.
12. AGS shall not accept a complaint claim only when:
• the Device was misused or the manual was not observed,
• the Device was provided by the Customer incomplete, without
accessories or nameplate,
• it was determined that the fault was caused by other reasons than
a material or manufacturing defect of the Device
• the guarantee document is not valid or there is no proof of
purchase,
13. The Manufacturer shall not be liable for damages to property
caused by defective device. The Manufacturer shall not be liable for
indirect, incidental, special, consequential or punitive damages, or
for any damages, including, inter alia, loss of profits, savings, data,
loss of benefits, claims by third parties and any property damage or
personal injuries arising from or related to the use of the Device.
14. The guarantee shall not cover:
• mechanical damages (cracks, fractures, cuts, abrasions, physical
deformations caused by impact, falling or dropping the device or
other object, improper use or not observing the operating manual);
• damages resulting from external causes, e.g.: flood, storm, fire,
lightning, natural disasters, earthquakes, war, civil disturbance, force
majeure, unforeseen accidents, theft, water damage, liquid leakage,
battery spill, weather conditions, sunlight, sand, moisture, high or low
temperature, air pollution;
• damages caused by malfunctioning software, attack of a computer
virus, or by failure to update the software as recommended by the
Manufacturer;
• damages resulting from: surges in the power and/or telecommunication network, improper connection to the grid in a manner
inconsistent with the operating manual, or from connecting other
devices not recommended by the Manufacturer.
• damages caused by operating or storing the device in extremely
adverse conditions, i.e. high humidity, dust, too low (freezing) or too
high ambient temperature. Detailed permissible conditions for
operating the Device are defined in the operating manual;
• damages caused by using accessories not recommended by the
Manufacturer
• damages caused by faulty electrical installation of the Customer,
including the use of incorrect fuses;
• damages caused by Customer's failure to provide maintenance
and servicing activities defined in the operating manual;
• damages resulting from the use of spurious spare parts or
accessories improper for given model, repairing and introducing
alterations by unauthorized persons;
• defects caused by operating faulty Device or accessories.
15. The scope of the guarantee repairs shall not include periodic
maintenance and inspections, in particular cleaning, adjustments,
operational checks, correction of errors or parameter programming
and other activities that should be performed by the user (Buyer).
The guarantee shall not cover natural wear and tear of the Device
and its components listed in the operating manual and in technical
documentation as such elements have a defined operational life.
16. If a defect is not covered by the guarantee, the Manufacturer
reserves the right to remove such defect at its sole discretion,
repairing the damaged or destroyed parts or providing components
necessary for repair or replacement.
17. This guarantee shall not exclude, limit or suspend the Customer
rights when the provided product is inconsistent with the purchase
agreement.
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO
OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES OR
MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S
AUTHORITY TO OPERATE THE EQUIPMENT.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation. This equipment
has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy. If not installed and
used in accordance with the instructions, it may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Legal Notices
All information, including, but not limited to, information regarding the
features, functionality, and/or other product specification are subject
to change without notice. Fibaro reserves all rights to revise or
update its products, software, or documentation without any
obligation to notify any individual or entity.
Fibaro, Fibar Group logo, and Fibaro Motion Sensor are trademarks
of Fibar Group S.A. All other brands and product names referred to
herein are trademarks of their respective holders.
Disclaimer
The information contained herein is provided in connection with
Fibaro products. No license, expressed or implied by estoppel or
otherwise, to any intellectual property rights is granted by this
documents.
This documentation may contain references to third-party sources of
information, hardware or software, products or services (“collectively
the “Third-Party Products or Services”). Fibaro does not control the
Third-Party Products or Services and is not responsible for any
Third-Party Products or Services.
Except as provided above or except to the extent prohibited by
applicable law, Fibaro shall not be liable for any incidental or
consequential damages caused by the breach of any express or
implied warranty. Fibaro assumes no liability whatsoever, and Fibaro
disclaims any express or implied warranty, relating to the sale and/or
use of the Fibaro products, including, but to limited to, liabilities
and/or warranties relating to fitness for a particular purpose,
merchantability, and/or infringement of any patent, copyright and/or
other intellectual property right.
Except to the extent prohibited by applicable law, Fibaro’s liability
shall not exceed the price paid for the Fibaro products from direct,
indirect, special, incidental or consequential damages resulting from
the sue of the products, its accompanying software, or product
specifications, manuals, installation guides and/or any other
documentation.
Some states, provinces or jurisdictions do not allow the exclusion or
limitation of incidental or consequential damages or other limitations
on warranties, so the above limitations or exclusion may not apply to
you. You may also have other rights that vary from state to state or
province to province.
This Device may be used with all devices
certified with Z-Wave certificate and should be
compatible with such devices produced by
other manufacturers.
Any device compatible with Z-Wave may be added
to Fibaro system.
FIBAR GROUP
FIBARO
In case of any technical questions contact
customer service centre in your country.
www.fibaro.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c014 79.156821, 2014/08/29-03:07:50
Format                          : application/pdf
Title                           : FGMS-001-USA-A-v1.02 LQ
Metadata Date                   : 2015:04:30 10:32:11+02:00
Modify Date                     : 2015:04:30 10:32:11+02:00
Create Date                     : 2015:04:30 10:32:11+02:00
Creator Tool                    : Adobe Illustrator CC 2014 (Windows)
Thumbnail Width                 : 144
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 15325 bytes, use -b option to extract)
Instance ID                     : uuid:54982a36-41b9-45dc-8480-009d1014ab67
Document ID                     : xmp.did:237b8180-af73-2349-9b87-9ada6f507210
Original Document ID            : uuid:5D20892493BFDB11914A8590D31508C8
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:c7be956e-a4e8-8d46-98b8-3c09cfa5ee79
Derived From Document ID        : xmp.did:c7be956e-a4e8-8d46-98b8-3c09cfa5ee79
Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8
Derived From Rendition Class    : proof:pdf
History Action                  : saved, saved
History Instance ID             : xmp.iid:FB7F117407206811822AAD98C13933C3, xmp.iid:237b8180-af73-2349-9b87-9ada6f507210
History When                    : 2011:09:02 11:02:22+02:00, 2015:04:30 10:32:03+02:00
History Software Agent          : Adobe Illustrator CS5, Adobe Illustrator CC 2014 (Windows)
History Changed                 : /, /
Manifest Link Form              : EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference, EmbedByReference
Manifest Reference File Path    : C:\Users\USER\Pictures\zplus_bw.jpg, D:\Nomenklatura\Grafiki\seismo5.jpg, motion_sensor_temp.jpg, motion_sensor_swiatlo_eng.jpg, oko-on.jpg, oko-off.jpg
Manifest Reference Document ID  : adobe:docid:photoshop:9f868e71-7bbe-11e4-b01d-f70e425e780b, adobe:docid:photoshop:bc09af58-ce35-11e4-8d14-82202672555d
Manifest Reference Instance ID  : xmp.iid:e0f00e78-c9e5-9646-9b17-5abf50c19c24, xmp.iid:46a2a871-d7cb-e44e-a234-f9c1310cd0da
Ingredients File Path           : C:\Users\USER\Pictures\zplus_bw.jpg, D:\Nomenklatura\Grafiki\seismo5.jpg, motion_sensor_temp.jpg, motion_sensor_swiatlo_eng.jpg, oko-on.jpg, oko-off.jpg
Ingredients Document ID         : adobe:docid:photoshop:9f868e71-7bbe-11e4-b01d-f70e425e780b, adobe:docid:photoshop:bc09af58-ce35-11e4-8d14-82202672555d
Ingredients Instance ID         : xmp.iid:e0f00e78-c9e5-9646-9b17-5abf50c19c24, xmp.iid:46a2a871-d7cb-e44e-a234-f9c1310cd0da
Startup Profile                 : Print
Has Visible Overprint           : False
Has Visible Transparency        : True
N Pages                         : 1
Max Page Size W                 : 352.999992
Max Page Size H                 : 249.999571
Max Page Size Unit              : Millimeters
Font Name                       : Arial-BoldMT, ArialMT, HelveticaNeueCE-Roman, BellMTBold, MyriadPro-Regular
Font Family                     : Arial, Arial, Helvetica CE 55 Roman, Bell MT, Myriad Pro
Font Face                       : Bold, Regular, Regular, Bold, Regular
Font Type                       : Open Type, Open Type, TrueType, Open Type, Open Type
Font Version                    : Version 6.87, Version 6.87, 001.001, Version 1.51, Version 2.106;PS 2.000;hotconv 1.0.70;makeotf.lib2.5.58329
Font Composite                  : False, False, False, False, False
Font File Name                  : arialbd.ttf, arial.ttf, Helvetica Neue CE 55 Roman.ttf, BELLB.TTF, MyriadPro-Regular.otf
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Groups Group Name        : Brights
Swatch Groups Group Type        : 1
Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0
Swatch Groups Colorants Mode    : CMYK
Swatch Groups Colorants Type    : PROCESS
Swatch Groups Colorants Cyan    : 60.000000
Swatch Groups Colorants Magenta : 90.000000
Swatch Groups Colorants Yellow  : 0.003100
Swatch Groups Colorants Black   : 0.003100
Producer                        : Adobe PDF library 11.00
Page Count                      : 2
Creator                         : Adobe Illustrator CC 2014 (Windows)

EXIF Metadata provided by EXIF.tools