Fieldpiece Instruments 002 Wireless Module User Manual
Fieldpiece Instruments, Inc. Wireless Module Users Manual
Users Manual
2ALHR002 Module User's Manual 1. Features ‐ On‐chip low power microcontroller ‐ 128KB of In‐system programmable flash ‐ 8KB SRAM ‐ On board crystal and PFA Antenna 2. Application ‐ Mobile device accessories (Android/ iOS) ‐ Wireless data communication ‐ Remote sensors 3. Pin definition Pin No. Description Pin Type Functions BLE_RX Digital I/O UART RX BLE_TX Digital I/O UART TX WAKE_UP Output Digital I/O STATUS Input Digital I/O GND Digital I/O GND V+ Digital I/O VDD BLE_EN Digital I/O VDD Enable 4. How to use: ‐ Before sending any UART Command, "WAKE_UP 1 0" must be done by external MCU. ‐ If the CC2640 module is connected to Smart Devices (Android/ iOS), the pin STATUS will be logic "1" to inform external MCU. ‐ Beacon ‐ 1. Send Command 'D'/'P' to send live measured data from external through Beacon. 2. This is default mode, and 2ALHR002 module send data only. Cannot receive any data. BLE ‐ 1. Send Command 'M' to switch mode from Beacon to BLE. 2. After the mode switch successfully, the external MCU can receive data from Smart phone. Receiver 1. Send Command 'A'/'B' to switch mode from Beacon to Receiver. 2. Only specific Beacon data can be received, and the external MCU receives the data from UART 5. Protocol: ‐ UART Baud Rate: 115200, 8, N, 1 ‐ Commands 'D': Send Measured Data External MCU 2ALHR002 Module Starter Len OP Battery Data CK End (0D 0A)h External MCU 2ALHR002 Module Starter Len OP Indi CK End (0D 0A)h 'P': Send Product Information External MCU 2ALHR002 Module Starter Len OP External MCU 2ALHR002 Module FP Prod. S/N Cal. Date CK End (0D 0A)h Starter Len OP Indi CK End (0D 0A)h 'M': Mode Switch External MCU 2ALHR002 Module Starter Len OP S/N CK End (0D 0A)h External MCU 2ALHR002 Module Starter Len OP Indi CK End (0D 0A)h 'A': Scan Product Information External MCU VEABT001 Module Starter Len '#' OP CK 'A' End (0D 0A)h External MCU VEABT001 Module Starter Len '>' OP SN APO Batt RSSI CK 'A' End (0D 0A)h 'B': Scan Measured Data External MCU VEABT001 Module Starter Len '#' OP SN CK 'B' End (0D 0A)h External MCU VEABT001 Module Starter '>' Len OP APO Batt Data RSSI CK 'B' This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a End (0D 0A)h residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). End Product Labeling This transmitter module is authorized only for use in devices. The final end product must be labeled in visible area with the following: “Contains FCC ID: 2ALHR002” ” End Product Manual Information The user manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter.” This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users. As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). in conjunction with any other antenna or transmitter.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : PCUser Create Date : 2017:05:22 13:44:08+08:00 Modify Date : 2017:06:07 10:28:57+08:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2017:06:07 10:28:57+08:00 Producer : Acrobat Distiller 11.0 (Windows) Format : application/pdf Title : Microsoft Word - 2ALHR002 Module User's Manual.docx Creator : PCUser Document ID : uuid:c08ee7a5-99d9-4bbe-b9d9-c21f462e15a2 Instance ID : uuid:f8945e7e-3d3b-471f-872f-b43cca376119 Page Count : 4EXIF Metadata provided by EXIF.tools