Filser Electronic ATR57COM Aeronautical Transceiver User Manual
Filser Electronic GmbH Aeronautical Transceiver
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 74841 |
| Application ID | uPQUjYqf6nnB1LFPAEfUUw== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 19.78kB (247207 bits) |
| Date Submitted | 1999-12-08 00:00:00 |
| Date Available | 2000-07-06 00:00:00 |
| Creation Date | 2001-05-09 07:00:01 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-05-09 07:00:02 |
| Document Title | user manual |
Filser EledronTc’GmbH Gewerbestralse 2 86875 Waal ATR 57 COM . MEN - VOL ‘ SD User manual Filser Electronle/GmbH Gewerbestralze 2 86875 Waal Contents 3.1 3.2 3.3 4.1 4.2 4.3 4.4 4.5 4.6 4.7 USER INTERFACE DISPLAY lNSTALLATION Panel installation Installation of the antenna Pin-layout PUTTING INTO OPERATION ON-switch Volume regulation Squelch level regulation Memory selector Selecting and storing a frequency Low-battery Losing frequency TRANSMITTING TECHNICAL REFERENCE Gib“ on 10 10 11 Filser EIectronlffimbH Gewerbestralle 2 86875 Waal 1 User interface Volume / squelch push—button ON / OFF switch MHzI kHz push-button Tuningknob for volume, squelch and selected frequency Change selected frequency to active frequency Store-button Select stored frequency NQP‘PPNr‘ Filser Electronic/GmbH Gewerbestratze 2 86875 Waal 3 Installation 3.1 Panel installation The ATR 57 is fixed in the panel with the four screws in instrument head. The cut-out diameter for placing the ATR 57 in the panel is standard 57mm. Lg One should lookout for a place in the panel which provides easy installing, a good view and reachability for the pilot sitting in normal position. Avoid mounting near hot places. So you do not need any external cooling device like a fan or similar. One should pay attention having enough space behind the backside of the ATR 57 for connectors and cables. The cable harness should be as short as possible. Avoid cable run near strong noise sources like the ignition coil, light dynamo or battery charger. This can cause a low frequency noise on the speaker. Your service company provides all needed cables, the connectors are delivered with your ATR 57. Filser Electronk/GmbH GewerbestraBe 2 86875 Waal 3.2 Installation of the antenna The ATR 57 works with a normal SOQ-COM-antenna. Polarization must be vertical. A whip antenna (aerial) is not necessary. Using a broad band COM-antenna provides a higher efficiency over the frequency band. One should fix the antenna corresponding to manufacturers advises. Some important things are listed below: 0 Unsymmetrical antennas (e.g. M4-Antenna) should be mounted on plane metal surfaces or metal plates of at least 50 x 50cm. 0 The antenna should have the maximal possible distance to motor, propeller and so on. This avoids getting modulation on your signal. 0 Again the COM-antenna should have the maximal possible distance to the NAV-antenna in order to avoid inter- ferences. ’ Filser Elemmm‘c’GmbH Gewerbestmfle 2 86875 Weal T ‘ 32:5 Eli ‘u_ F. 223 , 24:85? a: 63m: 2 so 92 Q6 N m: 399; ion} S 2538: , .§§§ N 2353: m?“ 39»; ii! £832. / / Qniin 7 Filser ElectroniTs/GmbH Gewerbestralle 2 86875 Waal 4 Putting into operation One will find all elements for operating the radio on the frontplate. 4.1 ON-switch The ,,ON-OFF“-switch (2) is on the left side in the middle. The radio is active, when the switchposition is ,,0N“ (upper side). Maxim Push one time the Volume/Squelch push-button (1) (located on the upper left side) to get into the volume mode. By turning the tuning knob (4) one can change the volume. The device will leave the volume mode, when there is no change for some seconds. The selected level is active only until the ATR 57 is switched off. To use this level as switch on default, push the store button (6) while the device is in the volume mode. For confirmation the ATR 57 shows ,,ST“ in its display. 4.3 Sguelch level regulation Push two times the Volume/Squelch push-button (1), to get into the squelch mode, then follow the instructions, listed in chapter 4.2.. Filser Eiectroriié’Gmbi—i Gewerbestrarse 2 66875 Waal MM The memory selector (7) is located in the upper middle. It is used for selecting previous stored frequencies or for saving a frequency on one of the 9 possible places, Between place 9 and 1 (the white line on the memory selector shows downward) one will find the operation mode for selecting a frequency and changing it to active. Mummy Turn the memory selector in the position between memory place 1 (M1) and 9 (M9) (the white line on the memory selector shows downward). In the first line of the display one can read the actual active frequency, in the second line is displayed the changeable frequency. To change between the MHz- and kHz-range use button (3), this is the down left-handed button. A small arrow (9) shows the actual changed range. Now you can change the value of the selected range by using the tuning knob (4). With the down right-handed button (5) this new frequency can be activated. Now it is displayed in the first line, the old active frequency is disactivated and written in the second line. Turn the memory selector (7) onto the place, you want the new frequency to be saved, press the store button (6), ready. 4.6 Low-battery If the battery voltage comes below 10,5V a blinking "B“ will be shown in upper left corner of the display. Now a regular operation of the device can not longer be warrented. Filser Electronic/GmbH Gewerbestraile 2 86875 Waal ' 4.7 Losing freguency If the actual used frequency has an untolerable difference to the displayed frequency a "-" (12) will appear in the upper right corner of the display. In this case the ATR 57 is working not properly and must be returned to the manufacturer. Notice: Sometimes the "-" may be shown, but it disappears when the frequency is changed or the device is switched off and on. This effect is due to strong noise from outside the ATR 57. This is M malfunktion of the ATR 57 5 Transmitting By using the transmitting key (PTT), the ATR 57 will change to the transmitting mode on the actual frequency shown in the upper line of the display. As long as the transmission takes place a "T" will be shown instead of the decimal point between the MHz- and kHz-value of the actual frequency (upper line), to control the proper function of the device. If the actual used frequency has an untolerable difference to the displayed frequency a - (12) will appear in the upper right corner of the display. In this case there will be no transmission. Filser EIectroniE’CmbH GewerbesiraBe 2 86875 Waal 7 Technical reference Frequency range: 118,000 136,975 MHz Quantity of channels: 760 1Channel spacing: 25 kHz Modulation: AM DSB, 70% modulation Operation modus: alternate talking on one frequency HF-output power: > 1 Watt NF-output power: 1 Watt Voltage: 10,5 V up to 16 V Current carrying: recieving 100 mA, , > g 7 7 7 f trane itting 1 A ‘ Dimensions: 5le 57 x 160mm Weight: 500 9 Certification: Reg TP 321 ZV 034
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:05:09 07:00:01 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:05:09 07:00:02-04:00 Page Count : 10EXIF Metadata provided by EXIF.tools