Fine Offset Electronics WH2F Weather Station User Manual WH117L

Fine Offset Electronics Co., Ltd. Weather Station WH117L

User Manual

Weather Station User Manual

Table of Contents

1Introduction ..................................................................................................................................... 2

2Product Features .............................................................................................................................. 2

3Getting Started ................................................................................................................................ 3

2.1 Parts List ....................................................................................................................................... 3

2.2 Recommend Tools ......................................................................................................................... 3

2.3 Thermo-Hygrometer Sensor Set Up .............................................................................................. 3

2.4 Display Console Set Up ................................................................................................................ 4

2.4.1 Radio Controlled Clock (RCC) .............................................................................................. 5

2.4.2Display Console Layout ..................................................................................................... 5

2.4.3Sensor Operation Verification ............................................................................................ 6

4Remote Sensor Installation ............................................................................................................. 6

3.1Sensor Placement ................................................................................................................... 6

3.2Wireless Reception Considerations ........................................................................................ 7

5Console Operation ........................................................................................................................... 7

4.1Quick Display Mode .............................................................................................................. 7

4.1.1 Quick Display Mode Quick Reference Guide ........................................................................ 7

4.1.2Quick Display Mode Operation ......................................................................................... 7

4.2Set (Program) Mode ............................................................................................................... 8

4.2.1Set Mode Quick Reference Guide ...................................................................................... 8

4.2.2Set Mode Operation ........................................................................................................... 8

4.2.3 Setting Barometric Pressure ................................................................................................. 10

4.2.4Setting Calibrated Humidity............................................................................................. 11

4.2.5Setting Calibrated Temperature ........................................................................................ 11

4.3Alarm Mode ......................................................................................................................... 12

4.3.1 Alarm Display ...................................................................................................................... 12

4.3.2Alarm Programming ......................................................................................................... 12

4.3.3Cancelling the Alarm ........................................................................................................ 13

4.3.4Outdoor Alarm – Temperature vs. Dew Point .................................................................. 13

4.4 Min/Max Mode ........................................................................................................................... 13

4.5Other Console Features ........................................................................................................ 14

4.5.1Weather Forecasting ......................................................................................................... 14

4.5.2Weather Forecast Initialization ......................................................................................... 14

4.5.3Weather Icons ................................................................................................................... 15

4.5.4Weather tendency indicator .............................................................................................. 15

4.5.5Storm threshold indicator ................................................................................................. 16

4.5.6Pressure threshold setting ................................................................................................. 16

4.5.7Pressure Graph ................................................................................................................. 16

4.5.8Restoring Lost Outdoor Temperature and Humidity Sensor ............................................ 16

5Glossary of Terms ......................................................................................................................... 16

6Specifications ................................................................................................................................ 17

6.1 Wireless Specifications ............................................................................................................... 17

6.2 Measurement Specifications ....................................................................................................... 17

6.3 Power Consumption .................................................................................................................... 17

7Troubleshooting Guide .................................................................................................................. 17

8Accessories ................................................................................................................................... 19

9Product Revisions ......................................................................................................................... 19

10Liability Disclaimer .................................................................................................................. 19

11FCC Statement .......................................................................................................................... 20



1 Introduction

Thank you for your purchase of the Weather Station WH117L with Temperature&Humidity, sensor

WH2F. The following user guide provides step by step instructions for installation, operation and

troubleshooting.

Product Features

Figure 1

No Description No Description

1 Radio Controlled Clock with Perpetual

Calendar 4 Forecast Icons

2 Indoor Humidity and Temperature 5 Barometric Pressure

3 Outdoor Humidity and Temperature 6 Barograph

Figure 2

2 GettingStarted

Note: The power up sequence must be performed in the order shown in this section (remote

transmitter first, Display Console second) to avoid the console synchronization time out.

The WH117L weather station consists of a display console (receiver), and a thermo-hygrometer

(remote transmitter).

2.1PartsList

QTY Item

1 Display Console

Frame Dimensions (LxWxH): 7.25 x 4 x 1.25 in

LCD Dimensions (LxW): 4.25 x 2.50”

1 Thermo-hygrometer transmitter (WH2F) with mounting bracket

Dimensions (LxWxH): 3.5” x 2.5” x 0.9”

2.2RecommendTools

 Philips precision screwdriver

 Drill for mounting bracket

2.3Thermo‐HygrometerSensorSetUp

Note: To avoid permanent damage, please take note of the battery polarity before inserting the

batteries.

Remove the battery door on the back of the sensor with a Philips screwdriver (there is only one screw,

at the bottom of the unit). Insert two AAA batteries as shown in Figure 3.

We recommend lithium batteries for cold weather climates, but alkaline batteries are sufficient for

most climates. We do not recommend rechargeable batteries. They have lower voltages, do not operate

well at wide temperature ranges, and do not last as long, resulting in poorer reception.

Replace the battery door and set screw. Note that the temperature and humidity will be displayed on

the LCD display. Looking at the back of the unit from left to right, the polarity is (-) (+) for the top

battery and (+) (-) for the bottom battery.

Figure 3

2.4DisplayConsoleSetUp

Note: To avoid permanent damage, please take note of the battery polarity before inserting the

batteries.

Place the remote thermo-hygrometer about 5 to 10’ away from the display console (if the sensor is too

close, it may not be received by the display console).

Remove the battery door on the back of the display. Insert three AA (alkaline or lithium, avoid

rechargeable) batteries in the back of the display console. Looking at the back of the unit (left to right),

the polarity is (+) (-) for the top battery, (-) (+) for the middle battery and (+) (-) for the bottom battery.

The display will beep once and all of the LCD segments will light up for a few seconds to verify all

segments are operating properly.

Replace the battery door, and fold out the desk stand and place the console in the upright position.

The console will instantly display indoor temperature, humidity, barometer, tendency, date and time.

The remote search icon will turn on and should remain on for several minutes:

The outdoor temperature and humidity will update on the display within a few minutes.

Do not touch any buttons until the remote sensor reports in, otherwise the remote sensor search

mode will be terminated and the search icon will turn off. When the remote sensor data has been

received, the console will automatically switch to the normal mode, and all further settings can be

performed.

If the remote does not update, please reference the troubleshooting guide in Section 7.

2.4.1RadioControlledClock(RCC)

If your console is equipped with the Radio Controlled Clock (RCC), the icon WWVB will appear

above the time. WWVB is the NIST time signal radio station near Fort Collins, Colorado.

The RCC is received by the wireless transmitter, and passed to the console. After the remote sensor is

powered up, the sensor will transmit weather data for 30 seconds, and then the sensor will begin radio

controlled clock (RCC) reception. The sensor search icon will remain on:

During the RCC time reception period (maximum 10 minutes), no weather data will be transmitted to

avoid interference.

If the signal reception is not successful (normally during the day due to solar interference), the sensor

search will be cancelled, the outdoor temperature and humidity will update as normal, and the RCC

search will automatically resume every two hours until the signal is successfully captured. The regular

RF link will resume once RCC reception routine is finished. In some locations, RCC reception may

take a couple of days to receive the signal. The temperature and humidity data will continue to

transmit during this period.

Once the radio controlled time is RCC reception icon will turn on (reference Figure 4).

2.4.2 DisplayConsoleLayout

Note: The following illustration shows the full segments of the LCD for description purposes

only and will not appear like this during normal operation.

Figure 2

1. DST (daylight savings time)

2. WWVB Radio Controlled Time

3. Time

4. Radio Controlled Clock reception

icon

5. Alarm ON indicator

6. Day of week/ time zone

7. Date

8. Indoor humidity display

9. Indoor temperature and humidity low

alarm and high alarm

10. Indoor temperature display

11. Temperature display units

12. Indoor temperature and humidity

alarm on indicator

13. Remote sensor transmit signal

indicator

14. MIN/MAX information

15. Dew

oint tem

erature dis

16. Outdoor humidity display

17. Outdoor temperature and humidity

low alarm and high alarm

18. Temperature display units

19. Outdoor temperature display

20. General outdoor alarm icon

21. Weather forecast icon

22. Weather tendency indicator

23. Pressure with 24 hour history graph

24. Pressure high alarm

25. Pressure low alarm

26. Absolute or relative air pressure

selection

27. Barometer air pressure

28. Pressure display unit (inHg or hPa)

29. Pressure alarm ON indicator

NOTE: The snooze key is on the top of

the display console

2.4.3 SensorOperationVerification

Verify the indoor and outdoor humidity match closely with the console and sensor array in the same

location (about 10’ apart). The sensors should be within 10% (the accuracy is ± 5%). Allow about 30

minutes for both sensors to stabilize.

Verify the indoor and outdoor temperature match closely with the console and sensor array in the same

location (about 10’ apart). The sensors should be within 4°F (the accuracy is ± 2°F). Allow about 30

minutes for both sensors to stabilize.

3 RemoteSensorInstallation

3.1 SensorPlacement

It is recommended you mount the remote sensor outside on a north facing wall, in a shaded area, at a

height at or above the receiver. If a north facing wall is not possible, choose a shaded area, under an

eve.

Direct sunlight and radiant heat sources will result in inaccurate temperature readings. Although the

sensor is weatherproof, it is best to mount in a well-protected area, such as an eve.

Use 3 screws (included) to affix the mounting bracket to the wall with a precision screwdriver.

Connect the remote sensor to the wall bracket. It is recommended to drill pilot holes first.

Figure 4

Note: Make sure the sensor is mounted vertically and not lying down on a flat surface. This will

insure optimum reception.

3.2 WirelessReceptionConsiderations

Wireless signals are impacted by distance, interference (other weather stations, wireless phones,

wireless routers, TVs and computer monitors), and transmission barriers, such as walls. In general,

wireless signals will not penetrate solid metal and earth (down a hill, for example).

The following is a table of reception loss vs. the transmission medium. Each “wall” or obstruction

decreases the transmission range by the factor shown below.

Medium RF Signal Strength Reduction

Glass (untreated) 5-15%

Plastics 10-15%

Wood 10-40%

Brick 10-40%

Concrete 40-80%

Metal 90-100%

4 ConsoleOperation

Note: The console has four keys for easy operation: SET key, ALARM key, MIN/MAX key and

+ key. There are four program modes: Quick Display Mode, Set Mode, Alarm Mode and Min/Max

Mode.

Any program mode can be exited at any time by either pressing the SNOOZE/LIGHT key (on the top

of the display console), or waiting for the 10-second time-out to take effect.

4.1 QuickDisplayMode

4.1.1QuickDisplayModeQuickReferenceGuide

Command Mode Settings

[SET] EnterQuickSetMode,Outdoor

Temperat urevsDewPoint

Press[+]totogglebetweenoutdoor

temperatureanddewpoint.

[SET] RelativePressurevsAbsolute

Pressure

Press[+]totogglebetweenrelativepressureand

absolutepressure.

4.1.2 QuickDisplayModeOperation

While in Normal Mode, press the SET key to enter the Quick Display Mode as follows (once for

outdoor temperature and dew point and twice for absolute pressure and relative pressure):

1. Display Outdoor Temperature and Dew Point. Press the MIN/MAX or + key to toggle

between outdoor temperature and dew point.

2. Absolute Pressure and Relative Pressure. Press the MIN/MAX or + key to toggle between

absolute pressure and relative pressure.

4.2 Set(Program)Mode

4.2.1 SetModeQuickReferenceGuide

Command Mode Settings

[SET]+3

seconds

EnterSetMode,DaylightSavings

Time(DST)

Press[+]totoggleOFFandON

[SET] TimeZone(TZ)Press[+]toincrease.[MIN/MAX]todecrease

[SET]12/24HourFormatPress[+]totogglebetween12hour(12h)and

24hour(24h)format

[SET]HourofDayPress[+]toincrease.[MIN/MAX]todecrease

[SET]MinuteofDayPress[+]toincrease.[MIN/MAX]todecrease

[SET]Year Press[+]toincrease.[MIN/MAX]todecrease

[SET]MonthofYearPress[+]toincrease.[MIN/MAX]todecrease

[SET]DayofMonthPress[+]toincrease.[MIN/MAX]todecrease

[SET]Tempe ratureUnitsofMeasure Press[+]totogglebetweendegFanddegC

[SET]IndoorTemperature Calibration Press[+]toincrease.[MIN/MAX]todecrease

[SET]IndoorHumidityCalibration Press[+]toincrease.[MIN/MAX]todecrease

[SET]OutdoorTemperat ureCalibration Press[+]toincrease.[MIN/MAX]todecrease

[SET]OutdoorHumidityCalibration Press[+]toincrease.[MIN/MAX]todecrease

[SET]BarometricPressureUnitsof

Measure

Press[+]totogglebetweeninHgandhPa

[SET]RelativePressureCalibration Press[+]toincrease.[MIN/MAX]todecrease

[SET]PressureThresholdforForecast Press[+]toincrease.[MIN/MAX]todecrease

[SET]StormThresholdforForecast Press[+]toincrease.[MIN/MAX]todecrease

[SET]ExitSetMode

4.2.2 SetModeOperation

While in Normal Mode, press and hold the SET key for at least three seconds to enter the Set Mode.

The first setting will begin flashing. You can press the SET key again to skip any step, as defined

below.

Note: In the Set mode, press the + key or MIN/MAX key to change or scroll the value. Hold

the + key or MIN/MAX key for 3 seconds to increase/decrease rapidly.

Note: Press the SNOOZE key (or wait 30 seconds for the programming mode to timeout), and

the Set Mode will return to Normal Mode.

1. Daylight Savings Time (DST). The DST (ON or OFF) setting will begin flashing. Press the

+ key to toggle between DST ON and DST OFF.

2. Time Zone Settings. Press the SET key again to adjust the Time Zone (TZ) setting.

Press the + key or MIN/MAX key to adjust the time zone from -12 to 12, based on the

number of hours from Coordinated Universal Time, or Greenwich Mean Time (GMT).

The following table provides times zones throughout the world. Locations in the eastern

hemisphere are positive, and locations in the western hemisphere are negative.

Hours from

GMT Time Zone Cities

-12 IDLW: International Date Line West ---

-11 NT: Nome Nome, AK

-10 AHST: Alaska-Hawaii Standard

CAT: Central Alaska

HST: Hawaii Standard

Honolulu, HI

-9 YST: Yukon Standard Yukon Territory

-8 PST: Pacific Standard Los Angeles, CA, USA

-7 MST: Mountain Standard Denver, CO, USA

-6 CST: Central Standard Chicago, IL, USA

-5 EST: Eastern Standard New York, NY, USA

-4 AST: Atlantic Standard Caracas

-3 --- São Paulo, Brazil

-2 AT: Azores Azores, Cape Verde Islands

-1 WAT: West Africa ---

0 GMT: Greenwich Mean

WET: Western European London, England

1 CET: Central European Paris, France

2 EET: Eastern European Athens, Greece

3 BT: Baghdad Moscow, Russia

4 --- Abu Dhabi, UAE

5 --- Tashkent

6 --- Astana

7 --- Bangkok

8 CCT: China Coast Bejing

9 JST: Japan Standard Tokyo

10 GST: Guam Standard Sydney

11 --- Magadan

12 IDLE: International Date Line East

NZST: New Zealand Standard Wellington, New Zealand

3. 12/24 Hour Format. Press the SET key again to adjust the 12/24 hour format setting. Press

the + key to change between 12 hour and 24 hour format.

4. Change Hour. Press the SET key again to set the hour. Press the + key or MIN/MAX key to

adjust the hour up or down.

5. Change Minute. Press the SET key again to set the minute. Press the + key or MIN/MAX

key to adjust the minute.

6. Change Year. Press the SET key again to set the calendar year. Press the + key or

MIN/MAX key to adjust the calendar year.

7. Change Month. Press the SET key again to set the calendar month. Press the + key or

MIN/MAX key to adjust the calendar month.

8. Change Day. Press the SET key again to set the calendar day. Press the + key or MIN/MAX

key to adjust the calendar day.

9. Temperature Units (Celsius or Fahrenheit). Press the + key again to toggle the temperature

units from Celsius to Fahrenheit.

10. Indoor Temperature Calibration (default is measured indoor temperature). Press the SET

key to adjust the indoor temperature. Press the + key or MIN/MAX key to adjust the

temperature up or down in 0.1 degC (0.18 degF) increments.

To view the uncalibrated value, press the ALARM key while the temperature is flashing.

Reference Section 4.2.5 Setting Calibrated Temperature for more details on this function.

11. Indoor Humidity Calibration (default is measured indoor humidity). Press the SET key to

adjust the indoor humidity. Press the + key or MIN/MAX key to adjust the relative humidity

up or down in 1% increments.

To view the uncalibrated value, press the ALARM key while the humidity is flashing.

Reference 4.2.4 Setting Calibrated Humidity for more details on this function.

12. Outdoor Temperature Calibration (default is measured outdoor temperature). Press the

SET key to adjust the outdoor temperature. Press the + key or MIN/MAX key to adjust the

temperature up or down in 0.1 degC (0.18 degF) increments.

To view the uncalibrated value, press the ALARM key while the temperature is flashing.

Reference Section 4.2.5 Setting Calibrated Temperature for more details on this feature.

13. Outdoor Humidity Calibration (default is measured outdoor humidity). Press the SET key

to adjust the outdoor humidity. Press the + key or MIN/MAX key to adjust the relative

humidity up or down in 1% increments.

To view the uncalibrated value, press the ALARM key while the humidity is flashing.

Reference 4.2.4 Setting Calibrated Humidity for more details on this function.

14. Barometric Pressure Display Units (hPa or inHg). Press the SET key again to toggle the

pressure units between hPa or inHg.

15. Relative Pressure Calibration (default is 29.92 inHg). Press the SET key to adjust the

relative barometric pressure. Press the + key or MIN/MAX key to adjust the relative

barometric pressure up or down. Reference Section 4.5.6 for more details on this function.

16. Pressure Threshold Setting (default level 2). Press the SET key again to adjust the

pressure threshold setting. Press the + key or MIN/MAX key to adjust the pressure

threshold up or down. Reference Section 4.5.4 for more details on this function.

17. Storm Threshold Setting (default level 4). Press the SET key again to adjust the storm

threshold setting. Press the + key or MIN/MAX key to adjust the storm threshold up or

down. Reference Section 4.5.5 for more details on this function.

4.2.3SettingBarometricPressure

Note: This is a continuation of the previous section. To enter this mode, you must start at the

beginning of this section.

The display console displays two different pressures: absolute (measured) and relative (corrected to

sea-level).

To compare pressure conditions from one location to another, meteorologists correct pressure to

sea-level conditions. Because the air pressure decreases as you rise in altitude, the sea-level corrected

pressure (the pressure your location would be at if located at sea-level) is generally higher than your

measured pressure.

Thus, your absolute pressure may read 28.62 inHg (969 mb) at an altitude of 1000 feet (305 m), but

the relative pressure is 30.00 inHg (1016 mb).

The standard sea-level pressure is 29.92 in Hg (1013 mb). This is the average sea-level pressure

around the world. Relative pressure measurements greater than 29.92 inHg (1013 mb) are

considered high pressure and relative pressure measurements less than 29.92 inHg are considered low

pressure.

To determine the relative pressure for your location, locate an official reporting station near you (the

internet is the best source for real time barometer conditions, such as Weather.com or

Wunderground.com), and set your weather station to match the official reporting station.

To change the relative pressure in the SET mode, press the + key or MIN/MAX key to increase or

decrease the relative pressure setting to match the official reporting station.

4.2.4 SettingCalibratedHumidity

Note: This is a continuation of the previous section. To enter this mode, you must start at the

beginning of this section.

The display console allows you to calibrate both the indoor and outdoor humidity. Humidity is a

difficult parameter to measure accurately and drifts over time. The calibration feature allows you to

zero out this error. To calibrate humidity, you will need an accurate source, such as a sling

psychrometer or Humidipaks One Step Calibration kit.

To calibrate indoor humidity, in the Set Mode with indoor humidity flashing, press the + key or

MIN/MAX key to increase or decrease the humidity setting (in increments of 1%) to match the

calibrated or known humidity source. To return the indoor humidity to the measured value, press and

hold the SET key for 3 seconds and the humidity will return to the uncalibrated value.

Note: The remote (outdoor) thermo-hygrometer will always display the measured humidity level

and not the calibrated humidity level. Only the console will show the calibrated value.

Note: The dew point calculation is based on the calibrated humidity level.

4.2.5 SettingCalibratedTemperature

Temperature is measured by a resistive thermal device (RTD) and is subject to electronic variation.

Temperature errors can also occur when a sensor is placed too close to a heat source (such as a

building structure, the ground or trees).

To calibrate the indoor or outdoor temperature, we recommend a mercury or red spirit (fluid)

thermometer. Bi-metal (dial) and other digital thermometers are not a good source and have their own

margin of error. Using a local weather station in your area is also a poor source due to changes in

location, timing (airport weather stations are only updated once per hour) and possible calibration

errors (many official weather stations are not properly installed and calibrated).

Place the sensor in a shaded, controlled environment next to the fluid thermometer, and allow the

sensor to stabilize for 24 hours. Compare this temperature to the fluid thermometer and adjust the

console to match the fluid thermometer.

To calibrate indoor or outdoor temperature, in the Set Mode with indoor or outdoor temperature

flashing, press the + key or MIN/MAX key to increase or decrease the temperature setting (in

increments of 0.1 degC or 0.18 degF) to match the calibrated or known temperature source.

Note: The remote (outdoor) thermo-hygrometer will always display the measured temperature

level and not the calibrated temperature level. Only the console will show the calibrated value.

Note: The dew point calculation is based on the calibrated temperature level.

4.3 AlarmMode

4.3.1AlarmDisplay

While in Normal Mode, press the ALARM key to enter the High Alarm Mode. Press the ALARM

key again to enter the Low Alarm Mode. Press the ALARM key again to return to normal mode (or

wait 30 seconds for the programming mode to timeout).

Note: After entering the ALARM mode, the console will display the high and low alarm

settings. If the value reads --.-- (dashes), the alarm is not active.

4.3.2 AlarmProgramming

While in Alarm Mode, press the SET key to set the alarms. The following are high and low alarms:

High Alarm Limits:

 Time alarm (hour/minute)

 Indoor humidity high alarm

 Indoor temperature high alarm

 Outdoor humidity high alarm

 Outdoor temperature / dew point high alarm

 Pressure high alarm

Low Alarm Limits:

 In the Low Alarm Mode press the SET key to select the following alarm modes:

 Time alarm (hour/minute)

 Indoor humidity low alarm

 Indoor temperature low alarm

 Outdoor humidity low alarm

 Outdoor temperature / dew point low alarm

 Pressure low alarm

In the alarm mode, Press the + key or MIN/MAX key to change or scroll the alarm value.

Hold the + key or MIN/MAX key for 3 seconds to change the number rapidly. Press the ALARM key

to select the alarm on or off (if alarm is enabled, the speaker icon on the LCD will be turned on

indicating the alarm function has been enabled).

Press the SET key to confirm the setting and continue pressing the SET key to toggle through each

alarm mode until it returns to the normal display mode.

Press the SNOOZE key or wait 30 seconds for the programming mode to timeout, and the alarm

mode will return to the normal mode.

4.3.3 CancellingtheAlarm

When an alarm condition has been activated, the specific alarm will sound and flash for 120 seconds.

Press any key to cancel the alarm.

When an alarm condition is activated again within 10 minutes, the alarm will not sound but will

continue to flash until the weather condition is stable. This feature is useful to avoid repeated

triggering for the same alarm value.

The alarm will reset automatically once the value has fallen below the set value, or if a new value is

entered.

4.3.4 OutdoorAlarm–Temperaturevs.DewPoint

When the outdoor weather alarm has been triggered, it will flash on the LCD display and the general

outdoor alarm icon and high/low alarm icon will flash. For example, in the outdoor temperature

display mode, when dew point high alarm is triggered the DEW POINT icon will flash along with

general outdoor alarm icon and high alarm icon, indicating that the current alarm source is from dew

point.

Figure 4

4.4Min/MaxMode

Note: The min and max settings cannot be reset at the same time. They must be reset on an

individual basis.

While in Normal Mode, press the MIN/MAX key to enter the maximum mode, and the MAX icon

and maximum records will be displayed and begin flashing.

Press MIN/MAX key again to enter the minimum mode, and the MIN icon and minimum records will

be displayed and begin flashing.

Press MIN/MAX key again to return the Normal Mode.

In the maximum (or minimum) reading Mode, press the + key to display the specific maximum (or

minimum) value you wish to reset. This value will begin flashing with the time and date time stamp at

which the maximum (or minimum) value occurred. Select the + key again to proceed to the next

parameter, in the following order:

1. Indoor humidity maximum (or minimum)

2. Indoor temperature maximum (or minimum)

3. Outdoor humidity maximum (or minimum)

4. Outdoor temperature maximum (or minimum)

5. Pressure maximum (or minimum)

Press the SET key for two seconds to reset the specific value (that is flashing) and associated date and

time to the current reading.

Press the SNOOZE key or wait 30 seconds for the programming mode to timeout, and the Min/Max

mode will return to Normal Mode.

4.5 OtherConsoleFeatures

The following section describes additional console features.

4.5.1 WeatherForecasting

Note: The weather forecast or pressure tendency is based on the rate of change of barometric

pressure. In general, when the pressure increases, the weather improves (sunny to partly cloudy) and

when the pressure decreases, the weather degrades (cloudy to rain).

It may take several days to begin forecasting the weather. In the meantime, there may be no trend

arrows and the both icons display partly cloudy.

The weather forecast is an estimation or generalization of weather changes in the next 24 to 48 hours,

and varies from location to location. The tendency is simply a tool for projecting weather conditions

and is never to be relied upon as an accurate method to predict the weather.

4.5.2 WeatherForecastInitialization

When the console is powered up, the forecast prediction is in the “learning mode”. Two partly cloudy

icons will be displayed, as shown below. When there is a change in barometric pressure over 24 to 72

hours, the forecast icons will exit the learning mode.

4.5.3 WeatherIcons

Sunn

Partl

Cloud

Rain

The four weather icons are Sunny, Partly Cloudy, Cloudy and Rainy. There are also two weather

tendency indicators to show the air pressure tendency between the weather icons.

4.5.4 Weathertendencyindicator

The weather tendency arrow is located between the weather icons to show the air pressure tendency

and provide a forecast based on increasing or decreasing air pressure.

The arrow pointing to the right indicates that the air pressure is increasing and the weather is expected

to improve. The arrow pointing the left indicates that the air pressure is decreasing and the weather is

expected to deteriorate.

The weather tendency is based on the pressure change since last six hours. If the weather is changing,

the weather tendency indicator (animated arrows) will flash for three hours, indicating the weather is

expected to change. If the weather conditions become stable and no new weather change conditions

are met, then the arrows will be fixed.

Example 1: Pressure is decreasing, weather is deteriorating in 24-48 hours.

Example 2: Pressure is increasing, weather is improving in 24-48 hours.

4.5.5 Stormthresholdindicator

The storm threshold (the negative rate of pressure change signifying a storm is expected) can be

adjusted by the user from level 3 to level 9 (the default level 4 mbar/hour).

When negative rate of change of pressure is exceeded for 3 hours, the storm warning indicator will be

activated, and the clouds with rain icon and tendency arrows will flash for 3 hours indicating the storm

warning feature has been activated.

4.5.6 Pressurethresholdsetting

The pressure threshold (the negative or positive rate of change of pressure signifying a change in the

weather) can be adjusted by the user from level 2 to level 4 (default level 2 mbar/hour).

The lower the level pressure threshold setting, the higher sensitivity for weather forecast changes.

Locations that experience frequent changes in air pressure require a higher setting compared to

locations where the air pressure is typically stagnant.

4.5.7 PressureGraph

The pressure graph displays the barometric pressure for the last 24 hours. Each bar represents three

hours. The vertical scale of the graph is auto-scaled. There is not fixed pressure level for each bar, and

is intended for visualizing trends only.

4.5.8 RestoringLostOutdoorTemperatureandHumiditySensor

If the signal is lost between the remote sensor (or transmitter) and the display console (or the receiver),

to resynchronize, while in normal mode, press and hold the + key for 10 seconds. The transmitter

search icon will appear:

Please wait several minutes for the search icon to turn off and the remote sensor reports in. Do not

touch any buttons until synchronization is complete.

If the synchronization fails, reset the console by removing one battery from the display console, wait

10 seconds, and reinsert the battery, as specified in Section 2.4 Display Console Set Up.

5 GlossaryofTerms

Term Definition

Absolute Barometric

Pressure Relative barometric pressure, corrected to sea-level. To compare

pressure conditions from one location to another, meteorologists correct

pressure to sea-level conditions. Because the air pressure decreases as

you rise in altitude, the sea-level corrected pressure (the pressure your

location would be at if located at sea-level) is generally higher than your

measured pressure.

Accuracy Accuracy is defined as the ability of a measurement to match the actual

value of the quantity being measured.

HectoPascals (hPa) Pressure units in SI (international system) units of measurement. Same

as millibars (1 hPa = 1 mbar)

Hygrometer A hygrometer is a device that measures relative humidity. Relative

humidity is a term used to describe the amount or percentage of water

vapor that exists in air.

Inches of Mercury (inHg) Pressure in Imperial units of measure.

1 inch of mercury = 33.86 millibars

Range Range is defined as the amount or extent a value can be measured.

Relative Barometric

Pressure Measured barometric pressure relative to your location or ambient

conditions.

6 Specifications

6.1WirelessSpecifications

 Line of sight wireless transmission (in open air): 300 feet

 Frequency: 433.92 MHz

 Update Rate: 48 seconds

6.2MeasurementSpecifications

The following table provides specifications for the measured parameters.

Measurement Range Accuracy Resolution

Indoor Temperature 32 to 140 °F ± 2 °F 0.1 °F

Outdoor Temperature -40 to 149 °F ± 2 °F 0.1 °F

Indoor Humidity 1 to 99 % ± 5% (only guaranteed

between 20 to 90%) 1 %

Outdoor Humidity 1 to 99% ± 5% (only guaranteed

between 20 to 90%) 1 %

Barometric Pressure 8.85 to 32.50 inHg ± 0.08 inHg (within

range of 27.13 to 32.50

inHg)

0.01 inHg

6.3PowerConsumption

 Base station : 3 x AA 1.5V Alkaline batteries

 Remote sensor : 2 x AAA 1.5V Alkaline batteries

 Battery life: Minimum 12 months for base station

Minimum 24 months for thermometer-hygrometer sensor (use lithium batteries in cold

weather climates)

7 TroubleshootingGuide

Problem Solution

Wireless remote (thermo-hygrometer) not

reporting in to console.

1. Resync the unit. Press and hold the + key for

10 seconds to resynchronize. The remote sensor

search icon

There are dashes (--) on the display

console.

will turn on. Wait several minutes for the remote

sensor to report in, or the search icon to turn off.

If the synchronization fails, reset the console by

removing one battery from the display console,

wait 10 seconds, and reinsert the battery.

Do not press any buttons while in the search

mode.

2. Check the remote sensor is powered up and

displaying the temperature and humidity on the

LCD display.

3. Install a fresh set of batteries in the remote

thermo-hygrometer. For cold weather

environments, install lithium batteries.

4. The maximum line of sight communication

range is 300’. Move the sensor assembly closer

to the display console.

5. If the sensor assembly is too close (less than

5-10’), move the sensor assembly away from the

display console.

6. Make sure the remote sensors are not

transmitting through solid metal (acts as an RF

shield), or earth barrier (down a hill).

7. Move the display console around electrical noise

generating devices, such as computers, TVs and

other wireless transmitters or receivers.

8. Move the remote sensor to a higher location.

Move the remote sensor to a closer location.

9. Radio Frequency (RF) Sensors cannot transmit

through metal barriers (example, aluminum

siding) or multiple, thick walls.

Temperature sensor reads too high in the

day time. Make sure the thermo-hygrometer is mounted in a

shaded area on the north facing wall.

Indoor and Outdoor Temperature do not

agree 1. Allow up to one hour for the sensors to stabilize

due to signal filtering. The indoor and outdoor

temperature sensors should agree within 4 °F

(the sensor accuracy is ± 2 °F).

2. Perform a temperature calibration (reference

Section 4.2.5)

Indoor and Outdoor Humidity do not

agree 1. Allow up to one hour for the sensors to stabilize

due to signal filtering. The indoor and outdoor

humidity sensors should agree within 10 % (the

sensor accuracy is ± 5 %)

2. Perform a humidity calibration (reference

Section 4.2.4)

Console outdoor humidity and remote

humidity do not agree. The console displays the calibrated humidity. The remote

displays the measured humidity only. Refer to 4.2.4 to

set and reset the humidity calibration.

Relative pressure does not agree with

official reporting station 1. You may be viewing the relative pressure, not

the absolute pressure.

2. Make sure you properly calibrate the barometer

to an official local weather station (reference

Section 4.2.1)

3. The barometer is only accurate to ± 0.08 inHg

within the following relative pressure range:

27.13 to 32.50 inHg, which corresponds to an

altitude of -2,200 to 2,700 feet. At higher

altitudes, expect some non-linearity or error.

The forecast icon is not accurate The weather station console must run for several days to

trend barometric pressure.

The weather forecast is an estimation or generalization of

weather changes in the next 24 to 48 hours, and varies

from location to location. The tendency is simply a tool

for projecting weather conditions and is never to be

relied upon as an accurate method to predict the weather.

Display console contrast is weak Replace console batteries with a fresh set of batteries.

Console beeps and resets Replace console batteries with a fresh set of batteries.

8 Accessories

Accessory Description

Energizer AA Lithium Battery (2-pack) -

Batteries for Long Life and Cold Climates AA lithium batteries for cold weather climates.

Ambient Weather SRS100LX

Temperature and Humidity Solar

Radiation Shield

Solar Radiation Shield improves temperature accuracy

for hot weather climates. Remove the rain guard and

install over thermo-hygrometer.

9 ProductRevisions

Revision Description

WS-1170 Initial Release

WS-1171



Added humidity calibration

WS-1171A



Added temperature calibration

 Increased programming timeout from 10

seconds to 30 seconds

 Changed barograph from scrolling to

non-scrolling.

 Added function to reacquire lost remote

signal without powering down and up

console.

WH117L



Moved RCC receiver from the console to

the transmitter to improve RCC

reception.

10 LiabilityDisclaimer

Please help in the preservation of the environment and return used batteries to an authorized depot.

The electrical and electronic wastes contain hazardous substances. Disposal of electronic waste in

wild country and/or in unauthorized grounds strongly damages the environment.

Reading the “User manual” is highly recommended. The manufacturer and supplier cannot accept any

responsibility for any incorrect readings and any consequences that occur should an inaccurate reading

take place.

This product is designed for use in the home only as indication of weather conditions. This product is

not to be used for medical purposes or for public information.

The specifications of this product may change without prior notice.

This product is not a toy. Keep out of the reach of children.

No part of this manual may be reproduced without written authorization of the manufacturer.

FCC Statement

Statement according to FCC part 15.19:

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause

undesired operation.

Statement according to FCC part 15.21:

Modifications not expressly approved by this company could void the user's authority to operate the

equipment.

Statement according to FCC part 15.105:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Fine Offset Electronics WH2F Weather Station User Manual WH117L

Fine Offset Electronics Co., Ltd. Weather Station WH117L

User Manual

Navigation menu

Namespaces

Views

Navigation