Fingerchip Intelligent Technology E202 Smart lock User Manual 1

Download:
Mirror Download [FCC.gov]
Document ID	4023063
Application ID	APWAtGxe4ii2HnJzwmUPMQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	66.86kB (835765 bits)
Date Submitted	2018-09-28 00:00:00
Date Available	2018-09-28 00:00:00
Creation Date	2018-08-29 17:02:19
Producing Software	Corel PDF Engine Version 16.1.0.843
Document Lastmod	2018-08-29 17:02:19
Document Title	未命名 -1
Document Creator	CorelDRAW X6
Document Author:	Administrator

Information & Safety Warnings
Note: Please prepare a Phillips screw driver and 4 AA batteries before
Smart Lock User Manual
2. Installation Overview
10 9 8 7 6
11 12 13
14
4 3
2 1
installation.
1. Keep your fingers clean before using this product.
2. In original settings, it can be unlocked with any fingerprint, any card,
or password `1234567890` and `#`.
3. If the power is insufficient, there will be an alarm prompt, please
replace with 4 new batteries in time.
4. Please don`t use corrodent material to clean the surface.
5. When the password/fingerprint/card/APP can not unlock the door,
please use the key to unlock the door. Please keep the emergency key
with you or put it in outdoor safe place.
6. The lock is suitable for 40-100mm thick doors.
Features
1. The total capacity of system is 300, and Fingerprint capacity is up to 100,
and the first three are administrator.
2. Touching button, durable.
3. Support 6-8 password and 20 virtual password.
15 16
3 . Confirm The Direction of The Door
This smart lock is suitable for Left Out/Left In/Right Out/Right In) 4 kinds of door
opening directions.
Left Hand Door
Indoor
4. Support low power warning.
Name
Outdoor
Indoor
Fingerprint Sensor
semiconductor
500
Identify Time
0.3S
Unlock Way
Fingerprint, Card, Password, Key and APP
System Capacity
300
Right Hand Door
Indoor
Right In
Left In
Parameter
DPI
17 18 19 20
1.Front Panel
2.Connection Column
3.Square Steel
4.Lock Body
5.Connection Line
6.Back Panel
7.`SET` Button
8.Connectiion Column Screws
9.Battery Cover
10.Battery Cover Screw
11.Back Handle
12.Connectiion Column Screws
13.Reverse Lock Knob
14.Back Locking Paddle
15.Latch-bolt
16.Lock Body Screws
17.Connectiion Column
18.Key Hole
19.Emergency Power Port
20.Front Handle
Outdoor
Indoor
Right Out
Left Out
Outdoor
Outdoor
4. Open Hole
Please refer to the opening hole drawing, and drill right holes on the door.
Supply Voltage
6V
Low Voltage Warning
4.8V
5. Install Lock Body
Standby Current
<=50uA
5.1. Choose the installation direction of the latch-bolt of the lock body by
the door opening directions.
Installation
Left In/
Right Out
1. Installation Instructions
Left Out/
Right In
a. It is recommended to look for professionals to install, watch the video
carefully before installing.
b. Please note that the connection line can’t be pressed or folded during
installation.
c. Before the installation, the lock must be selected correctly according
E202
Please read this manual carefully before use
Customer Service: （+86）+400 900 5952
http://en.fingercrystal.com
to the door opening direction, because the handle can't be adjusted.
d. While installing, the door must be in half open state until the
commissioning is completed.
e. After the installation is completed, when the fingerprint, card,
password(1234567890) and #, APP, key unlock, test whether the front
handle and back handle unlock/lock normally or not.
f . If it does not work properly, please check if there is improper installation
or the power cord is loose.
5.2. Change the direction of lock body
latch-bolt
a. Push the reversing block to the other
side.
b. Push the latch-bolt into the lock and
turn 180 degrees.
Reversing block
Square Steel
Hole
c. Put back the reversing block, and the
latch-bolt will pop up automatically.
Lock Body(5052)
5.3. Put the lock body into the door frame and tighten 2 fixing screws.
Using The Lock
6. Choose The Parts
Add The Administrator
Choose suitable parts according to the following table.
Connection Column Connection Column
Length
Screw Length
Door thickness
Square Steel
Length
1.57-2.16 Inch
3.15 Inch
1.38 Inch
2.17-2.36 Inch
3.15 Inch
1.77 or 2.17 Inch
1.18 and 1.97 Inch
2.76-3.15 Inch
3.94 Inch
1.77 or 2.17 Inch
1.97 and 2.76 Inch
3.55-3.94 Inch
4.72 Inch
1.77 or 2.17 Inch
2.76 and 3.54 Inch
>3.94 Inch
5.51 Inch
1.77 or 2.17 Inch
3.54 and 4.33 Inch
1.18 and 1.97 Inch
1. Remove the battery cover, short press `Set`(back panel) or long press `*`, then
the voice prompts: `Please add administrator`.
2. Add admin`s fingerprint(the same fingerprint,3 times), card, or
password (6-8 numbers) and `#`(the same password, 2 times).
3. The voice prompts: `add successfully`.
4. Then you can continue to add.
Notes: 1. The first three are administrator.
2. `*`: Back, Sign out button, `#`: confirm button.
Add The User
1. Remove the battery cover, short press `Set`(back panel) or long press `*`, then
the voice prompts: `Please verify the administrator`.
2. Verify the administrator.
3. Add user`s fingerprint(the same fingerprint,3 times), card, or
password (6-8 numbers) and `#`(the same password, 2 times).
4. The voice prompts: `Add successfully`.
5. Then you can continue to add.
7. Install The Lock
7.1. Install 2 connection columns
on the front panel.
Delete The User
7.2. Install the front panel.
1. Remove the battery cover, short press `Set`(back panel) or long press `*`, then
the voice prompts: `Please verify the administrator`.
2. Verify the administrator.
3. Short press Set(back panel) or long press `*` again.
4. Press `1` to remove all user fingerprints, press `2` to remove all user passwords,
press `3` to remove all user cards, press `4` to remove all users.
5. The voice prompts:`successful`.
a. Insert the suitable square steel into the
Door
lock body.
b. Pass the connection line through the door
hole.
hole of the front panel and fix the front panel
Reset The Lock
on the door, then press the other end of the
1. Remove the battery cover, long press `Set` for 3 seconds.
2. The system restore to the factory default settings.
square steel.
Notes:
1. After the reset, all the information are removed (including administrator).
2. Administrator password will return to its default `1234567890`.
3. Please add a new administrator immediately.
7.3. Install the back panel.
a. Press the front panel, and connect the
interface of the back panel, then Insert
the excess line into the door hole.
b. Insert back locking p addle into the lock
body, and you can cut off one or two
sections of back locking paddle according
to the thickness of the door.
Connection Column
Screws Hole
Door
Square
Steel
Hole
c. Align the square steel with the square
steel hole of the back panel, and compress
Back Locking Paddle
the back panel.
APP Installation
1. Search `tuyaaoni` in APP store, download and install APP.
2. Registration and login with the mobile phone number.
3. Please refer to the operation prompt to complete the network configuration.
Add Network
1. Short press `3`+`#`, Verify the administrator.
2. Network configuration mode: press # to change.
a. Normal mode: the LED of `8` fast flash, please add network in APP.
b. Compatibility mode: the LED of `8` slow flash, please add network in the
Compatibility mode of APP.
3. Add successfully: The voice prompts `add successfully`.
4. Add failure: LED light show `X` and the voice prompts `add failure`.
d. Lock 2 connection column screws to fix the back panel.
e. Install 4 AA batteries and the battery cover, then lock the battery
cover screw.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Note: The administrator can`t be removed by doing this.
c. Align the square steel with the square steel
connection line with the corresponding
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Self-locking
Warranty Card
1. Please fill out the warranty card and keep it well.
2. The warranty period of this product is 18 months.
3. The following belongs to the scope of non warranty:
a. The warranty has expired.
b. Damage occurred during or in relation to non-routine and/or unauthorized
disassembly.
c. Failure to provide a valid proof of purchase when requesting service or repair.
d. Damage occurred as a result of natural disaster.(including earthquake, fire,
flood etc.)
e. Damage occurred due to unexpected factors or man-made reasons.
(including mis-operation, improper insert or pulling, hauling, bumping,
improper voltage input and others)
4. We will charge for the repairing if it is out of warranty.
5. When the product breaks down, ask your local dealer for repair and write
out specific information below.
Product Name
Product Model
Product Price
Date of Purchase
User Name
User Phone
User Address
Seller Name
Seller Phone
Seller Address
If the password is entered wrong for 5 times continuously, the system will be locked
for 180 seconds, and the fingerprint or card unlock can remove self-locking.
Order Number
Low Power Warning
Maintenance records(Filled in by the maintenance agency)
8. Install Buckle Plate A nd Buckle Box
Tapping Screw
Door Frame
When the battery power is lower than 4.8V, the lock will prompt `The battery is use
up, please replace it`, please replace with 4 new batteries in time.
Buckle Plate
Virtual Password
Enter virtual password before or after the real password, it can be unlocked.
Buckle Box
Date
Fault
Result
Signature

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Linotronic
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : Hewlett-Packard
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : Hewlett-Packard
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 2
Create Date                     : 2018:08:29 17:02:19+08:00
Modify Date                     : 2018:08:29 17:02:19+08:00
Producer                        : Corel PDF Engine Version 16.1.0.843
Author                          : Administrator
Creator                         : CorelDRAW X6
Title                           : 未命名 -1

EXIF Metadata provided by EXIF.tools