Firetide 6100-1 HotPort 610X Wireless Mesh Node User Manual Manual
Firetide Inc. HotPort 610X Wireless Mesh Node Manual
Firetide >
Contents
- 1. manual
- 2. Manual
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 866835 |
| Application ID | Ei+0CQbVA75OD0NV2GTBSg== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 59.01kB (737587 bits) |
| Date Submitted | 2007-11-09 00:00:00 |
| Date Available | 2007-11-09 00:00:00 |
| Creation Date | 2007-03-01 06:25:53 |
| Producing Software | Adobe PDF Library 7.0 |
| Document Lastmod | 2007-03-22 13:15:28 |
| Document Title | Manual |
| Document Creator | Adobe InDesign CS2 (4.0.4) |
HotView HotViewProTM Hardware Installation Guide HotPort 6000 Series Indoor and Outdoor Wireless Mesh Nodes Series 6100 - Indoor Node Manual Revision 0.95 022807 The contents of this Installation Guide are subject to change without notice. Please refer to the Firetide web site, www.firetide.com, for current versions. Series 6200 - Outdoor Node Firetide Limited End User Product Warranty Pursuant to all provisions described herein, Firetide hardware products and Firetide antennas are warranted for one (1) year from the date of purchase against defects in the build materials and workmanship. Firetide does not warrant that the Products will meet any requirements or specifications of any End User Customer. This warranty applies to the entire Firetide product, including the AC power adapter. Pursuant to all provisions described herein, Firetide software products are warranted for ninety (90) days from the date of purchase against defects in the build materials and workmanship. Firetide also warrants that the Software will materially conform to the documentation supplied by Firetide with the Software. In the event that the Software fails to materially conform to the documentation and an authorized Firetide reseller is notified in writing of such failure within the warranty period, Firetide or its reseller shall use commercially reasonable efforts to promptly correct the nonconformity. Firetide does not warrant that the use of the Software will be uninterrupted or error free. The above warranties are void if the alleged defect cannot be verified by Firetide or if, as determined by Firetide, the product failure was due to tampering, abuse, misuse, accident, shipping, handling, or storage; or if the product has been installed, used, or maintained in a manner not described in the product user manual; or if the product has been altered in any way; or if product serialization has been altered. Any attempt to disassemble or repair the product by anyone other than Firetide immediately voids this warranty. This warranty applies only to the original End User purchaser of the product and may not be transferred to any other individual or entity. THE FOREGOING ARE THE EXCLUSIVE WARRANTIES APPLICABLE TO THE PRODUCT INCLUDING THE SOFTWARE, AND THE EXCLUSIVE REMEDY FOR DEFECTS IN THE PRODUCT. FIRETIDE DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT OR FIT- NESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES SO TO THAT EXTENT THIS LIMITATION MAY NOT APPLY TO YOU. In no event will Firetide be liable for any special, incidental, consequential, punitive or indirect damages whatsoever (including, without limitation, damages for loss of profits, business interruption, loss of information, or other pecuniary loss) arising out of the use or inability to use the product or the performance, interruption or failure of the product, irrespective of the cause of action, even if Firetide has been advised of the possibility of such damages. Firetide’s cumulative liability for all claims arising out of or in connection with this warranty will not exceed the amount paid by the original End User purchaser to purchase the product. The amounts payable for the product are based in part on these limitations and these limitations shall apply notwithstanding the failure of essential purpose of any remedy. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so to that extent the above limitations or exclusions may not apply to you. By using the product the original End User purchaser agrees to and is bound by these terms and conditions. In the event that a product fails to meet this warranty and Firetide’s authorized reseller is notified in writing of such failure within the warranty period, Firetide shall, at its own discretion, either repair the product or replace it with the same or a functionally-equivalent product free of charge. Replacement products may contain refurbished materials in whole or in part. Firetide will honor this warranty provided the product is returned through an authorized Firetide reseller or dealer with shipping charges prepaid, along with a proof of purchase describing the original purchase date and product serial numbers if applicable. The authorized reseller must acquire a Return Materials Authorization (RMA) number from Firetide prior to returning any product. Firetide does not accept shipments of defective products without shipping charges prepaid. Safety Instructions & Explanation of Graphic Symbols The HotPort outdoor wireless mesh node must be installed by a qualified professional such as a licensed electrician. Failure to install this equipment properly may result in equipment damage and personal injury or death. This symbol is intended to alert the user to the presence of non-insulated dangerous voltage that may be of sufficient magnitude to constitute a risk of lethal electric shock to persons. This symbol is intended to alert the user to the presence of important operating, maintaining and servicing instructions in the literature accompanying the HotPort node. Failing to comply with this instruction may result in electrical shock. This symbol is intended to alert the user to the presence of important operating, maintaining and servicing instructions in the literature accompanying the HotPort node. Failing to comply with this instruction may result in a hazard. Copyright Notice: ©2003-2007 Firetide, Inc. All rights reserved. Trademarks: Firetide, the Firetide logo, Instant Mesh Networks, HotPort, and HotPoint are trademarks of Firetide, Inc. All other trademarks are the property of their respective owners. HotPort 6000 Series Mesh Nodes February 2007 Contents HotPort Node Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Indoor Mesh Node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Antenna Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Compact Disk (CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Outdoor Mesh Node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Antenna Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Compact Disk (CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Planning Your Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Staging Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Required Tools and Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Indoor Node Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Outdoor Node Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Preparing the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Preparing the Site for Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Weatherproofing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Preparing Earth Ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mounting the Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Mounting the Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Pole Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Using Mounting Straps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mounting the Node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Power Options - Outdoor Nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 DC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Building a Custom Ethernet Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Appendix A - Contacting Firetide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Appendix B - Connector Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 HotPort Outdoor Node Ethernet Transition Cable Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Power Connector Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Appendix C - Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Common Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Wireless Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Outdoor Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Indoor Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Appendix D - Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 USA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Canadian Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 February 2007 Firetide Instant Mesh Networks Caution! Risk of electric shock! POWER LINES CAN BE LETHAL Do not install the HotPort outdoor mesh node where possible contact with power lines can be made. Antennas, poles, towers, guy wires, or cables may lean or fall and contact these lines. People may be injured or killed if they are touching or holding any part of equipment when it contacts electric lines. Make sure there is NO possibility that equipment or personnel can come in contact directly or indirectly with power lines. ASSUME ALL OVERHEAD LINES ARE POWER LINES The horizontal distance from a tower, pole or antenna to the nearest power line should be at least twice the total length of the pole/antenna combination. This will ensure that the pole will not contact power if it falls either during or after installation. SURVEYING THE SITE Look over the entire site before beginning any installation and anticipate possible hazards. Never assume anything without checking it out for yourself! Don’t take shortcuts! TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS ABOVE GROUND • Use approved non-conducting ladders, shoes, and other safety equipment. Make sure all equipment is in good repair. • If a tower or pole begins falling, don’t attempt to catch it. Stand back and let it fall. • If anything such as a wire or pole does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by calling the power company. • Don’t attempt to erect antennas or towers on windy days. • MAKE SURE ALL TOWERS AND POLES ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna. The HotPort outdoor node has built-in lightning protection. Be sure that any other equipment connected to the HotPort node also has the same level of protection. • The base of the antenna pole or tower must be connected directly to the building protective ground or to one or more approved grounding rods, using 10 AWG ground wire and corrosion-resistant connectors. • Refer to the National Electrical Code for grounding details. • Select equipment locations that will allow safe and simple in- IF AN ACCIDENT SHOULD OCCUR WITH THE POWER LINES • DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED. stallation. • Don’t work alone. A friend or co-worker can save your life if an accident happens. • Use a non-conductive dry board, stick, or rope to push or drag them so they no longer are in contact with electrical power. • Don’t attempt repair work when you are tired. Not only will you be more careless, but your primary diagnostic tool deductive reasoning - will not be operating at full capacity. • Once they are no longer contacting electrical power, administer CPR if you are certified. • Immediately have someone call for medical help. Do not open the cover • Dangerous voltages inside. • No serviceable parts inside. • Refer to qualified service personnel. • Unit must be disconnected from power prior to servicing. • Unit has tamper-evident labeling that indicates when the cover has been removed. HotPort 6000 Series Mesh Nodes February 2007 HotPort Node Installation This hardware installation guide describes how to install the HotPort node safely. The HotPort is intended to be installed by trained professionals. Be sure to read and understand all installation and safety instructions before proceeding with the installation. Table 1. Summary of HotPort 6000 Series Mesh Nodes Model 6101 6102 6201 6202 Use Indoor, Worldwide, 2.4, 4.9, 5 GHz Indoor, Worldwide, 2.4, 4.9, 5 GHz Outdoor, Worldwide, 2.4, 4.9, 5 GHz Outdoor, Worldwide, 2.4, 4.9, 5 GHz No. of Radios Unpacking The HotPort node package contains the following items. If you are missing any of these items, contact your Firetide reseller. Indoor Mesh Node • HotPort node in plenum-rated enclosure. Antenna Assembly • Two detachable 2.4 Ghz omni-directional antennas. • Two detachable 5 Ghz omni-directional antennas. Note: HotPort nodes come with two pairs of staging antennas. Use these antennas to determine which RF frequency band (2.4 or 5 GHz) to use in your installation location. After you decide, order spectrumspecific (that is, 2.4 or 5 GHz) antennas from Firetide. Firetide offers a range of antennas; refer to the Firetide Antenna Guide for current offerings. Power • Power brick with NEMA5-15 (US) to IEC cord. Other IEC cords are available separately . Note: Series 6100 nodes have an improved, positive-retention DC power cable, and will NOT work with existing Firetide Hotport 3100 and 3500 series power supply bricks. Documentation • 6100 Series Quick Install Guide. • Warranty and registration card. Compact Disk (CD) • HotView software. • HotView Pro User Guide. Outdoor Mesh Node • HotPort node in NEMA-4X enclosure with weatherproof caps. • Two N to reverse-polarity SMA adapters. • Lockable bracket kit for pole and wall mounting. Designed to fit 37 mm to 50 mm (1.5 in to 2.0 in) poles. The mounting bracket also has slots for mounting straps for attaching to larger diameter or irregularly shaped poles. • Weatherized Ethernet transition cable (2 m (6.6 ft)), circular, watertight, IP67-rated female to RJ-45/RJ-45 male connector kit with Bulgin connector housing. Antenna Assembly • Two detachable 2.4 Ghz omni-directional antennas. • Two detachable 5 Ghz omni-directional antennas. Power • Power cord with NEMA 5-15 (US) plug. Other cords are available separately. Note: Series 6200 nodes will work with existing Firetide Hotport 3200 and 3600 series power supply bricks. Documentation • 6200 Series Quick Install Guide. • Warranty and registration card. Compact Disk (CD) • HotView software. • HotPort 6000 Series Hardware Installation Guide • HotView Pro User Guide. • Warranty/Registration Card. • HotPort 6000 Series Hardware Installation Guide. • EULA. • Warranty/Registration Card. • EULA. February 2007 Firetide Instant Mesh Networks Planning Your Installation HotPort 6000 Series nodes are easy to install. They are mechanically compatible with existing HotPort nodes. 6000 Series nodes form their own mesh, however - they will not mesh with 3000 Series nodes. 6200 Series outdoor nodes are improved compared to earlier designs. For new installations, a single weatherproof power cord is provided. No external ‘brick’ is used. The 6200 Series can power up to two peripherals via PoE, as well. For existing installations, the 6200 Series can accept the DC power from supplies used to power 3200 Series and 3600 Series nodes. The 6200 Series will also fit the existing pole mount. Staging Considerations You should set up and test your nodes indoors, on a bench or table, before installing them. This will allow you to pre-configure the nodes so that they are all on the same RF channel, etc. 3. Install the HotView software on a workstation and connect the workstation to a HotPort node (see the HotView User Guide for information about installing and using HotView). 1. Set up your HotPort node in a lab with all other HotPort units using the two provided antennas. 4. Use HotView to configure the HotPort nodes and create a small mesh network. Configure and test the network settings you plan to use. 2. Make all the necessary cable connections and power the HotPort units. Required Tools and Supplies The following tools and supplies must be provided by the customer: • #2 Philips screwdriver • Hose clamps, band clamps, U-bolts, or similar brackets, suitable for mounting the antennas to your chosen antenna mast. If you need to build a custom cable to connect a wired-Ethernet device to your HotPort, you will need an RJ-45 crimping tool and a • Wire cutters to cut tie wraps around cables Catgory 5 Ethernet cable with at least one RJ-45 connector to con• Ladders, lifts, and/or platforms to install the HotPort node on nect a peripheral to the HotPort. poles and structures The following tools and supplies are optional: • 10 AWG grounding cable to connect the HotPort node to earth • Cordless screwdriver #2 Philips ground • Cordless drill • Grounding connectors and grounding rod • Antenna stand (used to mount the antenna pole) • Weatherproofing kit – this kit provides electrical tape and butyl mastic. Check your local distributor for weatherproofing antennas and coaxial cables. • Small adjustable wrench • Hose clamps, band clamps, U-bolts, or similar brackets, suitable for attaching the HotPort node to your chosen antenna mast. HotPort 6000 Series Mesh Nodes February 2007 Indoor Node Installation Figure 1. AC Power Brick Indoor node installation is straightforward. Place the unit on a table or shelf, or use the optional bracket to attach it to a wall, ceiling, or cubicle partition. Attach the antennas, keeping in mind that all antennas on all units should be parallel - typically vertical. Apply power. The power LED should illuminate immediately; after about 60 to 90 seconds, the status LED should switch to steady green. Firetide recommends that you power up and configure all nodes on a table or bench before deployment. Use HotView or HotView Pro to configure your mesh. Note the location of the reset button in the lower right corner of the rear panel. A paperclip can be used to reset the unit after it has fully booted and the status light has come on. Figure 2. Optional Mounting Bracket ?glGgjlÛD]k`ÛEg\] 8mpadaYjqÛ9jY[c]l DYafÛDgmflaf_Û9jY[c]l Figure 3. HotPort 6100 Series Mesh Node - Front View Figure 4. HotPort 6100 Series Mesh Node - Rear View February 2007 Firetide Instant Mesh Networks Outdoor Node Installation Preparing the Unit 1. Pre-assemble the antenna, HotPort node, and other devices to a metal pole and antenna stand and then relocate and attach the entire stand to a roof top. It is often easier to install all devices to one object, such as a pole, and then attach the pole to the roof. In many cases, connecting the devices to a pole already attached to the roof top can be difficult and dangerous. 2. A lightning surge suppressor must be used. Some antennas include one. If not, you must install a lightning surge supressor. 3. Install the antenna and any wireless devices higher than the HotPort node. Take care when locating the HotPort node far away from the antenna; a short antenna cable gives better performance than a longer one. Firetide recommends that you use antenna cables less than 3 meters; if you have an application which requires a long antenna cable, consult the factory. 4. The HotPort node and its antenna must both be grounded. 5. Use weatherproofing kits that include non-vulcanized rubber to weatherproof connectors and antennas. All Ethernet cables must be waterproofed; standard RJ-45 connectors do not last outdoors. 6. Power over Ethernet: Consider which devices require PoE and what the required input voltage will be. 7. Connect peripheral devices to the HotPort node. 8. Connect power to the HotPort node and peripherals. Preparing the Site for Mounting Prior to mounting the antenna and enclosure, prepare the site for mounting as described below. Safety Considerations Consider the following safety issues. • If using a ladder, use approved, non-conducting ladders. • Use approved and non-conducting shoes and other safety equipment. Make sure that all equipment is in good repair. • If mounting to a pole or tower, make sure all poles and towers are securely grounded. • Make sure antenna cables have lightning arrestors. Weatherproofing The two Ethernet ports on the bottom of the HotPort node feature circular, watertight IP67-rated connectors. Use the included weatherized Ethernet transition cable/RJ-45 connector kit to connect Ethernet devices with male RJ-45 connectors to the HotPort node. Be sure to weatherize the entire Ethernet cable, from end to end. Preparing Earth Ground The HotPort node must be properly connected to earth ground. Failure to do so may result in equipment damage, injury, or death. The product warranty does not cover damages resulting in part or in whole from improper grounding. The components that will attract lightning strikes are the antenna, the antenna pole, and the Ethernet and power cables. Below are some guidelines for installing grounding components. HotPort 6000 Series Mesh Nodes • Having a proper ground is critical. The following steps represent minimum acceptable grounding practices. Consult your location’s building and electrical codes regarding antennas and follow them, or consult the National Electric Code (NEC). • If connecting to a tower or pole, connect the base of the tower pole directly to the building’s ground or to one or more approved grounding rods using 10 AWG ground wire and corrosion-resistant connectors. • Connect the grounding cable to rain gutters only if the rain gutter or other conductive material is connected to earth ground. • Grounding rods should be copper and between 6 - 8 ft (1.8 m – 2.4 m) long. • Install all grounding components in straight lines. If bends are unavoidable, do not make sharp turns. • Earth-to-ground 10 ohms. resistance should not be more than • Understanding the soil is very important in order to create a proper earth ground. If your soil is rocky or sandy, drive your ground rods and then pull them back out and dump an approved ground enhancement material into the holes where the grounding rods go. Then replace the grounding rods. Keep in mind that some salt compounds are corrosive and can cause copper to corrode. February 2007 Mounting the Antennas Once you determine which RF band to use, you can order spectrumspecific high-gain antennas from Firetide. • Do not mount the HotPort antennas within 3 ft (0.9 m) of other antennas. If you do, interference may occur. The following material provides some general guideleines for mounting antennas. Refer to the information which came with your antenna for detailed mounting instructions. • Do not mount the antenna pole near power lines. Mounting Guidelines • For best results, the mounting location should be selected to enable maximum performance of the antennas. Generally speaking, a higher antenna will have better overall range and coverage. • Most omnidirectional antennas can be mounted directly to the HotPort node, or directly to a pole. Larger or heavier antennas should be mounted to the pole. • Position the antennas on the pole above the HotPort enclosure. • The antennas should not be within 3 ft (0.9 m) of any metal bar or structure, and ideally not within 3 ft (0.9 m) of any concrete or stone structure. In general, try to locate the antennas as far from such objects as practicable. • HotPorts should not be placed where trees or foliage are in the line-of-sight path between any pair of units. • Shorter antenna cables give better performance. Plan your installation to minimize antenna cable length. However, do not attempt to splice or shorten the antenna cable. If a longer coax cable is required, the system requires a 50 ohm cable. February 2007 • If a longer coax cable is required, contact your local distributor to obtain a 50 ohm cable with the correct connectors. In order to maintain proper system operations, there should be more than 8 dB of insertion loss between the HotPort node and the antenna. Insertion loss is defined as the loss of signal strength when a cable is inserted between the transmitter and the receiver. Insertion loss is measured in dB. • When mounting next to an access point, mount the access point lower on the pole and at least 3 ft (0.9 m) from the antennas. You can also mount the access point on a horizontal bar to achieve the required 3 foot separation. Wall Mounting • Position the antennas above or to the side of the HotPort enclosure to permit easy attachment of the antenna to the connector at the bottom of the enclosure. • RF signals can be attenuated by a wall or the composition of a building. When utilizing omni-directional antennas, connecting the antennas to a wall may limit the amount of coverage. Firetide Instant Mesh Networks Mounting the Bracket The HotPort enclosure should be mounted securely to a wall/wood structure or a pole approximately 1.5” (37 mm) to 2” (50 mm) in diameter. You can also mount the enclosure to a wall, light poles, and irregularly shaped poles. Series 6200 outdoor nodes will fit existing Series 3200 and 3600 brackets. The brackets have been designed with multiple holes and slots to allow mounting with bolts, straps, or other methods. Mounting Guidelines 1. For best results, the location should enable maximum performance of the antenna and any attached devices, such as access points or cameras. When possible, provide clear line-ofsight access for the antennas. You can test various locations by mounting the unit to a portable stand until you can determine the ideal location for permanent mounting. 2. The location must allow for a solid connection to earth ground. Be sure the earth ground wire or strap does not obstruct access to the enclosure. 4. Attach the enclosure to the universal mounting bracket by sliding the metal clips on the back of the enclosure into the metal straps on the universal mounting bracket. 5. Secure the enclosure to the universal mounting bracket using the four captive screws on the sides of the universal mounting bracket. Figure 5. Universal Mounting Bracket Attached to Pole 3. The unit must be within reach of the power cord. A two-meter AC cord is provided, or a DC cord may be used. Series 6000 nodes will work with power supplies from Series 3000 nodes, but cannot be powered over Ethernet. Wall Mounting 1. The Universal Mounting Bracket, shown in Figure 5, contains holes and slots to allow it to be mounted via U-bolts or straps. Furthermore, it can be mounted on either a horizontal pole or a vertical pole. Use four screws to attach the universal mounting bracket securely to the wall using the four holes near the top and bottom of the universal mounting bracket. Use appropriate anchors when attaching to masonry or other materials. 2. Attach the enclosure to the universal mounting bracket by sliding the metal clips on the back of the enclosure into the metal straps on the universal mounting bracket. 3. Secure the enclosure to the universal mounting bracket using the four captive screws on the sides on the universal mounting bracket. Using Mounting Straps For poles with diameters larger than 2” (50 mm), horizontal poles, irregularly shaped poles, or lighting lamps, you can use mountPole Mounting ing straps to mount the HotPort enclosure. Position the universal You can mount the HotPort node to a pole using U-bolts. The sec- mounting bracket against the pole. tion below describes how to mount the enclosure to a 1.5” (37 mm) 1. Thread two mounting straps around the pole and through the or 2” (50 mm) pole.Position the pole mounting bracket against the slots located near the top and bottom of the universal mountpole. Insert the U-bolts from behind the pole and through the pole ing bracket. Secure the mounting straps. mounting bracket. 2. Attach the enclosure to the universal mounting bracket by slidYou installation kit includes a small T-handle socket wrench which ing the metal clips on the back of the enclosure into the metal fits the supplied nuts. straps on the universal mounting bracket. 1. Insert the two U-bolts through the four holes near the top and Secure the enclosure to the universal mounting bracket using the bottom of the universal mounting bracket. four captive screws on the sides of the universal mounting bracket. 2. On each U-bolt threaded shaft, place a washer, a lock washer, and one or more 6 mm nuts as spacers. Smaller pole diameters usually require a spacer nut to hold the bracket away from the U-bolt clamp. 3. Use four lock washers and 6 mm nuts to secure the universal mounting bracket, pole mounting bracket, and U-bolts assembly. 10 HotPort 6000 Series Mesh Nodes February 2007 Mounting the Node Attach the supplied backing plate to the HotPort node, using the Then tighten the four captive screws on the node assembly. This supplied screws. Note that the holes in the node are pre-tapped for locks the node onto the bracket. Don’t leave these screws loose; if the supplied metric screws; do not use other screws. you do, it’s easy to knock the node off the bracket. Next, slide the node assembly onto the bracket, so that the four tabs on the node assembly engage the straps on the bracket, as shown in the photo. Figure 7. Tighten Screws Figure 6. Mounting the Node February 2007 Firetide Instant Mesh Networks 11 Connecting Cables After your node is securely mounted, attach the two antennas, the If you are using your Series 6200 with a companion Firetide Hotpower cable, and any Ethernet cables you need, as shown in Figures Point access point, a special Ethernet cable is available to connect 8 and 9. the two units and to supply PoE power to the AP. The cable is shown Figure 8. Connected Outdoor Node in Figure 10. Note the locations of the reset button under the weatherproof cap, just below Ethernet port 3. To perform a factory reset on the unit, power it on and wait for the status light to come on. Then press the reset button. Figure 9. HotPort Node Bottom Panel Figure 10. Ethernet Cable for HotPort-HotPoint AP Connection 12 HotPort 6000 Series Mesh Nodes February 2007 Power Options - Outdoor Nodes Power Supply DC Power The power supply can provide power to the HotPort enclosure from In addition to its AC input, the 6200 Series features a DC input. It an AC outlet. The power supply is rated for 90-240 VAC. is compatible with older 3200 Series external power supplies, so if you are upgrading an older node, you may re-use the supply if conPowering Other Ethernet Devices venient. Ports 2 and 3 on a 6200 Series node can provide Power over EtherThe 6200 Series does not care what the source of DC power is. If denet (PoE) functionality to Powered Devices (PD) connected to these sired, you may use batteries, solar panels, or any other source of DC ports. (Port 1 cannot.) A Powered Device can receive data and the power at the correct voltage. Contact your Firetide dealer for more power to process the data from the HotPort node, which functions information on their solutions. as Power Sourcing Equipment (PSE) in this configuration. To receive power from a HotPort node, the device must support the IEEE Do not connect both AC and DC supplies simultaneously. 802.3af standard, which defines PoE functionality. Building a Custom Ethernet Cable Firetide supplies a cable that will connect your 6200 Series node directly to a HotPoint Access Point. To connect to other devices, you will need to assemble an adapter cable. To assist in this, Firetide supplies a weatherized Ethernet transition cable, which is PoE compatible. A weatherized RJ-45 coupler is also included. To connect power to the unit from PSE: Note: Regardless of your exact configuration of Ethernet cable and power sources, you must make sure all cables and connections are completely waterproofed. It is a good installation practice to leave enough cable slack so that there is a drip loop in each cable. This provides a low point for water to drip off the cable, rather that running down to a connector. 1. Construct a shielded Category 5 Ethernet cable: 2. Insert one end of the Ethernet cable (without an RJ-45 connector) through the provided coupler housing. 3. Use an RJ-45 crimping tool to attach an RJ-45 connector to this end of the Ethernet cable. Figure 11. Waterproof RJ-45 Coupler 4. Insert the male RJ-45 connector on the constructed Ethernet cable into the female-to-female Ethernet coupler. 5. Connect the male RJ-45 connector on the Firetide-supplied Ethernet transition cable to the female-to-female coupler. 6. Remove the protective cap from an Ethernet port on the HotPort enclosure and insert the circular, 10-pin connector on the Ethernet transition cable. 7. Tighten all connectors to ensure a watertight seal. Figure 12. Waterproof Ethernet Cable February 2007 Firetide Instant Mesh Networks 13 Appendix A - Contacting Firetide Dealer Provided Technical Support and Warranty Services Sales Assistance If you need additional technical assistance, please contact your Firetide dealer directly. All authorized Firetide dealers are trained and authorized to provide technical support and warranty services for our products and have qualified technical staff available to help you build and maintain your Firetide mesh network. If you need additional HotPort wireless mesh nodes or accessories, please contact your Firetide dealer directly. If you do not know your dealer’s name, simply email sales@firetide.com and we will send you the dealer information you need. To help us provide the best service possible, be sure to include your phone number, address, and the serial numbers of the HotPort nodes at your location. Firetide Provided Technical Support You can also get technical support from Firetide. Simply email support@firetide.com, or call 1-877-FIRETIDE, extension 2, or +1 408 399 7771. Product Returns Please contact your Firetide dealer for instructions on returning defective or damaged products for repair or replacement. Do not return products to Firetide, Inc. Please keep all original packaging materials in the event they are needed to return the product for servicing. 14 HotPort 6000 Series Mesh Nodes February 2007 Appendix B - Connector Wiring HotPort Outdoor Node Ethernet Transition Cable Pin Descriptions Table 2. Circular, Watertight IP66-Rated Connector and Port Pin Descriptions Connector Pin # Wire Color Port Pin # White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown Drain Wire Drain Wire 10 10 Table 3. RJ-45 Connector Pin Descriptions Pin # Signal Description TXD+ TX Data 10 BaseT/100 BaseTX TXD- TX Data 10 BaseT/100 BaseTX RXD+ RX Data 10 BaseT/100 BaseTX PoE+ +48 VDC PoE Power PoE+ +48 VDC PoE Power RXD- RX Data 10 BaseT/100BaseTX PoE- -48 VDC PoE Power PoE- -48 VDC PoE Power Power Connector Pin Descriptions Figure 13 shows the pinout of the power connectors used to supply power to Series 6100 nodes (left) and Series 6200 nodes (right). Each view is of the cable connector, as viewed end-on. If you wish to construct a cable to supply power to a Series 6200 node with a Series 6100 node indoor power supply, you can do so by wiring as shown in Figure 13. Likewise, other cables can be constructed for custom applications, as long as the wiring shown is followed. In all cases, DC power to a HotPort node must be 15 VDC ±15%, up to 3A. Series 6200 HotPort nodes can provide PoE-compliant 48 VDC power to other devices. Figure 13. Power Transition Cable Pin 1 brown power Pin 2 Pin 3 black February 2007 white ground/drain Male - End View Pin 4 Connect to Power Supply Pin 4 blue Pin 3 Female - End View Connect to 6200 Series HotPort Firetide Instant Mesh Networks 15 Appendix C - Specifications Common Specifications Supported Data Rates & Standards Wireless Interface • 802.11a 6/9/12/18/24/36/48/54Mbps + 108Mbps (Turbo Mode) except Japan These tables describes the technical limits of the nodes. Various country restrictions may further limit available choices. • 802.11a Capable of switching to 1⁄4 and 1⁄2 rates for 4.940 – 4.990 GHz Public Safety Band Model 6101 6102 6201 6202 Use Indoor, Worldwide, 2.4, 4.9, 5 GHz Indoor, Worldwide, 2.4, 4.9, 5 GHz Outdoor, Worldwide, 2.4, 4.9, 5 GHz Outdoor, Worldwide, 2.4, 4.9, 5 GHz For all models: Bands (GHz) Frequency (GHz) 802.11a 5.15-5.25 Restrictions 5.25-5.35 802.11b/g 802.11a Japan only 4.94-4.990 5.470-5.725 US Public Safety ETSI 301.893, U-NII 2.412-2.484 5.725-5.825 UNII-3 Max TX Power 26dBm/6-24Mbps 26dBm/36Mbps 24dBm/48Mbps 23dBm/54Mbps 802.11b 802.11g 5.470-5.735 UNII 5.25-5.36 M UNII-2 5.15-5.25 UNII-1 • 802.11b 1/2/5.5/11Mbps • 802.11g 6/9/12/18/24/36/48/54Mbps • Network Standards: IEEE 802.11a/b/d/g/e/f/h/i • Dynamic Frequency Selection (DFS) capable in conjunction with Firetide Software application • Transmit Power Control (TPC) capable in conjunction with Firetide Software application Mesh Protocol 5.725-5.825 4.9-5.090 Bands (GHz) No. of Radios 23 dBm 6-54 Mbps 23 dBm 6-54 Mbps 17 dBm 6-54 Mbps 24 dBm/all rates 26dBm/6-24Mbps 26dBm/36Mbps 25dBm/48Mbps 24dBm/54Mbps • Firetide AutoMesh Protocol Mesh Management Software • HotView mesh management software (bundled) • HotView Pro™ mesh management software (optional) Security & Encryption • Security: WPA—64/128/152 w/TKIP, AES, IEEE 802.1x (LEAP) Antennas • Two detachable omni directional, vertical polarization, dual band antennas • Single detachable, high gain, spectrum-specific, omni directional and directional antennas available (order separately). See Firetide Antenna Guide. Regulatory Agency Certifications • Contact your Firetide dealer for product availability and certifications for your country. 16 HotPort 6000 Series Mesh Nodes February 2007 Outdoor Unit Specifications Indoor Unit Specifications Network Ports Network Ports • Three 10/100 Mbps Ethernet ports with weatherproof connec- • Four 10/100 Mbps Ethernet ports with LEDs tors, LED activity indicator • IEEE 802.3, 802.3u compliant • IEEE 802.3, 802.3u compliant • CSMA/CD 10/100 autosense • CSMA/CD 10/100 autosense Enclosure • Ports 2, 3 PSE Power over Ethernet per 802.3af • Plenum-rated metal enclosure Enclosure • Two RP-SMA antenna connectors • Cast aluminum NEMA-4X/IP66 enclosure • One DC power connector • Two N-type antenna connectors • Four Ethernet connectors • Two weatherproof power connectors (AC and DC) • System indicator LEDs: power, status, per-radio mesh • Three weatherproof Ethernet connectors • Weight: 3 lbs (1.4 Kg) • System indicator LEDs (power, status, mesh (per radio)) • Dimensions: 9.4” x 6” x 1.8” (238 x 152 x 48 mm) • Weight: 12 lbs (5.5 Kg) with bracket Power • Dimensions: 8.8” x 11.2” x 4” (220 x 280 x 100 mm) • DC Input: 15 VDC ±15%, 3 A Power • AC Input: 90-240 VAC, 50-60 Hz, 0.9A • DC Input: 15 VDC ±15%, 3 A • Port 2: IEEE 802.3af compliant PoE (PSE), 13.5 W max • Port 3: IEEE 802.3af compliant PoE (PSE), 13.5 W max Environmental Specifications • Operating temperature: -40º C to +60ºC • Storage temperature: -40º C to +85º C • Humidity (non-condensing): 10% to 90% • Storage humidity (non-condensing): 5% to 95% • Maximum altitude 15,000 feet (4600 meters) Included Accessories Environmental Specifications • Operating temperature: 0º C to +60ºC • Storage temperature: -20º C to +70º C • Humidity (non-condensing): 10% to 90% • Storage humidity (non-condensing): 5% to 95% • Maximum altitude 15,000 feet (4600 meters) Included Accessories • AC power adapter • Staging antennas, 1 pair Optional Accessories • Wall or cubicle-mount bracket • Bracket for pole and wall mounting • External power cord • Removable sun shield • One weatherized Ethernet transition cable with watertight RJ45 coupling. Additional cable kits may be ordered. • Staging antennas, 1 pair Optional Accessories •Outdoor weatherproof Ethernet cable for use with HotPoint APs •Luminaire photocell socket power tap February 2007 Firetide Instant Mesh Networks 17 Appendix D - Regulatory Notices USA FCC Radiation Exposure Statement To ensure compliance with the FCC’s RF exposure limits, the antenna used for this transmitter must be installed to provide a separation This device complies with Part 15 of the FCC Rules. Operation is sub- distance of at least 90 cm from all persons and must not be co-located or operated in conjunction with any other antenna or transject to the following two conditions: mitter. Installers and end users must follow these installation in• This device may not cause harmful interference. structions. • This device must accept any interference received, including interference that may cause undesired operation. Installation FCC Class A Notice Antenna(s) for this unit must be installed by a qualified professional. Operation of the unit with non- approved antennas is a violation This equipment has been tested and found to comply with the limits of U. S. FCC Rules, Part 15.203(c), Code of Federal Regulations, Title for a Class A digital device, pursuant to Part 15 of the FCC Rules. 47. These limits are designed to provide reasonable protection against harmful interference in an office installation. This equipment gen- Canadian Compliance Statement erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause This Class A Digital apparatus meets all the requirements of the Caharmful interference to radio communications. However, there is no nadian Interference-Causing Equipment Regulations. Cet appareil guarantee that interference will not occur in a particular installa- numerique de la classe A respecte les exigences du Reglement sur tion. If this equipment does cause harmful interference to radio or le material broilleur du Canada. This device complies with Class A television reception, which can be determined by turning the equip- Limits of Industry Canada. Operation is subject to the following two ment off and on, the user is encouraged to try to correct the inter- conditions: ference by one or more of the following measures: 1. This device may not cause harmful interference, and FCC Part 15 Note • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. 2. This device must accept any interference received, including interference that may cause undesired operation. • Connect the equipment into an outlet on a circuit different from Firetide HotPoint 6100 and 6200 wireless mesh nodes are certified to the requirements of RSS-210 for 2.4 and 5 GHz spread spectrum that to which the receiver is connected. devices. The use of this device in a system operating either partially • Consult the dealer or an experienced radio/television technician or completely outdoors may require the user to obtain a license for for help. the system according to the Canadian regulations. For further information, contact your local Industry Canada office. FCC Part 90 Note This equipment has been tested pursuant to FCC Part 90, DSRC-C mask certification, and is approved for use in the US on Public Safety bands by licensed Public Safety agencies. Public Safety Band Pursuant to Part 90.1215, use of antennas with gain greater than 9 dBi and up to 26 dBi in the 4.940 - 4.990 GHz Public Safety band is permissible without reduction of TX output power. The antenna shall have a directional gain pattern in order to meet the requirement of point to point and point to multi-point operation. Modifications Any modifications made to this device that are not approved by Firetide, Inc. may void the authority granted to the user by the FCC to operate this equipment. 18 HotPort 6000 Series Mesh Nodes February 2007 February 2007 Firetide Instant Mesh Networks 19
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 20 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:0a507acf-ccaf-48be-9ed2-5c47e9e6e7a4 Producer : Adobe PDF Library 7.0 Trapped : False Create Date : 2007:03:01 06:25:53-08:00 Metadata Date : 2007:03:22 13:15:28-07:00 Modify Date : 2007:03:22 13:15:28-07:00 Creator Tool : Adobe InDesign CS2 (4.0.4) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 8727 bytes, use -b option to extract) Instance ID : uuid:599a3d5d-9c56-4525-9dea-7fedfdd79187 Rendition Class : proof:pdf Document ID : adobe:docid:indd:8205f886-c804-11db-9a53-aff64cfa8412 Derived From Instance ID : f87c4b0c-c792-11db-9a53-aff64cfa8412 Derived From Document ID : adobe:docid:indd:f87c4b09-c792-11db-9a53-aff64cfa8412 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 300.00, 180.00, 72.00, 300.00, 180.00, 600.00, 72.00, 600.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 300.00, 180.00, 72.00, 300.00, 180.00, 600.00, 72.00, 600.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:0226bec5-00a7-11db-8562-000393db07a6, uuid:6b2d7e20-a7fd-11db-8f54-000a958e60a8, uuid:B98EDC6DC8F111DB8FE0EE2B432BE2A4, uuid:B98EDC68C8F111DB8FE0EE2B432BE2A4, uuid:7699646AC8F111DB8FE0EE2B432BE2A4, uuid:883014DA919411DBB7ACE3B8920B9ABE, uuid:5FD2AA45C90111DB8FE0EE2B432BE2A4, uuid:6D524257A6FC11DB95C8F6A94D1ED1BA, uuid:9eb99102-af55-11db-babf-000a958e60a8, uuid:d1c7523a-af54-11db-babf-000a958e60a8, uuid:0226bec5-00a7-11db-8562-000393db07a6 Manifest Reference Document ID : uuid:0226b728-00a7-11db-8562-000393db07a6, adobe:docid:photoshop:0b5db25e-a11d-11db-b792-c1dcd2cf3921, adobe:docid:photoshop:fc7eeda1-a114-11db-b792-c1dcd2cf3921, uuid:ae9a9668-e8bf-11d9-985a-000a95b68676, adobe:docid:photoshop:0b5db25e-a11d-11db-b792-c1dcd2cf3921, adobe:docid:photoshop:5ab4214c-a032-11db-b26b-ca72b111c917, uuid:B98EDC6CC8F111DB8FE0EE2B432BE2A4, uuid:B98EDC67C8F111DB8FE0EE2B432BE2A4, uuid:76996469C8F111DB8FE0EE2B432BE2A4, uuid:02359D14919411DBB7ACE3B8920B9ABE, uuid:5FD2AA44C90111DB8FE0EE2B432BE2A4, uuid:6D524256A6FC11DB95C8F6A94D1ED1BA, adobe:docid:photoshop:36535611-f616-11d9-9632-cf06f4d71d51, adobe:docid:photoshop:3653561a-f616-11d9-9632-cf06f4d71d51, adobe:docid:photoshop:4806fe07-f61f-11d9-9632-cf06f4d71d51, adobe:docid:photoshop:4806fe00-f61f-11d9-9632-cf06f4d71d51, uuid:4B703E27A96511DB87DEC770C523C36B, uuid:0F13725D8ECB11DB9C7BCA4243CC80C7, uuid:0226b728-00a7-11db-8562-000393db07a6 Format : application/pdf Tagged PDF : Yes Creator : Adobe InDesign CS2 (4.0.4)EXIF Metadata provided by EXIF.tools