Firetide 7100-1 Hotport Model 7100 Mesh Node User Manual Manual
Firetide Inc. Hotport Model 7100 Mesh Node Manual
Firetide >
Contents
- 1. Revised Manual
- 2. Manual
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1224030 |
| Application ID | olvf/7tVb8SWFza3j+rj/Q== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 78.36kB (979510 bits) |
| Date Submitted | 2010-01-07 00:00:00 |
| Date Available | 2010-01-07 00:00:00 |
| Creation Date | 2010-01-07 12:42:21 |
| Producing Software | Adobe PDF Library 9.0 |
| Document Lastmod | 2010-01-07 12:42:29 |
| Document Title | Manual |
| Document Creator | Adobe InDesign CS4 (6.0.4) |
Hardware Installation Guide HotPort HotPort Series 7000 Indoor and Outdoor Wireless Mesh Nodes mesh radio 1 mesh radio 2 status power HotPort 7100 - Indoor Node Manual Revision 1.01-DRAFT 2010-01-07 The contents of this Installation Guide are subject to change without notice. Please refer to the Firetide partners web site, partners.firetide.com, for current versions. HotPort 7200 - Outdoor Node Firetide Limited End User Product Warranty Pursuant to all provisions described herein, Firetide hardware products and Firetide antennas are warranted for one (1) year from the date of purchase against defects in the build materials and workmanship. Firetide does not warrant that the Products will meet any requirements or specifications of any End User Customer. This warranty applies to the entire Firetide product, including the AC power adapter. Pursuant to all provisions described herein, Firetide software products are warranted for ninety (90) days from the date of purchase against defects in the build materials and workmanship. Firetide also warrants that the Software will materially conform to the documentation supplied by Firetide with the Software. In the event that the Software fails to materially conform to the documentation and an authorized Firetide reseller is notified in writing of such failure within the warranty period, Firetide or its reseller shall use commercially reasonable efforts to promptly correct the nonconformity. Firetide does not warrant that the use of the Software will be uninterrupted or error free. The above warranties are void if the alleged defect cannot be verified by Firetide or if, as determined by Firetide, the product failure was due to tampering, abuse, misuse, accident, shipping, handling, or storage; or if the product has been installed, used, or maintained in a manner not described in the product user manual; or if the product has been altered in any way; or if product serialization has been altered. Any attempt to disassemble or repair the product by anyone other than Firetide immediately voids this warranty. FRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES SO TO THAT EXTENT THIS LIMITATION MAY NOT APPLY TO YOU. In no event will Firetide be liable for any special, incidental, consequential, punitive or indirect damages whatsoever (including, without limitation, damages for loss of profits, business interruption, loss of information, or other pecuniary loss) arising out of the use or inability to use the product or the performance, interruption or failure of the product, irrespective of the cause of action, even if Firetide has been advised of the possibility of such damages. Firetide’s cumulative liability for all claims arising out of or in connection with this warranty will not exceed the amount paid by the original End User purchaser to purchase the product. The amounts payable for the product are based in part on these limitations and these limitations shall apply notwithstanding the failure of essential purpose of any remedy. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so to that extent the above limitations or exclusions may not apply to you. By using the product the original End User purchaser agrees to and is bound by these terms and conditions. In the event that a product fails to meet this warranty and Firetide’s authorized reseller is notified in writing of such failure within the warranty period, Firetide shall, at its own discretion, either repair the product or replace it with the same or a functionally-equivalent product free of charge. Replacement products may contain refurbished materials in This warranty applies only to the original End User purchaser of the prod- whole or in part. Firetide will honor this warranty provided the product is uct and may not be transferred to any other individual or entity. returned through an authorized Firetide reseller or dealer with shipping THE FOREGOING ARE THE EXCLUSIVE WARRANTIES APPLICABLE TO THE charges prepaid, along with a proof of purchase describing the original PRODUCT INCLUDING THE SOFTWARE, AND THE EXCLUSIVE REMEDY FOR purchase date and product serial numbers if applicable. The authorized DEFECTS IN THE PRODUCT. FIRETIDE DISCLAIMS ALL OTHER WARRANTIES, reseller must acquire a Return Materials Authorization (RMA) number from WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT Firetide prior to returning any product. Firetide does not accept shipNOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, NON-IN- ments of defective products without shipping charges prepaid. Safety Instructions The HotPort outdoor wireless mesh node must be installed by a qualified professional such as a licensed electrician. Failure to install this equipment properly may result in equipment damage and personal injury or death. This symbol is intended to alert the user to the presence of non-insulated dangerous voltage that may be of sufficient magnitude to constitute a risk of lethal electric shock to persons. This symbol is intended to alert the user to the presence of important operating, maintaining and servicing instructions in the literature accompanying the HotPort node. Failing to comply with this instruction may result in electrical shock. This symbol is intended to alert the user to the presence of important operating, maintaining and servicing instructions in the literature accompanying the HotPort node. Failing to comply with this instruction may result in a hazard. Copyright Notice: ©2003-2010 Firetide, Inc. All rights reserved. Trademarks: Firetide, the Firetide logo, Instant Mesh Networks, HotPort, and HotPoint are trademarks of Firetide, Inc. All other trademarks are the property of their respective owners. HotPort Series 7000 Mesh Nodes January 2010 Contents HotPort Node Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Planning Your Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Indoor Node Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Positioning Indoor Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Outdoor Node Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Preparing the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Preparing Earth Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Antenna Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mounting Outdoor Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mounting Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Mounting the Universal Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Using Mounting Straps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Power Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Appendix A - Contacting Firetide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Appendix B - Connector Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 HotPort Outdoor Node AC Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 HotPort Outdoor Node DC Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Custom Power Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Appendix C - Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Common Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Wireless Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Series 7200 Outdoor Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Series 7100 Indoor Unit Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Appendix D - Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 USA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Canadian Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 January 2010 Firetide Instant Mesh Networks 3 Caution! Risk of electric shock! POWER LINES CAN BE LETHAL Do not install the HotPort outdoor mesh node where possible contact with power lines can be made. Antennas, poles, towers, guy wires, or cables may lean or fall and contact these lines. People may be injured or killed if they are touching or holding any part of the equipment when it contacts electric lines. Make sure there is NO possibility that equipment or personnel can come in contact directly or indirectly with power lines. ASSUME ALL OVERHEAD LINES ARE POWER LINES The horizontal distance from a tower, pole or antenna to the nearest power line should be at least twice the total length of the pole/antenna combination. This will ensure that the pole will not contact power if it falls either during or after installation. SURVEYING THE SITE Look over the entire site before beginning any installation and anticipate possible hazards. Never assume anything without checking it out for yourself! Don’t take shortcuts! • If a tower or pole begins falling, don’t attempt to catch it. Stand back and let it fall. • If anything such as a wire or pole does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by calling the power company. • Don’t attempt to erect antennas or towers on windy days. • MAKE SURE ALL TOWERS AND POLES ARE SECURELY GROUNDED, AND ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE LIGHTNING ARRESTORS. This will help prevent fire damage or human injury in case of lightning, static build-up, or short circuit within equipment connected to the antenna. The HotPort outdoor node has built-in lightning protection. Be sure that any other equipment connected to the HotPort node also has the same level of protection. • The base of the antenna pole or tower must be connected directly to the building protective ground or to one or more approved grounding rods, using 10 AWG ground wire and corrosion-resistant connectors. TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT • Refer to the National Electrical Code for grounding details. IF AN ACCIDENT SHOULD OCCUR WITH THE POWER LINES: HEIGHTS ABOVE GROUND • Select equipment locations that will allow safe and simple installation. • Don’t work alone. A friend or co-worker can save your life if an accident happens. • Don’t attempt repair work when you are tired. Not only will you be more careless, but your primary diagnostic tool deductive reasoning - will not be operating at full capacity. • DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED. • Use a non-conductive dry board, stick, or rope to push or drag them so they no longer are in contact with electrical power. • Once they are no longer contacting electrical power, administer CPR if you are certified. • Immediately have someone call for medical help. • Use approved non-conducting ladders, shoes, and other safety equipment. Make sure all equipment is in good repair. Do not open the cover • Dangerous voltages inside. • No serviceable parts inside. • Refer to qualified service personnel. • Unit must be disconnected from power prior to servicing. • Unit has tamper-evident labeling that indicates when the cover has been removed. HotPort Series 7000 Mesh Nodes January 2010 HotPort Node Installation This hardware installation guide describes how to install the HotPort node safely. The HotPort is intended to be installed by trained professionals. Be sure to read and understand all installation and safety instructions before proceeding with the installation. Table 1. Summary of HotPort Series 7000 Mesh Nodes Model 7100 7200 Use Indoor, Worldwide, 2.4, 4.9, 5 GHz Outdoor, Worldwide, 2.4, 4.9, 5 GHz No. of Radios 1 or 2 1 or 2 This guide covers both dual-radio and single radio models. The only difference between dual-radio models and single-radio models is the second radio. Single radio models will identify themselves in software as 7101 or 7201; dual radio models will identify themselves as 7102 or 7202. Package Contents The HotPort node package contains the following items. If you are missing any of these items, contact your Firetide reseller. HotPort 7100 Indoor Mesh Node • HotPort node in plenum-rated enclosure. Antennas HotPort 7200 Outdoor Mesh Node • HotPort node in NEMA-4X enclosure with weatherproof caps. • Six N to reverse-polarity SMA adapters. • Mounting bracket for pole and wall mounting. Designed to fit 37 mm to 50 mm (1.5 in to 2.0 in) poles. • Six detachable 2.4 GHz 5 dBi omnidirectional antennas. • Six detachable 5 GHz 5 dBi omnidirectional antennas. • These are the only antennas approved for use with the 7100 in Mounting Kit the 2.4, 4.9, and 5 GHz bands.. • U-Bolts, M6x1.0-80mm, with flat washers, split washers, nuts. • Claw-tooth pole grippers. Power • M6x1.0-40mm hex bolt. • External power module with NEMA5-15 (US) to IEC-320 cord. • M6x1.0-20mm hex bolt. Other IEC cords are available separately. • Hex-head socket wrench. Documentation • HotPort 7100 Quick Install Guide. • Warranty and registration card. Compact Disk (CD) • HotView Pro software. • HotView Pro Reference Guide. • HotPort 7000 Hardware Installation Guide • Warranty/Registration Card. • EULA. Antennas • Six detachable 2.4 GHz indoor omnidirectional antennas. • Six detachable 5 GHz indoor omnidirectional antennas. Power • AC power cord with NEMA 5-15 (US) plug. Other IEC cords are available separately. Documentation • HotPort 7200 Quick Install Guide. • Warranty and registration card. Compact Disk (CD) • HotView Pro software. • HotView Pro Reference Guide. • HotPort Series 7000 Hardware Installation Guide. • Warranty/Registration Card. • EULA. January 2010 Firetide Instant Mesh Networks 5 Planning Your Installation Staging Considerations You should set up and test your nodes indoors, on a bench or table, before installing them. This will allow you to pre-configure the nodes so that they are all on the same RF channel, etc. You will use HotView Pro to configure the HotPort nodes and create a small mesh network. Test the network settings you plan to use. Warning: The staging antennas provided with Firetide outdoor nodes are for temporary use only. They MUST be replaced with outdoor-rated antennas as soon as the mesh is staged and operational. The staging antennas are NOT waterproof and NOT moisture resistant. If used outdoors, the antennas may fail. Your CD has a copy of Firetide’s Accessory Guide. Contact your 1. Check to see that all nodes are visible in HotView Pro. If not, Firetide Reseller for assistance in selecting and ordering outdoor troubleshoot per directions in the HotView Reference Guide. antennas suitable for your application(s). 2. Set the Country Code for your country of operation. 3. Re-verify that all nodes are visible, and verify that dual-radio nodes have both radios correctly meshed. Indoor Node Installation Indoor node installation is straightforward. Firetide recommends that you power up and configure all nodes on a table or bench before deployment. Use HotView or HotView Pro to configure your mesh. Place the unit on a table or shelf. Apply power. The power LED should illuminate immediately; after about 60 to 90 seconds, the status LED should switch to steady green. Note the location of the reset button in the lower right corner of the rear panel. To reset the unit, apply power and wait until the unit has fully booted and the status light has come on. Then use a paperclip to press and hold the reset button until the status LED blinks. Positioning Indoor Antennas Figure 2. HotPort Series 7100 Mesh Node - Front View mesh radio 1 mesh radio 2 status power Figure 3. HotPort Series 7100 Mesh Node - Rear View The Firetide-supplied antennas are rated for use in dry, indoor environments. If the antenna is exposed to weather, moisture, or high humidity, it may fail. Use an approved outdoor-rated antenna instead. MIMO technology takes advantage of signal reflections to improve performance. Antenna orientation affects this. Firetide recommends that you begin deployment with the antennas on each radio parallel and in the same plane as the node itself. Depending on performance, you may wish to try other orientations. Figure 1. Staging Antennas Figure 4. Power Supply HotPort Series 7000 Mesh Nodes January 2010 Outdoor Node Installation Preparing the Unit 1. Pre-assemble the antenna, HotPort node, and other devices to a metal pole and antenna and then relocate and attach it to a roof top. It is often easier to install all devices to one object, such as a pole, and then attach the pole to the roof. In many cases, connecting the devices to a pole already attached to the roof top can be difficult and dangerous. WARNING The staging antennas provided with Firetide outdoor nodes and access points are for temporary use only. They MUST be replaced with outdoor-rated antennas as soon as the mesh is staged and operational. The staging antennas are NOT waterproof or moisture resistant. If 2. A lightning surge suppressor must be used. Some antennas used outdoors or in humid environments, the antennas may fail. include one. If not, you must install a lightning suppressor. Your CD has a copy of Firetide’s Accessory Guide. Contact your 3. Install the antenna and any wireless devices higher than the Firetide Reseller for assistance in selecting and ordering outdoor HotPort node. Take care when locating the HotPort node far antennas suitable for your application(s). away from the antenna; a short antenna cable gives better performance than a longer one. Firetide recommends that you Tools Needed use antenna cables less than 3 meters. For HotPort 7200 outdoor nodes, you will need: 4. The HotPort node and its antenna must both be grounded. • #2 Phillips screwdriver. 5. Use weatherproofing kits that include non-vulcanized rubber to weatherproof connectors and antennas. All Ethernet cables • Small adjustable wrench. must be waterproofed; standard RJ-45 connectors do not last • Wire cutters to cut tie wraps around cables. outdoors. • Weatherproofing kit – this kit provides electrical tape and butyl 6. Power over Ethernet: Consider which devices require PoE and mastic. what the required input voltage will be. Depending on the installation location, you may need ladders, a 7. Connect peripheral devices to the HotPort node. lift truck, or other means to access the actual installation locations. 8. Connect power to the HotPort node and peripherals. Preparing Earth Ground The HotPort node must be properly connected to earth ground. Failure to do so may result in equipment damage, injury, or death. The product warranty does not cover damages resulting in part or in whole from improper grounding. Consult your location’s building and electrical codes regarding antennas and follow them, or consult the National Electric Code (NEC). • If connecting to a tower or pole, connect the base of the tower pole directly to the building’s ground or to one or more approved grounding rods using 10 AWG ground wire and corrosion-resistant connectors. • Connect the grounding cable to rain gutters only if the rain gutter is connected to earth ground. • Ground rods should be copper-plated, 1.8 - 2.4 m (6 - 8 ft) long. • Install all grounding components in straight lines. If bends are unavoidable, do not make sharp turns. • Earth-to-ground should not be more than 10 ohms. • Understanding the soil is very important in order to create a proper earth ground. If your soil is rocky or sandy, drive your ground rods and then pull them back out and dump an approved ground enhancement material into the holes where the grounding rods go. Then replace the grounding rods. Keep in mind that some salt compounds are corrosive and can cause copper to corrode. Safety Considerations Consider the following safety issues. • Use approved, non-conducting ladders. • If mounting to a pole or tower, make sure all poles and towers are securely grounded. • Use approved and non-conducting shoes and other safety equipment. Make sure that all equipment is in good repair. • Make sure antennas are DC grounded; if not, cables must have lightning arrestors. January 2010 Firetide Instant Mesh Networks 7 Antenna Placement Firetide recommends the use of antennas specifically designed for MIMO applications. While it is possible to select and mount six individual antennas, determining correct placement and spacing is difficult. Use an antenna engineered for best results with MIMO. If you are not using three antennas on each radio, install antennas in order, from the front of the unit toward the back. Do not ‘skip’ antenna connections. Mounting Outdoor Antennas Once you determine which RF band to use, you can order spectrumspecific high-gain antennas from Firetide or another supplier. Many installers prefer to mount the HotPort node and its associated antennas to a short bar, typically about 2 meters long. This entire bar assembly is them mounted horizontally to the vertical mast of the main antenna structure. Mounting Guidelines • It is often easier to install all devices onto a pole, and then attach the pole to the roof. In many cases, connecting the devices to a pole already attached to the roof top can be difficult and dangerous. • A lightning surge suppressor must be used. Some antennas include one. If not, install a lightning surge suppressor. • Locate the HotPort close to the antenna; a short antenna cable gives better performance than a longer one. Firetide recommends antenna cables less than 3 meters. • The HotPort node and its antenna must both be grounded. • Large or heavy antennas must be mounted to a pole or other secure structure. • The antennas should not be within 1 meter (~3 ft.) of any metal bar or structure, and ideally not within 1 meter (~3 ft.) of any concrete or stone structure. In general, try to locate the antennas as far from such objects as practicable. • Shorter antenna cables give better performance. Plan your installation to minimize antenna cable length. However, do not attempt to splice or shorten the antenna cable. • If a longer coax cable is required, the system requires a highquality, low-loss 50 ohm cable. Contact your local distributor to obtain a 50 ohm cable with the correct connectors. Firetide recommends LMR400 cable or better. • Minimize use of connectors and adapters. • Once you’ve verified that everything is working, waterproof all connections! • Do not mount the antenna pole near power lines. • When mounting next to an access point, mount the access point lower on the pole and at least 1 meter (~3 ft.) from the antennas. You can also mount the access point on a horizontal bar to achieve the required separation. Mounting Bracket Your HotPort node shipped with a two-piece mounting bracket. The inner bracket can be left attached to the node, as shown This bracket is of the same design as the HotPort 6202 outdoor below. bracket, so you can install a 7200 in place of a 6201 or 6202. The assembly is shown below. To mount the node, remove the outer piece, by loosening the thumb screws. HotPort Series 7000 Mesh Nodes January 2010 Mounting the Universal Bracket You can mount the node to a wall, a light pole, or an irregularly shaped pole. The universal mounting bracket has been designed with multiple holes and slots to allow mounting with bolts, straps, or other methods. Extra nuts and bolts are provided for this purpose; don’t be alarmed if you have leftover fasteners when installation is complete. Universal Mounting Bracket Attached to Pole Wall Mounting The Universal Mounting Bracket contains holes and slots to allow it to be mounted via U-bolts or straps. Use four screws (not supplied) to attach the universal mounting bracket securely to the wall using the four holes near the top and bottom of the universal mounting bracket. Use appropriate anchors when attaching to masonry or other materials. This shows the use of spacer nuts when mounting to smaller poles. You may find an open-end wrench useful for tightening the inner 1. Insert the two U-bolts through the holes in the claw-toothed nuts in these applications. pole-gripper piece. Pole Mounting 2. On each U-bolt, place a washer, a lock washer, and a nut. Smaller pole diameters usually require a second nut as a spacer to hold the bracket away from the U-bolt clamp. Fingertighten the nuts. There should be about 12-15 mm (1/2-5/8”) of U-bolt sticking past the second nut. U-bolt Mounted on Pole Mounting Bracket Showing Use of Spacer Nuts Using Mounting Straps For poles with diameters larger than 50 mm (2”), irregularly Mount the second U-bolt. Use the mounting bracket as a guide to shaped poles, or light poles, you can use mounting straps (not correctly space the two U-bolts, then tighten the nuts. A horizonsupplied) to mount the HotPort enclosure. tal pole-mount is also shown for reference. 1. Position the universal mounting bracket against the pole. 2. Thread two mounting straps around the pole and through the slots located near the top and bottom of the universal mounting bracket. Secure the mounting straps. 3. Attach the enclosure to the universal mounting bracket by sliding the metal clips on the back of the enclosure into the metal straps on the universal mounting bracket. U-bolts, Vertical and Horizontal Mounting Secure the enclosure to the universal mounting bracket using the four captive screws on the sides of the universal mounting bracket. Mounting Antennas Use lock washers and nuts to secure the bracket to the U-bolts. Now that you’ve attached the Universal Mounting Plate, you are Installation on a horizontal pole is the same, you just use differ- ready to proceed to the next steps. Most outdoor applications use separately-mounted antennas, if so, mount your antennas now. If ent holes in the mounting plate. you are using the temporary staging antennas, the next step is to attach the HotPort node itself. January 2010 Firetide Instant Mesh Networks 9 Connecting Cables After your node is mounted, attach the six antennas, the power cable, and any Ethernet cables you need. Note that all of the weatherproof caps have been removed from the node for illustrative purposes. You should not leave any unused connector uncovered. Figure 5. HotPort 7200 Bottom Panel ac power dc power power port 3 status port 2 radio 1 radio 2 –mesh– port 1 usb ethernet Note the locations of the reset button under the weatherproof cap. To reset the unit, apply power and wait until the unit has fully booted and the status light has come on. Then use a paperclip to press and hold the reset button until the status LED blinks. Power Connection Connect the suppled AC power cable to AC power and to the HotPort node. If you wish to power your node with DC power, you will need a source of power which can deliver 12 V ±10% at 3 A. Information on building custom power cables is shown in Appendix B. Do not connect both AC and DC supplies simultaneously. Powering Other Ethernet Devices Ports 2 and 3 on a Series 7200 node can provide Power over Ethernet (PoE) functionality to Powered Devices (PD) connected to these ports. (Port 1 cannot.) A Powered Device can receive data and the power to process the data from the HotPort node, which functions as Power Sourcing Equipment (PSE) in this configuration. To receive power from a HotPort node, the device must support the IEEE 802.3af standard, which defines PoE functionality. Connecting Antennas Don’t forget to order your permanent outdoor antennas! You can’t use the staging antennas outdoors, they might fail. When connecting antennas, connect them in numerical order 1-2-3. If you are not using three antennas per radio, do not ‘skip’ antenna connectors. The antenna 1 connector is at the top of the unit (farthest from the power and Ethernet connections) on both the left and right side. radio 2 radio 1 antenna 1 10 antenna 2 HotPort Series 7000 Mesh Nodes antenna 3 antenna 3 antenna 2 antenna 1 January 2010 Appendix A - Contacting Firetide Dealer-Provided Technical Support and Warranty Service Sales Assistance If you need additional technical assistance, please contact your Firetide dealer directly. All authorized Firetide dealers are trained and authorized to provide technical support and warranty services for our products and have qualified technical staff available to help you build and maintain your Firetide mesh network. If you need additional HotPort wireless mesh nodes or accessories, please contact your Firetide dealer directly. If you do not know your dealer’s name, simply email sales@firetide.com and we will send you the dealer information you need. To help us provide the best service possible, be sure to include your phone number, address, and the serial numbers of the HotPort nodes at your location. Firetide-Provided Technical Support You can also get technical support from Firetide. Simply email support@firetide.com, or call 1-877-FIRETIDE, extension 2, or +1 408 399 7771. Product Returns Mailing Address Firetide, Inc. 140 Knowles Drive Los Gatos, CA 95032 USA Please contact your Firetide dealer for instructions on returning defective or damaged products for repair or replacement. Do not return products to Firetide, Inc. Please keep all original packaging materials in the event they are needed to return the product for servicing. January 2010 Firetide Instant Mesh Networks 11 Appendix B - Connector Wiring HotPort Outdoor Node AC Power Connector Figure 6 shows the pinout of the AC Power connector used on Series 7200 outdoor nodes. Views are shown of both the connector on the unit, and the mating connector on the cable itself. Pin 1 is neutral; pin 2 is line, and pin 3 is ground. Figure 6. Series 7200 AC Power Connector 3-ground 3-ground 2-line 1-neutral 1-neutral 2-line Series 6200 AC Power Connector View Series 6200 AC Power Cable-End View HotPort Outdoor Node DC Power Connector Figure 7 shows the pinout of the power connector used to supply power to Series 7200 nodes. Each view is of the cable connector, as viewed end-on. Pin 4 is +12VDC power. Pin 3 is ground. Figure 7. Series 7200 DC Power Connector Series 6200 DC Power Connector 3 ------- ground ------- 3 4 --- power --- 4 Cable-End View Connector View Custom Power Cables Firetide offers an accessory DC power cable. The part number is 3200-2401, and this cable can be used to connect other DC sources to your Series 7200 node. One end of the cable has the six-pin connector used by the Series 7200; the other end has a weatherproof 4-pin connector. Both connectors are of the LTZ type. The cable is wired as shown in Figure 8. Custom cables can be built in either of two ways. 1. You can obtain a 4-pin female LTZ connector and build an adapter cable. 2. You can cut the 4-pin male LTZ connector off the cable and attach whatever type of connector you require. Figure 8. DC Power Adapter Cable Wiring Pin 1 4-pin LTZ Connector Pin 2 Pin 3 blue positive-lead power (nominal +15 volts) Pin 4 black ground/drain Pin 4 Series 6200 DC Power Connector brown white Pin 3 3 ------- ground 4 ---- power Cable-End View DC power to a HotPort node must be 12 VDC ±15%, at 3A. Series 7200 nodes can provide PoE-compliant 48 VDC power to other devices. 12 HotPort Series 7000 Mesh Nodes January 2010 Appendix C - Specifications Common Specifications Supported Data Rates & Standards • 802.11a Wireless Interface These tables describes the technical limits of the nodes. Various country restrictions may further limit available choices. Model 7100 7200 Use Indoor, Worldwide, 2.4, 4.9, 5 GHz Outdoor, Worldwide, 2.4, 4.9, 5 GHz Single-radio HotPort 7100 nodes appear as 7101. Dual-radio HotPort 7100 nodes appear as 7102. Single-radio HotPort 7200 nodes appear as 7201. Dual-radio HotPort 7200 nodes appear as 7202. For all models: Bands (GHz) Frequency (GHz) 802.11a 5.15-5.25 802.11n Restrictions 5.725-5.825 4.9-5.090 Japan only 4.94-4.990 5.470-5.725 US Public Safety ETSI 301.893, U-NII 2.412-2.484 802.11n • 802.11b 1/2/5.5/11Mbps • 802.11g 6/9/12/18/24/36/48/54Mbps • 802.11n 6.5/13/19.5/26/65/130/195/260 (1) 7.2/14.4/21.7/28.9/72.2/144/216.7/288.9 (2) 13.5/27/40.5/54/135/270 (3) 15/30/45/60/150/300 (4) (1) 20MHz LGB (2) 20MHz SGB (3) 40MHz LGB (4) 40MHz LGB • Network Standards: IEEE 802.11a/b/d/g/e/f/h/i/n • Dynamic Frequency Selection (DFS) capable in conjunction with Firetide Software application • Firetide AutoMesh Protocol Mesh Management Software • HotView Pro™ mesh management software Security & Encryption Bands (GHz) Max TX Power 802.11a 26dBm 5.725-5.825 UNII-3 26dBm 802.11n 24dBm 23dBm • 802.11a Capable of switching to 1⁄4 and 1⁄2 rates for 4.940 – 4.990 GHz Public Safety Band Mesh Protocol 5.25-5.35 802.11b/g No. of Radios 1 or 2 1 or 2 6/9/12/18/24/36/48/54Mbps 5.470-5.735 UNII 5.25-5.36 M UNII-2 5.15-5.25 UNII-1 23 dBm 23 dBm 802.11b 17 dBm 24 dBm 802.11g 26dBm 802.11n 26dBm January 2010 • Security: WPA—64/128/256 w/TKIP, AES, Antennas • Twelve detachable omnidirectional, vertical polarization, six for each band. Regulatory Agency Certifications • Contact your Firetide dealer for product availability and certifications for your country. Firetide Instant Mesh Networks 13 Series 7200 Outdoor Unit Specifications Series 7100 Indoor Unit Specifications Network Ports Network Ports • Three 10/100/1000 Mbps Ethernet ports with weatherproof connectors, LED activity indicator • IEEE 802.3, 802.3u compliant • CSMA/CD 10/100/1000 autosense • Ports 2, 3 PSE Power over Ethernet per 802.3at Enclosure • Cast aluminum NEMA-4X/IP66 enclosure • Six N-type antenna connectors • Two weatherproof power connectors (AC and DC) • Three weatherproof Ethernet connectors • System LEDs (power, status, mesh (per radio), ethernet) • Weight: 12 lbs (5.5 Kg) with bracket • Dimensions: 8.8” x 11.2” x 4” (220 x 280 x 100 mm) Power • AC Input: 90-240 VAC, 50-60 Hz, 0.9A • DC Input: 12 VDC ±15%, 3 A • Port 2: IEEE 802.3af compliant PoE (PSE), 13.5 W max • Port 3: IEEE 802.3af compliant PoE (PSE), 13.5 W max Environmental Specifications • Operating temperature: -40º C to +60ºC • Storage temperature: -40º C to +85º C • Humidity (non-condensing): 10% to 90% • Storage humidity (non-condensing): 5% to 95% • Maximum altitude 15,000 feet (4600 meters) • Four 10/100/1000 Mbps Ethernet ports with LEDs • PoE PD on Port 1 • IEEE 802.3, 802.3u compliant • CSMA/CD 10/100/1000 autosense Enclosure • Plenum-rated metal enclosure • Six RP-SMA antenna connectors • One DC power connector • Four Ethernet connectors • System indicator LEDs: power, status, per-radio mesh, ethernet • Weight: 3 lbs (1.4 Kg) • Dimensions: 9.4” x 6” x 1.8” (238 x 152 x 48 mm) Power • DC Input: 12 VDC ±15%, 3 A Environmental Specifications • Operating temperature: 0º C to +60ºC • Storage temperature: -20º C to +70º C • Humidity (non-condensing): 10% to 90% • Storage humidity (non-condensing): 5% to 95% • Maximum altitude 15,000 feet (4600 meters) Included Accessories • AC power adapter • Six 2.4 GHz and six 4.9-5.8 GHz 5 dBi omni staging antennas, for indoor use only. Included Accessories • Bracket for pole and wall mounting • External power cord • Six 2.4 GHz and six 4.9-5.8 GHz 5 dBi omni staging antennas, for indoor and temporary use only. The 7200 has been certified with a 9 dBi omni, 16 dBi sector, and 19 dBi panel outdoor antenna. Contact Firetide for part numbers and ordering information. 14 HotPort Series 7000 Mesh Nodes January 2010 Appendix D - Regulatory Notices USA FCC Radiation Exposure Statement To ensure compliance with the FCC’s RF exposure limits, the antenna used for this transmitter must be installed to provide a This device complies with Part 15 of the FCC Rules. Operation is separation distance from all persons. subject to the following two conditions: • For the 7100, the distance must be 20 cm. • This device may not cause harmful interference. • For the 7200, the distance must be 76 cm. • This device must accept any interference received, including The 7100 and 7200 must not be co-located or operated in coninterference that may cause undesired operation. junction with any other antenna or transmitter. Installers and end users must follow these installation instructions. FCC Part 15 Note FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in an office installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. Installation Antenna(s) for this unit must be installed by a qualified professional. Operation of the unit with non-approved antennas is a violation of U.S. FCC Rules, Part 15.203(c), Code of Federal Regulations, Title 47. Canadian Compliance Statement This Class A Digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe A respecte les exigences du Reglement sur le material broilleur du Canada. This device complies with Class A Limits of Industry Canada. Operation is subject to the following two conditions: • Connect the equipment into an outlet on a circuit different 1. This device may not cause harmful interference, and from that to which the receiver is connected. 2. This device must accept any interference received, including • Consult the dealer or an experienced radio/television techni- interference that may cause undesired operation. cian for help. Firetide HotPoint 7100 and 7200 wireless mesh nodes are certified to the requirements of RSS-210 for 2.4 and 5 GHz spread spectrum devices. The use of this device in a system operating either This equipment has been tested pursuant to FCC Part 90, DSRC-C partially or completely outdoors may require the user to obtain a mask certification, and is approved for use in the US on Public license for the system according to the Canadian regulations. For Safety bands by licensed Public Safety agencies. further information, contact your local Industry Canada office. FCC Part 90 Note Public Safety Band Canadian units will not transmit in the 5600-5650 MHz band. Pursuant to Part 90.1215, use of antennas with gain greater than 9 dBi and up to 19 dBi in the 4.940 - 4.990 GHz Public Safety band is permissible without reduction of TX output power. The antenna shall have a directional gain pattern in order to meet the requirement of point to point and point to multi-point operation. Modifications Any modifications made to this device that are not approved by Firetide, Inc. may void the authority granted to the user by the FCC to operate this equipment. January 2010 Firetide Instant Mesh Networks 15 Firetide, Inc. 140 Knowles Drive Los Gatos, CA 95032
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 4.2.2-c063 53.352624, 2008/07/30-18:05:41 Create Date : 2010:01:07 12:42:21-08:00 Metadata Date : 2010:01:07 12:42:29-08:00 Modify Date : 2010:01:07 12:42:29-08:00 Creator Tool : Adobe InDesign CS4 (6.0.4) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 9628 bytes, use -b option to extract) Instance ID : uuid:f20fddba-fd65-9246-97f4-08d18c4cebd5 Document ID : xmp.did:D9040EE21C20681197A59DD54EE0A9C9 Original Document ID : adobe:docid:indd:37a099f0-f9c0-11dd-aa72-f3d39728dbbb Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:D8040EE21C20681197A59DD54EE0A9C9 Derived From Document ID : xmp.did:028011740720681197A59DD54EE0A9C9 Derived From Original Document ID: adobe:docid:indd:37a099f0-f9c0-11dd-aa72-f3d39728dbbb Derived From Rendition Class : default History Action : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:ED7F117407206811B34BFCE4DCB8903B, xmp.iid:EE7F117407206811B34BFCE4DCB8903B, xmp.iid:EF7F117407206811B34BFCE4DCB8903B, xmp.iid:F07F117407206811B34BFCE4DCB8903B, xmp.iid:F17F117407206811B34BFCE4DCB8903B, xmp.iid:F27F117407206811B34BFCE4DCB8903B, xmp.iid:F37F117407206811B34BFCE4DCB8903B, xmp.iid:F47F117407206811B34BFCE4DCB8903B, xmp.iid:F57F117407206811B34BFCE4DCB8903B, xmp.iid:F67F117407206811B34BFCE4DCB8903B, xmp.iid:08B89C850C206811B34BFCE4DCB8903B, xmp.iid:09B89C850C206811B34BFCE4DCB8903B, xmp.iid:0AB89C850C206811B34BFCE4DCB8903B, xmp.iid:0BB89C850C206811B34BFCE4DCB8903B, xmp.iid:9D061EF21B206811B34BFCE4DCB8903B, xmp.iid:4791B99729206811B34BFCE4DCB8903B, xmp.iid:4891B99729206811B34BFCE4DCB8903B, xmp.iid:4991B99729206811B34BFCE4DCB8903B, xmp.iid:4A91B99729206811B34BFCE4DCB8903B, xmp.iid:F77F1174072068119109A7BD3A8ADC66, xmp.iid:F87F1174072068119109A7BD3A8ADC66, xmp.iid:F97F1174072068119109A7BD3A8ADC66, xmp.iid:FA7F1174072068119109A7BD3A8ADC66, xmp.iid:FB7F1174072068119109A7BD3A8ADC66, xmp.iid:FC7F1174072068119109A7BD3A8ADC66, xmp.iid:FD7F1174072068119109A7BD3A8ADC66, xmp.iid:FE7F1174072068119109A7BD3A8ADC66, xmp.iid:FF7F1174072068119109A7BD3A8ADC66, xmp.iid:00801174072068119109A7BD3A8ADC66, xmp.iid:90A49C230E2068119109A7BD3A8ADC66, xmp.iid:91A49C230E2068119109A7BD3A8ADC66, xmp.iid:92A49C230E2068119109A7BD3A8ADC66, xmp.iid:93A49C230E2068119109A7BD3A8ADC66, xmp.iid:94A49C230E2068119109A7BD3A8ADC66, xmp.iid:95A49C230E2068119109A7BD3A8ADC66, xmp.iid:96A49C230E2068119109A7BD3A8ADC66, xmp.iid:97A49C230E2068119109A7BD3A8ADC66, xmp.iid:98A49C230E2068119109A7BD3A8ADC66, xmp.iid:99A49C230E2068119109A7BD3A8ADC66, xmp.iid:9AA49C230E2068119109A7BD3A8ADC66, xmp.iid:C4F67BA21A2068119109A7BD3A8ADC66, xmp.iid:C5F67BA21A2068119109A7BD3A8ADC66, xmp.iid:C6F67BA21A2068119109A7BD3A8ADC66, xmp.iid:C7F67BA21A2068119109A7BD3A8ADC66, xmp.iid:C8F67BA21A2068119109A7BD3A8ADC66, xmp.iid:CFA2E3CE702068119457EE89CBA16AD0, xmp.iid:D0A2E3CE702068119457EE89CBA16AD0, xmp.iid:D1A2E3CE702068119457EE89CBA16AD0, xmp.iid:D2A2E3CE702068119457EE89CBA16AD0, xmp.iid:D3A2E3CE702068119457EE89CBA16AD0, xmp.iid:F77F1174072068118F62DF08E6AF9C04, xmp.iid:F87F1174072068118F62DF08E6AF9C04, xmp.iid:F97F1174072068118F62DF08E6AF9C04, xmp.iid:FA7F1174072068118F62DF08E6AF9C04, xmp.iid:FB7F1174072068118F62DF08E6AF9C04, xmp.iid:FD7F117407206811B481932CF08869F6, xmp.iid:FE7F117407206811B481932CF08869F6, xmp.iid:018011740720681197A59DD54EE0A9C9, xmp.iid:028011740720681197A59DD54EE0A9C9, xmp.iid:038011740720681197A59DD54EE0A9C9, xmp.iid:048011740720681197A59DD54EE0A9C9, xmp.iid:058011740720681197A59DD54EE0A9C9, xmp.iid:068011740720681197A59DD54EE0A9C9, xmp.iid:078011740720681197A59DD54EE0A9C9, xmp.iid:088011740720681197A59DD54EE0A9C9, xmp.iid:098011740720681197A59DD54EE0A9C9, xmp.iid:0A8011740720681197A59DD54EE0A9C9, xmp.iid:D8040EE21C20681197A59DD54EE0A9C9, xmp.iid:D9040EE21C20681197A59DD54EE0A9C9 History When : 2009:07:30 14:22:54-07:00, 2009:07:30 14:22:54-07:00, 2009:07:30 14:25:10-07:00, 2009:07:30 14:46:43-07:00, 2009:07:30 14:47:13-07:00, 2009:07:30 14:52:54-07:00, 2009:07:30 14:53:22-07:00, 2009:07:30 14:54:13-07:00, 2009:07:30 14:56:56-07:00, 2009:07:30 14:58:50-07:00, 2009:07:30 14:59:10-07:00, 2009:07:30 14:59:19-07:00, 2009:07:30 15:01:58-07:00, 2009:07:30 15:02:25-07:00, 2009:07:30 17:22:58-07:00, 2009:07:30 18:58:17-07:00, 2009:07:30 18:58:29-07:00, 2009:07:30 18:59:25-07:00, 2009:07:30 19:03:31-07:00, 2009:07:31 08:21:27-07:00, 2009:07:31 08:23:10-07:00, 2009:07:31 08:38:17-07:00, 2009:07:31 08:38:43-07:00, 2009:07:31 08:40:48-07:00, 2009:07:31 08:41:54-07:00, 2009:07:31 08:45:06-07:00, 2009:07:31 08:54:33-07:00, 2009:07:31 08:59:26-07:00, 2009:07:31 09:03:16-07:00, 2009:07:31 09:09:19-07:00, 2009:07:31 09:12:35-07:00, 2009:07:31 09:18:15-07:00, 2009:07:31 09:19:05-07:00, 2009:07:31 09:19:40-07:00, 2009:07:31 09:24:06-07:00, 2009:07:31 09:39:03-07:00, 2009:07:31 09:39:21-07:00, 2009:07:31 09:40:12-07:00, 2009:07:31 09:41:16-07:00, 2009:07:31 09:42:05-07:00, 2009:07:31 10:38:45-07:00, 2009:07:31 10:57:21-07:00, 2009:07:31 11:00:53-07:00, 2009:07:31 11:01:35-07:00, 2009:07:31 11:05:38-07:00, 2009:08:02 07:18:42-07:00, 2009:08:02 07:20:51-07:00, 2009:08:02 07:23:40-07:00, 2009:08:02 07:38:52-07:00, 2009:08:02 07:40:06-07:00, 2009:08:03 17:30:11-07:00, 2009:08:03 17:31:43-07:00, 2009:08:03 17:34:23-07:00, 2009:08:03 17:36:09-07:00, 2009:08:03 17:37:35-07:00, 2009:08:04 15:07:45-07:00, 2009:08:04 15:08:32-07:00, 2010:01:07 09:52:28-08:00, 2010:01:07 09:52:28-08:00, 2010:01:07 09:53:53-08:00, 2010:01:07 10:48-08:00, 2010:01:07 10:52:30-08:00, 2010:01:07 10:54:03-08:00, 2010:01:07 10:57:23-08:00, 2010:01:07 11:00:17-08:00, 2010:01:07 11:03:03-08:00, 2010:01:07 11:03:48-08:00, 2010:01:07 12:41:57-08:00, 2010:01:07 12:41:57-08:00 History Software Agent : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0 History Changed : /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /;/metadata, /, /, /, /, /, /, /, /, /metadata, /;/metadata Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream Manifest Placed X Resolution : 72.00, 72.00, 72.00, 600.00, 600.00, 600.00, 600.00, 600.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Y Resolution : 72.00, 72.00, 72.00, 600.00, 600.00, 600.00, 600.00, 600.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00 Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches Manifest Reference Instance ID : uuid:b9392b94-75ca-534c-9f07-ec50860debb3, uuid:4ac72fb0-2481-ce4e-9612-819b41a2b73e, uuid:4ac72fb0-2481-ce4e-9612-819b41a2b73e, uuid:7B3B7697DD3B11DB93B884F0724E0D1B, uuid:7B3B769FDD3B11DB93B884F0724E0D1B, uuid:7501649F096DDC11B04FCD96EA3864E4, uuid:B98EDC6DC8F111DB8FE0EE2B432BE2A4, uuid:EB21ADD8DD3B11DB93B884F0724E0D1B, uuid:dd74926c-cc5a-5746-b3aa-07bc19410155, uuid:1bbed826-0298-fe4b-9c45-9b4aa1932386, uuid:cd34c8d0-6a02-974f-b66d-61217524b5b1, uuid:b889a1fe-ea16-11db-bbea-000a958e60a8, uuid:f7e73746-ea1c-11db-bbea-000a958e60a8, uuid:112639f3-2ec7-b941-b0e1-2efdaa26052f, uuid:b9392b94-75ca-534c-9f07-ec50860debb3 Manifest Reference Document ID : uuid:AEB1C89BDFC511DBA350E08D6C633A70, xmp.did:F77F117407206811A7918BE20EE67768, xmp.did:F77F117407206811A7918BE20EE67768, uuid:F88D649DCAD8DB118DEF8F99FE6474BA, uuid:BA36FB83E7D8DB118DEF8F99FE6474BA, uuid:083C48FBB7D8DB118DEF8F99FE6474BA, uuid:B98EDC6CC8F111DB8FE0EE2B432BE2A4, uuid:E7BECF4CC0D8DB118DEF8F99FE6474BA, xmp.did:018011740720681194578165994E99FE, xmp.did:028011740720681194578165994E99FE, xmp.did:038011740720681194578165994E99FE, uuid:2552B978CA4E11DBBBB8D4FD789DF739, uuid:2552B97BCA4E11DBBBB8D4FD789DF739, uuid:0F13725D8ECB11DB9C7BCA4243CC80C7, uuid:AEB1C89BDFC511DBA350E08D6C633A70 Doc Change Count : 2836 Format : application/pdf Producer : Adobe PDF Library 9.0 Trapped : False Page Count : 16 Creator : Adobe InDesign CS4 (6.0.4)EXIF Metadata provided by EXIF.tools