First Alert Sa87Cn Users Manual M08_0020_002_E(SA87CN/SA97CN)

SA87CN to the manual 885b4bd1-e72b-41a2-a062-7ffd057712e3

2015-01-23

: First-Alert First-Alert-Sa87Cn-Users-Manual-231842 first-alert-sa87cn-users-manual-231842 first-alert pdf

Open the PDF directly: View PDF .
Page Count: 6

IMPORTANT!

PLEASE READ CAREFULLY AND SAVE.

This user’s manual contains important information about your Smoke

Alarm’s operation. If you are installing this Smoke Alarm for use by

others, you must leave this manual—or a copy of it—with the end user.

USER’S MANUAL

Printed in Mexico

M08-0020-002 J1 07/04 Model SA87B, SA97B

SMOKE ALARM WITH

SILENCE FEATURE

SMOKE ALARM WITH

SILENCE FEATURE AND

LONG-LIFE LITHIUM POWER

TABLE OF CONTENTS

Fire Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before You Install This Smoke Alarm . . . . . . . . . . . . . . . . . . . . . . .1

How To Install This Smoke Alarm . . . . . . . . . . . . . . . . . . . . . . . . . .2

Weekly Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Regular Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

If This Smoke Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

What To Do In Case Of Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Using the Silence Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

If You Suspect A Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Recommended Locations For Smoke Alarms . . . . . . . . . . . . . . .4-5

Locations To Avoid For Smoke Alarms . . . . . . . . . . . . . . . . . . . . . .5

About Smoke Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Special Compliance Considerations . . . . . . . . . . . . . . . . . . . . . . . .6

Limitations Of Smoke Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

BRK Brands, Inc., 3901 Liberty Street Road, Aurora, IL 60504-8122

Consumer Affairs: (800) 323-9005 • www.firstalert.com

FIRE SAFETY TIPS

Follow safety rules and prevent hazardous situations: 1) Use smoking

materials properly. Never smoke in bed. 2) Keep matches or lighters

away from children; 3) Store flammable materials in proper containers;

4) Keep electrical appliances in good condition and don’t overload elec-

trical circuits; 5) Keep stoves, barbecue grills, fireplaces and chimneys

grease- and debris-free; 6) Never leave anything cooking on the stove

unattended; 7) Keep portable heaters and open flames, like candles,

away from flammable materials; 8) Don’t let rubbish accumulate.

Keep alarms clean, and test them weekly. Replace alarms immediately if

they are not working properly. Smoke Alarms that do not work cannot alert

you to a fire. Keep at least one working fire extinguisher on every floor, and

an additional one in the kitchen. Have fire escape ladders or other reliable

means of escape from an upper floor in case stairs are blocked.

*All First Alert®Smoke Alarms conform to regulatory requirements,

including UL217 and are designed to detect particles of combustion.

Smoke particles of varying number and size are produced in all fires.

Ionization technology is generally more sensitive than photoelectric

technology at detecting small particles, which tend to be produced

in greater amounts by flaming fires, which consume combustible

materials rapidly and spread quickly. Sources of these fires may include

paper burning in a wastebasket, or a grease fire in the kitchen.

Photoelectric technology is generally more sensitive than ionization

technology at detecting large particles, which tend to be produced

in greater amounts by smoldering fires, which may smolder for

hours before bursting into flame. Sources of these fires may include cig-

arettes burning in couches or bedding.

For maximum protection, use both types of Smoke Alarms on each

level and in every bedroom of your home.

SMOKE AND FIRE* ALARM

•This unit will not alert hearing impaired residents. It is recom-

mended that you install special units which use devices like

flashing strobe lights to alert hearing impaired residents.

•Do not connect this unit to any other alarm or auxiliary device. It

is a single-station unit that cannot be linked to other devices.

Connecting anything else to this unit may prevent it from working

properly.

•Unit will not operate without battery power. The Smoke Alarm

cannot work until you install the battery in the correct position

(Match “+” to “+” and “-” to “-”).

•This Smoke Alarm has a battery guard which prevents it from

closing unless a battery is installed. This warns you the unit will

not operate without a battery.

•Do not install this unit over an electrical junction box. Air cur-

rents around junction boxes can prevent smoke from reaching

the sensing chamber and prevent the unit from alarming. Only

AC powered units are intended for installation over junction

boxes.

•Do not stand too close to the unit when the alarm is sounding. It

is loud to wake you in an emergency. Exposure to the horn at

close range may harm your hearing.

•Do not paint over the unit. Paint may clog the openings to the

sensing chamber and prevent the unit from operating properly

BEFORE YOU INSTALL THIS SMOKE ALARM

IMPORTANT! Read “Recommended Locations for Smoke Alarms” and

“Locations to Avoid for Smoke Alarms” before beginning. This unit

monitors the air, and when smoke reaches its sensing chamber, it

alarms. It can give you more time to escape before fire spreads. This

unit can ONLY give an early warning of developing fires if it is installed,

maintained and located where smoke can reach it, and where all resi-

dents can hear it, as described in this manual. This unit will not sense

gas, heat, or flame. It cannot prevent or extinguish fires.

Understand The Different Type of Smoke Alarms

Battery powered or electrical? Different Smoke Alarms provide

different types of protection. See “About Smoke Alarms” for details.

Know Where To Install Your Smoke Alarms

Fire Safety Professionals recommend at least one Smoke Alarm on

every level of your home, in every bedroom, and in every bedroom hall-

way or separate sleeping area. See “Recommended Locations For

Smoke Alarms” and “Locations To Avoid For Smoke Alarms” for details.

Know What Smoke Alarms Can and Can’t Do

A Smoke Alarm can help alert you to fire, giving you precious time to

escape. It can only sound an alarm once smoke reaches the sensor.

See “Limitations of Smoke Alarms” for details.

Check Your Local Building Codes

This Smoke Alarm is designed to be used in a typical single-family

home. It alone will not meet requirements for boarding houses, apart-

ment buildings, hotels or motels. See “Special Compliance

Considerations”

for details.

HOW TO INSTALL THIS SMOKE ALARM

THE PARTS OF THIS SMOKE ALARM

FOLLOW THESE SIMPLE STEPS!

1. “OPEN HERE”tab

2. Cover hinge

3. Test button,

power/alarm indicator

4. Silence button

1. “OPEN HERE”tab

2. Test button, power/alarm

indicator

3. Silence button

4. Smoke Alarm base

5. Mounting slots

6. DO NOT install any

battery here!

7. Install 9V battery here

This unit is designed to be mounted on the

ceiling, or on the wall if necessary.

Tools you will need:

• Pencil

• Drill with 3/16” (5 mm) drill bit

• Standard/Flathead screwdriver

• Hammer

1. Hold base firmly and pull up on cover tab

marked “OPEN HERE.” This will open the

hinged cover. The cover may unsnap from

the base if it's opened too far. This will not

damage the unit—the cover hinge snaps

back into place easily.

2. Hold the Smoke Alarm base against the

ceiling (or wall) and make a mark at the

center of each of the mounting slots with

a pencil.

3. Put the unit where it won’t get covered

with dust when you drill the mounting

holes.

4. Using a 3/16” (5 mm) drill bit, drill a hole

through each pencil mark.

5. Insert the plastic screw anchors (in the

plastic bag with screws) into the holes.

Tap the screw anchors gently with a ham-

mer, if necessary, until they are flush with

the ceiling or wall.

6. Tighten the screws (provided) into the

screw anchors, then loosen them two

turns.

7. Fit the Smoke Alarm over the screw heads

as shown. Close cover.

8. If the Smoke Alarm cover does not line up

the way you want it, rotate the base and

re-tighten the screws.

9. Activate the battery. With the cover open,

remove and reinstall the battery so the ter-

minals on the battery match the terminals

on the Smoke Alarm. Match “+” to “+” and

“-” to “-.” Push the battery in until it snaps

in securely and cannot be shaken loose.

If the battery is not snapped in completely,

the unit cannot receive battery power. The

Smoke Alarm may beep briefly when you

install the battery—this is normal.

Once the battery is installed, the power

indicator light (behind the test button) will

flash once a minute to show you the

Smoke Alarm is working.

10. Close the cover all the way.

11. Test the Smoke Alarm. See “Weekly

Testing.”

WEEKLY TESTING

•NEVER use an open flame of any kind to test this unit. You

might accidentally damage or set fire to the unit or to your

home. The built-in test switch accurately tests the unit’s opera-

tion as required by Underwriters Laboratories, Inc. (UL). If you

choose to use an aerosol smoke product to test the Smoke

Alarm, be certain to use one that has been Listed to

Underwriters Laboratories, Inc. Safety Standards, and use it

only as directed. Use of non-UL Listed products or improper use

of UL Listed products may affect the Smoke Alarm’s sensitivity,

and may void your warranty.

•If the Alarm ever fails to test properly, replace it immediately.

Products under warranty may be returned to the manufacturer

for replacement. See “Limited Warranty” for details.

•DO NOT stand close to the alarm when the horn is sounding.

Exposure at close range may be harmful to your hearing. When

testing, step away when horn starts sounding.

It is important to test this unit every week to make sure it is work-

ing properly. Using the test button is the recommended way to test this

Smoke Alarm. During testing, you will hear a loud, repeating horn pat-

tern: 3 beeps, pause, 3 beeps, pause.

IF THIS SMOKE ALARM SOUNDS

RESPONDING TO AN ALARM

During an alarm, you will hear a loud, repeating horn pattern:

3 beeps, pause, 3 beeps, pause.

•If the unit alarms and you are not testing the unit, it is warning

you of a potentially dangerous situation that requires your

immediate attention. NEVER ignore any alarm. Ignoring the

alarm may result in injury or death.

•Never remove the batteries from a battery operated Smoke

Alarm to stop an unwanted alarm (caused by cooking smoke,

etc.). Removing batteries disables the alarm so it cannot sense

smoke, and removes your protection. Instead open a window

or fan the smoke away from the unit. The alarm will reset

automatically.

•If the unit alarms get everyone out of the house immediately.

WHAT TO DO IN CASE OF FIRE

•Don’t panic; stay calm. Follow your family escape plan.

•Get out of the house as quickly as possible. Don’t stop to get

dressed or collect anything.

•Feel doors with the back of your hand before opening them.

If a door is cool, open it slowly. Don’t open a hot door. Keep doors

and windows closed, unless you must escape through them.

•Cover your nose and mouth with a cloth (preferably damp).

Take short, shallow breaths.

•Meet at your planned meeting place outside your home, and do a

head count to make sure everybody got out safely.

•Call the Fire Department as soon as possible from outside.

Give your address, then your name.

•Never go back inside a burning building for any reason.

•Contact your Fire Department for ideas on making your home safer.

Alarms have various limitations. See "Limitations of Smoke Alarms"

for details.

USING THE SILENCE FEATURE

The Silence Feature can temporarily quiet an unwanted alarm for several

minutes. To use this feature, press the “Push to Silence” button on the

cover. The alarm will “chirp” about once a minute (for up to 15 minutes)

to remind you the alarm has been silenced. The “chirping” will stop

when the unit returns to normal operation.

The Silence Feature does not disable the unit—it makes it tem-

porarily less sensitive to smoke. For your safety, if smoke around

the unit is dense enough to suggest a potentially dangerous situa-

tion, it will stay in alarm, or may re-alarm quickly. If you do not

know the source of the smoke, do not assume it is an unwanted

alarm. Not responding to an alarm can result in property loss,

injury or death.

REGULAR MAINTENANCE

This unit has been designed to be as maintenance free as possible, but

there are a few simple things you must do to keep it working properly.

Use only the replacement batteries listed below. The unit may not

operate properly with other batteries. Never use rechargeable

batteries since they may not provide a constant charge.

•Test it at least once a week.

•Clean the Smoke Alarm at least once a month; gently vacuum the

outside of the Smoke Alarm using your household vacuum’s soft

brush attachment. Test the Smoke Alarm. Never use water, cleaners

or solvents since they may damage the unit.

•If the Smoke Alarm becomes contaminated by excessive dirt, dust

and/or grime, and cannot be cleaned to avoid unwanted alarms,

replace the unit immediately.

•Relocate the unit if it sounds frequent unwanted alarms. See

“Locations to Avoid for Smoke Alarms” for details.

•When the battery becomes weak, the Smoke Alarm unit will “chirp”

about once a minute (the low battery warning). This low battery

warning should last for 30 days, but you should replace the battery

immediately to continue your protection.

Choosing a replacement battery:

Your Smoke Alarm requires one standard 9V battery. The following bat-

teries are acceptable as replacements: Duracell #MN1604, (Ultra)

#MX1604; Eveready (Energizer) #522. You may also use a Lithium bat-

tery like the Ultralife U9VL-J for longer service life between battery

changes. These batteries are available at many local retail stores.

Actual battery service life depends on the Smoke Alarm and the environ-

ment in which it is installed. All the batteries specified above are accept-

able replacement batteries for this unit. Regardless of the manufacturer’s

suggested battery life, you MUST replace the battery immediately once

the unit starts “chirping” (the “low battery warning”).

Model SA97B Only:

This model was shipped with a 10-Year Extended Life Lithium battery.

When you replace the original battery, you must replace it with a 10-Year

Extended Life Lithium battery for continued long-life power between

battery changes.

LIMITED WARRANTY

BRK Brands, Inc., ("BRK") the maker of First Alert®brand products

warrants that for a period of ten years from the date of purchase, the

Model SA97B will be free from defects in material and workmanship.

In addition, BRK warrants that for a period of five years from the date of

purchase, the Model SA87B will be free from defects in material and

workmanship. BRK, at its option, will repair or replace this product or

any component of the product found to be defective during the warranty

period. Replacement will be made with a new or remanufactured prod-

uct or component. If the product is no longer available, replacement

may be made with a similar product of equal or greater value. This is

your exclusive warranty.

This warranty is valid for the original retail purchaser from the date of

initial retail purchase and is not transferable. Keep the original sales

receipt. Proof of purchase is required to obtain warranty performance.

BRK dealers, service centers, or retail stores selling BRK products do

not have the right to alter, modify or any way change the terms and

conditions of this warranty.

This warranty does not cover normal wear of parts or damage resulting

from any of the following: negligent use or misuse of the product, use on

improper voltage or current, use contrary to the operating instructions,

disassembly, repair or alteration by anyone other than BRK or an author-

ized service center. Further, the warranty does not cover Acts of God,

such as fire, flood, hurricanes and tornadoes or any batteries that are

included with this unit.

BRK shall not be liable for any incidental or consequential damages

caused by the breach of any express or implied warranty. Except to the

extent prohibited by applicable law, any implied warranty of mer-

chantability or fitness for a particular purpose is limited in duration to the

duration of the above warranty. Some states, provinces or jurisdictions

do not allow the exclusion or limitation of incidental or consequential

damages or limitations on how long an implied warranty lasts, so the

above limitations or exclusion may not apply to you. This warranty gives

you specific legal rights, and you may also have other rights that vary

from state to state or province to province.

How to Obtain Warranty Service

Service: If service is required, do not return the product to your retailer.

In order to obtain warranty service, contact the Consumer Affairs

Division at 1-800-323-9005, 7:30 AM - 5:00 PM Central Standard Time,

Monday through Friday. To assist us in serving you, please have the

model number and date of purchase available when calling.

303 Nelson Avenue, Neosho, MO 64850-8806.

Battery: BRK Brands, Inc. make no warranty, express or implied, written

or oral, including that of merchantability or fitness for any particular

purpose with respect to battery.

IF YOU SUSPECT A PROBLEM

Smoke Alarms may not operate properly because of dead, missing or

weak batteries, a build-up of dirt, dust or grease on the Smoke Alarm

cover, or installation in an improper location. Clean the Smoke Alarm as

described in “Regular Maintenance,” and install a fresh battery, then test

the Smoke Alarm again. If it fails to test properly when you use the test

button, or if the problem persists, replace the Smoke Alarm immediately.

•If you hear a “chirp” once a minute, replace the battery.

•If you experience frequent non-emergency alarms (like those

caused by cooking smoke), try relocating the Smoke Alarm.

•If the alarm sounds when no smoke is visible, try cleaning or

relocating the Smoke Alarm. The cover may be dirty.

•If the alarm does not sound during testing, try installing a new

battery, and make sure it is snapped in securely.

If the Smoke Alarm is still not operating properly, and it is still under

warranty, please see “How to Obtain Warranty Service” in the Limited

Warranty below.

Do not try fixing the alarm yourself – this will void your warranty!

RECOMMENDED LOCATIONS FOR

SMOKE ALARMS

Installing Smoke Alarms in Single-Family Residences

The National Fire Protection Association (NFPA), recommends one

Smoke Alarm on every floor, in every sleeping area, and in every bed-

room. In new construction, the Smoke Alarms must be AC powered and

interconnected. See “Agency Placement Recommendations” for details.

For additional coverage, it is recommended that you install a Smoke

Alarm in all rooms, halls, storage areas, finished attics, and basements,

where temperatures normally remain between 40˚F (4˚C) and 100˚F

(38˚C). Make sure no door or other obstruction could keep smoke from

reaching the Smoke Alarms.

More specifically, install Smoke Alarms:

•On every level of your home, including finished attics and base-

ments.

•Inside every bedroom, especially if people sleep with doors closed.

•In the hall near every sleeping area. If your home has multiple sleep-

ing areas, install a unit in each.

•If a hall is over 40 feet (12 meters) long, install an alarm at each end.

•At the top of the first-to-second floor stairway, and at bottom of

basement stairway.

Specific requirements for Smoke Alarm installation vary from state to

state and from region to region. Check with your local Fire Department

for current requirements in your area. It is recommended AC or AC/DC

units be interconnected for added protection.

BEDROOM

BEDROOM HALL

LIVING ROOM KITCHEN

FINISHED BASEMENT

BEDROOM

BEDROOM LIVING ROOM

DINING ROOM

MULTI-STORY RESIDENCE

SINGLE-STORY RESIDENCE, APARTMENT,

MOBILE HOME

EXISTING HOMES

KITCHEN

REQUIRED TO

MEET NFPA

RECOMMENDATIONS

RECOMMENDED

FOR ADDITIONAL

PROTECTION

KEY: SMOKE ALARMS WITH SILENCE

FEATURES RECOMMENDED FOR

ADDITIONAL PROTECTION

INTERCONNECTED

AC OR AC/DC

SMOKE ALARMS

BEDROOM

BEDROOM HALL

LIVING ROOM KITCHEN

FINISHED BASEMENT

REQUIRED TO

MEET NFPA

RECOMMENDATIONS

RECOMMENDED

FOR ADDITIONAL

PROTECTION

BEDROOM

BEDROOM LIVING ROOM

DINING ROOM

MULTI-STORY RESIDENCE

SINGLE-STORY RESIDENCE, APARTMENT,

MOBILE HOME

KEY:

NEW CONSTRUCTION

SMOKE ALARMS

WITH SILENCE

FEATURES

RECOMMENDED

FOR ADDITIONAL

PROTECTION

KITCHEN

INSTALLING SMOKE ALARMS IN MOBILE HOMES & RVS

For minimum security install one Smoke Alarm as close to each sleeping

area as possible. For more security, put one unit in each room. Many

older mobile homes (especially those built before 1978) have little or no

insulation. If your mobile home is not well insulated, or if you are unsure

of the amount of insulation, it is important to install units on inside walls

only. Smoke Alarms should be installed where temperatures normally

remain between 40˚F (4˚C) and 100˚F (38˚C). WARNING: Test units used

in RVs after the vehicle has been in storage, before every trip, and

once a week while in use. Failure to test units used in RVs as

described may remove your protection.

This equipment should be installed in accordance with NFPA (National Fire

Protection Association) 72 and

101. National Fire Protection Association,

One Batterymarch Park, Quincy, MA 02269-9101. Additional local build-

ing and regulatory codes may apply in your area. Always check com-

pliance requirements before beginning any installation.

AGENCY PLACEMENT RECOMMENDATIONS

NFPA 72 (National Fire Code)

Smoke Alarms shall be installed in each separate sleeping room, outside

each sleeping area in the immediate vicinity of the bedrooms and on

each additional story of the family living unit, including basements and

excluding crawl spaces and unfinished attics.

In new construction, Alarms shall be so arranged that operation of any

one Alarm shall cause the operation of all Alarms within the dwelling.

Smoke Detection-Are More Smoke Alarms Desirable? The required

number of Smoke Alarms might not provide reliable early warning pro-

tection for those areas separated by a door from the areas protected by

the required Smoke Alarms. For this reason, it is recommended that the

householder consider the use of additional Smoke Alarms for those

areas for increased protection. The additional areas include the base-

ment, bedrooms, dining room, furnace room, utility room, and hallways

not protected by the required Smoke Alarms. The installation of Smoke

Alarms in kitchens, attics (finished or unfinished), or garages is not nor-

mally recommended, as these locations occasionally experience condi-

tions that can result in improper operation.

California State Fire Marshal (CSFM)

Early warning detection is best achieved by the installation of fire detec-

tion equipment in all rooms and areas of the household as follows: A

Smoke Alarm installed in each separate sleeping area (in the vicinity, but

outside bedrooms), and Heat or Smoke Alarms in the living rooms, din-

ing rooms, bedrooms, kitchens, hallways, finished attics, furnace rooms,

closets, utility and storage rooms, basements, and attached garages.

LOCATIONS TO AVOID FOR SMOKE ALARMS

For best performance, it is recommended you AVOID installing

Smoke Alarms in these areas:

•Where combustion particles are produced. Combustion particles

form when something burns. Areas to avoid include poorly ventilated

kitchens, garages, and furnace rooms. Keep units at least 20 feet

(6 meters) from the sources of combustion particles (stove, furnace,

water heater, space heater) if possible.

In areas where a 20-foot

(6-meter) distance is not possible – in modular, mobile, or smaller

homes, for example – it is recommended the Smoke Alarm be placed

as far from these fuel-burning sources as possible. The placement

recommendations are intended to keep these Alarms at a reasonable

distance from a fuel-burning source, and thus reduce “unwanted”

alarms. Unwanted alarms can occur if a Smoke Alarm is placed

directly next to a fuel-burning source. Ventilate these areas as much

as possible.

•In air streams near kitchens. Air currents can draw cooking smoke

into the sensing chamber of a Smoke Alarm near the kitchen.

•In very damp, humid or steamy areas, or directly near bathrooms

with showers. Keep units at least 10 feet (3 meters) away from

showers, saunas, dishwashers, etc.

•Where the temperatures are regularly below 40˚ F (4˚ C) or above

100˚ F (38˚C), including unheated buildings, outdoor rooms, porches,

or unfinished attics or basements.

•In very dusty, dirty, or greasy areas. Do not install a Smoke Alarm

directly over the stove or range. Keep laundry room Smoke Alarms

free of dust or lint.

•Near fresh air vents, ceiling fans, or in very drafty areas. Drafts can

blow smoke away from the unit, preventing it from reaching the

sensing chamber.

•In insect infested areas. Insects can clog openings to the sensing

chamber and cause unwanted alarms.

•Less than 12 inches (305mm) away from fluorescent lights. Electrical

“noise” can interfere with the sensor.

•In “dead air” spaces. “Dead air” spaces may prevent smoke from

reaching the Smoke Alarm.

Avoiding Dead Air Spaces

“Dead air” spaces may prevent smoke from reaching the Smoke Alarm.

To avoid dead air spaces, follow the installation recommendations

below.

On ceilings, install Smoke Alarms as close to the center of the ceiling

as possible. If this is not possible, install the Smoke Alarm at least 4

inches (102 mm) from the wall or corner.

For wall mounting (if allowed by building codes), the top edge of

Smoke Alarms should be placed between 4 and 12 inches (102 and 305

mm) from the wall/ceiling line, below typical “dead air” spaces.

On a peaked, gabled, or cathedral ceiling, install the first Smoke

Alarm within 3 feet (0.9 meters) of the peak of the ceiling, measured hor-

izontally. Additional Smoke Alarms may be required depending on the

length, angle, etc. of the ceiling's slope. Refer to NFPA 72 for details on

requirements for sloped or peaked ceilings.

ABOUT SMOKE ALARMS

Battery (DC) operated Smoke Alarms: Provide protection even when

electricity fails, provided the batteries are fresh and correctly installed.

Units are easy to install, and do not require professional installation.

AC powered Smoke Alarms: Can be interconnected so if one unit

senses smoke, all units alarm. They do not operate if electricity fails.

AC with battery (DC) back-up: will operate if electricity fails, provided

the batteries are fresh and correctly installed. AC and AC/DC units must

be installed by a qualified electrician.

Smoke Alarms for Solar or Wind Energy users and battery backup

power systems: AC powered Smoke Alarms should only be operated

with true or pure sine wave inverters. Operating this Smoke Alarm with

most battery-powered UPS (uninterruptible power supply) products or

square wave or “quasi sine wave” inverters will damage the Alarm.

If you are not sure about your inverter or UPS type, please consult with

the manufacturer to verify.

Smoke Alarms for the hearing impaired: Special purpose Smoke

Alarms should be installed for the hearing impaired. They include a visu-

al alarm and an audible alarm horn, and meet the requirements of the

Americans With Disabilities Act. Can be interconnected so if one unit

senses smoke, all units alarm.

All these Smoke Alarms are designed to provide early warning of fires if

located, installed and cared for as described in the user’s manual, and if

smoke reaches them. If you are unsure which type of Smoke Alarm to

install, refer to Chapter 2 of the National Fire Protection Association

(NFPA) Standard 72 (National Fire Alarm Code) and NFPA 101 (Life

Safety Code). National Fire Protection Association, One Batterymarch

Park, Quincy, MA 02269-9101. Local building codes may also require

specific units in new construction or in different areas of the home.

SPECIAL COMPLIANCE CONSIDERATIONS

This Smoke Alarm alone is not a suitable substitute for complete fire

detection systems in places housing many people—like apartment

buildings, condominiums, hotels, motels, dormitories, hospitals, long-

term health care facilities, nursing homes, day care facilities, or group

homes of any kind—even if they were once single-family homes. It is not

a suitable substitute for complete fire detection systems in warehouses,

industrial facilities, commercial buildings, and special-purpose non-resi-

dential buildings which require special fire detection and alarm systems.

Depending on the building codes in your area, this Smoke Alarm may be

used to provide additional protection in these facilities.

The following information applies to all four building types below:

In new construction, most building codes require the use of AC or

AC/DC powered Smoke Alarms only. In existing construction, AC,

AC/DC, or DC powered Smoke Alarms can be used as specified by

local building codes. Refer to NFPA 101 (Life Safety Code) or NFPA 72

(National Fire Alarm Code), local building codes, or consult your Fire

Department for detailed fire protection requirements in buildings not

defined as “households.”

1. Single-Family Residence:

Single family home, townhouse. It is recommended Smoke Alarms be

installed on every level of the home, in every bedroom, and in each bed-

room hallway.

2. Multi-Family or Mixed Occupant Residence:

Apartment building, condominium. This Smoke Alarm is suitable for use

in individual apartments or condos, provided a primary fire detection

system already exists to meet fire detection requirements in common

areas like lobbies, hallways, or porches. Using this Smoke Alarm in

common areas may not provide sufficient warning to all residents or

meet local fire protection ordinances/regulations.

3. Institutions:

Hospitals, day care facilities, long-term health care facilities. This Smoke

Alarm is suitable for use in individual patient sleeping/resident rooms,

provided a primary fire detection system already exists to meet fire

detection requirements in common areas like lobbies, hallways, or

porches. Using this Smoke Alarm in common areas may not provide

sufficient warning to all residents or meet local fire protection ordi-

nances/regulations.

4. Hotels and Motels:

Also boarding houses and dormitories. This Smoke Alarm is suitable for

use inside individual sleeping/resident rooms, provided a primary fire

detection system already exists to meet fire detection requirements in

common areas like lobbies, hallways, or porches. Using this Smoke

Alarm in common areas may not provide sufficient warning to all resi-

dents or meet local fire protection ordinances/regulations.

First Alert®is a registered trademark of the First Alert Trust.

Printed in Mexico M08-0020-002 J1 07/04

LIMITATIONS OF SMOKE ALARMS

Smoke Alarms have played a key role in reducing deaths resulting from

home fires worldwide. However, like any warning device, Smoke Alarms

can only work if they are properly located, installed, and maintained, and

if smoke reaches them. They are not foolproof.

Smoke alarms may not waken all individuals. Practice the escape

plan at least twice a year, making sure that everyone is involved – from

kids to grandparents. Allow children to master fire escape planning and

practice before holding a fire drill at night when they are sleeping. If

children or others do not readily waken to the sound of the Smoke

Alarm, or if there are infants or family members with mobility limitations,

make sure that someone is assigned to assist them in fire drill and in the

event of an emergency. It is recommended that you hold a fire drill while

family members are sleeping in order to determine their response to the

sound of the Smoke Alarm while sleeping and to determine whether

they may need assistance in the event of an emergency.

Smoke Alarms cannot work without power. Battery operated units

cannot work if the batteries are missing, disconnected or dead, if the

wrong type of batteries are used, or if the batteries are not installed cor-

rectly. AC units cannot work if the AC power is cut off for any reason

(open fuse or circuit breaker, failure along a power line or at a power sta-

tion, electrical fire that burns the electrical wires, etc.). If you are con-

cerned about the limitations of battery or AC power, install both types of

units.

Smoke Alarms cannot detect fires if the smoke does not reach

them. Smoke from fires in chimneys or walls, on roofs, or on the other

side of closed doors may not reach the sensing chamber and set off the

alarm. That is why one unit should be installed inside each bedroom or

sleeping area—especially if bedroom or sleeping area doors are closed

at night—and in the hallway between them.

Smoke Alarms may not detect fire on another floor or area of the

home. For example, a stand-alone unit on the second floor may not

detect smoke from a basement fire until the fire spreads. This may not

give you enough time to escape safely. That is why recommended mini-

mum protection is at least one unit in every sleeping area, and every

bedroom on every level of your home. Even with a unit on every floor,

stand-alone units may not provide as much protection as interconnect-

ed units, especially if the fire starts in a remote area. Some safety

experts recommend installing interconnected AC powered units with

battery back-up (see “About Smoke Alarms”) or professional fire detec-

tion systems, so if one unit senses smoke, all units alarm.

Interconnected units may provide earlier warning than stand-alone units

since all units alarm when one detects smoke.

Smoke Alarms may not be heard. Though the alarm horn in this unit

meets or exceeds current standards, it may not be heard if: 1) the unit is

located outside a closed or partially closed door, 2) residents recently

consumed alcohol or drugs, 3) the alarm is drowned out by noise from

stereo, TV, traffic, air conditioner or other appliances, 4) residents are

hearing impaired or sound sleepers. Special purpose units, like those

with visual and audible alarms, should be installed for hearing impaired

residents.

Smoke Alarms may not have time to alarm before the fire itself

causes damage, injury, or death, since smoke from some fires may

not reach the unit immediately. Examples of this include persons

smoking in bed, children playing with matches, or fires caused by

violent explosions resulting from escaping gas.

Smoke Alarms are not foolproof. Like any electronic device, Smoke

Alarms are made of components that can wear out or fail at any time.

You must test the unit weekly to ensure your continued protection.

Smoke Alarms cannot prevent or extinguish fires. They are not a substi-

tute for property or life insurance.

Smoke Alarms have a limited life. The unit should be replaced imme-

diately if it is not operating properly. You should always replace a Smoke

Alarm after 10 years from date of purchase. Write the purchase date on

the space provided on back of unit.

First Alert Sa87Cn Users Manual M08_0020_002_E(SA87CN/SA97CN)

SA87CN to the manual 885b4bd1-e72b-41a2-a062-7ffd057712e3

Navigation menu

Versions of this User Manual:

Views

Navigation