Fisher And Paykel Joiner Kit Silver Installation Guide 819265 Instructn Sheet

: Fisher-And-Paykel Fisher-And-Paykel-Joiner-Kit-Silver-Installation-Guide-685453 fisher-and-paykel-joiner-kit-silver-installation-guide-685453 fisher-and-paykel pdf

Open the PDF directly: View PDF .
Page Count: 7

Joiner Kit

For Fisher & Paykel Models: C270, E249T, E240B, E210, E381T, E372B, N388, E388,

C450, E450, E402B, E411T, E415H, E413T, E406B, E440T, E442B, E521T & E522B

Introduction Date: October 2007 Pt No.819265 INSTRUCTION KIT JOINER RF 1

KIT COMPONENTS

Part Illustration Description

Rear Bracket

Front Lower Bracket

Front Upper Bracket

Extrusion Support

Extrusion Cover

Screw Type A:

#8x16 PAN PHIL (7)

Screw Type B:

#5x20 HEX PHIL (6)

JOINER KIT PART NUMBERS

Silver – F&P Part Number 819264

White – F&P Part Number 819263

KIT APPLICATION

This kit is designed for use on 1595mm / 62” & 1695mm / 66”

high cabinet models, incorporating the “B, C, D & G” series

refrigerator or freezer having curved or flat door styling.

Note: This kit can be used for combining any of the following

products of the same height:

1695mm / 66” Tall Cabinets:

N388, E388, C450, E450, E402B, E411T, E415H, E440T,

E442B, E521T, E522B

1595mm / 62” Tall Cabinets:

C270, E249T, E240B, E210, E381, E372B, E413T, E406B

TOOLS REQUIRED

1. Philips type screwdriver

2. Flat blade screwdriver

3. 19mm Socket

Joiner Kit

For Fisher & Paykel Models: C270, E249T, E240B, E210, E381T, E372B, N388, E388, C450, E450, E402B, E411T, E415H, E413T, E406B,

E440T, E442B, E521T & E522B

Introduction Date: October 2007 Pt No.819265 INSTRUCTION KIT JOINER RF 2

Models C270 / E249T / E240B / E210 E381T / E372B / E402B / E411T/ E415H / C450 /

E450 / N388 / E388 E413T / E406B / E440T / E442B E521T / E522B

Product Dimensions (mm)

A Width 525 635 680 790

Combined Models (mm/inches) 525+525 Model 525+635 Model 525+680 Model 635+635 Model 635+680 Model 635+790 Model 680+680 Model 680+790 Model 790+790 Model

B Height 1595 / 62 ¾ 1595 / 62 ¾ 1595 / 62 ¾ 1695 / 66 ¾ 1695 / 66 ¾ 1695 / 66 ¾ 1695 / 66 ¾ 1695 / 66 ¾ 1695 / 66 ¾

C Width 1075 / 42 3/8 1185 / 46 5/8 1230 / 48 ½ 1295 / 51 1340 / 52 ¾ 1450 / 57 1385 / 54 ½ 1495 / 58 7/8 1605 / 63 1/8

D Depth of curved door not including

handle 572 / 22 ½ 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8

E Depth of flat door not including

handle N/A 685 / 27 685 / 27 685 / 27 685 / 27 685 / 27 685 / 27 685 / 27 685 / 27

Cabinetry Dimensions - including minimum clearances

F Inside height 1645 / 64 ¾ 1645 / 64 ¾ 1645 / 64 ¾ 1745 / 68 ¾ 1745 / 68 ¾ 1745 / 68 ¾ 1745 / 68 ¾ 1745 / 68 ¾ 1745 / 68 ¾

1. Flush with refrigerator chassis – full door rotation

G Inside width 1115 / 44 1205 / 47 ½ 1270 / 50 1335 / 51 ½ 1380 / 54 3/8 1490 / 58 5/8 1425 / 56 1/8 1535 / 60 ½ 1645 / 64 ¾

H Inside depth flush to chassis 502 / 19 ¾ 620 / 24 3/8 620 / 24 3/8 620 / 24 3/8 620 / 24 3/8 620 / 24 3/8 620 / 24 3/8 620 / 24 3/8 620 / 24 3/8

2. Flush with refrigerator door – 90° door rotation

I Inside width 1125 / 44 3/8 1235/48 5/8 1280/ 50 ½ 1345 / 53 1390/54 ¾ 1500/59 1435/56 ½ 1545/60 7/8 1655/65 1/8

J Inside depth flush to curved door 575 / 22 5/8 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½

K Inside depth flush to flat door N/A 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8

3. Flush with refrigerator door – full door rotation

L Inside width 1355 / 53 3/8 1465 / 57 ¾ 1510 / 59 ½ 1575 / 62 1620 / 63 ¾ 1730 / 68 1/8 1665 / 65 ½ 1775 / 69 7/8 1885 / 74 ¼

M Inside depth flush to curved door 575 / 22 5/8 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½ 724 / 28 ½

N Inside depth flush to flat door N/A 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8 696 / 27 3/8

Minimum clearances

O Side clearance flush with

refrigerator chassis 20 / ¾ 20 / ¾ 20 / ¾ 20 / ¾ 20 / ¾ 20 / ¾ 20 / ¾ 20 / ¾ 20 / ¾

P Side clearance flush with door 90

rotation 25 / 1 25 / 1 25 / 1 25 / 1 25 / 1 25 / 1 25 / 1 25 / 1 25 / 1

Q Side clearance flush with door full

rotation 140 / 5 ½ 140 / 5 ½ 140 / 5 ½ 140 / 5 ½ 140 / 5 ½ 140 / 5 ½ 140 / 5 ½ 140 / 5 ½

R Rear including evaporator tray 30 / 1 1/8 30 / 1 1/8 30 / 1 1/8 30 / 1 1/8 30 / 1 1/8 30 / 1 1/8 30 / 1 1/8 30 / 1 1/8 30 / 1 1/8

S Vent 50 / 2 50 / 2 50 / 2 50 / 2 50 / 2 50 / 2 50 / 2 50 / 2 50 / 2

Joiner Kit

For Fisher & Paykel Models: C270, E249T, E240B, E210, E381T, E372B, N388, E388, C450, E450, E402B, E411T, E415H, E413T, E406B,

E440T, E442B, E521T & E522B

Introduction Date: October 2007 Pt No.819265 INSTRUCTION KIT JOINER RF 3

CAVITY / VENTILATION REQUIREMENTS

Surround Kits are available, please contact Fisher & Paykel Customer Care 0800 FP CARE or 0800 37 2273 for further information on kit sizes and finishes.

Note: For full draw/shelf access the

doors need to open past 90°

Joiner Kit

For Fisher & Paykel Models: C270, E249T, E240B, E210, E381T, E372B, N388, E388,

C450, E450, E402B, E411T, E415H, E413T, E406B, E440T, E442B, E521T & E522B

Introduction Date: October 2007 Pt No.819265 INSTRUCTION KIT JOINER RF

4

PREPARE FOR INSTALLATION

Step1.

1. Check that the internal cupboard cavity dimensions are

correct for the type of installation you require.

2. Unpack the refrigerator and freezer cabinets from their

separate delivery cartons (see individual cartons for

unpacking procedures).

3. Ensure the floor and/or the cupboards are protected from

damage during the unpacking and assembly of the

cabinets.

4. Check the refrigerator and freezer doors are hinged on the

desired side.

5. Check that the Kit is complete (refer to Joiner Kit parts list

on page 1).

Note: due to the size of the refrigerator cabinets, it is essential

that any assembly of the kit be undertaken with a minimum of

two able-bodied persons.

INSTALLATION PROCEDURE

Step 2.

If your refrigerator has a unit compartment cover at the back,

remove using a Phillips type screw driver (USA market only).

This will be re-attached later.

Looking at the back of the two products, locate the Rear

Bracket onto the rear bottom left hand edge of the right hand

side product. Care must be taken to line up the top edge of the

Rear Bracket with the bottom edge of the white back panel.

Secure the Rear Bracket with 3 of the screws (Type A, self

tapping, silver). These 3 screws are mounted from the side.

Please note there are no pre-drilled holes for these screws

which hold the rear bracket onto the side of the cabinet.

Right hand side cabinet

Step 2

Step 3.

Locate the left hand side cabinet’s bottom right rear wall within

the open “U” section in the rear bracket. Ensure that the cabinet

sits firmly with the rear bracket.

Do not secure with screws (see page 4).

Right hand side cabinet

Left hand side cabinet

Step 3

Step 4.

Locate the front adjustable feet. One can be found at each of

the cabinet’s front lower corners.

Adjust the two feet by turning either clockwise or anti-clockwise

until the two cabinets are level.

Step 4

Step 5.

Remove the three screw hole caps from the top surface of each

of the cabinets with a small flat bladed screwdriver by gently

prising them loose. The caps can be found on the front edge of

the top surface of the cabinets, opposite side to the hinge.

Ensure that the top panel is not scratched or deformed during

this process. The total of six screw hole caps are not required

to be used with the kit.

Step 5

Joiner Kit

For Fisher & Paykel Models: C270, E249T, E240B, E210, E381T, E372B, N388, E388,

C450, E450, E402B, E411T, E415H, E413T, E406B, E440T, E442B, E521T & E522B

Introduction Date: October 2007 Pt No.819265 INSTRUCTION KIT JOINER RF 5

Step 6.

Locate the front upper bracket on the top surface of the two

cabinets, taking care to line up the bosses on the Front Upper

Bracket, with the six screw points.

Note that the large centered rectangular section on the

underside of the front upper bracket acts as a spacer between

the two cabinets. Partially engage all of the screws (Type B,

hex head, silver) prior to their final tightening.

Step 6

Step 7.

Ensure the left cabinet is properly located within the rear

bracket and that the cabinets are level. Secure the left cabinet

to the rear bracket using 3 of the screws (Type A, self tapping,

silver).

Now replace the unit compartment cover at the back using a

Phillips type screw driver (USA market only)

Left hand

side cabinet

Right hand

side cabinet

Step 7

Step 8

To access the adjustable feet and to locate the front lower

bracket, the joined cabinets must be tilted backwards

approximately 60 degrees. This is a two person operation.

The person at the rear of the cabinets must acknowledge that

they have a secure grip of the cabinets prior to any work being

undertaken by the second installer.

Care must be taken not to damage either the cabinets/floor or

the surrounding cupboards during this operation.

60

Step 8

Step 9

Remove the two Levelling Feet by rotating them anti-clockwise

then remove the two bolts.

Note: C450, E450, E440T, E442B, E521T and E522B may

have an extra component as part of the levelling foot assembly,

this being a stepped plastic washer. If this part is located, it is to

be removed as it is not required to be used with this kit.

Step 9

Joiner Kit

For Fisher & Paykel Models: C270, E249T, E240B, E210, E381T, E372B, N388, E388,

C450, E450, E402B, E411T, E415H, E413T, E406B, E440T, E442B, E521T & E522B

Introduction Date: October 2007 Pt No.819265 INSTRUCTION KIT JOINER RF

6

The Front Lower Bracket is now located on the underside of the

Cabinets. Care must be taken to orient the bracket so that the

two small tabs are located with the slots on the underside of the

Cabinet.

Step 10

The two Leveling Feet Mounting Bolts are firmly located back

onto the cabinet, securing the Front Lower Bracket.

The two Leveling Feet are now screwed back into their existing

position. Once assembled, lower the Refrigerator assembly

back to a standing position, taking care not to damage it or the

surrounding cupboards/floor.

Step 10

Step 11

Before loading the Trim Panel Assembly, The six Type B

Screws must be loosened from the Front Top Bracket, so that

the bracket can be freely moved up and down (approximately

5mm/1/8”).

Step 11

Step 12

Open both the cabinet doors for easy access to the center join

of the two Cabinets.

Step 12

Step 13

If using kit on shorter models, cut Trim Panel Assembly

(Extrusion cover & Extrusion support) to length shown in table

below.

Model Trim Height

(mm / inches)

C270, E249T, E240B, E210, E381T,

E372B, E413T, E406B 1562 / 61 ½

N388, E388, C450, E450, E402B,

E411T, E415H, E440T, E442B,

E521T, E522B

1662 / 65 ½

(Standard

Height)

Locate the Trim Panel Assembly on the upright tab that

protrudes from the Front Lower Bracket.

Step 13

Joiner Kit

For Fisher & Paykel Models: C270, E249T, E240B, E210, E381T, E372B, N388, E388,

C450, E450, E402B, E411T, E415H, E413T, E406B, E440T, E442B, E521T & E522B

Introduction Date: October 2007 Pt No.819265 INSTRUCTION KIT JOINER RF 7

Step 14

Locate the Trim Panel Assembly under the Front Upper

Bracket. The Front Upper Bracket should be free to move up

and down to aid installation (see diagram 13).

Step 14

Step 15

Tighten the 6 Type B Screws to locate the Front Upper Bracket.

Secure the Trim Panel Assembly with one screw (Type A, Self

Tapping, Silver).

Step 15

COMPLETE THE INSTALLATION PROCEDURE

Step 16

Close the Refrigerator doors, ensuring that all door seals sit

flush against the front walls of the Cabinets.

Step 17

Complete the installation by locating the assembled combined

cabinets within the Cupboard Cavity (refer to page 2 for

Cupboard Cavity dimensions).

Step 17

Step 18

If doors are out of line after installation is complete, undo top

door hinge bracket of the un-aligned door by unscrewing all 3

screws halfway. Align by moving the door left or right. Once

aligned, re-screw the hinge bracket.

Ensure the front leveling feet are adjusted to take the load of

the combined cabinets. Note: Adjusting the leveling feet can

also affect the door alignment.

Step 18