Fitness Quest Total Gym 1100 Users Manual TG1700 Club OWNERS GUIDE

1100 to the manual 32f178c8-c349-8bc4-ad12-0c3150ed8bc3

2015-01-25

: Fitness-Quest Fitness-Quest-Total-Gym-1100-Users-Manual-234646 fitness-quest-total-gym-1100-users-manual-234646 fitness-quest pdf

Open the PDF directly: View PDF PDF.
Page Count: 7

DownloadFitness-Quest Fitness-Quest-Total-Gym-1100-Users-Manual- TG1700 Club OWNERS GUIDE  Fitness-quest-total-gym-1100-users-manual
Open PDF In BrowserView PDF
OWNER’S MANUAL
Dedication to Quality
Fitness Quest warrants this product to be free from all
defects in material and workmanship when used
according to the manufacturer’s instructions.
See Limited Warranty Card for details.
If you have any comments or questions contact our
Customer Service Department, toll free at 1-800-321-9236,
Monday through Friday, 9:00 am to 5:00 pm, EST.
Please record the following information and keep for reference.
Serial #: ___________________
Date Of Purchase: ___________

For Maximum
Effectiveness and
Safety, Please Read
This Owner’s Manual
Before Using Your
Total Gym 1100.

Save your sales receipt.
(You may wish to staple it into this manual.)

© 2004 Fitness Quest® Inc. All rights reserved. Made in China.
©1998, 1999, 2000, 2001, 2003, 2004 Total Gym Fitness, LLC. All rights reserved. Total Gym® is a registered
trademark. U.S. Patents #D405,132, #5,967,955; ROC Patents #ND-060792; PRC Patent #ZL 97 2 28552.0.
No part of this booklet may be reproduced or utilized in any form, by any means, electronic, mechanical or
otherwise, without the express written consent of the copyright holder.
9/1/04

exercise system

TOTAL GYM® PARTS LIST
PART #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15

PART DESCRIPTION
Vertical Column
Tube Rollers
Stoppers
Screws
Washers
Nuts
Screws
Upper Rail (right & left)
Center Support Rail
Rectangular Tube Caps
Plastic Bushings
Shaft
Lower Rail
Platform
Platform Rail

QTY.
1
2
4
3
14
7
4
1
1
6
4
1
1
1
1

PART #
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

PART DESCRIPTION
Left Fender
Right Fender
Fender Bolts
Wheels
Wheel Spacer Tube
Adjustment Tube
Plastic Slide Bushing
Square Tube Cap
Round Tube Caps
Eyebolts
Eyebolt Nuts
Nut Caps
Spring Loaded Pin
“C” Pin
Cable Assembly

QTY.
2
2
4
4
4
1
1
1
6
2
2
2
1
1
1

PART # PART DESCRIPTION
QTY.
31
Pulley Assembly
4
32
Handle Assembly
2
33
Multi Function Attachment
1
34
Grips
2
35
Foam Pads
2
36
Pins
3
37
Leg Pulley
1
38
Bracket
1
39
“D” Ring
1
40
Harness
1
LITERATURE PACK
41
Owner’s Manual
1
42
Exercise Booklet
1
43
Warranty Card
1
50
Safety Hitch Pin
1

Congratulations on purchasing your
new Total Gym® 1100.
With this product in your home, you have everything you need to start your
own workout program, to tone and strengthen the important muscle groups
of your upper and lower body. This is vital for all of us, regardless of age,
sex, or fitness level, and regardless of whether your primary goal is body
sculpting, weight control, health maintenance, or more energy for
daily activities.
Strength training not only tones and conditions the muscles we use every
day to stand, walk, lift, and turn; it can actually transform our body
composition. By reducing body fat and increasing the proportion of lean
muscle in our bodies, strength training can effectively turn up our metabolic
thermostat, so that we burn calories all the time, no matter what we’re
doing.

23

22

A

It’s easy—all you have to do is spend 15 to 20 minutes a day, 3 to 4 days
per week on your Total Gym 1100 to start realizing the benefits.

24
26
28

29

27

Be sure to read through this Owner’s Manual carefully.
It is the authoritative source of information about your
Total Gym 1100.

21
24
27

If you have questions about your Total Gym 1100, please call
Customer Service at 1-800-321-9236,
Monday through Friday, 9:00 AM to 5:00 PM, Eastern Standard Time.

26
25

TABLE OF CONTENTS
Safety Instructions & Warnings . . .
Product Specifications . . . . . . . . .
Set Up . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . .
Starting Out . . . . . . . . . . . . . . . . . .
Inspection, Maintenance & Storage
Parts List and Exploded Drawing . .

9/1/04

— 3 —

.
.
.
.
.
.
.

.
.
.
.
.
.
.

.
.
.
.
.
.
.

.
.
.
.
.
.
.

.
.
.
.
.
.
.

. . . . . . . .4
. . . . . . . .5
. . . . . . . .6-7
. . . . . . . .8-10
. . . . . . . .11
. . . . . . . .12-13
. . . . . . . .14

SAFETY INSTRUCTIONS AND WARNINGS - Please reference Product Specifications diagram on page 5.
WARNING
Warning Label 1.

Warning Label 2.

Warning Label 3.
(3 locations)

Warning Label 4.

Warning Label 5.
(4 locations)

5.

a. Release Spring Loaded Pin (on left side rail) as shown.
b. Fold Vertical Column down towards the center of the unit.

FAILURE TO READ AND FOLLOW THE SAFETY INSTRUCTIONS STATED IN THE
OWNER’S MANUAL MAY RESULT IN POSSIBLE SERIOUS INJURY OR DEATH.
KEEP CHILDREN AWAY. MAXIMUM USER WEIGHT 275 LBS.
REPLACE THIS LABEL IF DAMAGED, ILLEGIBLE OR REMOVED.

c. Then insert Safety Hitch Pin at bottom of vertical column.

Spring
Loaded
Pin
Fig. 5b
Fold
Vertical
Column
down

WARNING
Fig. 5c
Insert
Safety
Hitch Pin

MAKE SURE ADJUSTMENT PIN IS LOCKED IN PLACE BEFORE BEGINNING EXERCISES.

WARNING

6.

Slide the Glideboard towards the bottom of unit shown in Figure 6.

CRUSH HAZARD, KEEP HANDS CLEAR DURING FOLDING.
6.

WARNING
BE CAREFUL NOT TO BUMP HEAD WHEN LEG ATTACHMENT IS IN PLACE.

WARNING

7.

PINCH POINT. KEEP HANDS AWAY FROM THE FENDER.

CAUTION
Caution Label 1.

Fig. 5a

8.

REMOVE MULTI FUNCTION ATTACHMENT FROM FRAME WHEN NOT REQUIRED
FOR THE SPECIFIC EXERCISE.

With caution, to avoid pinched fingers or hands, grab the top of the
Glideboard and slowly pull the unit up allowing the rollers to bring the
back of the unit towards the center. Keep approximately 12” apart.

Fig. 7 & 8
Lift Here

Continue to fold the exerciser together until it is completely folded
and roll the exerciser into a closet for storage. To store under a bed,
simply lower the exerciser to the floor and roll under the bed.
Do not store unit in upright position when folded.

CAUTION
Caution Label 2.

WARNING

KEEP HAIR, FINGERS, LOOSE CLOTHING, PETS, AND CHILDREN AWAY FROM HINGES
AND OTHER MOVING PARTS TO AVOID SERIOUS INJURY. ALSO, BE SURE TO HAVE ALL
PINS LOCKED IN PLACE BEFORE GETTING ON YOUR TOTAL GYM®
TO AVOID SEVERE INJURY.

Before beginning this or any exercise program, consult a physician or health professional, who can assist you
in planning a program appropriate for your age andphysical condition. This is especially important if you are over age
35 or have pre-existing health problems.
Do not overexert yourself. Stop exercising immediately and consult your doctor if you experience pain or tightness
in your chest, irregular heart beat, shortness of breath, or if you feel faint, nauseous, or dizzy.

CRUSH HAZARD, KEEP HANDS CLEAR DURING FOLDING.

Back
Crossbar

TO REMOVE THE GLIDEBOARD
You can also remove the Glideboard if you need to fit the exerciser under a narrow
space (between 6” and 8”).

This product is designed for home use only. It is not intended for commercial or institutional use. Use only as
instructed. Do not stand on the product.

IMPORTANT: The Glideboard weighs approximately 15 lbs. Use caution when
lifting it off of the exerciser. Lifting incorrectly may result in user injury.

The Total Gym is not intended for use by children. Keep this and all fitness equipment out of the reach of children.
1.

With exerciser laying flat on the floor, disconnect the pulley from
the hook on the underside of the glideboard.

Inspect your exerciser before each use to ensure proper operation. Do not use this equipment unless all moving
parts, including cables and pulleys are working properly. See pages 12 &13 for details on inspection, maintenance
and storage.

2.

Tilt up the glideboard and slide it off the frame
of the exerciser. When the bench is completely off
the exerciser, set it aside.

The exerciser should only be used on a mat or carpeted surface to prevent unexpected movement of the unit.

3.

Pull the Spring Loaded Pin to release the Rail and fold the
exerciser together as shown above in Figure 7 & 8 Be sure
you release the Spring Loaded Pin before folding.

Keep fingers, loose clothing, and hair away from moving parts.

Use only the accessory items recommended by the manufacturer.
To avoid serious injury, care should be taken at all times when getting on and off this or any exercise equipment.

— 4 —

— 13 —

Fig. 2

12”

Front
Crossbar

PRODUCT SPECIFICATIONS

INSPECTION, MAINTENANCE & STORAGE
INSPECT YOUR TOTAL GYM 1100 PRIOR TO EACH USE
Before using your Total Gym 1100 for your workout session, be sure to make the
following inspection:
•

Make sure the equipment is fully opened and sitting on a solid, level surface with plenty of
clearance on all sides. Unit should be used on a mat or on carpeted surfaces only.

•

Make sure all the Hitch Pins are securely in place and locked into position.

•

Check that the Pulley is attached securely to the loop on the top underside of
the glideboard.

•

Check that the Cables are traveling correctly in the groove of each pulley.

•

Make sure the Cable is securely fastened to each Hand Grip.

•

Check that the Multi Function Attachment or other accessories are installed
correctly when in use.

•

Make sure the Glideboard is gliding smoothly along the frame.

ROUTINE MAINTENANCE
•

•

•

Vertical Height
Adjustment Column
Height
Adjustment
“C” Pin
Arm Pulley
Assembly

WARNING
LABEL 1
WARNING
LABEL 2

Spring loaded
pin (located on
side of rail)

Height
Adjustment
Lever

Periodically check the following parts for signs of fraying or other wear: the cable,
pulleys, wheels, glideboard, accessories and frame. If the cable, pulleys, frame or wheels
need replaced – do not use your unit, wait until the part is replaced.
If any other part than the ones listed above needs to be replaced, do not use that part until
it is replaced.
®

Glideboard
WARNING
LABEL 3

Roller
Safety
Hitch Pin

Front
Crossbar

CAUTION
LABEL 2

Top Inner
Rail

Center Support Rail

Roller

Back Crossbar
Bottom Outer Rail

®

Never use a lubricant such as WD-40 or ArmorAll to lubricate or clean the unit. Use only
®
3-in-1 oil or machine oil to lubricate the axles of the wheel or pulley, not the roller surface.

Leg Pulley Accessory Kit
Pulley/D-Ring
Assembly

TO STORE YOUR TOTAL GYM 1100
Follow these easy steps to store your exerciser properly:
Foot
Harness

1.

Remove all accessories and attachments.

2.

Remove Safety Hitch Pin and Safety Pin from Vertical Column.

3.

Be sure the Cable Pulley is attached to the underside of the glideboard for folding.

4.

Position one foot on back crossbar to keep the product from lifting off the floor. With one
hand on the rail, grasp the height adjustment “C” pin and pull it out from the height
adjustment column. Slowly lower the rails until they rest on the back crossbar.

5.

CAUTION
LABEL 3

Cable

Handle

Wipe down your Total Gym 1100 on a regular basis using a clean cloth and alcohol or
®
®
alcohol-based products like Windex or 409 . Do not leave towels or workout clothing
laying or hanging on the equipment.

WARNING
LABEL 5

Lower the height adjustment column all the way down until it rests on the center rail.

Clip

Leg Pulley
Bracket

Allen
Wrenches

For use with
leg pulley
accessory only.

Packed in the leg pulley
accessory kit

CAUTION
LABEL 1

Foam
Pad
Brackets

LENGTH:

Stopper

— 12 —

Multi Function Attachment

1 Large
Hitch Pin

Rope

Clip

2 Large
Hitch
Pins

WARNING
LABEL 4

HEIGHT:
WIDTH:

folded 501/2”
in use 88”
folded 81/2”
in use 44”
161/8”

WEIGHT:
58 lbs.
MAX. USER WEIGHT:

— 5 —

275 lbs.

STARTING OUT

SET UP
Your product comes with:
• Safety Hitch Pin located at the bottom of the Vertical Column, which must be removed prior to unfolding.
• One (1) Spring Loaded Pin locked into the base of the left rail by the height adjustment tube. Left side is determined
by standing behind the unit facing the Vertical Column.
IMPORTANT: To Prevent Injury – Be sure the spring-loaded pin is locked securely into place in the left
rail before using unit. This will prevent the height adjustment column from falling forward.
• One Large Hitch Pin for Leg Pulley Bracket is located in the Leg Pulley Accessory Kit as well as two Large Hitch Pins
for the Multi Function Attachment.
IMPORTANT: Before using the Multi Function Attachment or Leg Pulley Accessory be sure the Hitch Pins are
securely inserted (see page 8, 9 & 11 of this manual for directions).

Wear athletic shoes and comfortable light clothing when exercising on the Total Gym 1100. Do
not exercise barefoot. Check your exerciser before using to ensure that all the parts are in place
and working properly (see page 12 & 13 for details on inspection, maintenance and storage).
Adult supervision is required at all times.
NOTE: The Rails and Glideboard can be raised to any desired level on the Height
Adjustment Column depending upon your degree of fitness. Please note, however,
that the Rails
cannot be raised to the highest position on the Height Adjustment Column when
the
Leg Pulley Bracket is attached to the column.
Be sure you have plenty of free space around the exerciser so that performing on
the Total Gym 1100, as well as getting on and off, is convenient and safe.
Each time you raise or lower the Adjustment Column, be sure you hold it to keep it from
dropping to the floor.

1.

Pull the product out of the shipping box. Remove all packaging
materials, including tape and cardboard inserts, from your unit.

Begin using the product at a low incline. As your fitness level progresses, increase the incline to
increase the intensity and improve your muscle strength. Don’t be in a hurry to exercise at a high
intensity level; start out easily and build gradually. The Total Gym 1100 is as easy as 1-2-3
to use, so read on.

Lift Here
3.

2.

Lay product on the floor with glideboard side up. Make sure you have
plenty of space on both ends of the product. Slide the glideboard as far
as it will go towards the Front Crossbar before you begin lifting unit.

1.

Important Things to Remember When Using the Total Gym 1100
• Always have control of the glideboard before getting on and off the exerciser.
• Keep your feet on the floor when getting on and off the exerciser. Only remove
them from the floor for the duration of the exercise.
• If you are using the handles, hold onto them as you get on and off the glideboard.

3.

Lift the exerciser up by holding it at the top of the rails. Using your foot,
slowly spread the unit open at the bottom approximately 12 inches so
that it rests firmly on the Front and Back Crossbars not allowing it to go
too far.

2.

Exercising with the Handles Only
Grasp the handles which are attached to the cable and slide the glideboard to a position
in which you can comfortably sit or lay down when performing the desired exercise (see
Exercise Booklet). Be sure to keep your feet on the floor until you are in the correct
position for the specific exercise. Then, if the exercise calls for your feet to be off the
floor, place your feet as specified in the instructions.

3.

Exercising with the Multi Function Attachment Only
Slide the glideboard to a position in which you can comfortably sit or lay down on when
performing the desired exercise (see your Exercise Booklet). Keep your feet on the
ground until you are in the correct position and feel comfortable. Then, place your feet in
the proper position and begin to exercise.

4.

5.

Make sure the handles are out to the sides before
you begin to unfold your unit. Keep hands and
fingers away from pulley. Hold onto the top center
of glideboard and begin rolling rear rollers. Spread
the unit out until it is flat on the floor. Be careful to
do this slowly.
Be sure to support the frame in the center to
avoid having the product drop suddenly onto
the floor or pinch fingers.

(a) Remove Safety Hitch Pin from bottom of Vertical
Column. Remove plastic packing ties from the top
and bottom of the Vertical Column. Pull out the
Spring Loaded Pin Knob located at the left rail
(NOTE - pin shown in picture is on right side) to
release Spring Loaded Pin. Continue to hold pin out
while performing the next step.

— 6 —

4.

12”

Back
Crossbar

Front
Crossbar

Hold Here While Lowering
To The Ground

5a.

Safety
Hitch Pin

When starting your exercise program, begin with the basic exercises shown in the Exercise
Booklet included with your Total Gym 1100 to familiarize yourself with the movements. Use the
lowest incline level to start with – you can work up to a higher incline level in the weeks and
months to come.
For the specific Total Gym 1100 exercises and programs, study and follow the
instructions in the Exercise Booklet included with your product.

Spring
Loaded
Pin

— 11 —

HOW TO ATTACH THE LEG PULLEY ACCESSORY KIT

(b) Take hold of the Vertical Column and pull it up until it is upright.
Release the Spring Loaded Pin. You should hear it lock back into
place.

Leg Pulley Accessory Kit
Rope

IMPORTANT: Be sure the Spring Loaded Pin is locked into
place before using your unit. You will know the pin is
locked into place when you can see the end protrude
through the inside of the rail bracket.

Pulley/D-Ring
Assembly
Clip

Pulley
Harness
Clip

Leg Pulley Bracket

Large
Hitch
Pin

6.

For use with leg pulley
accessory only.

Fig. 1

1.

Connect the Leg Pulley Bracket to the top of the Vertical Column by
aligning Bracket with the hole at the top of the column. (Be sure
bracket is right side up.) Insert Large Hitch Pin through the hole to
secure Bracket onto the Vertical Column (See Fig. 1).

2.

Detach the Cable Assembly from the loop on the underside of the
glideboard and attach one of the Clips from the Leg Pulley Assembly.

3.

4.

5.

Attach the Foot Harness to one of your feet by placing your foot in
the Harness so the sewn-in-ring is on the bottom of your foot.
Pull tightly on the belt so the Harness is secure.(See Fig. 3)
(a) Position yourself on the glideboard correctly for the specific
exercise you want to perform.
(b) While lying down on the glideboard, connect the Clip on
the end of the rope to an O-Ring on the Harness attached
to your foot.(See Fig 4.) Depending on the exercise you are
performing, connect the Clip to the proper O-Ring. Be sure to
always stabilize the glideboard when clipping the Harness on or
off. Also, use caution when getting on or off the glideboard. You
are now ready to exercise using the Leg Pulley Accessory.
See your Exercise Guide for specific exercises that utilize the
Leg Pulley Accessory.

7.

7.

Bracket
D-Ring
Pulley

Push the pin down into its locked position (it should lay flat against
the height adjustment column).
Never sit on or exercise on the unit without the height
adjustment “C” pin securely locked into place.

Fig. 2

Fig. 3

O-Ring (loose)

NOTE: Insert Safety Hitch Pin in the side hole located
at the bottom of the Vertical Column.
(This is the pin you removed in step 5a).

Harness
Buckle
Foot Harness
O-Ring (sewn in)

Fig. 4

NOTE: Remove Leg Pulley Bracket when you are not exercising with it.
(c) To disconnect the Harness, unclip the rope from the O-Ring on
the Harness. Be sure to stabilize glideboard when disconnecting Foot Harness.

— 10 —

6a.

6b.

Large Hitch Pin

Place D-Ring on Pulley first. Then connect the D-Ring to the
Bracket as shown.(See Fig. 2)

NOTE: If rope appears to be twisted, take D-Ring off and turn
Pulley around.

Pull Vertical
Column Up

Release
spring
loaded pin

(a) Position one foot on back crossbar to keep the product from lifting
off the floor. With one hand on either the right or left rail and the other
hand holding the height adjustment “C” pin, slide the rails up along the
height adjustment column. Line up the hole to the first (lowest) position
on the height adjustment column.
(b) Insert height adjustment “C” pin
from the back as shown.

Bracket

5b.

O-Ring (loose)

Clip

STOPPER ASSEMBLY
8.

If the Stopper at the bottom of the Vertical Column has not already
been installed, please do so now. Locate the Stopper which is packed
in the Leg Pully Kit (See Product Specifications on page 5 of this
manual). Unscrew nut on the end of the Stopper and remove. Insert
the Stopper into the hole located in the center of the Back Crossbar.
(See Fig. 1) Screw the nut back onto the Stopper and tighten with
Allen Wrenches provided. (See Fig. 2)
IMPORTANT: Proper installation of the Stopper is necessary
for the Rollers to function easily when the unit is folded and
rolled into place for storage.

— 7 —

8.

Fig. 1

Fig. 2

HOW TO ATTACH THE MULTI FUNCTION ATTACHMENT

FRONT PRESS

The multi function attachment provided with your unit has been uniquely designed to serve several
purposes. It can be placed at the top or bottom of the exerciser and angled toward you or away from
you depending upon what is comfortable for you.
Two thick foam pads are provided with the multi function attachment. They must be attached to the
attachment (if not already) before exercising. To do this:
1.

2.

Simply wet each end of the straight crossbar of the
attachment with some soapy water.

1.

Locate the holes at the bottom of the right and left rails near
the front crossbar.

2.

With the attachment toward the glideboard, line up the
brackets on the attachment with the desired position
holes on the rails.

3.

Insert the 2 large hitch pins through the holes on the attachment
brackets and the hole on the rails, as shown in Figure 4.

4.

You are now ready to perform the front press which works the
upper chest and triceps. See your Exercise Booklet for specific exercises.

Fig. 1

Attach foam pads on the crossbar as shown
in Figure 1. Let dry before beginning to exercise
with the multi function attachment.

SQUATS
1.

Locate the holes at the bottom of the right and left rails
near the front crossbar.

2.

With the attachment angled away from the glideboard, line up
the brackets on the attachment with the desired position holes
on the rails.

3.

Insert the 2 large hitch pins through the holes on the attachment
brackets and the hole on the rails, as shown in Figure 5.

4.

You are now ready to perform the front press which works the thighs
and calves. See your Exercise Booklet for specific exercises.

Proper ways to use the multi function attachment in accordance
with the exercises you wish to do:

PULL UPS
1.

2.

Fig. 2

Locate the holes at the top of the right and left rails on the
column end of the unit.
With the attachment angled toward the glideboard, line up
the brackets on the attachment with the desired position
holes on the rails.

3.

Insert the 2 large hitch pins through the holes on the
multi function attachment brackets and the hole on the
rails, as shown in Figure 2.

4.

You are now ready to perform pull up and chin up exercises to
work the arms, lats and back. See your Exercise Booklet for
specific exercises.

NOTE: When performing the squat exercises, be sure to position
your hands on the side of the glideboard, NOT along the
bottom of the board in order to avoid pinched fingers.

LEG PULL: CRUNCHES, LEGS AND SIT UPS
1.

Locate the holes at the top of the right and left rails on the
column end of the unit.

2.

With the attachment angled away from the glideboard, line
up the brackets on the attachment with the desired position
holes on the rails.

3.

Insert the 2 large hitch pins through the holes on the
multi function attachment brackets and the hole on the
rails, as shown in Figure 3.

4.

You are now ready to perform leg pulls, crunches and sit up
exercises to work the abdominals, waist and legs. See your
Exercise Booklet for specific exercises.

— 8 —

Fig. 4

Fig. 3

— 9 —

Fig. 5



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2004:09:01 21:10:05Z
Modify Date                     : 2005:04:08 18:00:00-04:00
Page Count                      : 7
Creation Date                   : 2004:09:01 21:10:05Z
Mod Date                        : 2005:04:08 18:00:00-04:00
Producer                        : Acrobat Distiller 5.0.5 for Macintosh
Author                          : Margaret
Metadata Date                   : 2005:04:08 18:00:00-04:00
Creator                         : Margaret
Title                           : TG1700 Club OWNERS GUIDE
EXIF Metadata provided by EXIF.tools

Navigation menu