Flextronics UMPC8187B UMPC User Manual UM650UV1 User Menual Revised 04

Flextronics International (Taiwan) Ltd. UMPC UM650UV1 User Menual Revised 04

User Manual

ʳʳʳʳʳʳʳʳʳʳʳʳUltra Mobile PCUser's GuideModel: UM650UV1First Edition: January 2007
User's Guide Page II Specifications and information found in this guide are subject to change without notice. Any changes therefore will be incorporated in future editions. The manufacturer assumes no responsibility for errors or omissions in this document. Windows™ is the trademark of Microsoft Corporation.Bluetooth® is the trademark owned by its proprietor. Other trademarks are properties of their respective owners. NOTICETRADEMARKS
User's Guide Page III The following standards are adopted throughout this guide: Notebook in boldface (with or without capitalization) refers to the notebook computer that you have purchased. Boldface type is also used to highlight important information in this document. Whenever extra caution is called for, the information will be boxed in a dark frame preceded by "Note:" or "Warning:"Standards
User's Guide Page IV This page is left blank intentionally.
User’s Guide Contents Page V CHAPTER 1 BEFORE YOU BEGIN ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ ˄ˀ˄1.1 CHECKING WHAT YOU RECEIVEDˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˄ˀ˄1.2 EXAMINING YOUR COMPUTERˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˄ˀ˅1.3 THE FIVE SYSTEM LEDSˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˄ˀˋ1.4 THE THREE CONTROL SWITCHESˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˄ˀˌ1.5 THE SIX SYSTEM BUTTONS ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˄ˀ˄˃1.6 THE FOUR COMMUNICATION BUTTONS ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˄ˀ˄˄1.7 ATTENTION ONMEDIA CARD SLOT ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˄ˀ˄ˆ1.8 TOUCH SCREEN CALIBRATIONˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˄ˀ˄ˇ1.9 OPERATING TEMPERATUREˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˄ˀ˄ˇCHAPTER 2 BATTERY ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ ˅ˀ˄2.1 BATTERY PACK ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˅ˀ˄2.2 RECHARGING THE BATTERY PACKˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˅ˀ˄2.3 QUESTIONS AND ANSWERSˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˅ˀ˅2.4 BATTERY MAINTENANCE ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˅ˀˆ2.5 POWER CONSUMPTIONˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˅ˀˆ2.6 REDUCING POWER CONSUMPTIONˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˅ˀˇ2.7 REMOVING THE BATTERY PACKˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˅ˀˇ2.8 CONNECTING SYSTEM TOAC ADAPTER ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ˅ˀˈCHAPTER 3 THE DOCKING STATION (OPTIONAL) ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ ˆˀ˄3.1 DIFFERENT VIEWS OFTHE DOCKING STATIONˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˆˀ˄3.2 MOUNTING THE DETACHABLE STANDˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˆˀˈ3.3 MOUNTING THE SYSTEM UNIT ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˆˀˉ3.4 THE STYLUS PENˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˆˀˊCHAPTER 4 THE BAY MODULE CONNECTORˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ ˇˀ˄4.1 REMOVING THE FLIP STAND ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˇˀ˅4.2 THE BAY MODULESˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˇˀˆCONTENTS
Contents User's GuidePage VI 4.3 INSTALLING THE BAY MODULE ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˇˀˇ4.4 THE GPS MODULE ANTENNAˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˇˀˈ4.5 THE TV TUNER MODULE ANTENNA ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˇˀˉAPPENDIX A- AGENCY REGULATORY NOTICES ˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁˁ ˔ˀ˄
User's Guide Before You Begin Page 1-1 Chapter 1 Before You BeginPlease read this section before you start using your Ultra Mobile PC.1.1 Checking What You ReceivedYour Ultra Mobile PC package should contain the following items: ʳx The Ultra Mobile PC.x AC Adapter. x AC Power Cord. x CD Disc (Including Drivers and User’s Guide). x Battery Pack. x TV Module with Antenna (Option). x GPS Module with Antenna (Option). x Docking Station (Option). Note: You should keep the original factory carton and packing materials in case you need to ship the unit back for servicing.
Before You Begin User's GuidePage 1-2 1.2 Examining Your Computer Before you start using your computer, you need to get acquainted with its main features and interfaces: Panoramic View Slide the display panel to open up keyboard before you operate.
User's Guide Before You Begin Page 1-3 Top ViewWeb Cam Five System LEDs Two Internal Microphones Six System Buttons LCD Screen Four Communication ButtonsTouch Pad Keyboard ʳʳʳʳʳʳʳ
Before You Begin User's GuidePage 1-4 Bottom ViewSupport Foot (also serves to lock and to disassemble the Flip Stand) Battery Pack Ventilation Holes Flip Stand Speaker Stylus Slot Note: The stylus pen together with the system touch-screen LCD display provides you a touch-screen operation by emulating the industry standard mouse left click. You are advised to keep the stylus pen in the stylus slot when not in use. ʳʳʳʳ
User's Guide Before You Begin Page 1-5 Front ViewConnector for Docking Station USB Connector VGA Connector Rear ViewKensington Lock Ventilation Holes ʳ
Before You Begin User's GuidePage 1-6 Left ViewBattery Lock Media Card Slot (SD/ SD-IO/ MMC) Battery Latch Battery Pack USB Connector
User's Guide Before You Begin Page 1-7 Right ViewMicrophone Jack Battery Pack Power/Hold Switch The SAS (Alt+Ctrl+Del) Switch Volume (Increase/Decrease) Switch Headphone Jack Stylus Slot DC-In Jack Two Types of Audio JackʳʳMono Jack:Your microphone jackshould have this type ofconnector as shown here.Stereo Jack:Your headphone jack should have this type of connector as shown here ʳ
Before You Begin User's GuidePage 1-8 1.3 The Five System LEDsThe Bluetooth® LEDThis LED would be lit when the Bluetooth® is powered on. For details on how to power on and power off the Bluetooth, please refer to Chapter 1.6.ʳThe Wireless LAN LEDThis LED would be lit when the Wireless LAN is powered on. For details on how to power on and power off the Wireless LAN, please refer to Chapter 1.6.ʳThe HDD Access LEDThis LED would be lit when system is accessing the HDD drive.ʳThe Battery Pack LEDBelow is how the LED would behave in different situations:On Battery pack is being recharged: fast-charge or pre-charge. Off Battery pack is not under recharge. Blinking Battery pack is consuming down to 10% level. The Power On LEDBelow is how the LED would behave in different situations:OffSystem is powered off, or in Hibernate mode. On System is in full operation. Blinking System is in Standby mode. Note: The Five System LEDs are located near the bottom of display panel. For exact location, please refer to the Top View diagram in Chapter 1.2.For more details on Standby and Hibernate, please refer to Power Options in the Control Panel of your Microsoft Windows™ operating system.
User's Guide Before You Begin Page 1-9 1.4 The Three Control Switches ʳThe SAS (Alt+Ctrl+Del) Switch Press this switch to emulate Windows’ “Alt”, “Ctrl” and “Del” buttons pressed simultaneously. ʳThe Power/Hold SwitchSlide this switch to the right ( ) to emulate standard power button of a personal computer. The power button is programmable by user. For details on how to program the power button, please refer to the Power Options of Control Panelin Windows™ System. Slide this switch to the left (HOLD) to temporarily suspend inputs from the keyboard,touch pad,six system buttons on the left side of the LCD screen, and the four communication buttons in between the left/right keyboard. Manually slide this switch back to the middle to resume functions of the above input devices. The purpose of this switch is to prevent mis-triggering of these input devices while the system unit is idle when it is powered up. For exact locations of these input devices, please refer to Top View diagram in Chapter1.2.ʳThe Volume SwitchClick this switch to the right (壊) to increase audio volume. Click this switch to the left (壇) to decrease audio volume.Note: The Three Control Switches is located on the right side of system unit. For exact location, please refer to the Right View diagram in Chapter 1.2.
Before You Begin User's GuidePage 1-10 1.5 The Six System Buttons ʳThe Mobility Center Button Press this button to enter into the menu of Windows Mobility Center in Windows Vista™ operating system. The Zoom-In ButtonPress this button to activate the zoom-in function whereby portion of the display screen near the mouse cursor would be enlarged and displayed near the topside of the display screen. ʳThe Enter ButtonPress this button to emulate the function of “Enter”. The Scroll ButtonPress this button to emulate the functions of these four “m”, “o”, “n”, and “p”keycaps. ʳThe Left Mouse ButtonPress this button to emulate the left mouse function. ʳThe Right Mouse ButtonPress this button to emulate the right mouse function. Note: The Six System Buttons are located on the left side of the LCD display. For exact location, please refer to the Top View diagram in Chapter 1.2.
User's Guide Before You Begin Page 1-11 1.6 The Four Communication Buttons ʳThe Bluetooth ButtonPress this button to power on and power off the Bluetooth® module. Powering on the Bluetooth® by pressing this button does not automatically activate the Bluetooth® function. After powering on, you need to activate the Bluetooth®function through Windows™. The main purpose of this button is to provide you a quick way to turn off the power of Bluetooth® when entering venues like airplanes, airports, and hospitals where the usage of Bluetooth® is prohibited or not advisable.ʳThe Wireless LAN ButtonPress this button to power on and power off the Wireless LAN module. Powering on the Wireless LAN by pressing this button does not automatically activate the Wireless LAN function. After powering on, you need to activate the Wireless LAN function through Windows™. The main purpose of this button is to provide you a quick way to turn off the power of Wireless LAN when entering venues like airplanes, airports, and hospitals where the usage of Wireless LAN is prohibited or not advisable. ʳThe Web Cam ButtonPress this button to power on and power off the Web Cam module. After powering on the Web Cam, you need to activate its function through Windows™.ʳThe BAY Button Press this button to power on and power off the GPS Module or TV Tuner Module. Powering on the GPS Module or TV Tuner Module by pressing this button does not automatically activate the respective functions. After powering on, you need to activate the function through Windows™. This button would work only when the system is powered on, and either one of the GPS or TVTuner Module is connected into the system unit. Note:GPS and TV Tuner Modules are optional and need to be purchased separately. For details on how to connect these modules to the system unit, please refer to Chapter 4.
Before You Begin User's GuidePage 1-12 Note: The proper way to activate the above devices and modules is as below: 1) Press the above buttons to power on the devices, and modules. 2) Activate the respective application programs in Windows™. The effective range of the system Bluetooth® is 10 meters. Note: The Four Communication Buttons are located between the left/right keyboards. For exact location, please refer to the Top View diagram in Chapter 1.2.
User's Guide Before You Begin Page 1-13 1.7 Attention On Media Card Slot ʳʳʳʳPlease observe below safety measures: x When no card (SD/SD-IO/ MMC cards) is inserted into the media slot, make sure this slot is covered by the “media slot door” as supplied together with this Ultra Mobile PC. The purpose of this “media slot door” is to prevent foreign matters from entering into the system unit through this slot, when no card is inserted. When inserting this “media slot door”, please make sure the arrow is on the topside as shown above. Inserting this door upside down may cause damage to your Ultra Mobile PC.Media Slot Door is now inserted into the system unit.Arrow on topside of Media Slot Door. The Media Slot Door is now taken out from the system unit.
Before You Begin User's GuidePage 1-14 1.8 Touch Screen Calibration The stylus pen together with the system touch-screen LCD display provides you a touch-screen operation by emulating the industry standard mouse left click. Below are the two conditions that you need to calibrate your touch-screen. x The first time Windows is installed and boot up. The active cursor is shifted; not exactly the same position where the stylus pen tip is tapped. x Periodically when you find the active cursor is shifted away from the screen position where the stylus pen tip is tapped. To calibrate the touch-screen, go into Tablet PC Setting of Control Panel of Windows™VISTA®. In the Tablet PC Setting screen, select General and then Calibrate. Then follow instruction to complete calibration. Note: You need to set screen display resolution to 800x600 before proceeding with the calibration. 1.9 Operating Temperature Operating Temperature : 10ºC to 35ºC.
User's Guide Battery Page 2-1 Chapter 2 Battery2.1 Battery PackYour Ultra Mobile PC is equipped with a high-energy rechargeable Lithium Ion (Li-Ion)battery pack. Battery life will vary depending on the product configuration, product model, applications loaded on the product, power management settings of the product, and the product features used by the customer. As with all batteries, the maximum capacity of this battery will decrease with time and usage. 2.2 Recharging The Battery Pack Your Ultra Mobile PC supports both on-line and off-line recharge. Follow the procedure below to recharge battery: x Make sure the battery pack is installed in the Ultra Mobile PC.x Connect the AC adapter to the Ultra Mobile PC and to an electrical outlet. When a battery pack is being recharged, its battery LED (located at the bottom of LCD display) would be lit. For details on the LEDs, please refer to Chapter 1.3. When the UltraMobile PC is OFF, a depleted Li-Ion battery will take three hours to recharge.
Battery User's GuidePage 2-2 2.3 Questions And Answers Q: I can feel a mild heat next to the battery pack. Is it normal? A: The battery will generate heat during recharging and discharging. There is a protection circuit inside the Ultra Mobile PC to prevent overheating. User needs not to worry. Q: My battery operation time is not as long as it should be. Why? A: The battery is heat sensitive and can only be charged to its maximum if the battery and its environmental temperature remain within 15-25qC (59-77qF). The more the temperature deviates from this range during recharging, the less chance there is for the battery to be fully charged. In order to recharge the pack to its full capacity, users are requested to cool down the unit by unplugging the AC Adapter. Wait until it is cooled down. Then plug in the AC Adapter to start recharging again.Q: I did not use my spare battery for a few days. Even though it was fully recharged, there wasn't as much power left as a newly charged one. Why? A: The batteries will self-discharge (1% per day for Li-Ion) when they are not being recharged. To make sure a battery pack is fully charged, recharge before use. Always keep the battery inside the Ultra Mobile PC and have the AC adapter connected whenever possible.Q: I did not use my spare battery for months. I have problem in recharging it. A: If you happen to leave your battery pack to go through an extended period of self-discharge, say more than three months, the battery voltage level will become too low and needs to be Pre-Charged (to bring the battery voltage level high enough) before it automatically (for Li-Ion only) resumes its normal Fast Charge.Pre-Charge may take 30 minutes. Fast Charge usually takes 2~3 hours.
User's Guide Battery Page 2-3 2.4 Battery Maintenance To maintain the battery pack's maximum capacity, you should occasionally let the UltraMobile PC deplete its battery power completely before recharging. To carry out a complete depletion of the battery, disconnect the AC adapter and let your Ultra Mobile PC consume the remaining battery power. To speed up the depletion, use the HDD as much as possible. When the battery is empty, wait for the Ultra Mobile PC to cool down (especially the battery). The temperature should be within 15-25qC (59-77qF).Then insert the AC adapter to recharge the battery. 2.5 Power ConsumptionThe Windows™ operating system has incorporated the latest state-of-the-art ACPI(Advanced Configuration Power Interface) power management methodology. In order to fully utilize the power of your battery packs, it would be a good idea for you to spend sometime to acquire a basic understanding of the power management concept from your operating system. In Windows™ Operating Systems, you can go through Power Options of the ControlPanel according to the version of Windows™ Operating System the Ultra Mobile PCapplies. We shall not describe them in details.
Battery User's GuidePage 2-4 2.6 Reducing Power Consumption Although your Ultra Mobile PC (together with the operating system) is capable of power conservation, there are measures you can take to reduce the power consumption: x Use the AC power whenever possible.x Try to use the HDD drive to read and write files, instead of using the external USB FDD. x Disable unused devices, such as Web Cam, WLAN, Bluetooth®, and etc. x Decrease LCD panel brightness through Windows. Note: Whenever system is powered on or powered off, make sure the battery pack is installed in the battery pack compartment. 2.7 Removing The Battery Pack This battery pack can easily be removed and replaced. Make sure that the computer is properly shutdown before changing the battery pack. If you would like to change the battery pack while power is on, make sure this battery pack is not the only electrical source to the system unit. Follow the steps below to remove the battery pack. ʳx Make sure the system is properly shutdown. x Flip the system upside down as shown. x Push the battery lock to the unlock position as shown by #1.x Push the battery latch to the unlock position as shown by #2.x Remove the battery pack as shown by #3.To insert the battery pack, reverse the steps above.
User's Guide Battery Page 2-5 2.8 Connecting System To AC Adapter x Connect AC adapter to system unit as shown by #1.x Connect AC power cord to AC adapter as shown by #2.x Connect other end of power cord to an electrical outlet as shown by #3.
Battery User's GuidePage 2-6 This page is left blank intentionally. ʳ
User's Guide The Docking Station (Optional) Page 3-1 Chapter 3 The Docking Station (Optional)Depending on model, your Ultra Mobile Personal Computer is equipped with an optional Docking Station. This Docking Station does not support hot plug-and-play with the system unit. 3.1 Different Views Of The Docking Station Panoramic View Power Button Detachable Stand Connector to System Unit ʳʳ
The Docking Station (Optional) User's GuidePage 3-2 ʳNote: This Power Button has the same function as the Power Switch as described in Chapter 1.4. For details, please refer to Chapter 1.4.The Detachable Stand is shipped not mounted to the main body of the DockingStation as shown above. For details on how to mount this Detachable Stand,please refer to Chapter 3.2.Front View Power Button Detachable Stand ʳ
User's Guide The Docking Station (Optional) Page 3-3 Right View Stylus Pen IEEE 1394 Connector Stylus Pen Tray (push to eject) USB Connector ʳ
The Docking Station (Optional) User's GuidePage 3-4 Rear ViewHeadphone Jack DC-In Jack USB Connectors VGA Connector RJ45 LAN Connector ʳʳ
User's Guide The Docking Station (Optional) Page 3-5 3.2 Mounting The Detachable Stand x Align and lock the tenon from detachablestand to the mortise from the docking stationas shown by #1.x Slide the right side of the detachable stand in the direction as shown by #2.x Gently press the detachable stand to the docking station as shown. Reverse the above steps to un-mount the detachable stand.
The Docking Station (Optional) User's GuidePage 3-6 3.3 Mounting The System Unit x Make sure connectors from both sides are well aligned.x Slide the system unit down as shown.x System unit is mounted when the two connectors are full engaged as shown.Reverse the above steps to un-mount the system unit.
User's Guide The Docking Station (Optional) Page 3-7 3.4 The Stylus Pen The stylus pen can be taken out and erected as shown below: x Press on the Stylus Pen Tray in the direction as shown.x The Tray would slide out as shown.x The Tray has an insertion hole where you can erect the Stylus Pan as shown.
The Docking Station (Optional) User's GuidePage 3-8 This page is left blank intentionally.
User's Guide The BAY Module Connector Page 4-1 Chapter 4 The BAY Module Connector This Ultra Mobile PC has a BAY Module Connector whereby by you can either choose to connect it to a GPS (Global Positioning System) Module, or a TV Tuner Module. Both the GPS Module and TV Tuner Module are optional and need to be purchased separately. The BAY Module Connector is underneath the flip stand. Diagram below shows the bottom view of the system unit with the flip stand removed. ʳThe rest of this chapter describes how the flip stand is removed and how the GPS Moduleand TV Tuner Module are installed to the system unit. The BAY Module Connector
The BAY Module Connector User's GuidePage 4-2 4.1 Removing The Flip Stand x Gently flip the flip stand to an almost erect angle as shown.x Press and slide the support foot in the direction as shown by #1.x Remove the flip stand as shown by #2.ʳReverse the steps above to put back the flip stand.
User's Guide The BAY Module Connector Page 4-3 4.2 The BAY Modules Externally, the GPS Module and TV Tuner Module looked very much the same as shown below. ʳʳʳʳʳʳx The external side of the BAY Module when it is installed to the system unit. ʳʳʳʳʳx The internal side of the BAYModule when it is installed to the system unit.Connect to system Connect to antenna The two tenons are used for locking module to system unit.
The BAY Module Connector User's GuidePage 4-4 4.3 Installing The BAY Module ʳx Align and lock the tenon from the module to the mortise from the system unit as shown by #1.x Slide support foot in the direction as shown by #2.x Gently press on the back of the connector to connect module as shown by #3.ʳʳx The support foot would slide back by itself in the direction as shown. The module is locked to the system unit.ʳʳReverse the above steps to remove the BAY Module.
User's Guide The BAY Module Connector Page 4-5 4.4 The GPS Module Antenna The GPS Module has a built-in internal antenna. For better receptions and transmissions, it is better to use its proprietary external antenna as shown below. ʳʳx Connect external antenna to the GPS Module.ʳʳ
The BAY Module Connector User's GuidePage 4-6 4.5 The TV Tuner Module Antenna The earlier version of the TV Tuner Module is without a built-in internal antenna. Therefore, it is necessary to use its proprietary external antenna as shown below. The later version of the TV Tuner Module is with built-in internal antenna. However for better receptions and transmissions, it is better to use its proprietary external antenna as shown below. ʳʳʳx Connect external antenna to the TV Tuner Module.ʳ
User’s Guide Appendix APage A-1 Appendix A- Agency Regulatory Notices A.1 Safety Instructions CAUTION: Please read these safety instructions carefully. CAUTION: Please keep this User's Manual for future reference. CAUTION: Please disconnect this equipment from AC outlet before cleaning. DO NOT use liquid or sprayed detergent for cleaning. Use a clean moistened cloth. CAUTION: The wall socket used should be positioned near the equipment and should be easily accessible. CAUTION: Please keep this equipment free from humidity. CAUTION: Place the equipment on a reliable surface at all times. A drop or fall can cause severe damage. WARNING: The openings of the enclosure are for air ventilation and are meant to protect the equipment from overheating. DO NOT COVER THE VENTILATION OPENINGS.
Appendix A User's GuidePage A-2 CAUTION: Verify the voltage of the power source before connecting the unit to any power outlet. WARNING: DO NOT step on or place anything over the power cord. CAUTION: All cautions and warnings on the equipment should be noted. WARNING: If the equipment is not used for a long period of time, disconnect the equipment from the power source to avoid damage from power spikes.WARNING: NEVER pour any liquid into any openings; a fire or electrical shock is possible. WARNING: For safety reasons, other than pre-designated ports, doors, and the equipment should be opened only through qualified service personnel. CAUTION: If one of the following situations should arise, the equipment should be checked by an authorized technician: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to excessive moisture. d. The equipment does not work well, or you fail to get it to work according to user's manual. e. The equipment has been dropped or damaged. f. The equipment has obvious signs of breakage.
User’s Guide Appendix APage A-3 CAUTION: DO NOT LEAVE THE EQUIPMENT IN TEMPERATURES BELOW -20ºC(-4ºF) OR ABOVE 60ºC(140ºF). IT MAY CAUSE DAMAGE TO THE EQUIPMENT. WARNING: Never install modem/telephone wiring during a lightning storm. WARNING: Never install modem/telephone jacks in wet locations unless the jack is specially designed for wet locations. WARNING: Never touch un-insulated modem/telephone wires or terminals unless the modem/telephone line has been disconnected at the network interface.CAUTION: Use caution when installing or modifying modem/telephone lines. WARNING: Avoid using a modem/telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. WARNING: This computer contains an internal lithium battery-powered real-time circuit. There is a risk of explosion and injury if the battery is incorrectly replaced or handled. Do not attempt to recharge, disassembled, immerse in water, or dispose of it in fire. Replacement should be done through your notebook dealer.
Appendix A User's GuidePage A-4 WARNING: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’̆ instructions. Explosionsgefahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. WARNING: Your UMPC contains a Ni-MH or Li-Ion battery pack. There is a risk of fire and chemical burn if the battery pack is handled improperly. Do not disassemble, crush, puncture, short external contact, dispose of in water or fire, or expose it to temperature higher than 60ºC.WARNING: Handle the battery pack very carefully. Avoid touching the metal leads on the connector of the battery case. CAUTION: Use only approved AC Adapter with your notebook. Using the wrong type of AC Adapter may cause serious damage to your notebook. CAUTION: The AC Adapter can accept a line voltage ranging from 100V to 240V and is compatible with most international power sources. If you are unsure whether your power source is compatible, please contact the local dealer for assistance. CAUTION: For Continued Protection Against Risk of Fire, Replace Only with same Type and Rating of Fuse.CAUTION: If the computer is not sold to German area, please use only the local recognized power supply cords that are recommended by the manufacturer.
User’s Guide Appendix APage A-5 WARNING: Don't expose your UMPC to excessive heat or coldness (frost). Don't drop, spill fluids or open the exterior of the case. This can damage the UMPC and void the warranty.
Appendix A User's GuidePage A-6 A.2 Agency Notice Federal Communications Commission NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: x Reorient or relocate the receiving antenna. x Increase the separation between the equipment and receiver. x Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. x Consult the dealer or an experienced radio or television technician for help. ModificationsThe FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by the manufacturer responsible for compliance may void the user’s authority to operate the equipment. CablesConnections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain compliance with FCC Rules and Regulations. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
User’s Guide Appendix APage A-7 FCC RF Radiation Exposure Statementx This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. USA and Canada Safety Requirements And NoticesThe FCC with its action in ET Docket 93-62 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified equipment. The Intel PRO/Wireless LAN MiniPCI Adapter products meet the Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC’s recommended limits. The following safety precautions should be observed: x Do not touch or move antenna while the unit is transmitting or receiving. x Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face or eyes, while transmitting. x Do not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged. Use in specific environments: x The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such environments. x The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA). x The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. Explosive Device Proximity WarningWarning: Do not operate a portable transmitter (such as a wireless network device) near unshielded blasting caps or in an explosive environment unless the device has been modified to be qualified for such use. Use On Aircraft CautionCaution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments.
Appendix A User's GuidePage A-8 Canadian NoticeThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Avis CanadienCet appareil numerque de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada. Canada Radio Frequency Interference RequirementsThis Class B digital apparatus complies with Canadian ICES-003, Issue 2, and RSS-210, Issue 4 (Dec. 2000). “To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.” Cet appareil numérique de la classe B est conforme à la norme NMB-003, No. 2, et CNR-210, No. 4 (Dec. 2000). “Pour empêcher que cet appareil cause du brouillage au service faisant l’objet d’une licence, il doit être utilizé à l’intérieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal. Si le matériel (ou son antenne d’émission) est installé à l’extérieur, il doit faire l’objet d’une licence.” European Union NoticeProduct with the CE Marking comply with the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community and if this product has telecommunication functionality, the R&TTE Directive (1999/5/EC). Compliance with these directives implies conformity to the following European Norms (in parentheses are the equivalent international standards and regulations): x EN55022 (CISPR 22) Electromagnetic Interference x EN55024 (IEC61000-4-2,3,4,5,6,8,11) Electromagnetic Immunity x EN61000-3-2 (IEC61000-3-2)-Power Line Harmonics x EN61000-3-3 (IEC61000-3-3)-Power Line Flicker x EN60950 (IEC60950)  Product Safety
User’s Guide Appendix APage A-9 For devices with built-in wireless equipment, the following additional standards apply: x ETSI301489-17: General Emissions for Radio Equipment x EN60950: Safety x ETSI300328-2: Technical Requirements for Radio Equipment CE Caution: Due to the fact that the frequencies used by 802.11b/802.11g wireless LAN devices may not yet be harmonized in all countries, 802.11b/802.11g products are designed for use only in specific countries or regions, and are not allowed to be operated in countries or regions other than those of designated use. As a user of these products, you are responsible for ensuring that the products are used only in the countries or regions for which they were intended and for verifying that they are configured with the correct selection of frequency and channel for the country or region of use. And deviation from permissible settings and restrictions in the country or region of use could be an infringement of local law and may be punished as such. The wireless LAN device can currently be used indoors only in the following departments of mainland France. 01 Ain 36 Indre 69 Rhône02 Aisne 37 Indre et Loire 70 Haute Saône 03 Allier 39 Jura 71 Saône et Loire 05 Hautes Alpes 41 Loir et Cher 72 Sarthe08 Ardennes 42 Loire 75 Paris09 Ariège 45 Loiret 77 Seine et Marne 10 Aube 50 Manche 78 Yvelines 11 Aude 54 Meurthe et Moselle 79 Deux Sèvres 12 Aveyron 55 Meuse 82 Tarn et Garonne 16 Charente 57 Moselle 84 Vaucluse19 Corrèze 58 Nièvre 86 Vienne2A Corse Sud 59 Nord 88 Vosges2B Haute Corse 60 Oise 89 Yonne 21 Côte d’Or 61 Orne 90 Territoire de Belfort 24 Dordogne 63 Puy du Dôme 91 Essonne25 Doubs 64 Pyrénées Atlantique 92 Hauts de Seine 26 Drôme 65 Haute Pyrénées 93 Seine St Denis 27 Eure 66 Pyrénées Orientales 94 Val de Marne 32 Gers 67 Bas Rhin 35 Ille et Vilaine 68 Haut Rhin The wireless LAN device cannot currently be used in any departments of mainland France other than those listed above.
Appendix A User's GuidePage A-10 Maximum allowable EIRP 802.11b wireless LAN cards in the mainland departments of France not shown in the table above are as follows: (See the ART website at www.art-telecom.fr for information on the French overseas territories.) Frequency Ranges (MHz) Indoors Outdoors 2400 – 2446.5 10 mW Not permitted 2446.5 – 2483.5 100 mW 100 mW on private property with Ministry of Defense approvalJapanese NoticeDGT Statementʳ ʳʳ
User’s Guide Appendix APage A-11 U.S. Regulations Governing the Use of ModemsThis equipment complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company. If your telephone equipment harms the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify in advance. But, if advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a compliant with the FCC. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect proper operation of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. The FCC prohibits this equipment to be connected to party lines or coin-telephone service. In the event that this equipment should fail to operate properly, disconnect the equipment from the phone line to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or vendor. The FCC also requires the transmitter of a FAX transmission be properly identified (per FCC Rules Part 68, Sec 68.381 (C) (3)). Japanese Modem NoticeU.K. Modem Compliance InformationThis modem is approved by the secretary of state at the Department of Trade and Industry for connection to a single exchange line of the public switched telephone network run by certain licensed public telecommunication operators or system connected there to (Direct exchange lines only, not shared service or 1-1 carrier systems).
Appendix A User's GuidePage A-12 This modem is also suitable for connection to Private Automatic Branch Exchange (PABX),which return secondary proceeding indication. If this modem is to be used with a PBX which has extension wiring owned by BT, connection of the modem the PBX can only be carried out by BT; or by the authorized maintainer of the PBX unless the authorized maintainer has been given 14 days written notice that the connection is to be made by another person; and that period of notification has expired. This modem is suitable for use only on telephone lines proved with Loop Disconnect or Multi-Frequency Dialing Facilities. Users of this modem are advised that the approval is for connection to the PSTN via the telephone line interface supplied with it. Connection of a modem to the PSTN by any other means will invalidate the approval. There is no guarantee of correct working in all circumstances. Any difficulties should be referred to your supplier. Some network operators require that intended users of their network request permission to connect and for the installation of an appropriate socket. The Ringer Equivalence Number (REN) of this modem is 1. REN is guide to the maximum number of apparatus that can simultaneously be connected to one telephone line. The REN value of each apparatus is added together, and should not exceed 4. Unless otherwise marked, a telephone is assumed to have a REN of 1. This modem is only approved for use of the following facilities: x Storage of telephone numbers for retrieval by a predator mined code. x Initial proceed indication detection. x Automatic calling / automatic answering. x Tone detection. x Loud-speaking facility. This modem is not approved for connection to U.K./private speech-band services. This modem does not support an automatic re-dial function. Any other usage will invalidate the approval of your modem, if as a result, it then ceases to confirm to the standards against which approval was granted. The approval of this modem is invalidated if the apparatus is subject to modification in any material way not authorized by the BABT or if it is used with, or connected to external software that have not been formally accepted by BABT.ʳ

Navigation menu