Flir BelgiumBA 24DD4KW Light Marine Navigational Radar User Manual
Raymarine UK Ltd. Light Marine Navigational Radar
Contents
- 1. user guide
- 2. installation guide
- 3. operating guide
operating guide
E-Series Display Operating Guide www.raymarine.com PAGE ACTIVE WPTS MOB DATA MENU General Operation OUT RANGE IN OK CANCEL The control panel Using the controls Setting up the display Using CompactFlash cards Card 1 Card 2 Card 3 Card 4 What can I see? Understanding the chart Using the chart Displaying additional information Displaying additional information (continued) Understanding the 3D chart Using the 3D chart Card 5 Card 6 Card 7 Card 8 Card 9 Card 10 Basic Navigation Working with waypoints How do I get to a point? Card 11 Card 12 What is around me? Understanding the radar Avoiding a collision Using MARPA AIS Card 13 Card 14 Card 15 Card 16 Where am I going? Monitoring a course Card 17 What's under the boat? Understanding the fishfinder Using the fishfinder Card 18 Card 19 Monitoring data and engines Viewing video images Navtex and Sirius Weather Data Sirius Weather Data (continued) Autopilot Control Understanding tha digital radar Operating a networked E-Series Display Card 20 Card 20 Card 21 Card 22 Card 23 Card 24 Card 25 D6721_5 Other functions General Operation The control panel Card 1 DATA Press to access ruler, chart vectors, archive & transfer and data bar on/off functions. ACTIVE When multiple windows are open: - Press to select required window. - Press and hold to maximize current window. - Press again to return to multiple windows. PAGE Press to scroll through available pages. Press and hold to select different page set or customise your own layout. PAGE ACTIVE WPTS MOB DATA WPTS/MOB Press to display the waypoint soft keys. Press again to place waypoint at your boat's position. Press and hold to place a Man Overboard (MOB) marker at your current position. Press and hold again to exit MOB. MENU MENU Press to access the set up menus. OUT RANGE IN OK Softkeys Press to select the corresponding function identified by the onscreen label Power Press once to turn ON. Press again to access backlight functions and scanner controls. Press and hold to turn the display OFF. RANGE Press to change the display scale so that a smaller or larger area can be seen on the screen. Chart Card slot Open the cover to install CompactFlash cards. CANCEL Rotary control Use to edit alpha-numeric values, and scroll through lists. Turn clockwise to increase value and counter-clockwise to decrease value. Press to move the cursor to the next character when editing text. Use to edit symbology (VRM/EBL etc). Trackpad Used to control the on-screen cursor and to scroll through menu items. Press the corresponding edge of the trackpad to move the cursor horizontally, vertically or diagonally. Press and hold to move rapidly over larger distances. CANCEL Press to cancel the selected on-screen option when editing data; also used to return to the previous soft key set or menu. OK Press to select an on-screen option, or return to the previous set of soft keys or menu. This unit is only an aid to navigation. Its accuracy can be affected by many factors, including equipment failure or defects, environmental conditions, and improper handling or use. It is the User's responsibility to exercise common prudence and navigational judgements. This unit should not be relied upon as a substitute for such prudence and judgement. Always keep a proper look-out. D7523_2 WARNING: NAVIGATION AID General Operation Using the controls Card 2 How do the controls work? Buttons PAGE Access system functions or change what you see on-screen. Within the text of this document they are written in bold capitals e.g. WPTS/MOB. ACTIVE WPTS/ MOB DATA Press and hold to access short cuts - see individual buttons on facing page. MENU Example: This example shows the series of button and soft key presses required to change the waypoint default symbol or group. Soft keys They change depending on application or function being performed. WAYPOINT AT CURSOR WAYPOINT AT VESSEL WAYPOINT AT LAT/LONG... GO TO WAYPOINT OPTIONS… REVIEW AND EDIT WAYPOINTS ERASE WAYPOINT SORT LIST SET DEFAULT SYM & GROUP... WAYPOINT GROUPS... VIEW AND EDIT DETAILS… Press and hold MENU to display help information for the currently displayed soft keys. Press the corresponding key (below the screen) to select. Further soft keys may be displayed. If a key has several options, each press will highlight the next option. If a key displays a single value or a slider above, use the rotary control to adjust. SET UP DEFAULT SYMB GROUP EDIT DEFAULT Within the text of this document they are written in capitals e.g. SORT LIST. This process of pressing buttons and soft keys to navigate to the required function, is simplified within this guide and represented by a strip e.g. WPTS/ MOB REVIEW AND EDIT WAYPOINTS ... SET DEFAULT SYM & GROUP... SET UP DEFAULT SYMB GROUP D7366-1 The Cursor The Cursor appears on the screen as a white cross. To make it easier to locate on screen, the cursor changes to a circle with a cross in it, when it is moved after a 10 second period of inactivity. The cursor is context-sensitive. When it is placed over an object e.g. a waypoint or chart feature, it changes color and a label or information associated with the object is displayed. When you place WPT the cursor over certain items, the soft keys change to enable you to access related operations. To practice using your Display without data from a GPS, scanner or fishfinder, switch on the simulator via the System Setup menu. D6762_4 Simulator: General Operation Setting up the display Card 3 How do I select how the applications are displayed? The applications are shown using a combination of page sets, pages and windows. There are five page sets each containing five pages with a combination of windows and applications in each. These sets can be edited to define the combination that suits your particular needs. Any changes you make will be saved to the system. You can change these preferences as many times as you wish. Page (1, 2, 3 or 4 windows) Window How do I select the Page Set? To confirm... OK Or PAGE Press and hold Highlight required page set. To customise... EDIT PAGE SET Follow on-screen instructions Note: Alternatively you can display the Select Page Set screen via the Menu key. How do I select a Page? PAGE SOFT KEY Press appropriate soft key Soft keys reflect current page set. Displayed option highlighted Note: Alternatively, repeatedly press PAGE until the required page is highlighted. ACTIVE The active window is bordered in red Press to move highlight to next window To temporarily maximise active window: ACTIVE Press and hold Press ACTIVE again to return to multiple windows mode. ? More information - See the 'General Operation' chapter of the Reference Manual D8990_2 How do I select a Window? General Operation Using CompactFlash cards Card 4 CAUTION CompactFlash Card In order to protect your E-Series Display and CompactFlash cards from irreparable damage, please adhere to the following: Fit the card the correct way around. DO NOT force. Ensure card door is firmly closed at all times. DO NOT use a metallic instrument (e.g. screwdriver or pliers) to aid card removal. Follow the correct procedure for removing a card (see below). DO NOT remove card during either a read or write operation. How do I insert a CompactFlash card? 1. Check that you are using the correct type of card. Raymarine recommend Navionics Chart cards or SANDISK CompactFlash cards. Narrow Groove 2. Open the chart card door, located on the front left of the display. Lip 3. Insert the card as shown, with the lip of the card facing inwards. It should position easily. If it does not, DO NOT force it, check the direction in which the lip is facing. 4. Gently press the card home and then firmly click the chart card door shut. How do I remove a CompactFlash card? ... with the unit powered ... with the unit powered down 1. Press MENU. The Setup menu is displayed. 1. Open the chart card door. 2. Use trackpad (up/down) to highlight and then (right) to select CF CARD REMOVAL. The system will now complete its checks. 2. Grip the card and pull to remove it from its slot. 3. Firmly click the chart card door shut. 3. When instructed to do so, open the chart card door and remove the card. ? More information... See the 'General Operation' chapter of the Reference Manual. D6724_4 4. Firmly click the chart door shut and press OK twice. What can I see? FIND SHIP CURSOR Understanding the chart GOTO ROUTES TRACKS PRESENTATION Card 5 What can I use the chart for? Find where you are. Interpret your surroundings. Place waypoints at specific locations. Navigate to a specific point. Monitor where you are going. Record where you have been. Measure the distance between two points. Chart range Chart orientation 4nm North-Up Build and follow routes. Manage and edit routes and tracks. Distinguish between fixed & moving objects (radar overlay). View photographs of ports and marinas. View information normally contained in an almanac. Display an aerial photo overlay. Motion mode Chart view (Relative Motion) Local Status bar Chart boundary Gully Ridge Route Portside Cursor Port point Creek point Waypoint Active waypoint Current position Cartographic object Track How do I move around the chart? To change the scale: OUT RANGE IN To pan the chart: Press RANGE (OUT) to see a larger area of the chart. Press RANGE (IN) to see a smaller area in more detail. Moves cursor. When cursor reaches window edge, chart pans to a different area. Press and hold to pan larger areas. How do I find where I am on the chart? ? More information... See 'Using the Chart' chapter of the E-Series Reference Manual D8978_2 The boat symbol indicates your position. If you cannot find your boat symbol : The screen automatically pans to your boat's position and re-activiates the motion FIND mode (see below - 'How do I change how SHIP CURSOR my boat moves on the chart'). What can I see? FIND SHIP CURSOR Using the chart ... GOTO ROUTES TRACKS PRESENTATION Card 6 Viewing detail on the chart Display additional information on a cartographic feature: OK OK For more information Setup To show/hide individual cartographic features: MENU To show/hide pre-set cartographic features: PRESENTATION... Cartography Setup... OFF ON DECLUTTER ON OFF How do I change the chart orientation? The orientation of the chart refers to the relationship between the chart and the direction you are travelling in. It is used in conjunction with motion mode (see below) to control how your boat and chart relate to one another and how they are displayed on screen. The default mode is North Up (N-UP). This displays your chart with true north upwards. As your heading changes the boat symbol moves accordingly. If desired, you can change the orientation mode to: Head Up (H-Up) - displays chart with boat's current heading upwards. As heading changes, boat symbol remains fixed Course Up (C-Up) - chart picture stabilized, current course upwards. Boat symbol moves as heading changes. To change the orientation mode: PRESENTATION... CHART MODE AND ORIENTATION... ORIENTATION H-UP N-UP C-UP Toggle as required How do I change how my boat moves on the chart? How your boat moves on the screen is referred to as the motion mode. The default setting for the chart is Relative Motion. This means that your boat is fixed on the screen and the chart moves relative to your boat i.e. If desired, you can change the motion mode to: True (TM) - the chart is fixed and the boat moves in true perspective to fixed landmasses on the screen. Autorange (AR) - selects and maintains the largest possible scale of chart that will display both the boat and the target waypoint This option is not available when radar/chart synchronization is ON. PRESENTATION... CHART MODE AND ORIENTATION... ? More information... MOTION MODE TM RM AR NOTE: When you pan the chart or toggle FIND SHIP/CURSOR to CURSOR, the motion mode is suspended. See 'Using the Chart' chapter of the Reference Manual D6740_4 To change the orientation mode: What can I see? Displaying additional information Card 7 Viewing object information OK More detailed information for selected object displayed. Move cursor over object, to display basic information. You can now: Locate the nearest waypoint, port, port service, tidal and current stations, wreck or obstruction, to the selected position. View detailed data for the selected port, tidal or current station. View panoramic photographs (dependent on the type of chart card in use) Search for a named port. Finding nearby features and services: 1. OK FIND NEAREST... Move cursor to required position SELECT PORT FIND NEAREST... 2. SELECT PORT WAYPOINTS PORTS PORT SERVICES TIDE STATIONS CURRENT STATIONS WRECKS OBSTRUCTIONS FIND Select required category 16 nearest to cursor in selected category displayed. Displaying port services: OBJECT INFO RAINBOW MARINA Photos Pilot Book OK Select appropriate port symbol Position 29058'.147N 093052'.215W Utilities Banks Restaurants-Bars Supplies Hookups Fuel SEARCH BY NAME Or Note: Alternatively you can search for port by name Services for selected port displayed Displaying tidal and current details: TIDE DATA OBJECT INFO MILE POINT Position 30006'.700N 84012'.700W Or OK Ebb Flood Ebb Flood 05:41AM 01:08AM 06:17AM 11:30AM +187.0 +358.0 +0.0 +358.0 Current information displayed ? More information... 0.5kt 0.2kt 0.0kt 0.2kt Or CURRENT DATA Graph page displayed See the 'Using the Chart' chapter of the Reference Manual. D8849_2 What can I see? Displaying additional information (continued) Card 8 How do I display a panoramic photo? If you are using a suitable chart card, you can display a panoramic photo(s) of many ports and marinas. The availability of photos is indicated by the camera symbol on the chart. This symbol is placed where the photo was taken and the angle of the shot is indicated by the camera symbol. OK VIEW PHOTO Select required camera symbol How do I display pilot book information? This will enable you to view detailed information normally contained in an almanac.. 1. OBJECT INFO OK Select appropriate port symbol RAINBOW MARINA Photos Pilot Book Position 29058'.147N 093052'.215W Book5, Chp5 Highlight and select the pilot book option 2. OBJECT INFO Position 29 58'.147N 093052'.215W RAINBOW MARINA Photos Pilot Book Book 5, Chp 5 VIEW PILOT BOOK Highlight required book/chapter Selected book/chapter displayed How do I display aerial photo overlay? The aerial photo overlay feature will help you to interpret your environment and its features. If you are using a suitable chart card, this overlay will appear by default on 3D chart windows and can be applied to individual 2D chart windows when required. Applying aerial photo overlay to a 2D chart: PRESENTATION… AERIAL OVERLAY ON OFF CHART LAYERS... Enable soft key ? More information... See the 'Using the Chart' chapter of the Reference Manual. D8841_2 3D - Aerial photo overlay can be switched off via 2D - Adjust the opaqueness level using the rotary control. the 3D Chart Setup Menu. Specify land only or land/sea overlay via the cartographic menu. What can I see? FIND SHIP ADJUST ON EYE CENTRE GOTO Understanding the 3D chart ADJUST ROTATE PITCH PRESENTATION Card 9 What can I use the 3D chart for? If you are using a suitable chart card you will be able to: Synchronize the 2D and 3D chart. Display a 3D view of land, sea & features. Locate where you are. Interpret your surroundings. Monitor where you are going. Range Mode Go to an existing waypoint. Navigate a route. Rotation Status bar North arrow Cartographic objects Center-of-view Active waypoint (with arrival circle) Boat symbol Depth scale How do I move around the 3D chart? To change the scale: Press RANGE (OUT) to see a larger area of the chart. Press RANGE (IN) to see a smaller area in more detail. To adjust rotation/pitch OUT RANGE 1. Select rotate or pitch: ADJUST ROTATE PITCH Or Press IN Toggle control to required function Turn To pan the 3d chart: To pan a 3D chart to a different area Rotates the view or changes the vertical angle of view. 2. Adjust the rotation/pitch: Changing the view on the 3D chart To enhance objects and make it easier to see their shape and position: To show/hide pre-set cartographic features: PRESENTATION... DECLUTTER ON OFF ? More information... ADJUST EXAGGERATION ADJUST EXAGGERATION Adjust factor as required See 'Using the 3D Chart' chapter of the E-Series Reference Manual D8735_2 PRESENTATION… 3D VIEW OPTIONS... What can I see? GOTO FIND SHIP Using the 3D chart ... ADJUST ON EYE CENTRE ADJUST ROTATE PITCH PRESENTATION Card 10 How do I find where I am on the 3D chart? Your position: Or If you cannot see your boat symbol: The 3D chart automatically redraws with the boat in forward looking view at your current position. FIND SHIP How do I change the motion mode? Using aerial photographs Active motion mode Default mode when 3D chart opened and there is a valid fix. Shows aerial view from above your boat. Planning mode: To view an area of the chart you are not currently in. The boat may not remain on the screen. To change to planning mode and pan to the area of the 3D chart you want to view: Turn The aerial photograph overlay helps you to interpret features in your environment. This option is accessed via the 3D Chart Setup menu. Or Synchronize 3D chart with 2D chart Note: When multiple windows are displayed and the current window is set to SYSTEM, changes made to the chart are reflected in all windows. If set to LOCAL no other window is affected. 3D location Eye point ? More information... PRESENTATION... CHART MODE AND ORIENTATION... CHART SYNC RDR 3D OFF See 'Using the 3D Chart' chapter of the Reference Manual. D8736_2 With a 2D chart window active, synchronise 3D to 2D chart: Basic Navigation Working with Waypoints WAYPOINT AT CURSOR WAYPOINT AT VESSEL WAYPOINT AT LAT/LON GO TO WAYPOINT OPTIONS REVIEW AND EDIT WAYPOINTS Card 11 What is a waypoint? A waypoint is a position marked on a chart, radar or fishfinder screen to indicate a site (for fishing, diving etc), or as a position to go to. You can place a waypoint at the cursor or your boat's position or at a specified position. Waypoints are represented in chart or radar applications as an 'X' (default) and by a vertical line labeled WPT in Fishfinder. Active waypoints are displayed on 3D Chart and CDI windows. The details of each waypoint are stored in a waypoint list. Waypoints can be renamed, edited, grouped, or erased, as necessary. To make full use of waypoint features, ensure your display is receiving heading and position data. We recommend that you regularly back-up your waypoints by archiving them to a CompactFlash card. Waypoints can also be transferred to another NMEA compatible instrument. Waypoint Networked systems If you have networked two or more E-Series Displays, the waypoints are stored on the master display and transferred to other displays via the SeaTalk High Speed network. How do I place a waypoint? ... at the cursor? ... at the vessel? WAYPOINT AT CURSOR WPTS/ MOB WAYPOINT AT VESSEL WPTS/ MOB WPT Move cursor to position Alternatively, press WPTS/MOB twice. How do I navigate to a point? GOTO... CAUTION GOTO CURSOR Always check that your route to a waypoint is safe before travelling towards it. Move cursor to position How do I navigate to a waypoint? ...using the waypoint list? Waypoint list GO TO WAYPOINT OPTIONS... WPTS/ MOB Name: Waypoint 1 Waypoint 2 Waypoint 3 Group: My Waypoint Position: 50 53’.826N 001 10’.963W Rng/Brg: 284 Temperature: Depth: Date: Time: ...using the cursor? GO TO WAYPOINT 4.315nm ---.-O F ---.-ft 05/11/2003 14:59:11 Highlight required waypoint To stop navigation to a waypoint: GO TO WAYPOINT WPT Place cursor over waypoint. GOTO... STOP GOTO OR: WPT Move cursor to required position Can I edit a waypoint? ? More information... Erase a waypoint See the 'Working with Waypoints' chapter of the Reference Manual D6729_4 Once a waypoint has been placed it can be edited in as variety of ways. You can: Change the default group or symbol Change the waypoint details Move a waypoint Basic Navigation How do I get to a point? SHOW/HIDE ROUTES FOLLOW ROUTE OPTIONS REVIEW AND EDIT ROUTES BUILD NEW ROUTE Card 12 What is a route? A route is made up of a series of waypoints. These waypoints can either be placed specifically for that route and/or you can use existing waypoints. You can save a route for future use or follow it immediately (Quick Route). Routes are stored in a route list. If you have networked two or more E-Series displays, the routes are stored in the master display and are transferred to the other displays via the SeaTalk High Speed network. Routes can be named, edited, erased and archived. After routes have been created you can choose which ones are displayed on your chart. Target waypoint highlighted Course from start point to target waypoint NORTH POINT Remaining legs of route KNOLL COWES How do I build a route by placing waypoints on screen? OUT 1. BUILD NEW ROUTE ROUTE... RANGE IN Move cursor into appropriate area Move cursor to required position for first waypoint Select a suitable scale PLACE PLACE WAYPOINT WAYPOINT 2. PLACE WAYPOINT SAVE ROUTE Move cursor to position for next waypoint. UNDO WAYPOINT 3. OK If you place a waypoint at the incorrect position, press UNDO WAYPOINT. How do I follow a route? ... from the route list GOTO... Route List FOLLOW ROUTE OPTIONS... Color ------------- Name Quick Route Route 1 Route 2 Route 3 FOLLOW ROUTE Select route ... from the start of route ... from a selected waypoint within route FOLLOW FROM HERE FOLLOW THIS ROUTE ? More information... Position cursor over appropriate waypoint See the 'Using the Chart' chapter in the Reference Manual, for more information on routes. D6730_4 Position cursor over any leg of required route What is around me? VRM/EBL Understanding the radar TARGET TRACKING ENHANCE ECHOES... GAIN PRESENTATION Card 13 What does the radar show me?.... Range Range ring spacing Motion mode Orientation Data bar 3nm Head-Up Relative Motion Rings ½nm Icon confirming radar connection Range ring Ship's heading marker Boat's position Surface vessel Waypoint Landmass VRM/EBL... TARGET TRACKING... GAIN... ENHANCE ECHOES... PRESENTATION... Typically your boat's position is at the centre of the display, and its dead ahead bearing is indicated by a vertical heading line, known as the Ship's Heading Marker (SHM). Remember that the radar picture may vary from visual observations that you make; a nearby small object may appear the same size on the screen as a distant large object. However, with experience the approximate size of different objects can be determined by the relative size and brightness of the echoes. How do I measure distances, ranges and bearings with the radar? VRMs Align a VRM on a target to display its range from your boat: EBLs Align an EBL on a target to display its bearing relative to your boat's heading: e.g. e.g. ADJUST VRM 1.800nm Combined VRM/EBL Combine a VRM and EBL to measure range and bearing of specified target. Rings 1/2nm Range rings e.g. ADJUST VRM 1.800nm ADJUST EBL 30.00S Use the range rings to gauge the approximate distances between two points or from your boat. ADJUST EBL 30.00S ? More information... See the 'Using the Radar' chapter of the Reference Manual D6731-4 Note: Range/bearing also displayed when VRM/EBL selected with the cursor. What is around me? TARGET TRACKING VRM/EBL Avoiding a collision ENHANCE ECHOES GAIN PRESENTATION Card 14 How can the radar help me avoid a collision? You can set up your E-Series Display to sound an alarm when anything comes within a pre-set range of the boat. These guard zones allow you to take any necessary action to avoid a collision. Guard zones A sector or circular zone fixed with respect to the Ships Heading Marker (SHM). If the SHM moves, or the centre is offset, or the range scale changes, the zone moves accordingly. What does a guard zone display? SHM SHM IMPORTANT A guard zone: Will only operate when a whole zone is displayed on screen, or displayed by offsetting the centre. Is inactive for 10 seconds after it is placed or re-sized, to avoid inappropriate alarms. Circular Zone Sector Zone How do I set up a circular guard zone? 1. Select guard zone function: TARGET TRACKING... ZONE 1 ON OFF MONITOR IN ZONES... SET UP ZONE 1 Toggle to ON 2. Select guard zone option: ZONE SHAPE SECTOR CIRCLE Turn Turn SET INNER xx.xx nm OK Toggle to required shape Turn to set inner boundary Turn to set outer boundary Press How do I distinguish between fixed and moving objects? Radar Range 12nm Status N-UP (RM) Ov To switch radar overlay on/off: Sys You can overlay radar image data on your chart allowing better distinction between fixed objects and other marine traffic. With a 2D chart window active: PRESENTATION... CHART LAYERS RADAR OVERLAY ON OFF To switch chart/radar synchronization on/off For best results, also switch on chart/radar sychronization. With a 2D chart window active: To change scanner range in this mode: CHART MODE AND ORIENTATION... RADAR OPTIONS... ? More information... See the 'Using the Radar' chapter of the Reference Manual. CHART SYNC RDR 3D OFF OUT RANGE IN D8838_2 PRESENTATION... What is around me? MONITOR IN ZONES ACQUIRE TARGET MARPA & AIS OPTIONS AIS LIST MARPA LIST Using MARPA.... Card 15 What is MARPA? Mini Automatic Radar Plotting Aid (MARPA) functions are used for target tracking and risk analysis. MARPA improves your standards of collision avoidance by obtaining detailed information for up to 10 targets, and provides continuous and rapid situation evaluation. MARPA tracks the selected targets and calculates target bearing, range, true speed, course, Closest Point of Approach (CPA), and Time to Closest Point of Approach (TCPA). Each tracked target can be displayed with a CPA graphic depicting the approximate target speed (vector length) and course (vector direction). Alternatively, move the cursor over the target to display the range and CPA. You can now access bearing and speed. Each target is continually assessed. An alarm sounds if a target becomes dangerous or lost. NOTE: For MARPA to operate, fast heading data is required. How do I set up the MARPA functions? MARPA & AIS OPTIONS... TARGET TRACKING... OK Highlight and select Select value from list How do I acquire a MARPA target? TARGET TRACKING... ACQUIRE TARGET Repeat to acquire further targets (10 max) 1800T 2.3kt Move cursor over target to acquire The target is acquired this takes a few seconds Target being acquired MARPA target symbols Dangerous target Safe target How do I view details of MARPA targets? MARPA LIST TARGET TRACKING... MARPA LIST... ID Bearing 312oT Range True Course 1.739nm 342oT 00h00m00s 9.4kt 22.7kt 1.305nm 1.774nm 00h00m00s 00h00m00s 1.305nm 1.774nm 276 T 321oT 086 T 247oT TCPA 00h00m00s 3.242nm 335 T 274 T CPA 1.739nm 68.4kt 3.242nm True Speed 9.9kt Tracked targets with data listed. How do I cancel MARPA target(s)? CANCEL TARGET Or: MARPA LIST... CANCEL ALL TARGETS ? More information... See the 'Using the radar' chapter of the Reference Manual. D6733_4 CANCEL TARGET What is around me? AIS VECTOR ON OFF AIS DATA AUTO ON OFF VIEW FULL AIS DATA Using AIS Card 16 AIS target symbols What is AIS? AIS uses digital radio signals to broadcast ‘realtime’ information between vessels and shore based stations via dedicated VHF frequencies. This information is used to identify and track vessels in the surrounding area and to provide collision avoidance data. AIS will augment your radar application, as it can operate in radar blind spots. In order to use the AIS feature, you will need a GPS and compass for timing and position information together with data from a suitable AIS receiver. How do I display AIS? On chart windows: PRESENTATION... AIS LAYER ON OFF CHART LAYERS... Toggle as required On radar windows: PRESENTATION... AIS LAYER ON OFF Toggle as required How is AIS data displayed? The AIS system displays other AIS equipped vessels in the surrounding area as targets overlaid on a chart or radar window. Up to 100 targets are displayed and are scaled according to the size of the vessel. A vector indicates the direction of travel of the vessel. As the vessel’s status changes, the symbol for the target will change accordingly. You can view detailed AIS data, safety critical target information, Alarm message (ALR) and Safety Related Message (SRM) messages. You can also set up a safe zone. How do I view target information? AIS DATA AUTO ON OFF 125oT 7.7kt 01.30nm 12h15m30s Sleeping target Target not activated, dangerous or lost. Activated target Target activated i.e. AIS vector displayed. Vector line (optional) shows predicted distance travelled within given time. Selected target Target selected with cursor. Can activate the target and view detailed data. COG/SOG vector Direction of turn Heading AIS Dangerous target Targets within specified distance (CPA) or time (TCPA). Dangerous target alarm sounds and target flashes. Uncertain target Calculated CPA/TCPA value uncertain. Lost target When signal of a dangerous AIS target not received for 10 seconds. Target orientated in COG or CSE direction as appropriate. Alarm sounds and target flashes WARNING: Smaller vessels do not have to be fitted with AIS and whilst it is mandatory for larger commercial vessels to carry AIS, its use is not. You should not assume that your AIS will display ALL vessels in your area. How do I view detailed AIS data? AIS Target info: Sim Target 6 COG 142oT MNSI 6 Name Sim Target 6 VIEW FULL AIS DATA Call sign SOG 25,7kt CPA Last seen 01/01/2006 01:13:21A M Lat 30 39’.702W Lon 080o18'.702W Hdg 159oT --,---nm Length --,---ft Beam --,---ft --,---nm TCPA --h--m--s IMO No Dest ETA Status --/--/---- --:--:--AM Under Way Using Engine Type Normal ? More information... See the 'AIS' chapter of the reference manual for data classes and how to customise this feature. D8809_2 Draught --ft Where am I? Monitoring a course.... Card 17 How do I monitor my course?.... Your course is shown on the chart application whilst motion mode is active. Using COG and heading vectors (Press DATA - CHART VECTORS - COG/HDG VECTORS). Use the Course Deviation Indicator (CDI). With your display receiving accurate heading and position information, you can monitor your course and accurately steer to a target waypoint. What does the CDI show me?.... The CDI gives a graphical representation of your boat's course. This 'rolling road' format represents a width of sea equal to the Cross Track Error (XTE) limits that you have specified in the Setup menu. As you travel towards the target waypoint, the checkered pattern moves down the screen to simulate movement at a rate proportional to your boat's speed. Direction of next waypoint Target waypoint Correction arrow Direction to steer Target way- On course point name line What do the steering instructions tell me? 0ff course On course XTE 0.000nm ? More information... Boat off center line. Correction arrow(s) indicate direction to steer to maintain course to target waypoint. The greater the XTE, the more arrows. See the 'Using the CDI' chapter of the Reference Manual D6734_4 Boat on center line. Zero XTE XTE 0.027nm What's under the boat? Adjust P1 SINGLE PRESET 2 DUAL PRESET 3 SHALLOW PRESET 4 DEEP PRESENTATION Understanding the fishfinder Card 18 What's under the boat? The fishfinder application, when connected to a suitable Digital Sounder Module (DSM) and transducer, will help you to see fish, bottom structure and underwater obstructions. The image scrolls from right to left at an automatically selected range and frequency to provide a record of the echoes seen. You can mark with a waypoint any positions of interest that you may wish to return to. These waypoints are added to the waypoint list and can be used by other applications. What can I see on the screen? Frequency modes Transducer Mode SINGLE Frequency Freq1: 200KHz-Auto Freq2: None Bottom of transducer F1: 200 kHz Depth markers Bottom Target depth 50 68 Target 69 Bottom depth ADJUST P1 SINGLE... PRESET 2 DUAL PRESET 3 SHALLOW PRESET 4 DEEP PRESENTATION... How do I interpret the bottom? A thin line indicates a hard bottom (sand) A wide line indicates a soft bottom (mud or seaweed cover) Peaks and troughs, indicate an uneven or rocky bottom or a wreck Dark layers indicate strong signals; lighter layers weaker signals. What influences target display? ? More information... See the 'Using the Fishfinder' chapter of the Reference Manual. D6735_5 The shape and size of echoes indicating targets, is influenced by a combination of: Boat speed - flatter at slower speeds Transducer frequency - broader at lower frequencies Target depth - larger near the surface Target size - larger targets return larger echoes What's under the boat? Adjust P1 SINGLE PRESET 2 DUAL PRESET 3 SHALLOW PRESET 4 DEEP PRESENTATION Using the fishfinder.... Card 19 How do I change the range or shift the image? Your system automatically adjusts the display depth range, selecting the shallowest depth that keeps the bottom on the lower half of the window. You can however, set this manually if required and move the image within the selected page up or down. Using the range controls will affect all fishfinder windows. Turn OUT OUT RANGE D6585-1 IN RANGE AUTO MAN RANGE SHIFT xx FT RANGE D6585-1 IN IN - decrease depth. OUT - increase depth. Press RANGE (IN or OUT) Turn to alter value. How do I change Presets? The Fishfinder application window allows you to have up to 4 user configurable preset modes, this allows you to select and configure the transducer frequency and screen view's (see E-Series reference manual section 6.6 Display mode settings, and section 6.10 Editing presets). NONE ZOOM A- SCOPE BOTTOM LOCK ADJUST P1 SINGLE ADJUST FREQ1 FREQ2 SELECT VIEW ZOOM Select the preset to change Highlight required view with trackpad Use the softkeys to select the different modes (unless instructed otherwise) Turn ZOOM FULL SPLIT ZOOM FACTOR x2 x3 x4 xR ZOOM POSITION AUTO MAN Select required zoom mode Select required zoom range Select required zoom position OK Turn to alter value How do I change the gain mode? The system automatically adjusts the gain control to display the sharpest image. If required, you can select the gain level to suit your fishing mode: Low - when cruising Med - when trolling High - when fishing CRUISING (LOW) TROLLING (MED) FISHING (HIGH) PRESENTATION... GAIN ... GAIN MODE AUTO MAN Highlight required preset OK COLOR GAIN AUTO MAN Select gain level ? More information... See the 'Using the Fishfinder' chapter of the Reference Manual. D6736_4 To define the gain mode still further, and to define other settings available on this page, select manual gain mode and then adjust the level using the rotary control. Monitoring data and engines Viewing video images Card 20 How do I monitor data?.... NAVIGATION WAYPOINT ROUTE FISHING SAILING The data application enables you to view numeric data generated by the system or by instruments available on NMEA 0183, SeaTalk, SeaTalk2, NMEA 2000 and SeaTalkhs. This information is displayed in a series of panels which contain data relating to a particular function or activity. These can be reconfigured to your needs. Press the appropriate soft key to select the panel of your choice. How do I monitor the engine(s)?.... ENGINE ENGINE & FUEL FUEL RESOURCES ENGINE & RESOURCES TWIN ENGINE The engine monitor application enables you to view data from up to three compatible engines. The information is displayed in a series of panels which contain data relating to engine, fuel and fuel resources. These can be reconfigured to your needs. Press the appropriate soft key to select the panel of your choice. To view data from 3 engines, change the 'No. of engine' setting in the Panel Setup Menu How do I view video images?.... VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 PRESENTATION The video application enables you to view images from a satellite TV, video or DVD player or on-board camera. Press the appropriate soft key, to select the video input of your choice or set CYCLE VIDEO to ON (via the PRESENTATION key), to cycle through the video inputs. ? More information... See the appropriate chapter of the Reference Manual. D7521_4 Note: Video images can only be viewed on the display to which the video source is connected. They cannot be networked to other Displays. Navtex and Sirius Weather Data Card 21 Navtex If connected to a Navtex receiver, you can use your display to view navigation, meteorological and search and rescue alerts. You can choose which category of alerts will automatically be displayed when one is received by your display. After you have read the message you can either erase it or save it to the database (100 maximum). You can view the list of saved messages at any time. Messages are viewed and alerts setup via the Setup Menu option Navtex Messages. Viewing saved messages 1. Setup Chart Setup... Cartography Setup MENU AIS Layer Setup... Navtex Messages...... Highlight and select Navtex messages Highlight required item in list Navtex Message List Date Time Message ID Navtex Message List Message Date Time Message ID Message 2. Associated message displayed in message box Move control to message box Scroll through message (if applicable) The Sirius Weather application (USA only) To run the Sirius Weather application you will need to purchase an SR100 weather receiver and a subscription to Sirius weather. Once connected, the weather application superimposes historical, current and forecasted weather graphics and environmental conditions on the world map and provides textual forecasts and warnings. These help you to determine the actual conditions in your vicinity or at a particular location. As in the chart application, use the cursor to move around the map and view different locations, and the range button to zoom in and out. Range Surface observation Marine Time data zone stations Wave heights 12:00 22/11 2400 nm Signal strength Medium To re-center the map on your boat use the FIND SHIP soft key. ? More information... FIND SHIP DISPLAY GRAPHICS... ANIMATE WEATHER... WEATHER REPORTS... PRESENTATION... Weather soft keys See the appropriate chapter for the Reference Manual. D8932_3 Note: As with all weather services, the information presented is advisory only and you should be aware that errors may occur. Note: If you have an SR100 connected, you can also control your Sirius satellite audio via your E-Series display. Sirius Weather Data DISPLAY GRAPHICS FIND SHIP WEATHER REPORTS ANIMATE WEATHER PRESENTATION (continued) Card 22 By default, all weather graphics are set to OFF. To display the required weather graphic: Weather Graphics NOWRad Storm Cast Sea Surface Temp Canadian Radar DISPLAY GRAPHICS... id Flor 26 OFF ON Highlight, select and switch graphic on/off as required Weather symbols (USA only) 24 OFF OFF OFF OFF 22 Or 22 Cu ba Canadian radar (light green- dark red) Waves (blues-green-red) Storm cast Wind (see below for details) Rain (green-yellow-red) Snow (blues) Mixture (pinks) Marine zones ida Flor Lightning (light-med-dark yellow) NWS Buoy C-man WST Sea surface temperature Surface observation station (pink) (blue-green-yellow -orange-red) Cities (grey) Surface pressure High pressure (blue) High pressure (red) Warm front (red) Cold front (blue) Occluded front (purple) 1010 1012 Stationary front (red-blue) Trough (brown) Squall line (red) Storm Tracks symbols Shown in three different colours: Grey - historical Red - current Orange - forecast Note: Highlight the symbol for additional information Dry line (brown) Hurricane (Category 1-5) Tropical storm Isobars (grey) Tropical disturbance or tropical depression Wind speed symbols (knots) etc. 13-17 18-22 23-27 28-32 33-37 ? More information... 38-43 44-47 48-52 53-57 58-62 63-67 68-72 73-77 78-82 83-87 88-93 94-97 See the Weather (USA only) chapter of the Reference Manual. 98-102 D8810_2 3-7 8-12 Autopilot Operation Using the Autopilot controls Card 23 How do I access Auto and Standby from my E-Series? Enabling the Autopilot from set up: To enable autopilot control on the E-Series display: Press the MENU button to open the Setup Menu. Select System Setup > System Integration > Autopilot Control > Enabled. Press the OK button. Enabling and engaging the autopilot To allow the E-Series to control autopilot functions, you need to enable autopilot control on the display unit. With autopilot control enabled, the unit lets you engage the autopilot whenever it has a target waypoint. You can see information for the target waypoint on the Pilot Control pop-up. The default autopilot setting is disabled. What are the Autopilot symbols? Wind Vane mode Power Steer mode Pilot Alarm mode Auto mode No Pilot connected Track mode Standby mode How do I engage and disengage the Autopilot in normal operation? When the autopilot is enabled, the E-Series prompts you to engage the autopilot whenever you initiate a GOTO or FOLLOW ROUTE. Select GOTO or FOLLOW ROUTE to display the Engage Pilot screen. SHIP FIND CURSOR AUTO GOTO GOTO CURSOR Select ENGAGE PILOT to display the Pilot Control screen. NOTE: If you press OK, CANCEL or the page times out without engaging the autopilot, you go back to the navigation screen with the autopilot disengaged. AIS OPTIONS NAVIGATION OPTIONS FOLLOW ROUTE OPTIONS GOTO WAYPOINT OPTIONS ENGAGE PILOT TRACK PRESENTATION STANDBY How do I disengage the Autopilot in an emergency? You can choose to disengage the pilot quickly if required by pressing the Power key ? More information... See Autopilot control chapter of the Reference Manual. AUTOPILOT STANDBY D10686_1 Select 'AUTOPILOT STANDBY' to put the pilot in the autopilot into standby mode and take control of the helm manually What is around me? TARGET TRACKING VRM/EBL Understanding the digital radar Card 24 ENHANCE ECHOES... GAIN PRESENTATION What do the digital radar colors show me?.... Preset Dual gain Radar range range indicator mode Orientation Motion mode Range ring separation Radar status Icons Data bar Ships heading marker Ships position Land mass AIS target Range ring The colors displayed represent the strength of the echoes received from targets. For most targets the echo strength is closely related to their size. Colors also help to distinguish targets within Clutter. Normally, targets will be displayed as a stronger color than the surrounding clutter. For example, a Buoy with a radar reflector will show clearly in sea clutter. How do I change the radar gain settings?.... The Radar application window allows you to select 4 user configurable preset modes, Buoy, Harbour, Coastal & Offshore. They allow you to configure the Gain, Color Gain, Rain & Sea Clutter settings to aid you in customising the display to suit the conditions (see E-Series Reference manual, 'Tuning the radar display'). For each gain preset, Auto mode is recommended, but you can change settings manually for each preset to suit individual situations. 24 GAIN... COASTAL MODE GAIN AUTO MAN GAIN AUTO MAN Select the Gain softkey Select the mode to change Select softkey, select MAN Change value to suit your conditions Turn Turn to alter value OK ? More information... See the 'Using the Radar (Digital)' chapter of the Reference Manual D10703_1 Select the ok to save manual setting softkey Operating a networked E-Series Display Card 25 What does a networked system do? If you have connected two or more E-Series Displays (via either a crossover coupler or SeaTalk High Speed Switch), all system data (from NMEA 0183, SeaTalk, SeaTalk2, NMEA 2000, SeaTalkhs waypoints, routes etc) can be transferred across the network enabling you to input, view and maintain data across all your displays irrespective of the Display from which the data originated (excepting Video Input). How is the network controlled? The display that has been installed and nominated as the master, should always be switched on (preferably first). The master display maintains the waypoint, route and track lists as well as data from NMEA and SeaTalk. Each time the master display detects a change on any display e.g. waypoint, route or track added or edited, the data is copied to the database which in turn is copied to all other Displays that are switched on. If the system does not detect a master, either because it is not switched on or because a master has not been selected, an alarm will sound and you will be prompted to set a master display. How do I change the master display? MENU Setup Chart Setup.... Cartogrphy Setup.... AIS setup.... System Setup.... Alarm Setup.... GPS Status.... Highlight System Setup Select System Setup Menu Position Mode... Lat/Long TD Setup... Simulator ON Bearing Mode True MOD Data Type Position Variation Source Auto(05oW) Manual Variation 00oE Language English (US) Extended Character Set OFF System Integration setup Menu DCM Message Seatalk Data Master Bridge NMEA Heading NMEA Output Setup.... ON ON ON OFF OFF ON Highlight Data Master Ground Trip Reset... Settings Reset... Settings and Data Reset... Select Date/Time Setup... Unit Setup... System Integration... Waypoint Password Setup... Select ON Highlight System Integration Raymarine Ltd Quay Point Northarbour Road, Portsmouth, Hampshire England PO6 3TD +44 (0)23 9269 3611 www.raymarine.com Raymarine Inc. 21 Manchester Street, Merrimack, NH 03054-4801 USA 1-603 881 5200 www.raymarine.com D8487_2 Select Document No 86114_4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Mode : UseNone XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2008:02:01 08:46:12Z Creator Tool : FrameMaker 7.0 Modify Date : 2008:02:01 08:46:34Z Format : application/pdf Title : untitled Document ID : uuid:e6251b4e-b686-4de9-b3e8-f1050525da78 Instance ID : uuid:9e2a3a76-835b-449c-81dc-09b961ce9e00 Page Count : 26 Creator : FrameMaker 7.0EXIF Metadata provided by EXIF.tools