Flir BelgiumBA RAY101 Handheld Marine Transceiver User Manual users manual

Raymarine UK Ltd. Handheld Marine Transceiver users manual

users manual

Ray101HandheldVHF RadioOwner’sHandbookDocument number: 81229_1Date: November 200381229_1.book Page i Wednesday, November 12, 2003 2:39 PM
81229_1.book Page ii Wednesday, November 12, 2003 2:39 PM
iiiAbout this HandbookIntroductionThis handbook describes the Ray101 portable VHF marine radio. The Ray101 provides two-way communications on all US, Canadian and International marine channels and ten weather channels.Conventions Used Throughout this handbook, the dedicated (labelled) keys are shown in bold capitals (for example: SCAN/SAVE). The LCD indicators and functions are shown in normal capitals (for example: TX).➤Operating procedures, which may consist of a single key-press or a sequence of numbered steps, are indicated by an arrow icon shown in the margin.Technical AccuracyTo the best of our knowledge, the information in this handbook was correct as it went to press. However, our policy of continuous product improvement and updating may change specifications without prior notice. As a result, unavoidable differences between the product and handbook may occur from time to time. Raymarine cannot accept liability for any inaccuracies or omissions it may contain.For the latest product information visit our website:www.raymarine.comWarrantyTo register your new Raymarine product, please take a few minutes to fill out the warranty registration card found at the end of this handbook. It is very important that you complete the owner information and return the card to the factory in order to receive full warranty benefits.81229_1.book Page iii Wednesday, November 12, 2003 2:39 PM
iv Ray101 Handheld VHF RadioImportant InformationSafety WarningsWARNING: Navigation AidAlthough we have designed this product to be accurate and reliable, many factors can affect its performance. As a result, it should only be used as an aid to navigation and should never replace common sense and navigational judgement. Always maintain a permanent watch so you can respond to situations as they develop.WARNING: Battery and Battery Charger SafetyDo not short the terminals in the charger base that recharge the batteries.Do not put the charger in water.Do not charge the batteries with + and – terminals reversed.Do not use charger if power plug or cable is damaged.Do not recharge batteries if physically deformed or leaking.EMC ConformanceAll Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. Their design and manufacture conform to the appropriate Electromagnetic Compatibility (EMC) standards but correct installation and use is required to ensure that performance is not compromised.81229_1.book Page iv Wednesday, November 12, 2003 2:39 PM
vRaymarine Products and ServicesRaymarine products are supported by a network of Authorized Service Representatives. Raymarine’s Technical Services representatives or your local dealer will be available to answer any questions you may have. For information on Raymarine products and services, contact either of the following:United States Raymarine, Inc.22 Cotton Road, Unit DNashua, NH 03063-4219USATelephone:1-603-881-52001-800-539-5539Fax: 1-603-864-4756Europe Raymarine LtdAnchorage ParkPortsmouth, HampshireEngland PO3 5TDTelephone: +44 (0) 23 9269 3611Fax: +44 (0) 23 9269 4642Or, you may contact us on the World Wide Web at:www.raymarine.comRaymarine is a registered trademark of Raymarine Limited.© Raymarine Limited 2003 81229_1.book Page v Wednesday, November 12, 2003 2:39 PM
vi Ray101 Handheld VHF Radio81229_1.book Page vi Wednesday, November 12, 2003 2:39 PM
viiContentsSafety Warnings .......................................................................................ivEMC Conformance .................................................................................ivChapter 1: General Information .........................................................................11.1 Introduction ...................................................................................... 11.2 Features ............................................................................................ 11.3 Licensing Requirements ................................................................... 2Chapter 2: Installation .........................................................................................52.1 Unpacking and Inspection ................................................................ 5Equipment Supplied .....................................................................52.2 Attaching the Antenna ...................................................................... 52.3 Attaching the Belt Clip ..................................................................... 62.4 Attaching the Wrist Strap ................................................................. 62.5 Battery Usage ................................................................................... 6Battery Tray .................................................................................. 6Charging Rechargeable NiMH Cells ........................................... 8Chapter 3: Getting Started ..................................................................................93.1 Keypad and Rotary Knobs ............................................................... 9Rotary Keys ..........................................................................10Push Keys .............................................................................10Description ................................................................................. 101. PWR/VOL ........................................................................102. SQ .....................................................................................103. PTT .................................................................................... 104. UP/DOWN ........................................................................ 115. Backlight / Keylock .......................................................... 116. 16/9 ................................................................................... 117. DW/TRI ............................................................................ 118. WX / BAND ...................................................................... 119. SCAN / SAVE ................................................................... 1110. HL/USER ........................................................................ 113.2 LCD Display .................................................................................. 121. (TX) Transmitting ...................................................................122. (RX) Receiving ....................................................................... 123. (USER) Favorite Channel Mode .............................................124. (SAVED) Memory Mode ........................................................135. (PSCAN) All Scan/Saved Scan/Priority Scan ........................ 136. (U I C) Channel Set .................................................................137. (B) Receive-only Channel ...................................................... 138. (A) Simplex Channel ..............................................................1381229_1.book Page vii Wednesday, November 12, 2003 2:39 PM
viii Ray101 Handheld VHF Radio9 Channel Number ......................................................................1310. Battery Level .........................................................................1311. Keylock ................................................................................1312. Indicators ..............................................................................1413. Signal Strength ......................................................................14Chapter 4: Operations ........................................................................................154.1 Turning the Power ON and OFF .....................................................154.2 Setting the Volume .........................................................................154.3 Setting the Squelch .........................................................................164.4 Setting the Power Output ................................................................16Overriding the Low Output Power Restriction ...........................174.5 Setting the Channel ........................................................................174.6 Selecting a Weather Channel ..........................................................17Weather Alert Operation .......................................................184.7 Setting the Frequency Band ...........................................................194.8 Selecting the Priority Channel ........................................................194.9 Selecting the Secondary Priority Channel ......................................20Reprogramming the Secondary Priority Channel .......................204.10 Transmitting ...................................................................................214.11 Turning On the Backlight ...............................................................224.12 Turning On the Keylock .................................................................224.13 Using the Scan Modes ....................................................................23All Scan .......................................................................................23Saved (Memory) Scan ................................................................24Priority All Scan ......................................................................... 25Priority Saved Scan .....................................................................264.14 Adding Channels to Memory .........................................................274.15 Using the Monitor Modes ...............................................................28Dual Watch ..................................................................................28Tri Watch .....................................................................................294.16 USER Channel Mode .....................................................................304.17 Resetting Factory Defaults .............................................................31Appendix A:Specifications .................................................................................33Appendix B:Channel List .....................................................................................35U.S. VHF Marine Radio Channels and Frequencies.................. 35Canadian VHF Marine Radio Channels and Frequencies.......... 38International VHF Marine Radio Channels & Frequencies ....... 43Weather Channel (WX) Frequencies ..........................................46Appendix C:Glossary ...........................................................................................47Index ..................................................................................................4981229_1.book Page viii Wednesday, November 12, 2003 2:39 PM
Chapter 1: General Information 1Chapter 1: General Information1.1 Introduction The Ray101 is a microprocessor-controlled, portable transceiver that provides reliable simplex (single frequency) and semi-duplex (two frequency) communications. This handbook describes the physical and functional characteristics of the radio.The Ray101 provides two-way communications on all US, Canadian and International marine channels and ten weather channels. Refer to the Frequency Tables in Appendix B, which list all marine VHF channels available in your radio. You should familiarize yourself with these tables as you are responsible for using the proper channels.1.2FeaturesThe Ray101 is designed and manufactured to provide ease of operation with excellent reliability. The Ray101 features:•Waterproof to IPX-7 standard •Saved-channels Scan and Priority Scan•Dual/Tri Watch Monitor modes•Dedicated key for switching to Channel 16•10 Weather Channels•Programmable Secondary Priority channel key•NiMH batteries (AA size) included•NiMH Quick Charger included•12VDC Cigarette Lighter Adapter included81229_1.book Page 1 Wednesday, November 12, 2003 2:39 PM
2 Ray101 Handheld VHF Radio1.3 Licensing RequirementsRaymarine radios comply with the Federal Communications Commission (FCC) and Industry Canada requirements that regulate marine VHF radio usage for the US and Canada, respectively. Marine VHF radio users in the US must comply with all applicable FCC rules and regulations, some of which are described here and in Section 5. This information was current at the time this handbook was printed. Up-to-date information, including licensing requirements, can be obtained on the FCC website at:www.fcc.gov/wtb/marineOfficial FCC forms can be obtained on the FCC website at:www.fcc.gov/formpage.htmlFCC NoticeThis device complies with Parts 15 and 80 of the FCC Rules. Operation is subject to the conditions that this device does not cause harmful interference. Changes or modifications to this equipment not expressly approved in writing by Raymarine, Incorporated could violate compliance with FCC rules and void the operator’s authority to operate the equipment.Station LicenseAn FCC Ship Radio Station License and Call Sign are not required for most recreational vessels travelling in US waters. Examples of radio equipment that do not require a license include: marine VHF radios, any type of Emergency Position Indicating Radio Beacon (EPIRB), any type of radar, GPS or LORAN receivers, depth finders, CB radio, or amateur radio (an amateur license is required). However, you must obtain a license if: (1) you are required by law or treaty to carry a radio on your vessel; (2) your vessel travels to foreign ports; (3) you use marine radio equipment on board your vessel other than the devices listed above. Ships that use MF/HF single side-band radio, satellite communications, or telegraphy must be licensed by the FCC. If necessary, you can obtain a Station License by filing FCC Form 605, which is available from the FCC website listed above.81229_1.book Page 2 Wednesday, November 12, 2003 2:39 PM
Chapter 1: General Information 3Operator LicenseAn Operator License is not required to operate a VHF Marine Radio within US territorial waters. However, a license is required to operate the radio if you dock in a foreign port (including Canada and Mexico) or leave a foreign port to dock in a U.S. port. You can request a Restricted Radiotelephone Operator Permit from the FCC by filing Form 753.INDUSTRY CANADAYou do not need a license to operate this radio within sovereign waters of Canada or the US. You will need a license to operate this radio outside of Canada or the US. To obtain Industry Canada licensing information, contact the nearest field or regional office, or write:Industry CanadaRadio Regulatory BranchAttention: DOSP300 Slater StreetOttawa, OntarioCanada, KIA OC8The following information about the radio is required to complete the license application:Industry Canada Certification Number 4069823227AD-----------------FCC Type Number PJ5RAY230--------------------------FCC Type Accepted Parts 15 and 80------------------Output Power 1 watt (low) & 25 watts (high)-----------------Modulation 16FE (FM)----------------------------Frequency Range 156.025-157.425-----------------------81229_1.book Page 3 Wednesday, November 12, 2003 2:39 PM
4 Ray101 Handheld VHF Radio81229_1.book Page 4 Wednesday, November 12, 2003 2:39 PM
Chapter 2: Installation 5Chapter 2: Installation2.1 Unpacking and InspectionUse care when unpacking the unit from the shipping carton to prevent damage to the contents. It is also good practice to save the carton and the interior packing material in the event you must return the unit to the factory.Equipment SuppliedThe following is a list of materials supplied with the Ray101: 1 Only connect Cigarette Lighter Adapter to 12VDC system. Connecting to other voltage systemscan damage the charger.2.2 Attaching the AntennaRotate the antenna clockwise to securely fasten it to the threaded connector on the top of the radio.Note: Do not operate the radio or press PTT without an antenna attached.Table 2-1: Supplied ComponentsPart Number DescriptionE43026 RAY101 Handheld VHF Radio81229 Ray101 Handbook—Antenna—Battery Tray—NiMH Quick Charger—12VDC Cigarette Lighter Adapter 1—Batteries, (6) AA NiMH (1300mAh)—Wrist Strap—Belt Clip81229_1.book Page 5 Wednesday, November 12, 2003 2:39 PM
6 Ray101 Handheld VHF Radio2.3 Attaching the Belt Clip➤To attach the belt clip and adapter:1. Remove the belt clip and adapter hardware from the packing materials.2. With the adapter button facing away from the Ray101, slide the adapter into the notch on the rear of the radio until it snaps into place.3. Hold the belt clip perpendicular to the Ray101 and slide the belt clip notch onto the adapter button until it snaps into place.4. Rotate the belt clip so that the longer end extends above the top of the radio.5. Squeeze together the two top ends of the belt clip and attach to your belt or pant waist.➤To remove the radio from the belt clip:1. Rotate the radio perpendicular to the belt clip.2. Press the release button at the top of the belt clip.3. Pull the radio up and away from the belt clip.2.4 Attaching the Wrist Strap1. Feed the narrow end of the strap through the two mounting holes at the top of the radio behind the antenna.2. Continue feeding the narrow end of the strap through the loop and pull tight.2.5 Battery UsageThe Ray101 can be powered by the supplied six (6) Nickel Metal Hydride (NiMH) batteries or with six (6) regular AA alkaline cells (not supplied), using the supplied Battery Tray.Battery Tray➤To open the Battery Tray and insert the battery cells:1. Using a coin or flat blade screwdriver, turn the screw at the base of the unit counterclockwise1/4 turn to the UNLOCK position.2. While holding the Ray101 in one hand, use the other hand to push the bat-tery tray downward and then away to separate it from the back of the radio.81229_1.book Page 6 Wednesday, November 12, 2003 2:39 PM
Chapter 2: Installation 7 Figure 2-1: Removing and Attaching the Battery Tray3. Lift up the tab located on the center right side of the battery tray cover and remove it from the battery tray.4. Locate the Battery Type switch just below the battery compartment and turn to the appropriate position: ALKALINE or NiMH. Figure 2-2: Removing the Battery Tray CoverRemove AttachBattery Type Switch(under batery cover)81229_1.book Page 7 Wednesday, November 12, 2003 2:39 PM
8 Ray101 Handheld VHF Radio5. Noting the proper orientation, install the AA cells in three rows of two batteries each.6. Replace the battery tray cover.WARNING: Be sure to set the Battery Type switch to the ALKALINE position before operating the radio with alkaline batteries. Operating the radio with alkaline batteries when the Battery Type switch is set to NiMH can cause battery leakage or explosion resulting in damage or injury.7. Slide the battery tray up into the rear of the radio and then downward until it snaps into place.8. Turn the screw at the base of the battery case clockwise to the LOCK position.Charging Rechargeable NiMH Cells The NiMH batteries must be fully charged before use. To charge the batteries:1.Insert the radio with the battery tray attached into the NiMH charger unit.2.Connect the AC wall adapter into a standard wall outlet.orConnect the Cigarette Lighter Adapter into a standard 12VDC Cigarette Lighter.3.Insert the molded plug into the connector on the side of the battery charger.The CHARGE indicator LED on the front of the charger lights when it is receiving voltage from the AC adapter.RED means the batteries are charging.GREEN means the batteries are fully charged.Initial charging will complete in approximately 8 hours. Typical time for recharging is 3 to 5 hours.CAUTION: 1.Make sure the switch just below the battery compartment is set to the NiMH position.2.Please follow the Battery Safety rules out-lined at the front of this handbook.LED81229_1.book Page 8 Wednesday, November 12, 2003 2:39 PM
Chapter 3: Getting Started 9Chapter 3: Getting Started3.1 Keypad and Rotary KnobsSeveral of the keys on the front panel of the base station serve multiple purposes. For the most part, the function indicated on the first line of the key is accessed by pressing and releasing that key. The function indicated on the second line of the key is accessed by pressing and holding the key for three seconds. Figure 3-1: Ray101 Keys Layout81229_1.book Page 9 Wednesday, November 12, 2003 2:39 PM
10 Ray101 Handheld VHF RadioRotary Keys Push Keys Description1. PWR/VOLUse this knob to turn the radio ON and OFF and to set the volume.2. SQUse this knob to set the squelch threshold, which cuts off the receiver when the signal is too weak for reception of anything but noise. 3. PTTWhile pressing this Press-to-Talk key radio transmission is enabled.Key Name Function1. PWR/VOL Power radio ON / OFF and adjust volume level 2. SQ Adjust squelch threshold levelKey Name Press & Release (<3 sec) Press & Hold(>3 sec)3. PTT Press-to-talk Press-to-talk4. UP/DOWN Channel increment/decrement Rapid channel change5. Backlight ON/OFF Keylock ON/OFF6. 16/9 Switches between the Priority and Working Channels Switches to secondary Priority CH (9);If already tuned to secondary channel, programs a new secondary Priority Channel.7. DW/TRI Dual Watch Mode Tri Watch Mode8. WX/BAND Weather Channel Mode Select frequency band9. SCAN/SAVE Scan ON/OFF SAVE/DELETE channel to/from memory10. HL/USER TX Power High/Low USER (Saved Memory Channel) Mode81229_1.book Page 10 Wednesday, November 12, 2003 2:39 PM
Chapter 3: Getting Started 114. UP/DOWNUse the arrow keys to change the current channel number.5. Backlight / KeylockUse this key to toggle ON or OFF the display’s backlight and the keylock function, which protects the radio from any keypad entry.6. 16/9 Use this key to switch to the priority channel or to change the value of the Secondary Priority Channel.7. DW/TRIUse this key to select either the Dual Watch or Tri Watch modes. Dual Watch monitors the current working channel and CH 16 in cycle. Tri Watch monitors CH 16, the current working channel and the channel you have set as the Secondary Priority Channel in cycle.8. WX / BANDUse this key to select the Weather mode or to alternate the frequency band between the USA, International and Canadian channel sets.9. SCAN / SAVEUse this key to enter a Scan Mode or to enter a channel into the radio’s memory.10. HL/USERUse this key to toggle the transmit power from HIGH to LOW and to enter User Channel Mode, which displays only the channels that you have saved to memory. 81229_1.book Page 11 Wednesday, November 12, 2003 2:39 PM
12 Ray101 Handheld VHF Radio3.2 LCD DisplayThe following describes the functional characters on the Ray101’s LCD. Figure 3-2: Ray101 LCD Layout1. (TX) TransmittingIndicates the PTT is being depressed and the radio is transmitting.2. (RX) ReceivingIndicates that the radio is receiving a radio signal.If the radio receives a signal but the squelch threshold is set so high that the signal cannot be heard, the RX indicator is not displayed but the bar graph on the left side of the LCD is illuminated to show the appropriate signal strength.3. (USER) Favorite Channel ModeIndicates the radio is in USER Mode. USER Mode displays only the channels that you have saved to memory, enabling you to easily scan your favorite channels while bypassing unwanted or seldom-used channels.81229_1.book Page 12 Wednesday, November 12, 2003 2:39 PM
Chapter 3: Getting Started 134. (SAVED) Memory ModeIndicates the current channel has been saved in memory. Appears during Saved Scan mode. Only saved channels are scanned during USER mode.5. (PSCAN) All Scan/Saved Scan/Priority ScanPSCAN appears during Priority Scan mode. SCAN appears during All Scan and Saved Scan. (SAVED also appears during Saved Scan mode.)6. (U I C) Channel SetIndicates which channel set is currently selected: US, International or Canadian.7. (B) Receive-only ChannelIndicates that you cannot transmit on the currently-selected channel; it is receive-only. Used with Canadian channels only.8. (A) Simplex ChannelIndicates that the currently-selected channel is simplex; you transmit and receive on the same frequency.9 Channel NumberDisplays the current channel number.10. Battery LevelIndicates current battery strength. Greater battery strength displays a larger number of segments in the bar graph. 11. KeylockIndicates the radio is protected from any keypad entry except for PTT and the backlight function.Fully chargedNormal operationNormal operationNeeds charging81229_1.book Page 13 Wednesday, November 12, 2003 2:39 PM
14 Ray101 Handheld VHF Radio12. IndicatorsIndicates special conditions:(WX) Weather ChannelWeather channel mode is active. US and Canada only.(ALERT) Weather AlertA weather alert is being received. US and Canada only.(HI/LO) TX PowerIndicates whether transmit power is set for 5 watts (HI) or 1 watt (LO).(DUAL) Dual WatchIndicates the radio is in Dual Watch mode.(TRI) Tri WatchIndicates the radio is in Tri Watch mode.13. Signal StrengthDisplays the relative strength of the TX and RX signals.When transmit output power is set for 1 watt, only two bars are displayed.When the output power is set for 5 watts, the full scale (5 bars) is displayed.When receiving, the bar graph indicates the strength of the signal being received. A stronger signal displays a larger number of segments in the bar graph.81229_1.book Page 14 Wednesday, November 12, 2003 2:39 PM
Chapter 4: Operations 15Chapter 4: Operations4.1 Turning the Power ON and OFFTurn the PWR/VOL knob clockwise until it clicks.When the unit powers up in Normal mode it:1. Beeps, illuminates the backlight at full brightness, and displays all seg-ments and indicators for 2 seconds.2. Displays the software version number on the LCD but without the deci-mal point. For example, version 1.1 would appear as 11.3. Recalls the last CH number, TX power settings and operation mode.If no last-used setting data exists, goes to CH 16 and high TX Power.➤To turn the unit OFF:Rotate the Volume knob completely counterclockwise until it clicks. 4.2 Setting the VolumeAdjust the PWR/VOL knob to control the loudspeaker volume level. Turn clockwise to increase the volume; counterclockwise to decrease the volume.Note: Key press beep volume is also controlled by the VOL level.81229_1.book Page 15 Wednesday, November 12, 2003 2:39 PM
16 Ray101 Handheld VHF Radio4.3 Setting the SquelchThe Squelch circuit sets the threshold for cutting off the receiver when the signal is too weak for reception of anything but noise.To properly set the squelch, rotate the SQ knob counterclockwise until audio is heard.Then rotate clockwise until background noise disappears.4.4 Setting the Power OutputThe choice of power output is dependent upon the distance of transmission and transmitting conditions. Press and release the HL/USER key to toggle the TX power from LOW (1 watt to HIGH (5 watts). The corresponding LO or HI indicator appears on the LCD. Note: Some channels are limited by regulation to be low power only. If the HILO operation request is denied, an error tone beeps.81229_1.book Page 16 Wednesday, November 12, 2003 2:39 PM
Chapter 4: Operations 17Overriding the Low Output Power RestrictionIn the US, channels 13 and 67 can temporarily override the low power restriction. ➤To override the LO power restriction on channels 13 or 67 and transmit at high power: Press and hold and hold the HL/USER key as you press and hold the PTT key. The TX power is set to HI power for as long as you hold down both keys.4.5 Setting the ChannelPress and release the UP arrow to increment the channel number.Press and release the DOWN arrow to decrement the channel.Press and hold either key for rapid channel scrolling.4.6 Selecting a Weather ChannelThe US National Oceanic and Atmospheric Administration (NOAA) broadcasts continuous weather reports and severe weather alerts, as needed. The Ray101 is programmed to receive10 NOAA weather channels and sound an alarm if a weather alert is received.Press and release the WX/BAND key to enter Weather mode. The WX indicator appears. Press Channel UP/DOWN to change the WX channel 0 through Channel 9.81229_1.book Page 17 Wednesday, November 12, 2003 2:39 PM
18 Ray101 Handheld VHF Radio Press and release the WX/BAND key again to return to normal operation.Note: 1. Weather broadcasts can only be heard in the US and Canada.2. During Weather mode, the PTT, SCAN/SAVE, DW/TRI and HL/USER keys are disabled and an error beep sounds if pressed.Weather Alert OperationWeather Alert is toggled ON and OFF by pressing and holding WX/BAND button in the weather mode. The ALERT icon illuminates. When Weather Alert function is enabled and the radio is tuned to the normal working channel, the last-used weather channel is checked every 30 seconds for weather alert tone. If the alert tone is detected, the WX and ALERT indicators flash and a short alarm tone sounds. The radio automatically turns to the currently-monitored WX channel where the weather alert has been detected. The alert is detected in all modes of operation (Standby, Dual and Tri Watch, Scan, etc.)81229_1.book Page 18 Wednesday, November 12, 2003 2:39 PM
Chapter 4: Operations 194.7 Setting the Frequency BandThe Ray101 can transmit and receive on all available US, Canadian and International marine VHF radiotelephone channels. Press and hold the WX/BAND key for greater than 3 seconds while in normal operation mode to alternate between the International, US and Canadian channel sets. The appropriate indicator is illuminated in the LCD: U for US, I for International, or C for Canadian channel sets. Note: Pressing and holding the WX/BAND key for greater than 3 seconds while in Weather mode toggles the Weather Alert mode.4.8 Selecting the Priority ChannelThe Ray101E provides you with a dedicated key for switching to the Priority Channel 16.If not already tuned to the Priority Channel 16, press and release the 16/9 key to switch to CH16 at high power.If already on CH 16, press and release the 16/9 to return to the last-used working channel.Note: When you press the 16/9 key, the radio al-ways switches to HIGH power. You can use the HL/USER key to change to LOW power.81229_1.book Page 19 Wednesday, November 12, 2003 2:39 PM
20 Ray101 Handheld VHF Radio4.9 Selecting the Secondary Priority ChannelThe Ray101E enables you to program the 16/9 key to store a Secondary Priority Channel. The default is CH 9.If on a working channel, press and hold the 16/9 for greater than 3 seconds to switch to the Secondary Priority Channel at high power. The default is CH 9.If on primary Priority CH16, press and hold the 16/9for greater 3 seconds to switch to the Secondary Priority Channel at HI power. The default is CH 9.If already on Secondary Priority Channel, press and release the 16/9 key to switch to Priority Channel 16 at high power.Reprogramming the Secondary Priority Channel1. Switch to the Secondary Priority Channel. 2. Press and hold the 16/9 key for greater 3 seconds to switch to Repro-gram mode. An alert tone sounds and the current Secondary Priority Channel flashes.3. Change the channel number with the UP and DOWN arrow keys. 4. Press and release the 16/9 key to save the new Secondary Priority selec-tion. An alert tone sounds to indicate that the Secondary Priority has been changed.During the reprogramming of the Secondary Priority Channel, the PTT, DUAL/TRI, and WX/BAND keys are disabled and sound error beep if pressed. 81229_1.book Page 20 Wednesday, November 12, 2003 2:39 PM
Chapter 4: Operations 214.10 TransmittingPress and hold the Press-to-talk (PTT) key to transmit on the selected channel, then release to receive. The TX indicator appears during transmission.The radio is equipped with a timeout timer in the event of a stuck key. After PTT has been held continuously for 5 minutes, transmission is discontinued and the radio automatically returns to receive mode. An Error beep is emitted 10 seconds before the time out is triggered and TX flashes on the display until PTT is released. The TX time out timer is reset once the PTT key is released.Note: If the current channel is a TX-prohibited channel, an alarm sounds when PTT is pressed, indicating such a transmission is not permitted.81229_1.book Page 21 Wednesday, November 12, 2003 2:39 PM
22 Ray101 Handheld VHF Radio4.11 Turning On the BacklightTo toggle the display’s Backlight ON or OFF, press and release the key. When the Backlight setting is enabled, any key press except PTT turns on the backlight for 5 seconds. If a key is pressed within the time frame, the time out is reset. The default setting is ON. 4.12 Turning On the Keylock To toggle the Keylock ON or OFF, press and hold the key for 3 seconds. When Keylock is enabled, the lock icon appears on the display. The Keylock setting protects the radio from any keypad entry except for PTT and the backlight function. Press and hold the key again for 3 seconds to release the keylock.81229_1.book Page 22 Wednesday, November 12, 2003 2:39 PM
Chapter 4: Operations 234.13 Using the Scan ModesThe RAY101 is equipped with three types of scan options: All Scan, Saved (Memory) Scan and Priority Scan. If there are no channels in memory, the default is All Scan.This function automatically searches for broadcasting channels. If a TX signal is received, the scan stops on the receiving channel as long as it is present. If the signal is lost for five seconds, the radio resumes scanning. During the Scan Modes:•Press the Channel UP/DOWN key to change the scan direction. UP increments the channel while DOWN decrements it.•Press and release SCAN/SAVE to terminate the SCAN mode and return to the last-used channel•DW/TRI and WX/BAND keys will not function and sounds an error beep if pressedAll ScanPress and release the SCAN/SAVE key when no channels are stored in memory to activate the All Scan function. The SCAN indicator appears on the LCD during All Scan.In All Scan mode, all channels in the channel set are scanned in sequence, assuming no channels have been stored in memory. After the last channel number has been scanned, the cycle repeats. All Scan is demonstrated in the figure to the left. 81229_1.book Page 23 Wednesday, November 12, 2003 2:39 PM
24 Ray101 Handheld VHF RadioNote: Whenever Weather Alert is activated, the WX Alert channel is also monitored during All Scan. If the WX Alert tone is detected, the scan is halted to broadcast the Weather Alert message.Saved (Memory) ScanPress and release the SCAN/SAVE key when there is at least one channel in memory to activate the Saved Scan function. In Saved Scan Mode, the SAVED and SCAN indicators appear on the LCD.In Saved Scan mode, only the channels that have been saved in memory are scanned in sequence. After the last saved channel number has been scanned, the cycle repeats. Saved Scan is demonstrated in the figure to the left.Note: Whenever Weather Alert is activated, the WX Alert channel is also monitored during Saved Scan. If the WX Alert tone is detected, the scan is halted to broadcast the Weather Alert message.81229_1.book Page 24 Wednesday, November 12, 2003 2:39 PM
Chapter 4: Operations 25 Priority All ScanPress and hold the SCAN/SAVE key while All Scan is active to initiate Priority Scan. .During Priority Scan, the PSCAN indicator appears on the LCD.Priority Scan searches for activity on all channels but alternates scanning the Priority Channel 16 after each channel.Priority Scan is demonstrated in the figure to the left.Note: Whenever Weather Alert is activated, the WX Alert channel is also monitored during Priority All Scan. If the WX Alert tone is detected, the scan is halted to broadcast the Weather Alert message.81229_1.book Page 25 Wednesday, November 12, 2003 2:39 PM
26 Ray101 Handheld VHF RadioPriority Saved ScanPress and hold the SCAN/SAVE key while Saved Scan is active to initiate Priority Saved Scan. The PSCAN and SAVED indicators appear on the LCD.Priority Saved Scan is much like Priority Scan except that the radio alternates searching for activity on the Priority Channel 16 and the channels stored in memory. Priority Saved Scan is demonstrated in the figure to the left.Note: Whenever Weather Alert is activated, the WX Alert channel is also monitored during Priority Saved Scan. If the WX Alert tone is detected, the scan is halted to broadcast the Weather Alert message.Press and hold SCAN/SAVE for 3 seconds to exit Priority/Priority Saved Scan and return to All/Memory Scan.81229_1.book Page 26 Wednesday, November 12, 2003 2:39 PM
Chapter 4: Operations 274.14 Adding Channels to MemoryThe Ray101 can store any channel. The stored channels are the ones scanned in the Saved (Memory) Scan mode.➤To Add Channels to Memory1. During normal operation mode, use the UP/DOWN key to select the desired channel for programming.2. Press and hold the SCAN/SAVE key for 3 seconds. The SAVED icon appears to indicate the current channel has been saved in memory. Any number of channels can be saved as memory channels. Separate memory channel groups exists for USA, International, and Canadian frequency sets.➤To Delete Channels from Memory1. During the normal mode, use the UP/DOWN key to select the channel to be deleted.2. Press and hold the SCAN/SAVE key for 3 seconds.The selected channel is deleted the channel from memory.To view the channels set in memory, switch to USER mode, as described in Section 4.16, USER Channel Mode.81229_1.book Page 27 Wednesday, November 12, 2003 2:39 PM
28 Ray101 Handheld VHF Radio4.15 Using the Monitor ModesThe Watch Modes monitor the programmed Priority Channel and other user-selected channel(s). The watch is halted when activity is detected on a monitored channel. The Ray101 is equipped with 2 types of monitor operations: Dual Watch and Tri Watch.Dual WatchPress and release the DW/TRI key to activate the Dual Watch mode. The DUAL indicator appears on the LCD.Dual Watch monitors the current working channel and Channel 16 in cycle.Dual Watch is demonstrated in the figure to the left; the sample working channel is CH 72. Whenever Weather Alert is activated, the WX Alert channel is also monitored during Dual Watch.Press and release the DW/TRI key to terminate Dual Watch and return to the previous working channel.Press and hold the DW/TRI key to terminate Dual Watch mode and go into Tri Watch mode.Press and release the 16/9 key to terminate Dual Watch mode and switch to the Priority Channel.Note: During Dual Watch mode, the SCAN/SAVE, USER, WX/BAND, and Channel UP/DOWN keys are inactive and sounds an error beep if pressed.81229_1.book Page 28 Wednesday, November 12, 2003 2:39 PM
Chapter 4: Operations 29Tri WatchPress and hold the DW/TRI key for 3 seconds to activate Tri Watch mode. The TRI indicator appears on the LCD.Tri Watch monitors in cycle Channel 16, the current working channel and the channel you have set as the Secondary Priority Channel.Tri Watch is demonstrated in the figure to the left; the sample working channel is CH 72. Note: Whenever Weather Alert is activated, the WX Alert channel is also monitored during Tri Watch. Press and release the DW/TRI key to terminate Tri Watch and return to the previous working channel. Press and release the 16/9 key to terminate Tri Watch mode and switch to the Priority Channel.Note: During Tri Watch Mode, the SCAN/SAVE, USER, WX/BAND, and Channel UP/DOWN keys are inactive and sounds an error beep if pressed.81229_1.book Page 29 Wednesday, November 12, 2003 2:39 PM
30 Ray101 Handheld VHF Radio4.16 USER Channel ModePress and hold the HL/USER key while in normal operation mode to enter User Mode. The USER and SAVED indicators appear. USER Channel Mode displays only the channels that you have saved to memory, which enables you to easily use your favorite channels while bypassing unwanted or seldom-used channels during a scan.Note: The procedure for saving a channel to memory is outlined in Section 4.14, Adding Channels to Memory.While in User Mode:•Press and release the SCAN/SAVE key to start Memory Scan mode.•Press and hold the SCAN/SAVE key to delete the current channel from memory list.•Press 16/9 to terminate User mode and switch to the Priority Channel.Note: You cannot switch Channel sets while in User Mode. The WX/BAND key does not function and sounds an error beep if pressed.Press and hold the HL/USER key for 3 seconds to quit User mode and return to the last-used working channel.81229_1.book Page 30 Wednesday, November 12, 2003 2:39 PM
Chapter 4: Operations 314.17 Resetting Factory DefaultsYou can reset many radio settings back to their factory defaults:•Erase any channels stored in memory•Turn OFF the backlight•Return to US channels, if another mode is selected•Turn OFF the Weather Alert setting, if active•Return power settings to their original state➤To perform the reset:1. Turn the radio OFF.2. Simultaneously press and hold the HL/USER and WX/BAND keys.3. While continuing to hold these keys, power the radio ON.The LCD remains blank for 2 seconds, and then the unit switches to channel 16. 81229_1.book Page 31 Wednesday, November 12, 2003 2:39 PM
32 Ray101 Handheld VHF Radio81229_1.book Page 32 Wednesday, November 12, 2003 2:39 PM
Appendix A: Specifications 33Appendix A: SpecificationsGeneralReceiver Size (H x W x D) 5.55”(141mm) x 2.4” (61mm) x 1.69” (43mm) without antennaWeight 12.6 oz (357g)Power Source 7.2V DC (6 x AA Alkaline or AA Ni-MH Batteries)Environmental:Operating Range:Storage Range: Humidity: Waterproof to IPX7-10°C to +55°C-20°C to +70°Cup to 95% at 35°C non-condensingFrequency Range:TransmitReceive 156.025 To 157.425 MHz156.050 To 163.275 MHzChannels All available US, Canadian and International VHF Marine Band.Oscillate Mode PLLModulation FM 16K0G3EChannel Spacing 25 kHz IncrementsFrequency Stability +/- 10PPM (+/- 0.001%)Antenna Socket SMADisplay 38.4mm x 48.3mm LCDBuilt in Speaker Ø36mm / Impedance 8 Ohm Sensitivity (12dB SINAD) 0.30uV Squelch Sensitivity (threshold) 0.20uVSpurious Response Rejection Ratio >60 dBAdjacent Channel Selectivity >60 dBIntermodulation Rejection Ratio >60 dBS/N at 3KHz Dev. >37 dBAudio Output Power At THD 10% 400mW max81229_1.book Page 33 Wednesday, November 12, 2003 2:39 PM
34 Ray101 Handheld VHF RadioTransmitter Audio Distortion <5%Audio Response +1/-3dB from true 6dB de-empha-sis from 300 to 2500 Hz, reference 1000Hz. Audio frequencies 3-20 KHz attenuated (at 1KHz by 60 log f / 3 dB; above 20KHz by 50 dB)Current Drain at: Max Audio PowerStandbyPower Saving230mA50mA20mA RF Power: Hi ModeLo Mode 5 W1 WModulation FM 16K0G3EMaximum Deviation ±5 KHzFrequency Stability +/- 10 ppm (-20°C to +50°C)S/N at 3KHz Dev. 34 dBModulation Distortion +/– 3KHz <5%Audio Response +1/-3dB from true 6dB pre-emphasis from 300 to 2500 Hz, reference 1000Hz. Audio frequen-cies 3-20 KHz attenuated (at 1KHz by 60 log f / 3 dB; above 20KHz by 50 dB) Spurious/Harmonic Emissions < 60 dBModulation Sensitivity 20mVCurrent Drain Hi PowerLo Power 1800mA700mA 81229_1.book Page 34 Wednesday, November 12, 2003 2:39 PM
Appendix B: Channel List 35Appendix B: Channel ListU.S. VHF Marine Radio Channels and Frequencies CH. No XMIT Freq RCV Freq Single Freq Use01A 156.050 156.050 x Port Operations and Commercial, VTS. Available only in New Orleans / Lower Mississippi area.105A 156.250 156.250 x Port Operations or VTS in the Houston, New Orleans and Seattle areas.06 156.300 156.300 x Intership Safety07A 156.350 156.350 x Commercial08 156.400 156.400 x Commercial (Intership only)09 156.450 156.450 x Boater Calling. Commercial and Non-Commercial.10 156.500 156.500 x Commercial11 156.550 156.550 x Commercial. VTS in selected areas.12 156.600 156.600 x Port Operations. VTS in selected areas.13 156.650 156.650 x Intership Navigation Safety (Bridge-to-bridge). Ships >20meters in length maintain a listening watch on this channel in US waters.214 156.700 156.700 x Port Operations. VTS in selected areas.15 - 156.750 x Environmental (Receive only). Used by Class ‘C’ EPIRBs.16 156.800 156.800 x International Distress, Safety and Calling. Ships required to carry radio, USCG, and most coast stations maintain a listening watch on this channel.317 156.850 156.850 x State Control18A 156.900 156.900 x Commercial19A 156.950 156.950 x Commercial20 157.000 161.600 Port Operations (duplex)20A 157.000 157.000 x Port Operations21A 157.050 157.050 x U.S. Coast Guard only81229_1.book Page 35 Wednesday, November 12, 2003 2:39 PM
36 Ray101 Handheld VHF Radio22A 157.100 157.100 x Coast Guard Liaison and Maritime Safety Information Broadcasts. Broadcasts announced on channel 16.23A 157.150 157.150 x U.S. Coast Guard only24 157.200 161.800 Public Correspondence (Marine Operator)25 157.250 161.850 Public Correspondence (Marine Operator)26 157.300 161.900 Public Correspondence (Marine Operator)27 157.350 161.950 Public Correspondence (Marine Operator)28 157.400 162.000 Public Correspondence (Marine Operator)63A 156.175 156.175 x Port Operations and Commercial, VTS. Available only in New Orleans / Lower Mississippi area.65A 156.275 156.275 x Port Operations66A 156.325 156.325 x Port Operations67 156.375 156.375 x Commercial. Used for Bridge-to-bridge communications in lower Mississippi River. Intership only.68 156.425 156.425 x Non-Commercial69 156.475 156.475 x Non-Commercial70 156.525 156.525 x Digital Selective Calling (voice communications not allowed)71 156.575 156.575 x Non-Commercial72 156.625 156.625 x Non-Commercial (Intership only)73 156.675 156.675 x Port Operations74 156.725 156.725 x Port Operations77 156.875 156.875 x Port Operations (Intership only)78A 156.925 156.925 x Non-Commercial79A 156.975 156.975 x Commercial. Non-Commercial in Great Lakes only.80A 157.025 157.025 x Commercial. Non-Commercial in Great Lakes only81A 157.075 157.075 x U.S. Government only – Environmental protection operations.82A 157.125 157.125 x U.S. Government onlyCH. No XMIT Freq RCV Freq Single Freq Use81229_1.book Page 36 Wednesday, November 12, 2003 2:39 PM
Appendix B: Channel List 37Boaters should normally use channels listed as Non-Commercial. Notes:1. The letter “A” following a channel number indicates simplex use of the ship station transmit side of an international duplex channel. Operations are different from that of international operations on that channel. 2. Channel 13 should be used to contact a ship when there is danger of collision. All ships of length 20 meters or greater are required to guard VHF channel 13, in addi-tion to VHF channel 16, when operating within U.S. territorial waters. 3. Channel 16 is used for calling other stations or for distress alerting. 83A 157.175 157.175 x U.S. Coast Guard only84 157.225 161.825 Public Correspondence (Marine Operator)85 157.275 161.875 Public Correspondence (Marine Operator)86 157.325 161.925 Public Correspondence (Marine Operator)87 157.375 161.975 Public Correspondence Marine Operator)88 157.425 162.025 Public Correspondence only near Canadian border88A 157.425 157.425 x Commercial, Intership onlyCH. No XMIT Freq RCV Freq Single Freq Use81229_1.book Page 37 Wednesday, November 12, 2003 2:39 PM
38 Ray101 Handheld VHF RadioCanadian VHF Marine Radio Channels and Frequencies CH No. XMIT Freq RCV Freq Area of Operation Use01 156.050 160.650 PC Public Correspondence02 156.100 160.700 PC Public Correspondence03 156.150 160.750 PC Public Correspondence04A 156.200 156.200 PC Intership, Ship/Shore and Safety:Canadian Coast Guard search and rescue104A 156.200 156.200 EC Intership, Ship/Shore and Commercial:Commercial fishing only05A 156.250 156.250 Ship Movement06 156.300 156.300 All areas Intership, Commercial, Non-commercial and Safety:May be used for search and rescue communications between ships and aircraft.07A 156.350 156.350 All areas Intership, Ship/Shore, Commercial08 156.400 156.400 WC, EC Intership, Commercial and Safety:Also assigned for operations in the Lake Winnipeg area.09 156.450 156.450 AC Intership, Ship/Shore, Commercial, Non-commercial and Ship Movement: May be used to communicate with aircraft and helicopters in predominantly maritime support operations.10 156.500 156.500 AC, GL Intership, Ship/Shore, Commercial, Non-commercial, Safety and Ship Movement: May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations.11 156.550 156.550 PC, AC, GL Intership, Ship/Shore, Commercial, Non-commercial and Ship Movement: Also used for pilotage purposes.12 156.600 156.600 WC, AC, GL Intership, Ship/Shore, Commercial, Non-commercial and Ship Movement: Port operations and pilot information and mes-sages.13 156.650 156.650 All areas Intership, Commercial, Non-commercial and Ship Movement:Exclusively for bridge-to-bridge navigational traffic.14 156.700 156.700 AC, GL Intership, Ship/Shore, Commercial, Non-commercial and Ship Movement: Port operations and pilot information and mes-sages.81229_1.book Page 38 Wednesday, November 12, 2003 2:39 PM
Appendix B: Channel List 3915 156.750 156.750 All areas Intership, Ship/Shore, Commercial, Non-commercial and Ship Movement: All operations limited to 1-watt maximum power. May also be used for on-board communications.16 156.800 156.800 All areas International Distress, Safety and Calling217 156.850 156.850 All areas Intership, Ship/Shore, Commercial, Non-commercial and Ship Movement: All operations limited to 1-watt maximum power. May also be used for on-board communications.18A 156.900 156.900 All areas Intership, Ship/Shore and Commercial:Towing on the Pacific Coast.19A 156.950 156.950 All areas except PC Intership and Ship/Shore: Canadian Coast Guard only.19A 156.950 156.950 PC Intership and Ship/Shore:Various Government departments.20 157.000 161.600 All areas Ship/Shore, Safety and Ship Movement:Port operations only with 1-watt maximum power.21A 157.050 157.050 All areas Intership and Ship/Shore:Canadian Coast Guard only.21B - 161.650 All areas Safety: Continuous Marine Broadcast (CMB) service.322A 157.100 157.100 All areas Intership, Ship/Shore, Commercial and Non-commercial:For communications between Canadian Coast Guard and non-Canadian Coast Guard stations only.23 157.150 161.750 PC Ship/Shore and Public Correspondence:Also in the inland waters of British Columbia and the Yukon.24 157.200 161.800 All areas Ship/Shore and Public Correspondence25 157.250 161.850 PC Ship/Shore and Public Correspondence: Also assigned for operations in the Lake Winnipeg area.25B - 161.850 AC Safety: Continuous Marine Broadcast (CMB) service.26 157.300 161.900 All areas Ship/Shore, Safety and Public Correspondence27 157.350 161.950 AC, GL, PC Ship/Shore and Public Correspondence28 157.400 162.000 PC Ship/Shore, Safety and Public Correspondence28B - 162.000 AC Safety: Continuous Marine Broadcast (CMB) service.CH No. XMIT Freq RCV Freq Area of Operation Use81229_1.book Page 39 Wednesday, November 12, 2003 2:39 PM
40 Ray101 Handheld VHF Radio60 156.025 160.625 PC Ship/Shore and Public Correspondence61A 156.075 156.075 PC Intership and Ship/Shore:Canadian Coast Guard only.61A 156.075 156.075 EC Intership, Ship/Shore and Commercial:Commercial fishing only.62A 156.125 156.125 PC Intership and Ship/Shore:Canadian Coast Guard only.62A 156.125 156.125 EC Intership, Ship/Shore and Commercial:Commercial fishing only.64 156.225 160.825 PC Ship/Shore and Public Correspondence64A 156.225 156.225 EC Intership, Ship/Shore and Commercial:Commercial fishing only.65A 156.275 156.275 Intership, Ship/Shore, Commercial, Non-commercial, Safety:Search & rescue and antipollution operations on the Great Lakes. Towing on the Pacific Coast. Port operations only in the St. Lawrence River areas with 1W maximum power. Pleasure craft in the inland waters of Alberta, Saskatchewan and Mani-toba (excluding Lake Winnipeg and the Red River).66A 156.325 156.325 Intership, Ship/Shore, Commercial, Non-commercial, Safety and Ship Movement: Port operations only in the St.Lawrence River/Great Lakes Areas with 1-watt maximum power.67 156.375 156.375 EC Intership, Ship/Shore and Commercial:Commercial fishing only.67 156.375 156.375 All areas except EC Intership, Ship/Shore, Commercial, Non-commercial, Safety: May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations.68 156.425 156.425 All areas Intership, Ship/Shore and Non-commercial:For marinas and yacht clubs.69 156.475 156.475 All areas except EC Intership, Ship/Shore, Commercial and Non-commercial69 156.475 156.475 EC Intership, Ship/Shore and Commercial:Commercial fishing only.70 156.525 156.525 All areas Digital Selective Calling for Distress, Safety and CallingCH No. XMIT Freq RCV Freq Area of Operation Use81229_1.book Page 40 Wednesday, November 12, 2003 2:39 PM
Appendix B: Channel List 4171 156.575 156.575 PC Intership, Ship/Shore, Commercial, Non-commercial, Safety and Ship Movement71 156.575 156.575 Intership, Ship/Shore and Non-commercial: For marinas and yacht clubs on the East Coast and on Lake Winnipeg. 72 156.625 156.625 EC, PC Intership, Commercial and Non-commercial:May be used to communicate with aircraft and helicopters in predominantly maritime support operations.73 156.675 156.675 EC Intership, Ship/Shore and Commercial:Commercial fishing only73 156.675 156.675 All areas except EC Intership, Ship/Shore, Commercial, Non-commercial, Safety: May also be used for communications with aircraft engaged in coordinated search and rescue and antipollution operations.74 156.725 156.725 EC, PC Intership, Ship/Shore, Commercial, Non-commercial and Ship Movement75 - - All areas Not available – Guard band for Channel 1676 - - All areas Not available – Guard band for Channel 1677 156.875 156.875 Intership, Ship/Shore, Safety and Ship Movement:Pilotage on Pacific Coast. Port operations only in the St. Lawrence River/Great Lakes areas with 1W maximum power.78A 156.925 156.925 EC, PC Intership, Ship/Shore and Commercial79A 156.975 156.975 EC, PC Intership, Ship/Shore and Commercial80A 157.025 157.025 EC, PC Intership, Ship/Shore and Commercial81A 157.075 157.075 Intership and Ship/Shore: Canadian Coast Guard use only in the St. Lawrence River/Great Lakes areas.81A 157.075 157.075 PC Intership, Ship/Shore and Safety:Canadian Coast Guard antipollution.82A 157.125 157.125 PC Intership, Ship/Shore and Safety:Canadian Coast Guard use only.82A 157.125 157.125 Intership and Ship/Shore: Canadian Coast Guard use only in the St. Lawrence River/Great Lakes areas.83 157.175 161.775 PC Ship/Shore and Safety:Canadian Coast Guard use only.CH No. XMIT Freq RCV Freq Area of Operation Use81229_1.book Page 41 Wednesday, November 12, 2003 2:39 PM
42 Ray101 Handheld VHF RadioArea of OperationAC: Atlantic Coast, Gulf and St. Lawrence River up to and including MontrealEC (East Coast): includes NL, AC, GL and Eastern Arctic areasGL: Great Lakes (including St. Lawrence above Montreal)NL: Newfoundland and LabradorPC: Pacific CoastWC (West Coast): Pacific Coast, Western Arctic and Athabasca-Mackenzie Watershed areasAll areas: includes East and West Coast areasNotes:1. The letter “A” following a channel number indicates simplex use of the ship sta-tion transmit side of an international duplex channel. Operations are different from that of international operations on that channel. 2. Channel 16 is used for calling other stations or for distress alerting.3. The letter “B” following a channel number indicates simplex use of the coast station transmit side of an international duplex channel. That is, the channel is Receive Only.83A 157.175 157.175 EC Intership and Ship/Shore:Canadian Coast Guard and other Government agencies.83B - 161.775 AC, GL Safety: Continuous Marine Broadcast (CMB) Service.84 157.225 161.825 PC Ship/Shore and Public Correspondence85 157.275 161.875 AC, GL, NL Ship/Shore and Public Correspondence86 157.325 161.925 PC Ship/Shore and Public Correspondence87 157.375 161.975 AC, GL, NL Ship/Shore and Public Correspondence88 157.425 162.025 AC, GL, NL Ship/Shore and Public CorrespondenceCH No. XMIT Freq RCV Freq Area of Operation Use81229_1.book Page 42 Wednesday, November 12, 2003 2:39 PM
Appendix B: Channel List 43International VHF Marine Radio Channels & Frequencies CH No. XMIT Freq RCV Freq Single Freq Use01 156.050 160.650 Public Correspondence, Port Operations and Ship Movement02 156.100 160.700 Public Correspondence, Port Operations and Ship Movement03 156.150 160.750 Public Correspondence, Port Operations and Ship Movement04 156.200 160.800 Public Correspondence, Port Operations and Ship Movement05 156.250 160.850 Public Correspondence, Port Operations and Ship Movement06 156.300 156.300 x Intership 107 156.350 160.950 Public Correspondence, Port Operations and Ship Movement08 156.400 156.400 x Intership09 156.450 156.450 x Intership, Port Operations and Ship Movement10 156.500 156.500 x Intership, Port Operations and Ship Movement 211 156.550 156.550 x Port Operations and Ship Movement12 156.600 156.600 x Port Operations and Ship Movement13 156.650 156.650 x Intership Safety, Port Operations and Ship Movement 314 156.700 156.700 x Port Operations and Ship Movement15 156.750 156.750 x Intership and On-board Communications at 1W only 416 156.800 156.800 x Distress, Safety and Calling17 156.850 156.850 x Intership and On-board Communications at 1W only 418 156.900 161.500 Public Correspondence19 156.950 161.550 Public Correspondence, Port Operations and Ship Movement20 157.000 161.600 Public Correspondence, Port Operations and Ship Movement21 157.050 161.650 Public Correspondence, Port Operations and Ship Movement22 157.100 161.700 Public Correspondence, Port Operations and Ship Movement23 157.150 161.750 Public Correspondence, Port Operations and Ship Movement24 157.200 161.800 Public Correspondence, Port Operations and Ship Movement81229_1.book Page 43 Wednesday, November 12, 2003 2:39 PM
44 Ray101 Handheld VHF Radio25 157.250 161.850 Public Correspondence, Port Operations and Ship Movement26 157.300 161.900 Public Correspondence, Port Operations and Ship Movement27 157.350 161.950 Public Correspondence, Port Operations and Ship Movement28 157.400 162.000 Public Correspondence, Port Operations and Ship Movement60 156.025 160.625 Public Correspondence, Port Operations and Ship Movement61 156.075 160.675 Public Correspondence, Port Operations and Ship Movement62 156.125 160.725 Public Correspondence, Port Operations and Ship Movement63 156.175 160.775 Public Correspondence, Port Operations and Ship Movement64 156.225 160.825 Public Correspondence, Port Operations and Ship Movement65 156.275 160.875 Public Correspondence, Port Operations and Ship Movement66 156.325 160.925 Public Correspondence, Port Operations and Ship Movement67 156.375 156.375 x Intership, Port Operations and Ship Movement68 156.425 156.425 x Port Operations and Ship Movement69 156.475 156.475 x Port Operations and Ship Movement70 156.525 156.525 x Digital Selective Calling for Distress, Safety and Calling 571 156.575 156.575 x Port Operations and Ship Movement72 156.625 156.625 x Intership73 156.675 156.675 x Intership 274 156.725 156.725 x Port operations and Ship movement75 156.775 156.775 x See Note 676 156.825 156.825 x See Note 677 156.875 156.875 x Intership78 156.925 161.525 Public correspondence, Port Operations and Ship Movement79 156.975 161.575 Public correspondence, Port Operations and Ship Movement80 157.025 161.625 Public correspondence, Port Operations and Ship Movement81 157.075 161.675 Public correspondence, Port Operations and Ship MovementCH No. XMIT Freq RCV Freq Single Freq Use81229_1.book Page 44 Wednesday, November 12, 2003 2:39 PM
Appendix B: Channel List 45Intership channels are for communications between ship stations.Intership communications should be restricted to Channels 6, 8, 72 and 77.If these are not available, the other channels marked for Intership may be used. Channels 10, 67 and 73 should be avoided within VHF range of coastal areas in Europe and Canada.Notes:1. Channel 06 may also be used for communications between ship stations and air-craft engaged in coordinated search and rescue operations. Ship stations should avoid harmful interference to such communications on channel 06 as well as to communications between aircraft stations, ice breakers and assisted ships during ice seasons. 2. Channels 10 or 73 (depending on location) are also used for the broadcast of Marine Safety Information by the Maritime and Coast Guard Agency in the UK only. 3. Channel 13 is designated for use on a worldwide basis as a navigation safety com-munication channel, primarily for intership navigation safety communications. 4. Channels 15 and 17 may also be used for on-board communications provided the effective radiated power does not exceed 1 Watt. 5. Channel 70 is to be used exclusively for digital selective calling for distress, safety and calling. 6. The use of Channels 75 and 76 should be restricted to navigation related communi-cation only and all precautions should be taken to avoid harmful interference to channel 16, e.g., by limiting power to 1 Watt or by means of geographical location. 82 157.125 161.725 x Public correspondence, Port Operations and Ship Movement83 157.175 161.775 x Public correspondence, Port Operations and Ship Movement84 157.225 161.825 x Public correspondence, Port Operations and Ship Movement85 157.275 161.875 x Public correspondence, Port Operations and Ship Movement86 157.325 161.925 x Public correspondence, Port Operations and Ship Movement87 157.375 157.375 Port Operations and Ship Movement88 157.425 157.425 Port Operations and Ship MovementCH No. XMIT Freq RCV Freq Single Freq Use81229_1.book Page 45 Wednesday, November 12, 2003 2:39 PM
46 Ray101 Handheld VHF RadioWeather Channel (WX) FrequenciesWeather Channel Frequency in MHzWX 0 163.275WX 1 162.550WX 2 162.400WX 3 162.475WX 4 162.425WX 5 162.450WX 6 162.500WX 7 162.525WX 8 161.650WX 9 161.77581229_1.book Page 46 Wednesday, November 12, 2003 2:39 PM
Appendix C: Glossary 47Appendix C: Glossary Term MeaningAll Scan A feature that scans all channels.Canadian Channels Channel designator as defined by Industry Canada.CH Channel selection keyDual Watch A feature that monitors the Priority Channel 16 while working on another channel.Duplex Transmit and receive on different frequenciesFCC Federal Communications Commission (US)International Channels Channel designator as defined by the ITUITU International Telecommunications UnionLCD Liquid Crystal DisplayNOAA National Oceanographic and Atmospheric Administration (USA)Priority Channel Channel 16 or 9 (or other secondary channel you have pro-grammed)Priority Scan (PSCAN) A feature that alternates monitoring the Priority Channel 16 with each of the regular channelsPTT switch Microphone push-to-talk switchRF Radio FrequencyRX ReceiveSaved Scan Scans only user-selected memory channelsSimplex Transmit and receive on the same frequencySquelch A circuit that sets the threshold for cutting off the receiver when the signal is too weak for reception of anything but noise.TX TransmitTri Watch A function that monitors the Priority Channel and Secondary Prior-ity Channel while working on another channel.US Channels Channel designations as defined by the FCC.VOL Volume keyVHF Very High Frequency (30MHz to 300MHz)81229_1.book Page 47 Wednesday, November 12, 2003 2:39 PM
48 Ray101 Handheld VHF RadioWeather (WX) Channels Channels for routine and emergency weather information broadcast by NOAA (USA).WX Weather Band keyWorking Channel The currently-selected (non-priority, non-WX) channel.Term Meaning81229_1.book Page 48 Wednesday, November 12, 2003 2:39 PM
49IndexSymbols"A" indicator 13"B" indicator 13"C" indicator 13"I" indicator 13"U" indicator 13Numerics16/9 key 11AAdding channels to memory 27ALERT indicator 14All Scan function 23Antenna 5BBacklight 11, 22BAND function 19Battery 6Charging 8Level indicator 13Tray 6Type switch 7Belt Clip 6CCanadian channels 38Canadian licensing 3CH indicator 13Channel ListCanadian frequencies 38International frequencies 43US frequencies 35WX frequencies 46Channel Sets 19Channel setting 17Channel UP/DOWN 11Charging batteries 8Conventions iiiDDelete channels from memory 27DUAL indicator 14Dual Watch 11, 28EEquipment suppied 5FFeatures 1Frequency Band 19Frequency settingsCanadian channels 38International channels 43US channels 35WX channels 46GGlossary 47HHI/LO indicator 14HI/LOW power selection 11, 16HL/USER key 11IInstallation 5International channels 43KKeylock 11, 22Keylock indicator 13Keypad 9LLCD display 12Licensing requirements 2MMemory 27Monitor modes 28, 29PPower 10Power ON/OFF 15Power selection 16Press-to-talk key 21Priority Channel 19Priority Scan function 25PSCAN indicator 13PTT 10, 2181229_1.book Page 49 Wednesday, November 12, 2003 2:39 PM
50 Ray101 Handheld VHF RadioRRecharging batteries 8RX indicator 12SSave channels to memory 27SAVED indicator 13Saved Scan function 24Scan function 23SCAN indicator 13SCAN/SAVE key 11Signal strength 14Squelch 10, 16TTransmitting 21TRI indicator 14Tri Watch 11, 29TX 21TX indicator 12UUS channels 35USER Channel Mode 11, 30USER indicator 12VVolume 15WWarning ivWarranty iiiWeather Channels 17Wrist Strap 6WX 17channels 46indicator 14WX/BAND key 1181229_1.book Page 50 Wednesday, November 12, 2003 2:39 PM
Warranty Certificate - VHF/Communications ProductsIn order to ensure that the equipment continues to operate efficiently and reliably, we recom-mend that before using the product, the customer carefully read the Owner’s Handbook and fol-low the advice on the safe and correct operation and use of the product. We recommend that Raymarine equipment be installed by an approved Raymarine installer.1. Limited Product WarrantyRaymarine warrants that all of its products, in the course of normal use, will be free from defects in material and workmanship for a period of 3 years (36 months) from date of sale to the original owner, subject to the limitations set forth in this warranty. Hailer horns, external speakers and accessories are warranted for 1 year (12 months) from dateof sale. The Raymarine warranty covers the parts and labor associated with any warranty repair as described above, provided that the product is returned to Raymarine or one of its approved National distributors, in accordance with part 3 hereof.2. Warranty RegistrationRegister your warranty on line at: http://www.raymarine.com.3. Obtaining Warranty ServiceIn the event of warranty service being required, contact Raymarine or its approved national dis-tributor – a full list of National distributors is available on Raymarine’s web site www.rayma-rine.com or directly from Raymarine.The affected product must be returned to Raymarine, or its approved national distributor with a copy of:(a) Proof of purchase showing the date of purchase and the name of the seller of the product; and the serial number of the affected product; or(b) A warranty card completed by the seller containing the information required in part (a) above. Subject to the limitations and other provisions set forth in this warranty, the product will be either repaired or replaced by Raymarine within a reasonable period of time and at no further cost to the customer. The determination of whether to repair or replace a product shall be at the sole discretion of Raymarine and shall be the sole remedy of the customer under this warranty.Warranty LimitationsRaymarine warranty does not apply to equipment that has been subjected to accident, abuse or misuse, shipping damage, alterations, corrosion, incorrect and/or non-authorized service, or product on which the serial number has been altered, mutilated or removed.Raymarine assumes no responsibility for damage incurred during installation or as a result of improper installation.This warranty does not cover routine system checkouts, alignment/calibration, sea-trials or com-missioning, unless required by replacement of part(s) in the area being aligned.Raymarine is not liable and assumes no responsibility for damage caused by or to other equip-ment, systems or components occasioned by improper or unauthorized connection, or use, of the product. 81229_1.book Page 1 Wednesday, November 12, 2003 2:39 PM
Document number: 84162-1September 2003Consumable items, including, but not limited to: fuses, batteries and lamps are specifically excluded from this warranty and Raymarine has no liability for such items.Travel costs, overtime/premium labor portion of services outside of normal working hours is not covered by this warranty.If repairs are necessary under the warranty, the affected product must be forwarded to a Ray-marine facility or an approved Raymarine service agent, at owner’s expense in a manner set forth in part 3 hereof.This warranty does not cover any differences in material, coloring, or size between those alluded to in corporate advertising, literature or published on the Internet, which is not specif-ically objected to at the time of delivery.To the extent consistent with State and Federal law:1. The foregoing warranty is Raymarine’s sole warranty and is applicable only to products sold as new. The remedies provided herein are in lieu of (i) any and all other remedies and warranties, whether express or implied including but not limited to, any implied warranty of merchantability or fitness for a particular purpose; and (ii) all obligations of Raymarine for damages including, but not limited to accidental, consequential or special damages (including punitive or multiple), or any financial loss, loss of profit, business, contracts, opportunity, goodwill or other similar loss arising out of or in connection with the purchase, use or performance of any Raymarine product, even if Raymarine has been advised of the possibility of such damages, and no case shall exceed the cost of the product. The remedies to the customer herein are exclusive. 2. Raymarine does not warranty products purchased via discount auctions or web-sites.*Some jurisdictions do not allow exclusion or limitation of incidental or consequen-tial damages so the above limitations or exclusions may not apply to you. This war-ranty gives you specific legal rights and you may also have other rights, which vary from jurisdiction to jurisdiction.Raymarine, Inc. is the sole authors of this policy and makes no other warranties, express or implied unless a separate, specific warranty has been written and pro-vided to the customer. This warranty supersedes and replaces all previous warran-ties.The Raymarine warranty terms and conditions herein do not effect the customer’s statutory rights and comply with EU Directive 1999/44/EC.* May not be applicable in EUAll Raymarine products are sold or provided hereunder are merely aids to navigation. It is the responsibility of the user to exercise discretion and proper navigational skill independent of any Raymarine equipment.81229_1.book Page 2 Wednesday, November 12, 2003 2:39 PM
Factory Service Centers United States of America UK, Europe, Middle East, Far EastRaymarine Inc22 Cotton Road, Unit DNashua, NH 03063-4219, USARaymarine LtdAnchorage Park, PortsmouthPO3 5TD, EnglandTelephone: +1 603 881 5200Fax: +1 603 864 4756www.raymarine.comTelephone: +44 (0)23 9269 3611Fax: +44 (0)23 9269 4642www.raymarine.comSales & Order ServicesTelephone: +1 800 539 5539 Ext. 2333 or+1 603 881 5200 Ext. 2333Customer SupportTelephone: +44 (0)23 9271 4713Fax: +44 (0)23 9266 1228Technical SupportTelephone: +1 800 539 5539 Ext. 2444 or+1 603 881 5200 Ext. 2444www.raymarine.comwww.raymarine.comProduct Repair CenterTelephone: +1 800 539 5539 Ext. 2118Model number Serial numberPurchased from Purchase dateDealer addressInstalled by Installation dateCommissioned byCommissioning dateOwner’s nameMailing addressPhone number E-mail addressThis portion should be completed and retained by the owner.81229_1.book Page 3 Wednesday, November 12, 2003 2:39 PM
81229_1.book Page 4 Wednesday, November 12, 2003 2:39 PM

Navigation menu