Flir BelgiumBA RAY70 Fixed Mount VHF Marine Radio User Manual
Raymarine UK Ltd. Fixed Mount VHF Marine Radio Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2538156 |
| Application ID | 56vi7R9noVjt359pFLKTLg== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 270.82kB (3385271 bits) |
| Date Submitted | 2015-02-18 00:00:00 |
| Date Available | 2015-02-18 00:00:00 |
| Creation Date | 2017-10-18 20:24:13 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-10-18 20:24:13 |
| Document Title | Users Manual |
| Document Creator | Arbortext 5.4 |
ENGLISH Document number: 88033-0.1 Date: 09-2014 Making a distress call In an emergency you can use your unit to make an automatic DSC distress call. With the spring loaded cover open: 4. Release the PTT button. Warning: Product installation and operation Making a Mayday call This product must be installed and operated in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel and/or poor product performance. In an emergency you can use your unit to make a Mayday call. 1. Press the 16 PLUS button. 2. Press and hold the PTT button. 3. Slowly and clearly speak the details of the distress: MAYDAY, MAYDAY, MAYDAY This isMAYDAY My position is 1. Press and hold the DISTRESS button for 3 seconds. Once the DISTRESS button is pressed a 3 second count down will begin, when the count down reaches zero the DSC distress call is transmitted. The distress call is repeated automatically until it is acknowledged. 2. Once an acknowledgement is received, or if no acknowledgement is received for 15 seconds; press and hold the PTT button. 3. Slowly and clearly speak the details of the distress in the following format: MAYDAY, MAYDAY, MAYDAY This is MAYDAY My position is I am I have I REQUIRE IMMEDIATE ASSISTANCE I am I have I REQUIRE IMMEDIATE ASSISTANCE OVER 4. Release the PTT button. 5. If an acknowledgement is not received then repeat steps 2 to 4 above. Important information Warning: Read the expanded handbook This document is an abbreviated ("quick start") handbook, containing only the basic information required to get you started with your new product. For the complete documentation and safety information for your product, please refer to the expanded handbook, available on the Raymarine website (www.raymarine.com). Warning: Potential ignition source This product is NOT approved for use in hazardous/lammable atmospheres. Do NOT install in a hazardous/lammable atmosphere (such as in an engine room or near fuel tanks). Warning: 12 Volt dc only This product must only be connected to a 12 volt dc power source. Warning: Positive ground systems Do not connect this unit to a system which has positive grounding. Warning: Switch off power supply Ensure the vessel’s power supply is switched OFF before starting to install this product. Do NOT connect or disconnect equipment with the power switched on, unless instructed in this document. OVER Warning: Chassis grounding Do NOT ground this product using the chassis ground terminal. Grounding this product to a vessel’s RF ground may cause galvanic corrosion. Warning: Antenna isolation To prevent galvanic corrosion your antenna must be isolated from any vessel metalwork using a suitable insulated e.g. plastic, mounting bracket. Warning: FCC Warning (Part 15.21) Changes or modiications to this equipment not expressly approved in writing by Raymarine Incorporated could violate compliance with FCC rules and void the user’s authority to operate the equipment. Warning: Maximum Permissible Exposure Caution: Ensure proper radio use Failure to observe these guidelines may expose those within the maximum permissible exposure (MPE) radius to RF radiation absorption that exceeds the FCC MPE limit. It is the radio operator’s responsibility to ensure that no one comes within this radius. Under no circumstances should a DSC distress alert be sent from your radio for test purposes. Such action is a violation of rules of use for radio equipment, and can result in heavy ines. For optimal radio performance and minimal human exposure to radio frequency electromagnetic energy, make sure the antenna is: • connected to the radio before transmitting • located where it will be away from people • located at least 1.5 meters (5 feet) from the radio’s main unit Caution: Power supply protection When installing this product ensure the power source is adequately protected by means of a suitably-rated fuse or automatic circuit breaker. Caution: Perform regular radio checks Perform regular radio checks when using your vessel, as recommended in radio training and certiication schemes and radio equipment rules of use. Caution: Cleaning When cleaning this product: • Do NOT wipe the display screen with a dry cloth, as this could scratch the screen coating. • Do NOT use abrasive, or acid or ammonia based products. • Do NOT use a jet wash. Water ingress Water ingress disclaimer Although the waterproof rating capacity of this product meets the stated IPX standard (refer to the product’s Technical Speciication), water intrusion and subsequent equipment failure may occur if the product is subjected to commercial high-pressure washing. Raymarine will not warrant products subjected to high-pressure washing. Disclaimer Raymarine does not warrant that this product is error-free or that it is compatible with products manufactured by any person or entity other than Raymarine. Raymarine is not responsible for damages or injuries caused by your use or inability to use the product, by the interaction of the product with products manufactured by others, or by errors in information utilized by the product supplied by third parties. Ray50 / Ray60 / Ray70 FCC Compliance Statement (Part 15.19) FCC Interference Statement (Part 15.105 (b)) Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Licensing This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio / TV technician for help. Industry Canada This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference; and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Prior to using this product please check your national requirements for both operators and equipment licensing. Station Licence FCC station license requirement An FCC Ship Radio Station License and Call Sign are not required for most recreational vessels travelling in US waters. However, you must obtain a license if your vessel travels to foreign ports. Ships that use MF/HF single side-band radio, satellite communications, or telegraphy must be licensed by the FCC. You can obtain a Station License by iling FCC Form 605, which is available from the FCC website listed above. Industry Canada Industry Canada license requirement You do not need a license to operate this product within sovereign waters of Canada or the US. You will need a license to operate this radio outside of Canada or the US. To obtain Industry Canada licensing information, contact the nearest ield or regional ofice, or write: Industry Canada Radio Regulatory Branch Attention: DOSP 300 Slater Street Ottawa, Ontario Canada, KIA OC8 European licensing requirements Regulations in some areas require that an Operator’s license is obtained before operating a VHF radio. It is your responsibility to determine whether a license is required in your area before operating this equipment. Additional information – Ray50 The following additional information is required for completing a license application in Canada and the US. Industry Canada certiication number 4069B-RAY50 D FCC ID PJ5–RAY50 FCC Type accepted Parts 2, 15 and 80 Output power 1 watt (low) and 25 watt (high) Modulation FM Frequency range 155.500 MHz to 163.275 MHz Additional information – Ray60 The following additional information is required for completing a license application in Canada and the US. Industry Canada certiication number 4069B-RAY60 D FCC ID PJ5–RAY60 FCC Type accepted Parts 2, 15 and 80 Output power 1 watt (low) and 25 watt (high) Modulation FM Frequency range 155.500 MHz to 163.275 MHz Additional information – Ray70 The following additional information is required for completing a license application in Canada and the US. Industry Canada certiication number 4069B-RAY70 D FCC ID PJ5–RAY70 FCC Type accepted Parts 2, 15 and 80 Output power 0.8 watt (low) and 23 watt (high) Modulation FM Frequency range 156.025 MHz to 157.425 MHz(TX) Maritime Mobile Service Identity (MMSI) This product is a class “D” Digital Selective Calling (DSC) device. A 9 digit MMSI number is required to operate DSC equipment. In some areas, a radio operator license is required before an MMSI number can be issued. Note: You can request an MMSI number from the same agency that issues radio or ship radio licenses in your area. Once obtained, you can program the MMSI number into your product by following the instruction supplied with the product. Once obtained, you can program the MMSI number into your product using the instructions provided in this handbook. If regulations in your area do not permit you to program the MMSI number yourself, your Raymarine dealer can program the number for you. Obtaining an MMSI number in the United States You can request an MMSI number from the FCC when you apply for a Station License. If your vessel does not require a license, you may obtain an MMSI by contacting BoatUS www.boatus.com. Obtaining an MMSI number in Canada You can obtain an MMSI number from your nearest Industry Canada Ofice. Obtaining an MMSI number in Europe and rest of world Am MMSI number should be requested from the same agency that issues radio operator licenses in your area. Automatic Transmitter Identiication System (ATIS) Your product includes ATIS functionality for use on the inland waterways of contracting governments of the “Regional Arrangement on the Radiocommunication Service for Inland Waterways” — also known as “RAINWAT”. ATIS adds data at the end of radio transmissions that identiies your station. ATIS operation can be turned on or off as needed via the radio’s menu. An ATIS ID can be obtained from the same agency that issues radio operator licenses in your area. Your ATIS ID should be programed into your product using the instructions provided in this handbook. Note: Contracting RAINWAT coutries include: Austria, Belgium, Bulgaria, Croatia, the Czech Republic, France, Germany, Hungary, Luxembourg, Moldova, Montenegro, the Netherlands, Poland, Romania, Serbia, the Slovak Republic and Switzerland. Note: In areas of extreme EMC interference, some slight interference may be noticed on the product. Where this occurs the product and the source of the interference should be separated by a greater distance. For optimum EMC performance we recommend that wherever possible: • Raymarine equipment and cables connected to it are: – At least 1 m (3 ft) from any equipment transmitting or cables carrying radio signals e.g. VHF radios, cables and antennas. In the case of SSB radios, the distance should be increased to 7 ft (2 m). – More than 2 m (7 ft) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element. • The product is supplied from a separate battery from that used for engine start. This is important to prevent erratic behavior and data loss which can occur if the engine start does not have a separate battery. • Raymarine speciied cables are used. Note: When ATIS is enabled, certain programing steps have been implemented to protect the integrity of the RAINWAT agreement, including the blocking of DSC functions when ATIS is enabled. EMC installation guidelines Raymarine equipment and accessories conform to the appropriate Electromagnetic Compatibility (EMC) regulations, to minimize electromagnetic interference between equipment and minimize the effect such interference could have on the performance of your system Correct installation is required to ensure that EMC performance is not compromised. • Cables are not cut or extended, unless doing so is detailed in the installation manual. Note: Where constraints on the installation prevent any of the above recommendations, always ensure the maximum possible separation between different items of electrical equipment, to provide the best conditions for EMC performance throughout the installation Antenna mounting and EME exposure Ensure that the antenna is connected to the radio before transmission. Raymarine declares a Maximum Permissible Exposure (MPE) radius of 1.5 metres (4.9 ft) (per OET Bulletin 65) for this system, assuming 23 watts output to an omnidirectional antenna of 3dBi gain or less. For watercraft with suitable structures, the antenna base must be at least 3.5 metres (11.5 ft) above the main deck to meet the MPE for persons up to 2 metres Ray50 / Ray60 / Ray70 (6.6 ft) tall. For watercraft without such structures, the antenna must be mounted so that its base is a minimum of 1.5 metres (4.9 ft) vertically from heads of all persons. You will need this serial number when registering your product online. You should retain the label for future reference. The antenna must be isolated from the vessel’s metalwork using an insulated (e.g. plastic) mounting bracket. IMO and SOLAS Connections to other equipment Requirement for ferrites on non-Raymarine cables If your Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite MUST always be attached to the cable near the Raymarine unit. Declaration of conformity Raymarine UK Ltd. declares that this product is compliant with the essential requirements of R&TTE directive 1999/5/EC. The original Declaration of Conformity certiicate may be viewed on the relevant product page at www.raymarine.com. Product disposal Dispose of this product in accordance with the WEEE Directive. The Waste Electrical and Electronic Equipment (WEEE) Directive requires the recycling of waste electrical and electronic equipment. Whilst the WEEE Directive does not apply to some Raymarine products, we support its policy and ask you to be aware of how to dispose of this product. Warranty registration To register your Raymarine product ownership, please visit www.raymarine.com and register online. It is important that you register your product to receive full warranty beneits. Your unit package includes a bar code label indicating the serial number of the unit. The equipment described within this document is intended for use on leisure marine boats and workboats NOT covered by International Maritime Organization (IMO) and Safety of Life at Sea (SOLAS) Carriage Regulations. Applicable products This document is applicable to the following products: Name Part number Features E70243 Ray50 • SeaTalkng® • NMEA 0183 • Passive speaker connection Technical accuracy To the best of our knowledge, the information in this document was correct at the time it was produced. However, Raymarine cannot accept liability for any inaccuracies or omissions it may contain. In addition, our policy of continuous product improvement may change speciications without notice. As a result, Raymarine cannot accept liability for any differences between the product and this document. Please check the Raymarine website (www.raymarine.com) to ensure you have the most up-to-date version(s) of the documentation for your product. E70245 Ray60 • SeaTalkng® • NMEA 0183 • Passive speaker connection • Up to 2 stations E70251 Ray70 • SeaTalkng® • NMEA 0183 • Passive speaker connection • Up to 2 stations • Built-in AIS receiver • Built-in GNSS (GPS and GLONASS) receiver • Loud hailer connection Location and mounting General location requirements When selecting a location for the unit it is important to consider a number of factors. Antenna mounting and EME exposure Ensure that the antenna is connected to the radio before transmission. Raymarine declares a Maximum Permissible Exposure (MPE) radius of 1.5 metres (4.9 ft) (per OET Bulletin 65) for this system, assuming 23 watts output to an omnidirectional antenna of 3dBi gain or less. For watercraft with suitable structures, the antenna base must be at least 3.5 metres (11.5 ft) above the main deck to meet the MPE for persons up to 2 metres (6.6 ft) tall. For watercraft without such structures, the antenna must be mounted so that its base is a minimum of 1.5 metres (4.9 ft) vertically from heads of all persons. The antenna must be isolated from the vessel’s metalwork using an insulated (e.g. plastic) mounting bracket. Compass safe distance To prevent potential interference with the vessel's magnetic compasses, ensure an adequate distance is maintained from the product. When choosing a suitable location for the product you should aim to maintain the maximum possible distance from any compasses. Typically this distance should be at least 1 m (3 ft) in all directions. However for some smaller vessels it may not be possible to locate the product this far away from a compass. In this situation, when choosing the installation location for your product, ensure that the compass is not affected by the product when it is in a powered state. GPS location requirements In addition to general guidelines concerning the location of marine electronics, there are a number of environmental factors to consider when installing equipment with an internal GPS antenna. Mounting location • Above Decks mounting: Provides optimal GPS performance. (For equipment with appropriate waterproof rating.) • Below Decks mounting: GPS performance may be less effective and may require an external GPS antenna mounted above decks. Prevailing conditions The weather and location of the vessel can affect the GPS performance. Typically calm clear conditions provide for a more accurate GPS ix. Vessels at extreme northerly or southerly latitudes may also receive a weaker GPS signal. GPS antenna mounted below decks will be more susceptible to performance issues related to the prevailing conditions. Ventilation requirements To provide adequate airlow: • Ensure that equipment is mounted in a compartment of suitable size. • Ensure that ventilation holes are not obstructed. • Ensure adequate separation of equipment. Mounting surface requirements Ensure units are adequately supported on a secure surface. Do NOT mount units or cut holes in places which may damage the structure of the vessel. Cable routing requirements Ensure the unit is mounted in a location which allows proper routing and connection of cables: This location provides optimal GPS performance (above decks). In this location, GPS performance may be less effective. This location is NOT recommended for GPS antenna. Vessel construction The construction of your vessel can have an impact on GPS performance. For example, the proximity of heavy structure such as a structural bulkhead, or the interior of larger vessels may result in a reduced GPS signal. Before locating equipment with an internal GPS antenna below decks, seek professional assistance and consider use of an external GPS antenna mounted above decks. • Minimum cable bend radius of 100 mm (3.94 in) is required unless otherwise stated. • Use cable supports to prevent stress on connectors. Electrical interference Select a location that is far enough away from devices that may cause interference, such as motors, generators and radio transmitters/receivers. Power supply Select a location that is as close as possible to the vessel’s DC power supply. This will help to keep cable runs to a minimum. Ray50 / Ray60 / Ray70 Product dimensions Ray60 and Ray70 dimensions Ray50 dimensions The Ray60 and Ray70 can be lush mounted or bracket mounted. The Ray50 can be lush mounted or bracket mounted. Ray50 Flush mount dimensions Fistmic dimensions Ray60 and Ray70 Flush mount dimensions The Fistmic’s itted, coiled lead can be extended comfortably to approximately 1 meter (3.3 ft.) Mounting options The product can be mounted in the following conigurations. Ray50 Bracket mount dimensions Ray60 and Ray70 Bracket mount dimensions 1. Table top mount 2. Overhead mount 3. Bulkhead mount 4. Flush mount Bracket mounting Follow the steps below to mount the product on it’s bracket. Before mounting the unit ensure that you have: • Selected a suitable location, ensuring there is nothing behind the mounting surface that may be damaged when drilling. • Identiied the cable connections and route that the cables will take. • Attached the front bezel. 3. Use the ixings provided to attach the bracket securely to the mounting surface. 4. Attach the unit to the bracket and secure in place using the bracket mounting knobs. Note: Drill bit, tap size and tightening torque is dependent on the thickness and type of material the unit is to be mounted on. Ray50 Removing the mounting hole covers Before the Ray50 can be lush mounted the mounting hole covers must be removed. 1. Using a drill and a 4 mm (5/32) drill bit, drill out the 4 mounting holes. Holes should be drilled from the front of the unit, taking care not to damage the unit by applying too much force to the drill. Flush mounting the Ray50 To lush mount the Ray50 follow the steps below. Before mounting the product, ensure that you have: • Selected a suitable location, ensuring there is nothing behind the mounting surface that may be damaged when drilling / cutting. 1. Using a lat blade screw driver, insert the tip of the screw driver in the slot between the back of the cover and the unit. 2. Gently lever the cover forward away from the unit. • Identiied the cable connections and route that the cables will take. • Drilled out the mounting holes on the unit. • Removed the mounting hole covers. 3. Repeat steps 2 and 3 for the remaining mounting hole covers. Drilling out the mounting holes – Ray50 Before lush mounting the product the mounting holes must be drilled out. 1. Mark the location of the bracket mounting holes on the mounting surface. 2. Drill holes for the mounting ixings using a drill with a suitable sized drill bit. 10 Guides for the mounting holes can be found in the corners of the unit, under the mounting hole covers. Ray50 / Ray60 / Ray70 11. Attach the mounting hole covers. 1. Using a drill and a 4 mm (5/32) drill bit, drill out the 4 mounting holes. 1. Check the selected location for the unit. A clear, lat area with suitable clearance behind the panel is required. 2. Fix the supplied mounting template to the selected location, using masking or self-adhesive tape. 3. Using a suitable hole saw (the size is indicated on the template), make a hole in each corner of the cut-out area. Holes should be drilled from the front of the unit, taking care not to damage the unit by applying too much force to the drill. Note: The supplied gasket provides a seal between the unit and a suitably lat and stiff mounting surface or binnacle. The gasket should always be used. It may also be necessary to use a marine-grade sealant if the mounting surface or binnacle is not entirely lat and stiff or has a rough surface inish. 4. Using a suitable saw, cut along the inside edge of the cut-out line. Ray60 - Ray70 5. Ensure that the unit its into the removed area and then ile around the rough edge until smooth. Drilling out the mounting holes – Ray60 / Ray70 6. Drill 4 holes as indicated on the template to accept the ixings. 7. Remove the backings from the supplied gasket. 8. Place the gasket in position on the back of the unit and press irmly onto the lange. Before lush mounting the product the mounting holes must be drilled out. Guides for the mounting holes can be found in the corners of the unit, under the front bezel. Flush mounting – Ray60 / Ray70 To lush mount the Ray60 / Ray70 follow the steps below. Before mounting the product, ensure that you have: • Selected a suitable location, ensuring there is nothing behind the mounting surface that may be damaged when drilling / cutting. • Identiied the cable connections and route that the cables will take. • Drilled out the mounting holes on the unit. • Removed the front bezel. 9. Connect the power, and other cables to the unit. 10. Slide the unit into place and secure using the ixings provided. 11 Note: The supplied gasket provides a seal between the unit and a suitably lat and stiff mounting surface or binnacle. The gasket should always be used. It may also be necessary to use a marine-grade sealant if the mounting surface or binnacle is not entirely lat and stiff or has a rough surface inish. Attaching the front bezel – Ray60 / Ray70 1. Check the selected location for the unit. A clear, lat area with suitable clearance behind the panel is required. Fistmic / Handset mounting The Fistmic and optional Handset can be mounted by following the steps below. Whilst only the Fistmic is pictured below the steps are identical when mounting the Handset using the mounting clip. Before mounting the unit, ensure that you have: After installation the front bezel can be attached following the steps below. • Selected a suitable location, ensuring there is nothing behind the mounting surface that may be damaged when drilling. The following procedure assumes that the unit has already been mounted in position. • Identiied the cable connections and route that the cables will take. 1. Orientate the bottom-right side of the bezel under the bottom-right side of the unit, ensuring that the clips along the bottom edge of the bezel latch into position. 2. Fix the supplied mounting template to the selected location, using masking or self-adhesive tape. 3. Using a suitable hole saw (the size is indicated on the template), make a hole in each corner of the cut-out area. 4. Using a suitable saw, cut along the inside edge of the cut-out line. 1. Check the selected location for the mounting clip, a clear lat area is required, with suficient space around it to place and remove the Fistmic / Handset. 5. Ensure that the unit its into the removed area and then ile around the rough edge until smooth. 6. Drill 4 holes as indicated on the template to accept the ixings. 2. Using a pencil, offer up the mounting clip to the desired location and mark the location of the screw holes on the mounting surface. 7. Remove the backings from the supplied gasket. 8. Place the gasket in position on the back of the unit and press irmly onto the lange. 2. Ensure the bezel is correctly aligned with the unit, as shown. 9. Connect the power, and other cables to the unit. 3. Apply irm but even pressure to the bezel along the: i. Outer edges - work from the sides upwards and then along the top edge, to ensure that it clips securely into position. ii. Inner edges - ensure that the bezel sits lat. 10. Slide the unit into place and secure using the ixings provided. 11. Attach the front bezel. 3. Drill the mounting holes using a suitable size drill bit. 4. Hold the clip in place and secure using the screws provided. 5. Hook the Fistmic / Handset over the clip and gently push down until it clicks into position. 4. Check that all control buttons are free to operate. 12 Ray50 / Ray60 / Ray70 Note: The Fistmic can only be hooked and unhooked from the mounting clip when held vertical. 2. Passive speaker connection. Distribution panel connection 3. NMEA 0183 wires It is recommended that your product is wired through your vessel’s distribution panel via a thermal breaker or fuse. 4. Loud hailer wires (Ray70 only.) 5. In-line 10 A fuse 6. Red positive wire 7. Black negative wire. 8. Vessel’s 12 V dc power supply Warning: 12 Volt dc only This product must only be connected to a 12 volt dc power source. Note: Drill bit, tap size and tightening torque is dependent on the thickness and type of material the unit is to be mounted on. Power connection The power supply should be connected as shown below: Warning: Chassis grounding Do NOT ground this product using the chassis ground terminal. Grounding this product to a vessel’s RF ground may cause galvanic corrosion. Grounding This product is grounded through the 0 V dc negative wire on the power cable and does not require a drain (shield) to be connected to the base station’s ground terminal. 1. Vessel power supply positive (+) 2. In-line fuse. (If your products power cable does not have an in-line fuse then an one fuse should be itted.) 3. Product power cable 4. Vessel power supply negative (-) 5. Vessel distribution panel Battery connection Your product may be wired directly to the battery using an in-line fuse. Warning: Positive ground systems Do not connect this unit to a system which has positive grounding. 1. Base station Breakers, fuses and circuit protection The information below is provided as guidance to help protect your product. The example illustrations provided are for common vessel power arrangements, if you are unsure how to provide the correct level of protection then please consult a Raymarine authorized dealer for support. 1. Vessel power supply positive (+) 2. Vessel power supply negative (-) 3. In-line fuse (If your products power cable does not have a built in fuse then an in-line fuse should be itted.) 4. Product power cable 5. Vessel battery 13 In-line fuse and thermal breaker ratings The following in-line fuse and thermal breaker ratings apply to your product: In-line fuse rating Thermal breaker rating 10 A 7 A (if only connecting one device) Circuit breaker Fuse Where possible, connect individual items of equipment to individual circuit breakers. Where this is not possible, use individual in-line fuses to provide the necessary protection. Connecting the Fistmic – Ray60 / Ray70 Note: • The suitable fuse rating for the thermal breaker is dependent on the number of devices you are connecting. If in doubt consult an authorized Raymarine® dealer. The Fistmic can be connected directly to the connector on the front of the unit. SeaTalkng® connection The product can interface with Raymarine® GPS or GNSS receivers and Raymarine® multifunction displays using the SeaTalkng® connection. A Raymarine® SeaTalkng® GPS or GNSS receiver cannot be connected directly to the product, as GPS and GNSS receivers are powered via the SeaTalkng® backbone. Connecting SeaTalkng® Before connecting to SeaTalkng®, refer to the SeaTalkng® Reference Manual, to ensure that the maximum permitted Load Equivalence Number (LEN), for the SeaTalkng® backbone is not exceeded once this product is connected. • Your product’s power cable may have itted in-line fuse, if not then you can add an in-line fuse to the positive wire of your products power connection. Sharing a breaker Where more than 1 piece of equipment shares a breaker you must provide protection for the individual circuits. E.g. by connecting an in-line fuse for each power circuit. 1. Ensure the Fistmic cable connector is correctly orientated. Positive (+) bar 2. Fully insert the connector into the connector on the front of the unit. Negative (-) bar 3. Rotate the locking collar clockwise until it clicks. 14 1. Rotate the SeaTalkng® connector’s locking collar anti clockwise, to the unlocked position. 2. Ensure the spur cable connector is correctly orientated. Ray50 / Ray60 / Ray70 3. Fully insert the spur cable connector into the SeaTalkng® connector on the unit. 4. Rotate the locking collar clockwise 2 clicks, to the locked position. Controls and interface The controls and interface available are as follows: Base station NMEA 0183 connection The NMEA 0183 wires can be used to connect the unit to a 3rd party GPS/GNSS receiver or multifunction display. 1. PTT (Push to Talk) — Press and hold to send a voice message. Release to return to receive mode. Note: The maximum transmit time is limited to 5 minutes to prevent un-intentional transmissions from occupying the VHF channel. 2. Speaker 3. Microphone location 4. Channel Up and Down — Changes the channel up or down. 1. Built-in speaker 2. Rotary knob / OK push button — Press knob in to access menu / DSC functions and to conirm selections. Turn rotary clockwise or anti-clockwise to move up and down through menu items or to change channel from the Homescreen. 1. Yellow – Receive positive (+) wire. 3. LCD 2. Green – Receive negative (-) wire. 4. VOL/SQ — Turn knob to adjust volume or squelch up and down. Press center button to switch between volume and squelch control. 3. White – Transmit positive (+) wire. 4. Brown – Transmit negative (-) wire. The NMEA wires should be connected to a compatible NMEA 0183 device as shown in the table below: NMEA 0183 wires NMEA 0183 device Yellow – Receive positive (+) to Transmit positive (+) Green – Receive negative (-) to Transmit negative (-) White – Transmit positive (+) to Receive positive (+) Brown – Transmit negative (-) to Receive negative (-) 5. DISTRESS — Push up the spring loaded cover and press this button to make a DSC distress call. 5. HI/LO — Press to switch between High (25 W) and low (1 W) transmit power. 6. 16 / PLUS — When powered on press to switch between priority channels. Powering the unit on With the radio connected to a power supply the power button is used to switch the radio on and off. 1. Press the Power button to power-up the radio. The startup is displayed. 6. 16 / PLUS — When powered on press to switch between priority channels. 7. Power — Press to power the unit on. Press and hold for 3 seconds to power the unit off. Momentary press to access the shortcut list. 8. Back — Move back through menu options. Fistmic The startup screen will automatically time-out after 5 seconds. 2. Press the OK button, or wait for the startup screen to time-out. 15 The Homescreen is displayed. Powering the unit off With the unit powered on: 1. Press and hold the Power button for approximately 3 seconds to power the unit off. Homescreen overview The information below describes the on-screen characters and symbols which the radio displays on the main screen and what they mean. 3. Channel sufix • a — Indicates that the current US or Canadian channel is simplex. This channel uses the transmit frequency of the International channel for transmitting and receiving. If a channel is simplex in all 3 frequency bands (e.g. channel 06, the channel does not require the a sufix. Status bar symbols Icons are displayed in the status bar to indicate the status of the radio. Symbol Name Description Reception signal Indicates the relative strength of the radio signal being received. Displays between 0 bars (no signal) and 4 bars (strongest signal). Transmit Indicates the radio is currently transmitting (e.g. the PTT button is being pressed.) Receive Indicates the radio is currently receiving a transmission Low power Indicates the radio transmitters is in low power (1 watt) or high power (25 watt) mode • b — Indicates that the channel is a receive only channel. Used for Canadian channels only. Note: You cannot transmit on a receive only channel. 4. Channel — Indicates the current channel number 5. Location / Time or Location / COG/SOG — Depending on selection displays Location coordinates and current time or Location coordinates and current COG and SOG. 6. Channel Name — Indicates the name of the current channel. 7. Channel type — Indicates the type of channel: • s = Simplex — Simplex channels transmit and receive on the same frequency. • d = Duplex — Duplex channels use separate frequencies to transmit and receive. 1. Status bar — The status bar displays symbols which indicate the current status of the unit. See Status bar symbols for details. 2. Frequency band — Indicates which channel frequency band is in use: • USA — United States of America • INT — International • CAN — Canada • WX — Weather Note: Special licensing is required to receive USA and Canadian channel sets. 16 High power Local Indicates the radio is in local reception mode, which decreases receiver sensitivity in high trafic areas to decrease unwanted reception Ray50 / Ray60 / Ray70 Symbol Name Description 1. Currently selected menu item DSC Indicates that a DSC call has been received 2. Scroll bar Symbol 3. Menu items Name Sub-options ** Hail/Fog/Intercom • Hailer The main menu includes the following items: Power supply voltage too low Power supply voltage too high Weather GPS Fix Main menu overview Indicates the power supply to the radio is below the speciied operating voltage Symbol Name Sub-options * DSC Calls • Individual call • Intercom ** Hailer/Fog horn • Hailer • Fog horn • Distress call • Position request Indicates the power supply to the radio is above the speciied operating voltage • Group call ** Intercom • Intercom Set-up • Display set-up • All ships call • Phonebook Indicates that the weather alerts mode is activated. Indicates if the radio has a GPS/GNSS ix. • Fog horn • Call logs * Watch Mode * Weather Mode The main menu is accessed by Pressing the OK button from the Homescreen. • Test call • Language • DSC set-up • Units • Dual watch • Power output • Triple watch • Sensitivity • 2nd priority channel • Key beep • Weather Homescreen • Weather alerts • Channel set-up • GPS set-up • DSC set-up * Scan Mode • All channels • AIS • All channels + 16 • Network output • Saved channels • ATIS set-up • Saved channels + 16 • Maintenance • Edit saved channels 17 Note: * Menu items not available when radio has ATIS enabled or if the radio has been pre-programed in MARCOM-C mode. ** The menu name and sub-options depend on the peripheral devices connected to the radio. Shortcut list Pressing the Power button once while the radio is switched on will open the Shortcuts list. The Shortcuts list can be used to adjust the brightness, contrast and access frequently used functions. Initial startup Accessing the menu Unless your radio has been pre-programmed; the irst time you power-up your radio you will be requested to select certain options. With the exception of your MMSI and ATIS ID, you will also be requested to enter these options after a factory reset. The radio’s various options and settings are contained within the menu. After acknowledging the startup screen, unless previously set you will be prompted to make the following selections: 1. Language selection See Selecting a language for available languages. 2. Turn on AIS reception — Ray70 only) Enables the built-in AIS receiver. This step is only applicable to radios with a built-in AIS receiver. See Switching on the AIS receiver for more information. 3. Select network type Selects which connection to transmit AIS and DSC information to connected equipment on. This step is only applicable if the AIS receiver was turned on in the previous step. See Selecting a network type for available options. 4. Enter MMSI number Frequently used functions can be added by selecting Add/edit shortcuts. Adjusting Brightness and Contrast The LCD Brightness and Contrast can be adjusted using the Shortcuts list. From any screen: 1. Press the Power button. 2. Select Brightness or Contrast. 3. Use the Rotary knob to adjust the Brightness or Contrast to the desired level. 4. Press the Power button again to return to the previous screen. 18 Required to enable DSC functions. This option is not required after a factory reset, or if the radio has been pre-programed in MARCOM-C mode, or has ATIS enabled. See Entering an MMSI number for more information. If not already selected you will also be prompted to select your network type. 5. Enter ATIS ID Required when the radio will be used in the inland waterways of Europe. This step is only applicable if the radio has been pre-programed in MARCOM-C mode. See Entering an ATIS ID for more information. 6. Frequency band selection Sets the relevant channels for your region. This step is not applicable if the radio has been pre-programed in MARCOM-C mode. See Changing the radio region for more information. From the Homescreen. 1. Press the OK button. Selecting a language The language the radio uses can be changed. From the Main menu: 1. Select Set-up. 2. Select Language. The languages available are: • English (default) — English • Español — Spanish • Français — French • Deutsch — German • Italiano — Italian 3. Select the language that you want the radio to be set to. The User interface language is changed to the selected language. Switching on the AIS receiver If your radio has a built-in AIS receiver it can be switched on or off. From the Main menu: 1. Select Set-up. 2. Select AIS. 3. Select On. Ray50 / Ray60 / Ray70 Selecting a network type When connecting your radio to other devices it is important to ensure you select the network connection and type that you want data to be transmitted over. From the Main menu: 1. Select Set-up. 2. Select Network type. The following network types are available: • NMEA 2000 (default) — uses the SeaTalkng® connection to transmit data to other devices. • 0183 High speed — uses the NMEA 0183 connection with 38400 baud rate • 0183 Std speed — uses the NMEA 0183 connection with 4800 baud rate. 3. Select the network type relevant to the devices connected to your radio. If your radio is not connected to any other devices any option can be selected. Selecting 0183 Std speed will disable the internal AIS receiver on a Ray70. From the Main menu: 1. Select Set-up. 2. Select DSC set-up. 3. Select MMSI. (Not set) will be displayed if no MMSI number has been set. 4. Use the Rotary knob to cycle through the available numbers and press OK to conirm each number and move to the next digit. You should only enter the unique 9 digit MMSI number provided by your licensing authority. MMSI numbers starting with a ‘0’ are only used for groups and coast stations. If you enter a ‘0’ as the irst digit the radio will assume you are entering a coast station MMSI and automatically assign a ‘0’ as the second digit; this is to ensure a group MMSI is not entered as the radio’s unique MMSI. 5. Press the Back button at any time to edit digits you have already entered. 6. Press and hold the OK button to display options to Move cursor back and forward through the digits. 7. When the inal digit is conirmed select DONE. Caution: MMSI and ATIS ID entry You can only enter the MMSI number and ATIS ID once! If you store an incorrect MMSI number or ATIS ID in your product, it will have to be reset by an authorized Raymarine® dealer. Enabling and disabling ATIS mode ATIS is a European system used on some inland waterways. ATIS must be enabled and a unique ATIS ID entered in order to use ATIS mode. From the Main menu. 1. Select Set-up. 2. Select ATIS set-up. 3. Select ATIS. 4. Select On to enable ATIS mode or Off to disable ATIS mode. With ATIS mode enabled the radio’s region will be ixed to the INT (international) frequency band and the following functions are disabled: Entering your MMSI number To program your radio with your MMSI number follow the steps below. • DSC functions • Watch Mode • Scan Mode • High/low power is restricted on certain channels Once ATIS has been enabled an ATIS ID must be entered. 8. The MMSI is displayed onscreen, check that it is correct, then: i. Select Yes – Save, or ii. if the number entered is not correct select No – Retry. 19 Entering your ATIS ID 8. When the inal digit is conirmed select DONE. When ATIS mode is enabled a unique ATIS ID must be entered. From the Main menu. 1. Select Set-up. 2. Select ATIS set-up. 3. Select ATIS ID. (Not set) will be displayed if no ATIS ID has been set. The irst digit is set to a ‘9’ and cannot be changed, this is because all ATIS IDs start with a ‘9’. As most ATIS IDs consist of a ‘9’ followed by your 9 digit MMSI number; if your radio already has an MMSI number the ATIS ID will be pre-illed in this format. 4. If the ATIS ID has been pre-illed, check it carefully against your issued ATIS ID. 5. To enter your ATIS ID manually, use the Rotary knob to cycle through the available numbers and press OK to conirm each number and move to the next digit. You should only enter the unique 10 digit ATIS ID provided by your licensing authority. 6. Press the Back button at any time to edit digits you have already entered. 7. Press and hold the OK button to display options to Move cursor back and forward through the digits. 20 9. The ATIS ID is displayed onscreen, check that it is correct, then: i. Select Yes – Save, or ii. if the number entered is not correct select No – Retry. 1. Select Set-up. 2. Select Channel set-up. 3. Select Frequency band. 4. Select the relevant region from the list. The available options are: Caution: MMSI and ATIS ID entry • USA You can only enter the MMSI number and ATIS ID once! • CAN = Canada • INT = International If you store an incorrect MMSI number or ATIS ID in your product, it will have to be reset by an authorized Raymarine® dealer. Changing the radio region Prior to using the radio you must set the Frequency band to the region your radio will be used in. From the Main menu: Making a distress call In an emergency you can use your unit to make an automatic DSC distress call. With the spring loaded cover open: Ray50 / Ray60 / Ray70 Making a Mayday call In an emergency you can use your unit to make a Mayday call. 1. Press the 16 PLUS button. 2. Press and hold the PTT button. Cancelling a distress call after transmission A distress call can be cancelled after it has been transmitted. 3. Slowly and clearly speak the details of the distress: MAYDAY, MAYDAY, MAYDAY This is MAYDAY 1. Press and hold the DISTRESS button for 3 seconds. My position is I am Once the DISTRESS button is pressed a 3 second count down will begin, when the count down reaches zero the DSC distress call is transmitted. I have The distress call is repeated automatically until it is acknowledged. OVER 2. Once an acknowledgement is received, or if no acknowledgement is received for 15 seconds; press and hold the PTT button. 3. Slowly and clearly speak the details of the distress in the following format: MAYDAY, MAYDAY, MAYDAY This is MAYDAY I REQUIRE IMMEDIATE ASSISTANCE 4. Release the PTT button. 5. If an acknowledgement is not received then repeat steps 2 to 4 above. Cancelling a distress call before transmission 1. Select Options. 2. Select Cancel distress. My position is To cancel a distress call before it is transmitted follow the steps below: 3. Select Yes to conirm cancellation. I am 1. Release the DISTRESS button before the count down timer completes. 5. Press and hold the PTT button and make a broadcast to all stations giving your vessel’s name, call sign and MMSI number and cancel the false distress alert I have I REQUIRE IMMEDIATE ASSISTANCE OVER When the button is released you will be returned to normal operation. 4. Select OK. Example: “All, Stations, All Stations, All Stations. This is , , , 4. Release the PTT button. 21 3. If the distress call is not acknowledged by another station then acknowledge the call as follows: . Cancel my distress alert of ,
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Compression Level : 6 Compression Type : auto Config File : C:\program files\ptc\arbortext pe\lib\standard.pdfcf Create Date : 2014:10:02 08:29:14+01:00 Creator : Arbortext 5.4 EPS Processor : PStill version 1.74.14 Graphics Resolution : 600 Graphics Resolution Threshold : 900 JPEG Quality : 80 Modify Date : 2015:02:18 09:03:35-08:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Creator Tool : Arbortext 5.4 Metadata Date : 2015:02:18 09:03:35-08:00 Graphics 0020resolution : 600 JPEG0020quality : 80 Compression 0020type : auto EPS0020processor : PStill version 1.74.14 Config 0020 File : C:\program files\ptc\arbortext pe\lib\standard.pdfcf Compression 0020level : 6 Graphics 0020resolution 0020threshold: 900 Producer : PDFlib+PDI 7.0.4 (Win32) Format : application/pdf Document ID : uuid:5643e99b-3b2a-46ef-9791-591c05245f7a Instance ID : uuid:40849707-8289-4fb7-98d2-3cc1f16d16bf Page Layout : SinglePage Page Count : 23EXIF Metadata provided by EXIF.tools