Flying Technology FY-919 Remote Control User Manual
FLYING TECHNOLOGY INDUSTRIAL CO.,LTD Remote Control
User Manual
Instruction Manual of FY919
Key function on the transmitter
1. ON/OFF 2. One-key Calibration 3. Non-head mode 4. Auto-Launch/Land
5. One-Key Backward 6. Speed switch 7. Emergency Stop 8. Beginner Mode
9. Throttle&Rotation 10. Direction 11. Power indicator
12. Yaw trim 13. Direction trim 14. One-Key Rotate
(Function of Specific version)
Attention
Please read this Safety Warnings listed below before your first flight. Failure to comply
with the following recommendations could lead to injuries. The RC aircraft is not intended for
those under 14 years of age without proper adult supervision.
Warning
*Please follow the instruction or packing instructions for proper installation and use. Some
parts should be assembled by the adult.
*The product contains small parts which can lead to eating or possible choking hazard.
*Please put away the packing material in time to avoid causing harm to children.
*It is necessary to regularly check the charger, wire plug, shell and other component. And
please stop using the product until the repair if you found any damage.
*The charger, the battery pack, and the charging device must be inserted in the same power
as the product labeling.
*Do not puncture or short the battery to avoid fire.
*Please DO use the original configuration of the charge. And the charger is not a toy.
* Disconnect the charger when Cleaning toys.
*Non rechargeable battery can not be charged.
*It is necessary for the adult guardianship when charging the rechargeable battery.
*Do not mix old and new batteries or different types of batteries and the exhaustion of
battery should be promptly removed.
*Do not break down or short-circuit the battery, even throw into the fire.
*Please take out the battery if did not control the product in a long time.
*Do not touch the rotating parts to avoid causing harm to the body.
*Please stop the motor when the paddle has seized�up to avoid overheated danger.
*Please do not seriously impact or drop aircraft and remote control.
*Please fly in sight to avoid losing the aircraft because of out of control.
*Clean the product with a clean and soft cloth.
*Users are responsible for ensuring that the product will not cause damage to itself or
others. The Manufacturer or distributor will not take any responsibility for the operation
of the operation of the damage caused by improper operation of their own or other people’s
safety.
1.Plug the USB charging cable into the mobile phone adopter USB port. Then the
indicator light of charging cable will turn red.
2.Then insert the charging plug of the USB charger correctly into the charging cable
correctly. Then the indicator light of USB will flash green.
3.Charging for about 90 minutes. Then the USB indicator will light green which means
the charging has been finished. Please cut off the connection and move them to the
save place.
List of product configuration and parameters:
Configuration list : Aircraft*1, Remote Control*1, 7.4V lithium-ion battery(built-in)USB
charger*1, The instructions*1, Propeller*4
Battery(Aircraft): 7.4 V 350mA lithium batteries Remote control radius：≥30m
Battery(Remote Control): 4 grain of 1.5V AAA battery（another purchase）
Flying Time：5 min Aircraft Size: 139mm* 139mm* 51mm
Aircraft Weight: 92g Packing Size: 325* 85* 195 mm
Battery Loading of the transmitter
Remove the battery cover of the transmitter. As the polarity shown in the battery
compartment, please correctly load 4PCS AAA batteries (not included). Then please
load the battery cover.
(Please DO remember to pull the ON/OFF power switch to the OFF position before
charging.)
Caution:
A.When loading the battery, please make sure correct the polarity of the battery and
battery compartment. Please DO NOT load the batteries upside down.
B.Please DO NOT mix the old batteries with the new ones or batteries of different
types.
Charging Instruction of the lithium battery
Caution of lithium batteries related operation
Preparation before operating the aircraft.
Frequency Match
A：It is necessary to pay attention to when charging and do not leave the machine alone.
And please stop if the battery get thermal during charging to avoid battery damage or fire,
etc.
B: Do not charge next to the inflammable and explosives. And please stop using the battery
if got thermal, metamorphous or discoloring when charging suddenly.
C: Pay attention to your skin and eyes when the battery leaks. And please rinse with plenty
of water if connect with skin or eyes. Then seek for medical attention.
D: Please choose the original configuration charger and ensure that the Voltage of the
charger is suitable for the local standard
E: Please do not put the battery into the fire, microwave or pressure vessel.
F: Please do not clean through the solvents, industrial alcohol or flammable solvent.
G: This product is combined with plastic, electronic and battery. Please deal according to
the local garbage collection requirement.
1. Battery loading and power-on: Load the battery into the battery box as the picture A
shown and ensure to connect with the right power plug.
2. Caution: When connecting the power plug, please ensure the “+””-”polarity while the
red line to “+”.
1. Please connect correctly the power socket of the Quad-rotor and the battery plug, and
then point the tail of the Quad-rotor will be quickly flashing and please DO NOT move the
fuselage.
2. Press the ON/OFF of the RC, and you will hear one sound of “di...di...” sending out
from the transmitter. This time the power indicator of the transmitter and the LED light of
the Quad-rotor will keep eternal bright ”ON”, which represents the decoding is success-
fully finished and you can operate and control the Quad-rotor.
3. When control several drones, please ensure to be on code one by one and to avoid error.
Aircraft starting/Landing Control Method
Basic Operation Guide
Start/Landing
A: Start/Landing
1. Press the Start/Landing switch. Then the aircraft will launch to 2m automati-
cally.
2. Press the Start/Landing switch during the flight, the aircraft will descend to
the ground in smoothly.
B：Emergency Stop
Please quickly press the Emergency Stop Key twice when the aircraft is fallen off
by accident or occur to the danger. The aircraft will stop working immediately.
Emergency Stop
Tips: Push upward the throttle lever and the aircraft will raise to the assigned height. Then please
loosen the throttle lever and the aircraft will be flying steadily as per this height.
Ascending
Descending
When pushing the throttle stick
upward, the aircraft will be
ascending;
When the throttle lever is
pushed down, the aircraft
drops;
When pushing the throttle stick
to the left, the aircraft will turn
left
When the throttle lever is
pushed to the right, the aircraft
turn right.
Turn-left
Turn-right
Forward
Backward
When pushing the direction
stick upward, the aircraft
will be advancing forward.
When the direction of the
lever back to pull down, the
aircraft fly backward.
When pushing the direction
stick to the left, the
aircraft will fly to the left
side.
When the direction of the
joystick to the right,
aircraft fly on the right
side.
Left-side Right-side
Operating method of the non-head mode
Non-Head Mode ON/OFF 1. Firstly, please kindly confirm the forward direction before
entering into the none-head mode. Press the key of the non-head mode.
The power indicator will flash 3 times, which means that it has
entered into the non-head mode. Regardless of the direction, the
aircraft will fly to the direction confirmed at the beginning.
2.If you need to exit the non-head mode, please press the key of
non-head mode to exit. When the Blue LED on the head of aircraft stop
flashing, the non-head mode is OFF.
Tips: The following direction under the non-head mode is the forward direction when the decoding or
calibrating is made. When entering into the non-head mode, the aircraft can rotate to either direction,
its forward direction still be following the forward direction when the calibrating is made.
Beginner Mode
Trim & Calibration of the Drone
The Max height of flight when under beginner mode is 2-3 m
Push slowly the throttle lever. When the aircraft ascending till about 1.5 meters, if
the aircraft make spinning in the air or titling toward different direction still be
following the forward different direction. Its forward direction still be following
the forward direction when the decoding, you can fine-tune to correct the action.
Move
forward
Move
backward
When deviating toward forward,
please trim it to the back until
it is well repaired.
When deviating toward backward,
please trim it to the forward
until it is well repaired.
When deviating to the left,
please trim it to the right
until it is well repaired.
The deviating to the right,
please trim it to the left,
until the repair.
Move to
the left
Move to
the right
One-key Calibration（Please place the remote control
on the ground）
Loading & Unloading BATTERY
As the picture shown below, firstly, please press the arrow area, turn the battery
door to the right and you can unload the battery.
Aircraft WIFI mobile control and real-time transmission instructions
1、Please download the APP
2、Connect the WIFI in the setting on the mobile phone (There will
be no password)
3、Click the Flying 3D to into the APP.
4、The throttle will be hide when stand for 3 s.
5、Click the Hide interface and then the main interface will be
hided
Photo Video Browse View VR Video View
Rotate
Throttle & Steering Gyro control Direction
Loading and unloading method of the protective ring of the aircraft
Turn the protective ring to the left and you can unload the protective ring as
the picture shown below.
Turn the protective ring and you can lock it tightly as the picture shown below
Turn the protective ring to the right and you can lock it tightly as the picture
shown below.
APP Store Google play
Problem Solving Guidelines
Question Reason Treatment
Powered cannot
control
Severe shock
Aircraft from
total flying
to one side
Out of control
Cannot take
off
Landing too
fast
Remote control and aircraft
power supply bad.
The remote control and aircraft
to code without success.
Check and Charge the battery
according to battery installa-
tion instructions. The code the
aircraft.
Re-code according to the front
of the code description.
The rotor deformation. Replace the new corresponding
rotor.
Hollow shaft bending.
The rotor deformation.
There is a motor damage.
The aircraft is not horizon-
tal when code.
Beyond the remote control
distance.
The rotor rotating speed is
too slow
Aircraft battery shortage
Quickly back to the throttle
lever
There are more than one
aircraft turn on the power
during binding.
The replacement of the new
rotor.
Replace the new corresponding
motor.
Push the One-key Calibration.
Control in the distance of
30m
Please re-code (It is neces-
sary to bind one by one.)
Will throttle control lever
slowly push up
Replace the full battery or
battery full of power Re-con-
trol
Let the aircraft fall, please
slowly pull back the throttle
control lever.
Replace the new hollow shaft.
Accessories List
NO QuantityPatrs
Rear Wing
Protective Cover
Reversal Propeller
Forward Propeller
Cover
Bottom
Screw
Motor
Motor
Ornament
Optical Module
Battery
Battery Cover
WIFI Module
Motor Seat
Arm Tube
Main Circuit Board
Gyro Seat
Gyro Board
Press block
12
FCC STATEMENT
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body